T-Lock Call Blocker User Manual
Contents
1. PLEASE READ The date amp time setting is also NOT required This data is automatically updated from the caller id information on incoming calls TIP Do not bother setting the date amp time on this device It will automatically update with incoming calls If you still wish to set it up after setting the year s last digit in step 4 press SET again to change the Month MM use dial pad to input the correct month then press SET again to change the Day DD use dial pad to input the correct month then press SET again to change the HOUR HH use dial pad to input the correct month and then press SET again to change the Minutes MM Then hang up the handset and wait 15 seconds to exit programming mode 2 0 Setting the LCD Display Brightness Levels The factory default settings for the display brightness is 2 To adjust it follow the steps below Step 1 Press SET button LCD displays Set 1234567 Step 2 Lift off the handset and press 2 using the dial pad LCD displays LCD 2 Step 3 Press UP or DOWN buttons lt or gt to change the LCD levels from 2 to 1 2 3 4 Step 4 When done hang up handset and wait 15 seconds to exit programming mode 3 0 Adding Outgoing dialing Blocked Numbers to the BLACKLIST Please follow the steps below to manually add phone numbers also prefixes or area codes that you wish to block dialing from your phone line IMPORTANT Make sure your T Lock Call Blocker is installed in series with your existin2. Removing Phone Numbers from the BLACKLIST To remove numbers from the BLACKLIST memory up to 1 200 records press the BLACKLIST button then use UP or DOWN buttons lt or gt to browse list Then press the REMOVE button to delete number from list LCD displays DEL To remove entire list press the REMOVE button more than 3 seconds NOTE You will need to input pass code default 0000 followed by the REMOVE button when LCD displays PASS This is a safety feature to prevent deleting the list unintentionally 10 3 Removing Incoming Area codes or Prefixes from BLACKLIST Follow steps 1 amp 2 above then follow these additional steps Step 3 Use UP or DOWN buttons lt or gt to browse list of blocked numbers Step 4 When displaying the number you wish to remove press REMOVE LCD displays DEL Step 5 When done hang up handset and wait 15 seconds to exit programming mode Important The area codes amp prefixes manually added will not show when browsing the BLACKLIST 10 4 Browsing Removing Phone Numbers from the OUT list To remove numbers from the outgoing list of recent phone numbers up to 50 records press the BLACKLIST button then use the UP or DOWN buttons lt or gt to browse list Now you can press the REMOVE button to delete any phone number you wish LCD displays SUCCEED To remove the entire list press the REMOVE button more than 3 seconds 11 0 BLACKLIST Operation The T Lock Call Blocker will
3. automatically disconnect off hook and hang up the call if the calling number is stored in the BLACKLIST Callers will simply hear a disconnect sound The number of rings you hear before a call is disconnected varies depending on how your call blocker is installed If installed in series you may hear no ring or 1 ring If installed in parallel you may hear 1 or 2 rings There may be other factors affecting the number of rings Please consult our website for more details 12 0 LOCK Feature The LOCK feature is turned OFF as a factory default setting You may lift off handset and input 000111 Star Key 1 2 3 45 6 Pound Key to turn ON the LOCK feature and LOCK all functions LCD displays LOCK If your T Lock Call Blocker s LCD displays LOCK then lift off handset and input 123456 to turn OFF the lock function and enable all T Lock Call Blocker s functions 13 0 LCD Display Alerts and Messages The LCD display will show the following messages or alerts The NEW alert indicates that the phone number is new e g recently added to the T Lock Call Blocker s memory The REP alert indicates that the phone number is already in memory The MAIL alert indicates that you have a new voicemail this feature is provided by your phone service provider as part of the Caller ID service The LCD also shows the current date of week SUN MON TUE WED THU FRI SAT 14 0 Programming Notes 1 When using the handset to program
