emutel Maestro User manual Rev 2.3b
Contents
1. lift it straight up leaving the base on the worktop 6 Remove the two fixing screws off the particular module you wish to replace Figure 4 indicates both modules fixing screws Important Note Please refer to the Modules cross Reference Table for valid module configurations 25 APPENDIX Figure 4 DSL Module Fixings 7 Placing your fingers firmly under the back and front edges of the module prise gently to extract the module See Figure 5 Figure 5 DSL Module Removal Important Note Please ensure that when the module is being extracted that both ends are lifted simultaneously This will avoid damage to the connectors 26 10 11 12 13 14 15 16 17 18 19 APPENDIX Place the new module in exactly the same position taking care to align the connectors Press the module firmly above each connector to feel the positive fit of the connectors It may be necessary to place finger below the motherboard for support and to ensure a good contact Inspect the connections to ensure they are correctly seated Refit the two fixing screws back into place as in Figure 4 Replace the lid taking care to align the feet on the base correctly Refit one screw on each of the sides of the enclosure Reconnect the electric power lead Connect the Maestro to a PC using the RS 232 lead Upload the Maestro code supplied for the DSL module using the Configuration Software Power off the emu2. ports or just for configured channels LED 5 indicates data being received and LED 6 indicates data being transmitted LEDs 3 amp 4 will be used for future development The LINE LED refers to the unit being configured to accept an external baseband telephone system via the LINE port POTS or ISDN LINE Connections The emutel Maestro provides the option for either 1 Plain Old Telephone System POTS or 1 ISDN connection and 1 ADSL simulation concurrently on the same CO port POTS ISDN equipment can be connected directly to the CO interface or through a splitter if ADSL terminal equipment is to be connected simultaneously UTOPIA Connections The emutel IMaestro provides a Level 2 Direct Status Indication UTOPIA interface The PHY addresses are configurable using the Configuration Software These connections allow direct access to the ATM data stream in and out of each xDSL CO port Terminal Port A V 24 port is provided allowing the connection of the Ethernet Port PRODUCT SPECIFICATION Configuration Software via PC with a serial port An IEEE 802 3 Ethernet port is provided for connection to the Configuration Software using a local area network running TCP IP protocol LEDs indicate 1 network present 2 network activity INSTALLATION Unpack the emutel IMaestro First unpack the emutel IMaestro and check for signs of damage in transit If the unit or packaging is damaged this should be reported immediately to ar
3. IA 5 7 o oO ANA AB BB IHR IR WIW Iw l w lw IN IN IN IN NS gt gt SS s Io fw lo N Aa MO N JO W sO IN OO Ww a WIA NO IN JO W gt Not Connected Not Connected Not Connected Not Connected Not Connected Not Connected Not Connected Not Connected UTOPIA RX DATA 0 UTOPIA RX DATA 1 UTOPIA RX DATA 2 UTOPIA RX DATA 3 UTOPIA RX DATA 4 UTOPIA RX DATA 5 UTOPIA RX DATA 6 UTOPIA RX DATA 7 Not Connected Not Connected Not Connected Not Connected Not Connected Not Connected Not Connected Not Connected Not Connected UTOPIA RX SOC 3 UTOPIA RX ENB 5 UTOPIA RX ADDRESS O 5 UTOPIA RX ADDRESS 1 9 UTOPIA RX ADDRESS 2 61 UTOPIA RX ADDRESS 3 63 UTOPIA RX ADDRESS 4 2 Ground 4 Ground 10 Ground Ground 58 Ground 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 62 64 33 UTOPIA RX CLAV O UTOPIA RX CLAV 1 UTOPIA RX CLAV 2 UTOPIA RX CLAV 3 UTOPIA RX CLK Do not use Do not use Do not use Terminal port pin out APPENDIX 66 Ground 68 Ground Ground 80 Ground DCD 16 DSR RXD 20 5 ay kaaa TXD T 30 8 CTS DTR oN 9 N C GND 50 9 WAY FEMALE D TYPE CONNECTOR Figure 3 V 24 Terminal Port Data Carrier Detect always active Received Data output Transmitted Data input Data Terminal Ready input ignored Ground Data Set Ready always active
