Chief WM230AUS mounting kit
Contents
1. Figure 35 Installation Instructions 210 220 230 2405 5 Adjustments 2 Bracket Width Adjustment 3 1 Loosen two flat head cap screws wall bracket See Figure 36 2 Slide wall brackets to corresponding width of studs See 4 Figure 36 3 Tighten two flat head cap screws on wall bracket See 5 Figure 36 Loosen two bolts on either side of pitch adjustment screw See Figure 38 Adjust pitch adjustment screw until mount is at desired pitch level Turn clockwise to raise mounting level or turn counterclockwise to lower mounting level See Figure 38 Tighten two bolts on either side of pitch adjustment screw See Figure 38 Tighten two 1 4 20 x 5 8 screws E on underside of mounting bracket See Figure 37 6 Figure 36 Pitch Adjustment Figure 38 Return outer covers to the mount following instructions in Installing Mount Covers section IMPORTANT The mount covers need to be removed Extension Adjustment before proceeding with pitch adjustment 1 NOTE Remove mount covers from the mount following instructions in Removing Mount Covers section 1 Loosen two 1 4 20 x 5 8 hex head cap screws on underside of mounting bracket See Figure 37 Loosen two bol2. Installation Instructions Mount Covers 1 Remove two 8 32 x 1 2 Phillips pan machine screws F holding mount covers on projector arm See Figure 71 2 Install two 8 32 x 1 2 button head security screws V into holes on mount cover See Figure 71 Figure 71 Stop Bracket 1 Remove two bolts holding stop bracket in place on underside of short throw projector mount See Figure 72 26 Stop bracket 2 Figure 72 Install two 1 4 20 x 1 2 button head security screws T through holes in stop bracket and into holes in sliding nuts See Figure 73 Sliding nuts locations bracket Figure 73 Installation Instructions 210 220 230 2405 5 Adapter Plate Bolts 1 Remove projector from short throw projector mount according to projector interface instructions NOTE For most projectors it will be necessary to remove projector prior to installing four security screws to projector bracket For ease of installation it is recommended to remove projector prior to performing the following steps WARNING It is important to replace adapter plate bolts ONE AT A TIME or adapter plate could fall from mount during installation 2 Remove of four bolts from adapter plate See Figure 74 Adapter plate x 4 one at a time Figure 74 3 Install one 1 4 20 x 3 4 button head security screw U into hole vacated by
3. mount 2 1 Upper cover AK 1 Lower cover WM2XXS Interactive Models Onl X 1 4 Cover top Y Interactive cover Semier ud J Quick Start Guide AA 4 8 32 x 3 8 2 1 security AB 4 5 32 8 32 x 3 8 security 1 Stylus 4 1 Hee ee Interactive replacement software tips aa s a 227 1 AG 1 Interactive Stylus USB cable wrist strap ee kit oftware Guide All Models d D 2 wall bracket wall bracket top cap bottom cap e G 4 2 F 10 2 14 2058 1 4 20 x 3 8 4 1 4 20 x 1 1 2 e M 6 J K 4 L 4 5 16 10 24 x 1 3 8 koncrete 5 16 x 2 1 2 anchor e e R 1 5 4 N 4 P 4 Q 4 3 16 10 24 3 8 1 4 20 1 3 4 174 20 1 4 A e e re U 4 Ge 5 32 1 4 20 x 1 2 144 20 x 3 4 security security security 8 32 x 1 2 security 210 220 230 2405 5 Installation Instructions SITE REQUIREMENTS WM2XXS WM2XXS Models Steel Stud Structure WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT The figure below identifies the minimum requirements for installation of display mounts onto a steel stud structure If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attemptin
4. 2000 Server 2003 Vista or 7 30 MB available hard drive space Available USB port e System Power PC Intel 1 42 GHz processor and 1G RAM Mac OS X 10 5 through 10 6 25 MB available hard drive space Available USB port Active Capture Area Size maximum active capture area supported is 4 ft x 7 ft or up to 94 inches diagonal measure e The minimum active capture area supported is 1 7 ft x 1 1 ft Connection Requirement The interactive mount includes a USB cable Screen Recording Requirements Currently available only on Windows platform Pentium IV processor e 1 4GHz with 512MB RAM Environmental Interference Guide Ultrasound Reflections General proximity guideline A distance of 12 feet approximately 4 meters between the motion sensor and the eBeam receiver will normally allow good performance with the maximum board size See Figure 2 Interference can be reduced by reducing the size of the projection area Motion sensor OK Motion Sensor Free Zone _ 12 feet PL Motion sensor Drawing surface Figure 2 Installation Instructions WM210 220 230 240S SI WM2XXS Placement and Projection Area Constraints See Figure 3 e There should be a minimum distance of 12 inches between the base of the dual mount and the top of the projection image e The distance between the base of the dual mount and the botto