4. pass code to reset back to default 0000 8 0 Browsing Lists 8 1 Browsing Incoming Phone Numbers Press the UP or DOWN buttons lt 4 or gt to view recent incoming call records Your call blocker will store the last 100 calls received The LCD will display the phone number up to 16 digits date and time of each call 8 2 Browsing BLACKLIST Phone Numbers Press the BLACKLIST button then UP or DOWN buttons lt or gt to view the stored numbers Your call blocker will store up to 1 500 numbers The LCD will display the phone number up to 16 digits 8 3 Browsing Outgoing Phone Numbers Press OUT to browse recent outgoing phone numbers dialed from phone s connected to the PHONE socket of the T Lock Call Blocker Press UP or DOWN buttons lt or gt to browse list LCD displays NO CODE when there are no calls Your call blocker will store up to 50 outgoing numbers Each record can display up to 16 digits 9 0 Section renumbered as 8 3 10 0 Removing Numbers from Lists INCOMING OUT and BLACKLIST 10 1 Removing Phone Numbers from INCOMING List To remove numbers from the INCOMING list of recent calls T Lock Call Blocker holds up to 100 records 16 digits each simply use the UP or DOWN buttons lt 4 or gt to browse list Then press the REMOVE button to delete number from list LCD displays DEL To remove entire list of incoming call records press the REMOVE button gently for more than 3 seconds 10 2
5. phone number to BLACKLIST LCD displays SAVE and SUCCEED 3 You may also add numbers manually Please follow the instructions below to add incoming phone numbers to the BLACKLIST Step 1 Press SET button LCD displays Set 1234567 Step 2 Lift off the handset and press 4 LCD displays the first number stored in the BLACKLIST If empty a blinking cursor should be shown as _ indicating input mode Step 3 Input phone number to be added to the incoming BLACKLIST Step 4 Press UP or DOWN buttons lt 4 or P to save LCD displays SUCCEED Repeat steps 2 4 to add up to 1 200 numbers up to 16 digits in length each Step 5 When done hang up handset and wait 15 seconds to exit programming mode TIP The recommended way to build your BLACKLIST is to use options 1 or 2 above If you choose option 3 above you may need to add area code number and also 1 area code number this depends on how the leading 1 is handled by your phone service provider 5 1 Adding Incoming Area Codes or Prefixes to the BLACKLIST Follow the steps below to add incoming phone area codes and prefixes to BLACKLIST Step 1 Press SET button LCD displays Set 1234567 Step 2 Lift off handset and press 5 If your BLACKLIST is empty a blinking cursor should be shown as _ indicating input mode Otherwise the LCD will display the first stored number in the BLACKLIST Step 3 Input the area code or prefix you wish to block example area code 305
6. T Lock Call Blocker User Manual This manual applies to all model CT CID803 Version 2 x N2 with manufacturer date after 13 10 XX Last updated on 4 24 2015 Installation IMPORTANT THIS DEVICE IS POWERED BY YOUR PHONE LINE AND DOES NOT NEED BATTERIES OR AN EXTERNAL POWER SUPPLY Cannect ta phone Comed te line Packing list Your packaging contains the following items 1 T Lock Call Blocker Call Blocker device with J F LCD display 6 buttons SET OUT BLACKLIST oe REMOVE UP amp DOWN lt 4 or P buttons and two RJ 11 sockets TO LINE TO PHONE 1 Telephone cord 1 Wall Desktop bracket 1 User Manual There are 2 ways of installing your T Lock Call Blocker as shown below The T Lock Call Blocker should work well in both settings however we recommend that you test both to find out the best setup for you SERIES INSTALLATION PARALLEL INSTALLATION TO PHONE EMPTY Ge Blocker TO LINE A 2WAY Spiter not incduded i a Getting Started The T Lock Call Blocker is shipped from the factory ready to start working when connected to any FSK DTMF compatible phone line using the LINE socket There is no programming required in order for this device to start blocking calls Once installed simply wait to start receiving calls then use the scrolling UP or DOWN buttons lt 4 or gt to browse the list of recent incoming calls While browsing you may press the BLACKLIST button to ad