4. Request to Send input active to allow emutel Maestro to send Data Clear to Send output active when emutel IMaestro can receive Data 34 APPENDIX This a description of the LED indicators on the front and back LEDs panels This port is used to connect to the external POTS ISDN network The xDSL module has been detected The port is in the showtime state Future development Future Development Indicates data being transmitted from xDSL Indicates data being received by xDSL System Alarm 35 Definitions AALO AALS ADSL ANSI ATM ATU C ATU R BER BRI co CPE DSL DSLAM FTP HTML ISDN LAN LCD PC POTS PSTN SHDSL VCI VDSL VPI GLOSSARY ATM Adaption Layer O ATM Adaption Layer 5 Asymmetric Digital Subscriber Line American National Standards Institute Asynchronous Transfer Mode ADSL Transceiver Unit Central Office ADSL Transceiver Unit Remote Bit Error Rate Basic Rate Interface Central Office Customer Premise Equipment Digital Subscriber Line Digital Subscriber Line Access Multiplexer File Transfer Protocol HyperText Markup Language Internet Protocol Integrated Services Digital Network Local Area Network Liquid Crystal Display Personal Computer Plain Old Telephone Service over PSTN Public Switched Telephone Network Symmetric High speed DSL Virtual Channel Identifier Very high speed DSL Virtual Path Identifier 36
5. are fails to connect to the emutel Maestro through the Ethernet port then first check that the unit is on If the unit is on then check that the correct leads are connected to the correct ports for example LAN port and not the 10Baset port If you are connecting your PC directly to the LAN interface you will require a cross over cable whereas if you are connecting via a hub you will require a straight through cable If the unit still does not respond then check the connection setup in the Configuration Software by referring to the online Help If this fails try connecting using the serial port If this fails refer to the section below In the event that the Configuration Software fails to connect to the emutel Maestro using the Terminal port then first check that the unit is on If the unit is on then check that the correct leads are connected to the correct ports If the unit still does not respond CHAPTER 3 16 Unit fails to display status of module emutel Maestro fails to respond after a setting is changed Traffic is not being passed through to the ATM port FAULT FINDING then check the connection setup in the Configuration Software by referring to the online Help If this fails execute the Restoring Default Settings procedure given in the Quick Reference Guide section If the LCD does not display the status of a module then the module has not been recognised by the unit Try powering the unit off then wait a
6. ca technologies Take an Inventory Take an inventory of the parts supplied Check that the items ordered were actually received The list below should be of help in identifying each part emutel Maestro Cable for serial connection RS232 2 off RJ11 Modem Leads Mains Cable This Manual Configuration Software CDROM Connect to a PC or terminal Plug the serial cable into the Terminal port at the rear of the unit and connect to a PC emutel IMaestro default terminal settings are 19200 baud 8 data bits no parity 1 stop bits Power The emutel Maestro will operate on a mains voltage of 110 240V a c 50 60HZz Connect power Plug the power cable into the rear of the unit and power on using the switch located on the mains inlet Power should be supplied via an IEC mains lead supplied Warning The power supply must have a protective ground earth If not the mains filter will force the metal case to a voltage equal to half the mains supply voltage Configure emutel Maestro Install the Configuration Software from the CDROM provided refer to Configuration Software section From the Comms menu select Connect A pop up screen will appear showing the progress as the Configuration Software reads the unit s configuration data The unit should have the factory default settings but to be certain reset the unit using the Reset command in the System menu During this procedure there will be two pop up screens
7. d POTS ISDN terminals to be connected simultaneously via an external splitter to allow full interoperability testing and demonstration The POTS and ISDN interfaces can be provided by an external POTS IDSN U interface device connected via an external splitter to the LINE ports There are no user serviceable parts inside emutel Maestro The unit should only be opened by approved maintenance staff otherwise the warranty will be invalidated PRODUCT SPECIFICATION xDSL Connections The emutel IMaestro xDSL Central Office CO interfaces can be configured to operate in various modes however these may change depending on the chipset currently fitted within the unit Multimode operates by choosing the best mode for operation with the connected Customer Premise Equipment CPE Other operational parameters and data can be altered or read with the Configuration Software The CPE can be connected directly to the interface or through a splitter if POTS ISDN terminal equipment is to be connected simultaneously LED s indicate the operating status of each interface For example LED1 indicates configuration parameters have been accepted and the chipset is attempting to make a DSL connection LED2 indicates Showtime has been achieved between the module and the external modem equipment LED 5 and 6 indicate traffic passing through the Maestro They can be made to operate for either any data being received transmitted over the xDSL