5. Figure 53 3 Remove lower cover from mount See Figure 54 Figure 52 Figure 54 21 210 220 230 2405 5 Installation Instructions 4 Remove cable management covers if necessary from short throw projector arm See Figure 55 Cable management covers bottom view Figure 55 NOTE Cables may be routed from below and up wall bracket 5 channel or from above and down behind and into wall mount e Routing Cables from Below Steps 5 6 Open cable clips along bottom edge of wall bracket See Figure 56 cable clips 6 22 Figure 56 Thread cable up wall bracket channel and into opened cable clips See Figure 57 Proceed to Step 8 Figure 57 e Routing Cables from Above Step 7 7 Thread cables down through a surface mount cable accessory not included then behind and into the wall bracket See Figure 58 Proceed to Step 8 view from front Cables Surface Mount Cable Accessory not included Cables Figure 58 Installation Instructions 210 220 230 2405 5 8 Route cables through cover mount projector arm tunnel and into projector See Figure 59 Cables example Figure 59 9 Optional Cables can tied to inside of mount s front cover using cable ties not included Route cables near front
6. Laboratories can be used to mount projector WARNING ELECTRICAL SHOCK HAZARD CUTTING OR DRILLING INTO ELECTRICAL CORDS OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surface is free of electrical wires and cables before cutting drilling or installing fasteners WARNING EXPLOSION AND FIRE HAZARD CUTTING OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surface is free of gas water waste or any other plumbing before cutting drilling or installing fasteners Mounting Wall Bracket Concrete or Concrete Block 1 2 Determine mounting location on wall Using wall bracket B as a template mark four holes at the holes in bracket See Figure 4 Drill four 3 8 holes at marked locations in wall See Figure 4 front view 2 Figure 4 Install four concrete anchors into drilled holes See Figure 5 Install four 5 16 x 2 1 2 hex head lag screws L through four 5 16 washers M outer holes of wall bracket B and into concrete anchors See Figure 5 Figure 5 Wood Studs WARNING The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm Do not install drywall anchors into the seam between
7. equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the short throw projector mounts up to and including the projector does not exceed 50 Ibs 22 68 kg for the WM210S SI or WM220S SI or 25 lbs 11 34 kg for the WM230S SI or WM240S SI e Theweight capacity of the short throw projector mounts may be LIMITED to the lowest weight capacity of any other component located between the short throw wall mount and the projector Rei Ee 2 Important Warnings and Cautions 2 Table of Contents 2 DIMENSIONS ernst s e e 3 Legend RER 4 A en S 5 Site Requirements WM2XXSI and WM2XXS Models Steel Stud Structure 6 WS2XXSI Interactive Mount Only 7 ASSEMBLY AND INSTALLA
8. 1 WM210 220 230 240S SI Installation Instructions 4 Loosen two bolts on either side of pitch adjustment screw NOTE Determine hole configuration to use for each specific See Figure 16 projector mount See Figure 17 5 Adjust pitch adjustment screw until mount is at desired pitch level Turn clockwise to raise mounting level or turn RPM Installation counterclockwise to lower mounting level See Figure 16 1 Line up mounting holes on RPM mount with corresponding ject unting plate See Figure 17 6 Tighten two bolts on either side of pitch adjustment screw 9 See Figure 16 2 Install four 1 4 20 x 1 1 2 Phillips pan machine screws through RPM holes and into projector mounting plate See Figure 18 raise lower Mounting plate RPM 1 Figure 18 Figure 16 3 Install interface and projector to RPM according to RPM 7 Tighten two bolts installed in Step See Figure 15 installation instructions Projector Installation RSM not evaluated and tested by Underwriters Laboratories Installation 1 Line up mounting holes on RSM mount with corresponding holes on projector mounting plate See Figure 17 WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the short throw projecto
9. 1 Loosen two bolts holding stop bracket in place on underside of short throw projector mount See Figure 67 2 Adjust mount to desired extension length See Figure 67 3 Tighten two bolts holding stop bracket to secure mount in desired position See Figure 67 Installation Instructions 210 220 230 2405 5 bottom view Figure 67 Lateral Shift Adjustment IMPORTANT The mount covers need to be removed before proceeding with lateral shift adjustment NOTE Remove mount covers from the mount following instructions in Removing Mount Covers section 1 Loosen two 1 4 20 x 5 8 hex head cap screws on underside of mounting bracket See Figure 68 2 Adjust projector arm laterally to desired position See Figure 68 3 Tighten two 1 4 20 x 5 8 hex head cap screws E loosened in Step 1 See Figure 68 Figure 68 4 Return outer covers to the mount following instructions in Installing Mount Covers section Security Screw Installation Optional Wall Bracket Covers 1 Remove eight 8 32 x 1 2 Phillips pan machine screws from wall bracket covers See Figure 69 Projector arm not shown for display purposes Figure 69 2 Install eight 8 32 x 1 2 button head security screws V into holes in wall bracket covers See Figure Projector arm not shown for display purposes Figure 70 25 210 220 230 2405 5