7. d unwanted numbers to the BLACKLIST It s that simple IMPORTANT Please make sure your phone line has the Caller ID service active Your T Lock Call Blocker will not work without it If you are not sure contact Programming your T Lock Call Blocker Call Blocker PREPARATION Before you can start programming your T Lock Call Blocker you need to have a telephone handset wired or wireless connected to the PHONE socket on the back of your call blocker as shown in Series installation diagram You will need to use the dial pad on your handset to program your call blocker 1 0 Setting the YEAR PLEASE READ The YEAR setting is NOT required Since this is a line powered device the YEAR will reset when it loses power because its setting is not stored in the non volatile memory TIP Please do not bother setting the year on this device It will work fine with the default value Follow these steps to change the 4th digit on the year e g from 2012 to 2013 Step 1 Press SET button LCD displays Set 1234567 Step 2 Lift off the handset and press 1 using the dial pad LCD displays 2012 and 3rd digit is blinking indicating that it can be changed Step 3 Press SET button again to move from the 3rd to the 4th digit of the year 2012 Step 4 Press UP button lt 4 to change the blinking digit 3 4 5 Step 5 Once the correct digit is displayed hang up handset and wait 15 seconds to exit programming mode 1 1 Setting Date amp Time
8. g phone s in order for the T Lock Call Blocker to block all the outgoing numbers calls Step 1 Press SET button LCD displays Set 1234567 Step 2 Lift off the handset and press 3 LCD displays a blinking cursor mode indicating input Step 3 Input the phone number or area code or prefix you wish to block Step 4 Press UP or DOWN buttons lt 4 or gt to save LCD displays SUCCEED Repeat steps 3 4 to continue inputting number s you wish to block Step 5 When done hang up handset and wait 15 seconds to exit programming mode 3 1 Browsing Removing Outgoing dialing out Blocked numbers from the BLACKLIST To remove a number from the blocked list you need to press SET press 3 use the UP amp DOWN buttons lt 4 or gt to browse the list of blocked numbers you wish to remove and then press the REMOVE button to remove the number displayed LCD displays DEL and SUCCESS 4 0 Renumbered as 5 0 5 0 Adding Phone Numbers to the BLACKLIST e g Blocking Unwanted Phone Numbers There are 3 ways of adding unwanted phone numbers to the BLACKLIST 1 When an unwanted call is ringing simply press the BLACKLIST button before answering it to disconnect the call and add the number to the BLACKLIST 2 After receiving an unwanted call At a later time you can use the scroll UP DOWN buttons lt or P to browse the list of recent incoming calls see 8 1 then press the BLACKLIST button to add the unwanted
9. prefix 305 558 using the dial pad on your telephone handset Step 4 Press UP or DOWN buttons lt d or P to save number LCD displays SAVE and SUCCEED Repeat steps 2 amp 3 to add up to 10 sets up to 10 digits in length each Step 5 When done hang up handset and wait 15 seconds to exit programming mode 6 0 Turn ON OFF feature to Block all Incoming Calls with no Caller ID Info This feature is disabled OFF as a factory default setting Please follow the steps below if you wish to turn this feature ON and block all calls with no caller ID information Step 1 Press SET button LCD displays Set 1234567 Step 2 Lift off the handset and press 6 LCD displays OFF Step 3 Press UP or DOWN buttons lt or gt to toggle feature ON and OFF Step 4 When ON is shown hang up handset and wait 15 seconds to exit 7 0 Changing the Pass Code The T Lock Call Blocker s factory default pass code is 0000 Follow steps below to change it Step 1 Press SET button LCD displays Set 1234567 Step 2 Lift off the handset and press 7 LCD display INPUT Step 3 Input old pass code default 0000 and press SET LCD displays N PASS Step 4 Input the new pass code up to 4 digits press SET button Step 5 Re enter new pass code and press SET to save it LCD displays SUCCEED Step 6 Hang up handset and wait 15 seconds to allow T Lock Call Blocker to exit programming mode Note You may use 8289 if you forget your
10. your T Lock Call Blocker please disregard the voice messages or any audible line errors you may hear on your telephone line 2 In input mode you may press the OUT button anytime to correct numbers 3 When removing a number the LCD may show a blinking cursor _ That s normal 4 This device uses a technology called EEPROM that allows it to retain all the programming and stored numbers even when disconnected from the phone line VISIT HTTP HQTELECOM COM FOR THE LATEST MANUAL FAQS HOW TO VIDEOS amp SUPPORT
Download Pdf Manuals
Related Search