8. do not show the same information then click on the REFRESH button This updates the emutel Maestro with the settings already in the Telebyte After changing any parameters in the Telebyte tab it is necessary to click on the APPLY button to send the new settings to the Telebyte 29 APPENDIX Pin Outs xDSL CO Pin out The following table shows the pin out of the RJ11 connector for the ADSL CO interfaces LINE Pin out The following table shows the pin out of the RJ11 connector for the LINE external baseband telephone system interfaces RJ11 connector TIP 5 nc EIN 3 EIN See in RR Gaara nN 4 Figure 1 RJ11 plug front view 30 APPENDIX Ethernet interface Pin out The following table shows the pin out of the RJ45 connector for the Ethernet interface R145 connector Figure 2 RJ45 plug front view UTOPIA TX Pin out The following table shows the pin out of the 80 way High Density connector UTOPIA 5 Not Connected 6 Ground 7 _ Not Connected 8 Ground 9 Not Connected 10 Ground 31 30 38 46 54 59 UTOPIATXADDRESS2 60 Ground 65 UTOPIATXCLAVO 66 Ground 167 UTOPIATXCLAV1 68 Ground 69 UTOPIATXCLAV2 70 Ground 179 Donotuse 80 Ground APPENDIX 32 UTOPIA RX Pin out APPENDIX The following table shows the pin out of the 80 way High Density connector UTOP
9. ed The default directory is C Program Files Arca Technologies Click browse to select a different directory to install to Click Next to continue Choose Destination Location Select folder where Setup will install files 7 The Select Program Folder dialog will appear Click Next to continue InstallShield Wizard Select Program Folder Please select a program folder Dell Documents Egg Invaders InstallShield Professional 2000 InterVideo WinDVD Microchip MPLAB 8 The installation will then begin as the following dialog appears The dialog will disappear when set up has been completed 9 Finally a dialog shall appear to indicate the installation has been completed CHAPTER 2 10 CONFIGURATION SOFTWARE InstallShield Wizard InstallShield Wizard Complete Setup has finished installing Emutel Maestro Software on your computer lt Back Cancel 10 Click Finish to dismiss the dialog Running the Configuration Software From the Start Menu go to the Programs Directory and select emutel Maestro Software from the sub menu The Software will then load and the main application window will be displayed SS ini x Pie n Yam Comme My Mako kak Dap bhewess trdormationy poet RE ee MT Globeapangeeeil A ascatet CO ATM Cantiguration Telelyte Gore Satins Oren Mode sine Eenemeniini MEET DM rosa am sj Men FT Fug Stinks Tice IKE lange fi tf Heroe Dainese tin
10. emutel Maestro Gs SN xDSL Simulator Installation and Trouble Shooting Guide arca technologies arca technologies 2 Trench Road Mallusk Technology D evelopment C enter Belfast BT 36 4TY 545 Boylston St 3 Floor N orthern Ireland Boston MA 02116 T 44 0 28 9084 5700 T 001 800 375 9925 F 44 0 28 9084 5701 F 001 617 262 9484 E info arca technologies com W www arca technologies com Revision 2 3b Document released 26th January 2005 TABLE OF CONTENTS Table of Contents Introduction cece Page 3 Product Specification nn Page 4 Installation OCT Page 6 Configuration Software Page 8 Fault Finding O CT Page 16 Quick Reference Guide Page 19 Appendices Uploading Maestro Code Page 20 Upgrading ATM Code Page 22 Upgrading Website Code Page 23 Module Replacement Page 24 Telebyte Tab Page 28 Pin Outs 7 Page 30 LEDS sisser Page 35 Glossary 9 Page 36 The emutel Maestro INTRODUCTION Thank you for choosing emutel IMaestro a powerful tool for developers manufacturers and resellers of xDSL products emutel Maestro replaces the requirement for an xDSL ADSL SHDSL or VDSL line from a Central Office DSLAM emutel Maestro is available with several different manufacturer Central Office interfaces and connection to an external baseband telephone system via the LINE interface emutel Maestro allows ADSL an
11. fault settings and will re establish communication with the emutel IMaestro The second method needs a Communication package such as Hyper Terminal The procedure is as follows 1 Set the com port to 19200 baud No parity 1 Stop bit 8 Data bits 2 Hold down lt CTRL gt and lt C gt on the keyboard Switch on the emutel IMaestro 4 Wait until the screen appears with a number of RESET commands When the unit is first switched on the terminal port will search for a lt CTRL C gt being transmitted to the emutel IMaestro If this occurs the emutel IMaestro will restore the factory defaults otherwise it will use the previously stored settings Type lt F1 gt at any stage and the help screen shall appear CHAPTER 4 19 Uploading Maestro Code using the Configuration Software Maestro code APPEND In order to uploadthe Maestro code the user will first need to start the Configuration Software Please ensure that all cables are disconnected from the unit except for the power and serial cables Ensure that the emutel IMaestro is connected to your PC via the RS232 connection and that communication has been established using the Comms pull down tab and the Connect option see section Connecting via serial port Maestro code is for the main part of the emutel IMaestro Whereby you are required to load the appropriate Maestro code which matches the module type fitted into the unit There are se
12. few seconds and power it on again If the LCD displays Inactive beside the CO port this indicates that the firmware currently installed is not compatible with the current module configuration Refer to the compatibility table in the appendices If this occurs the simplest method to recover is to follow the Restoring Defaults procedure given in the Quick Reference Guide section Settings will only be applied once the Apply button has been selected Check that the appropriate ATM settings have been setup within the ATM configuration tab Settings that have been used by Arca Technologies are as follows For connection through to the ATM port VPI 8 VCIz80 MPHY MOD1 or 2 AAL Type AALO Cell Rate 10000 VPI 0 VCI 80 MPHY ATM AAL Type AALO Cell Rate 10000 For connection through to the Ethernet port VPI 8 VCl 35 MPHY MOD1 or 2 CHAPTER 3 17 FAULT FINDING AAL Type AAL5 Cell Rate 10000 Ensure that the correct ATM connection is being used Multimode and Single Mode ATM boards are available CHAPTER 3 18 Restoring default settings Accessing online Help QUICK REFERENCE GUIDE To restore the emutel IMaestro to factory defaults you can use either of two methods The first method uses the Configuration Software Select the SYSTEM pull down tab and click on the RESET option A dialog box will appear instructing you to power cycle the unit This will reset the emutel Maestro to the factory de
13. n Equipment Requirements Important Note Procedure HAZARD WARNING Figure 1 Front Panel Fixings APPENDIX Due to the nature of the APls it is not possible to have Maestro code to support plug n play For this reason the procedure for replacing a module shall also require a firmware upgrade 1 off Pozidrive screwdriver 1 off RS 232 9 9 way lead 1 off Electric Power lead 1 off PC with emutel Maestro Configuration Software Please ensure that all fixings removed during disassembly of the emutel IMaestro are retained for refitting during reassembly The first stage shall be to remove the lid off the emutel Maestro The mains supply must be switched off and the power lead disconnected before the lid is removed as there are hazardous voltages present 1 Looking at the front panel of the emutel IMaestro as in Figure 1 remove the 5 screws indicated Pu s 2 Rotate the emutel IMaestro 90 degrees Now looking at the side panel of the emutel IMaestro as in Figure 2 remove the 4 screws indicated 24 APPENDIX Figure 2 Side Panel Fixings 3 Rotate the emutel IMaestro 90 degrees Now looking at the rear panel of the emutel IMaestro as in Figure 3 remove the 4 screws indicated Figure 3 Rear Panel Fixings 4 Rotate the emutel IMaestro 90 degrees Now looking at the side panel as in Figure 2 remove the 4 screws indicated 5 Taking care not to scratch the lid
14. off and back on 22 APPENDIX Upgrading Web site code Web Site code is for the Internal Web Server within the ATM part of the emutel IMaestro To load new Web Site code select the SYSTEM pull down tab followed by the Upload Internal Web Server option Either enter the full file name and path or use the Browse button to select the file for uploading into the emutel IMaestro Once the file has been selected click on the START button You should now see 4 LEDs 2 3 5 and 6 of Port 1 on the front of the emutel IMaestro rotating in sequence You should also see the Upload Progress bar slowly moving across Do not switch the emutel Maestro off File ToUpioad CAP og an Faso Tectndiog a Lod Ward Eromsa Upload Frogwsis BRURERARNNERNERENNNNNNNI Upa cords man Mansiin Derk EEE res FIT FED tates el er al Once the above message appears you should click on the Close button and then switch the emutel IMaestro off and back on to complete the reprogramming Re connect to the emutel Maestro using the Comms pull down tab and the Connect option Now check that the software has been correctly recognised by the emutel IMaestro by using the System pull down tab and the Configuration option Finally perform a System Reset using the System pull down tab and the Reset option After waiting for the reset process to finish please switch the emutel IMaestro off and back on 23 DSL Module Replacement Introductio
15. ower on the Telebyte wait until its display shows the current distance configurations of the line cards and then power on the emutel IMaestro This sequence allows the emutel IMaestro to check for the presence of the Telebyte at power on If the emutel Maestro is powered on first it will not detect the Telebyte when it is switched on If you wish to remove the connection to the Telebyte and communicate with the emutel IMaestro using the serial lead it is necessary to power down the emutel IMaestro connect the emutel Maestro to the PC using the supplied serial lead and then power on the emutel IMaestro The emutel Maestro determines its configuration of the serial port for communication with the Telebyte or PC only at power on Whenever the Windows Application is started and communications with the emutel IMaestro has been established there will be a tab 28 APPENDIX for the Telebyte if it has been correctly detected If the tab is not present then check the connections and repeat the power on sequence above The above is an example of the Telebyte tab within the Windows Application For more information on the operation of the Telebyte see the relevant section of the Windows Application Help Not all of the commands in the Telebyte manual are supported so for Command Line Interface CLI please refer to the CLI manual and use the commands detailed there If the display on the Telebyte and the emutel IMaestro
16. stro via the RS232 connection and the configuration settings will be read from the unit The online help describes in detail all of the parameters that can be configured Refer to the online help for full descriptions of these parameters ai Pie CE Vem Core Dein tele Uk Depthrecs maton mr U rez I Ti hmm Port 1 Ghebespaniiell A ATM Conliguraties vi 10 Tren Mode hide TERN 7 feaa fie ata fined sj TO ak FRerete Dota bite Nccrei fe tom Eiern gt kn LO Can TO h g 7 Tage TO fee 7 Btm T e GRE re Limen Bi Setings Me Mom E Mes AS Fant verted rs Inte owing Delay Tews Wiutaworg Dawcion Taw ovate 1 Unerereon bit Seinge Vena of Nie Monk fF Mean bifmeikieef AS Fact vha fx bieteowptioy TENE Ietetrowg torsion Tire ati In order to connect to the emutel IMaestro via the LAN interface you must configure the appropriate IP settings In order to change the emutel IMaestro IP settings it is necessary to connect via the RS232 port as described above Once connected go the System drop down menu and select Set Maestro IP CHAPTER 2 13 CONFIGURATION SOFTWARE Emutel Maestro Software File Edit View Comms System Help Reset emutel Mae configuration Set Maestro IP The emutel IMaestro IP address dialog will appear Mnesim IP Address Kasstoaddiess 19 168 0 131 IP Subrnask 256 256 pes ceren The default IP address submask and gate
17. tel Maestro Power on the emutel Maestro taking note of the module description on the front panel display If the module has been identified correctly and goes into TRAINING then the uploadwas successful and the remaining screws should be fitted to the enclosure Place the old module into the protective packaging that the new module was supplied in 27 Telebyte 458 2SL 2 port Line Simulator Power on sequence e APPENDIX The emutel IMaestro is capable of controlling the 2 port Line Simulator from Telebyte Inc of Greenlawn New York www telebyteusa com The Telebyte is connected to the emutel Maestro using a serial lead which means that the emutel Maestro must be controlled from the Windows Application using it s 10Base T Ethernet port See the section above marked Communicating via Ethernet port on how to set this up The Telebyte is connected to the emutel IMaestro using a Male Male 9 way D serial cable with the following wiring Maestro Telebyte Pin 1 Pin 6 and Pin 8 Pin 2 Pin 3 Pin 3 Pin 2 Pin 5 Pin 5 The 9 way D with the loop between pins 6 amp 8 should be connected to the Telebyte Power on the Telebyte Connect using the above serial cable Connect the emutel Maestro to the PC using an Ethernet cable Power on the emutel IMaestro Start the Windows Application on the PC and Connect to the emutel Maestro using Ethernet If the two units are already connected then p
18. the Reset option After waiting for the reset process to finish please switch the emutel Maestro off and back on 21 Upgrading ATM Code APPENDIX ATM code is for the ATM board within the emutel IMaestro To load new ATM code select the SYSTEM pull down tab followed by the Upload ATM Code option As before either enter the full file name and path or use the Browse button to select the file for uploading into the emutel Maestro Once the file has been selected click on the START button You should now see 4 LEDs 1 2 4 and 5 of Port 1 on the front of the emutel IMaestro rotating in sequence You should also see the Upload Progress bar slowly moving across Do not switch the emutel Maestro off Fit Topload CP gran Fh Aca Technodogs Lid Vera Browse Upload Progress LULU an Uplasd comglete ese Matsin Sert 21519 records TAMH D bytes aa cr ms Once the above message appears you should click on the Close button and then switch the emutel IMaestro off and back on to complete the reprogramming Re connect to the emutel IMaestro using the Comms pull down tab and the Connect option Now check that the software has been correctly recognised by the emutel IMaestro by using the System pull down tab and the Configuration option Finally perform a System Reset using the System pull down tab and the Reset option After waiting for the reset process to finish please switch the emutel Maestro
19. the first indicating a Reset command and the second showing the new settings being read from the unit CHAPTER 1 6 INSTALLATION Connecting Terminal Equipment The connections on xDSL CO1 and xDSL CO2 allow the user four possible connection scenarios Direct connection of xDSL CPE Combined connection of ADSL CPE and POTS Equipment using a Splitter Annex A Combined connection of ADSL CPE and ISDN Terminal Equipment using a Splitter Annex B Connection of an external baseband POTS ISDN telephone system with external splitter N B Make sure that the equipment is compatible with the interface it is connected to Connecting an External Baseband Analogue If you require the use of an external POTS system connect the Telephone System external POTS system to the corresponding Line port via an external POTS splitter Connecting an External Baseband ISDN If you require the use of an external ISDN system connect the Telephone System external ISDN system to the corresponding Line port via an external ISDN splitter Connecting UTOPIA Equipment If you require connection to the UTOPIA bus then two 80 way High Density connectors should be used The connections are shown in the Appendix Go to the System menu option and select xDSL gt Utopia All data will be directed to the Utopia ports at the back of the unit CHAPTER 1 7 Installing the Configuration Software CONFIGURATION SOFTWARE 1 Insert the emutel IMaestro Sof
20. tware CD into the CD drive of your machine If autorun is enabled on your PC then the installation will begin automatically Otherwise read the contents of the CD via Windows Explorer and double click setup exe 2 The following dialog will appear InstallShield Wizard A Emutel Maestro Software Setup is preparing the InstallShield er Wizard which will guide you through the rest of the setup process Please wait Wait until the status bar at the bottom of the dialog has completely filled 3 The welcome screen will appear Click the Next button at the bottom of the window old Wird Walco to the Irainlifiteek Witard tur Emutet Maneto Satan Tite la Kae Shati Vidor wi mad Esai Meese Softwa unya compute To contre cick Mert 4 The License agreement will appear Click Yes to accept CHAPTER 2 8 CONFIGURATION SOFTWARE InstallShield Wizard License Agreement Please read the following license agreement carefully 5 The Customer Information Dialog will appear Enter your name and your company name into the boxes provided This information must be entered before you can proceed Click on the Next button to continue the installation j InstallShield Wizard Customer Information Please enter your information Arca Technologies Ltd iste Einleleh CHAPTER 2 9 CONFIGURATION SOFTWARE 6 The next dialog that appears will allow you to choose the directory into which the software will be install
21. u within the configuration software CHAPTER 2 15 Introduction Unit does not power up Showtime does not occur Configuration Software does not connect to the emutel Maestro using the LAN port Configuration Software does not connect to the emutel IMaestro using Terminal Port FAULT FINDING This section seeks to provide some guidance on solving common problems encountered in using emutel IMaestro Check to see if the internal cooling fan is operating If the fan is working correctly you should hear a whirring sound If the fan is not operational then look at the LEDs and LCD If these are also off then check the mains lead is connected properly If the mains lead is connected properly then check that the mains switch on the rear of the emutel IMaestro is on If so then test your mains supply by plugging in another piece of equipment i e use a table lamp If the power supply is present then try a new supply lead Assuming the emutel IMaestro and CPE are powered on set the connection variables to default by following the procedure for a system reset detailed in the Quick Reference Guide section If the CPE does not achieve Showtime after this check that the CPE being connected is compatible with the chipset installed in the emutel Maestro If the CPE still does not achieve Showtime then try the other port If this fails try another CPE or another RJ11 lead In the event that the Configuration Softw
22. ven versions of Maestro code which are listed within the Appendices section Module Cross Reference table To load new Maestro code select the SYSTEM pull down tab followed by the Upload Maestro Code option Either enter the full file name and path or use the Browse button to select the file for uploading into the emutel IMaestro The default installation directory is C program files arca technologies Emutel maestro Software Firmware CP ognan Fiica Technet copes Lichilero F Ta Upbocat Up cad Progeess Gw IX 20 APPENDIX Once the file has been selected click on the START button Igtoad Marthe Cade In order to start the re programming process please switch the emutel Maestro off and back on again You should now see the six LEDs of Port 1 on the front of the emutel Maestro rotating in sequence You should also see the Upload Progress bar slowly moving across Do not switch the emutel Maestro off Janad Moestie Code Once the above message appears you should click on the Close button and switch the emutel IMaestro off and back on to complete the reprogramming Re connect to the emutel Maestro using the Comms pull down tab and the Connect option Now check that the software has been correctly recognised by the emutel Maestro by using the System pull down tab and the Configuration option Finally perform a System Reset using the System pull down tab and
23. way settings are as shown These can be edited Clicking OK will update the emutel IMaestro IP settings N B In order for the settings to take effect it is necessary to switch the emutel IMaestro off then on again Go to the Comms Menu and select Disconnect to end the serial communication between the emutel Maestro and your PC With the emutel Maestro s IP settings fully configured you must change the communication settings for the applications to communicate with the emutel IMaestro via the Ethernet port Select Settings from the Comms Menu CHAPTER 2 14 Using the Configuration Software CONFIGURATION SOFTWARE File Edit View Comms System Help Settings Connect Disconnect emutel The Communications Settings Dialog will appear Select Ethernet as the port used by clicking the Ethernet radio button Communicabons Sathage Enter the IP address of the emutel IMaestro Clicking OK will confirm the new configuration settings These settings will be saved when the application is terminated Finally go to the Comms drop down menu and this time select Connect Your PC will then attempt to communicate with the emutel IMaestro via the Ethernet connection and the configuration settings will be read from the unit For further details on using the emutel IMaestro software please refer to the on line help file You can select this from the Emutel Maestro program group or via the Help men
24. y 7 MN BARage hb tele Amiin 1 7 foe z Dohenge Type Feat mA The cdg F Lose O Fanaa 1 EFR Baw r LERE H i a nn Marami Rate thes 0 Hare Magn Upitiogs i Mawn Be ss Ktoni RS Fail Uvntead mi Intense Dalag zus kterkenng Lanao fine 1915 7 bbl Domikesa Be Sating Membina aragian D kimaan 12072 tofo R5 Fant Ovateed EEE Imeiatergreie 55 S Hetkwtatnesn tie 195 CHAPTER 2 11 Connecting via serial port CONFIGURATION SOFTWARE Ensure that the emutel IMaestro is connected to your PC via RS232 connection Click on the Comms drop down menu and select Settings Emutel Maestro Software Settings Disconnect The Communications Settings Dialog will appear Select COM port as the Port used by clicking the radio button and ensure that the baud rate stop bits parity and data bits are as shown below Communications Settings Choose the COM port on your PC that the emutel IMaestro is connected to Click OK to confirm these settings These settings take effect immediately and will be saved when the Configuration Software is closed Therefore it is only necessary to configure the settings once and the above steps are not necessary for subsequent connection attempts CHAPTER 2 12 Connecting via Ethernet CONFIGURATION SOFTWARE Finally go to the Comms drop down menu and this time select Connect Your PC will then attempt to communicate with the emutel Mae
Download Pdf Manuals
Related Search