10. INSTALLATION INSTRUCTIONS eX 2 Dual Stud Short Throw Wall Mounts WM210 220 230 240S S Our Mounts Your Vision 210 220 230 2405 5 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions TABLE OF CONTENTS WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to
11. NS INCHES 24051 45 5 MIN 23051 34 11 MIN 22051 22 11 MIN 21051 15 86 MIN a 23051 TRAVEL 29 5 22051 TRAVEL 17 5 30 25 70 40 MAX 59 58 MAX 35 58 MAX 23 08 MAX IA 54 5 CABLE CHANEL SIONS THRU ARN I 0147 24175 LIS GT e LEVELING ADJUSTMENT WM2xXXSI Interactive Model 1918 um 1 11 i S 2 1 41141 1 ie 1 10 41 DIMENSIONS MILLIMETERS INCHES 210 220 230 2405 5 Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver D
12. TION WM2XXSI and WM2XXS MOUNT MODELS 9 Mounting Wall Bracket 9 Installation to Wall Bracket 11 Projector Installation 12 WM2XXSI INTERACTIVE MOUNT 13 Installing Mount Covers 13 Cable Management Optional 14 Removing Mount Covers 14 Installation of Wall Bracket Covers 16 Adjustments 17 Security Screw Installation Optional 18 WM2XXS STANDARD MOUNT 21 Installing Mount Covers 21 Cable Management Optional 21 Removing Mount Covers 21 Installation of Wall Bracket Covers 23 Adjustments 24 Security Screw Installation Optional 25 Installation Instructions WM210 220 230 240S SI DIMENSIONS 2405 45 5 MIN 70 40 MAX 2305 34 11 MIN 59 58 MAX 2205 22 11 MIN 35 58 2105 15 86 MIN 23 08 MAX TRAVEL GT 2 2205 TRAVEL 17 5 210 TRAVEL III IA 2305 TRAVEL 29 5 54 5 2025 1009 SO LEVELING ADJUSTMENT DIMENSIONS TRAU ARM WM2XXS Standard Model 16 00 l 11 53 DIMENSIO
13. cover and wrap cable tie through slots on front cover and around cables See Figure 60 Route through slots and around cables Figure 60 10 Replace removed cable management covers if necessary Insert one side of cover into groove and press firmly on the cover on the other side until it snaps into the other groove See Figure 61 Figure 61 11 Return outer covers to the mount following instructions in Installing Mount Covers section Installation of Wall Bracket Covers NOTE If security screws are going to be used use the security screws V to install wall bracket covers See Security Screw Installation section for details 1 Place wall bracket top caps over top of each wall bracket arm See Figure 62 Projector arm not shown for display purposes Figure 62 2 Secure wall bracket top caps C to wall bracket arms by installing four 8 32 x 1 2 Phillips pan machine screws F through holes in covers and wall bracket See Figure 63 3 Place wall bracket bottom caps D over bottom of each wall bracket arm See Figure 62 23 210 220 230 2405 5 Installation Instructions 4 Secure wall bracket bottom caps D to wall bracket arms by installing four 8 32 x 1 2 Phillips pan machine screws F through holes in covers and wall bracket See Figure 63 Projector arm not shown for display purposes Fi
14. ded Route cables near front cover and wrap cable tie through slots on front cover and around cables See Figure 32 D LE tie not included D D Route through slots around cables Figure 32 11 Replace removed cable management covers if necessary Insert one side of cover into groove and press firmly on the cover on the other side until it snaps into the other groove See Figure 33 Figure 33 12 Return outer covers to the mount following instructions in Installing Mount Covers section 16 Installation of Wall Bracket Covers NOTE If security screws are going to be used use the security screws V to install wall bracket covers See Security Screw Installation section for details 1 Place wall bracket top caps over top of each wall bracket arm See Figure 34 Projector arm not shown for display purposes Figure 34 2 Secure wall bracket top caps C to wall bracket arms by installing four 8 32 x 1 2 Phillips pan machine screws F through holes in covers and wall bracket See Figure 35 3 Place wall bracket bottom caps D over bottom of each wall bracket arm See Figure 34 4 Secure wall bracket bottom caps D to wall bracket arms by installing four 8 32 x 1 2 Phillips pan machine screws F through holes in covers and wall bracket See Figure 35 Projector arm not shown for display purposes
15. drywall pieces Determine mounting location on wall Use a stud finder to locate 2 x 4 wood studs For studs less than 16 apart mounting brackets will have to be adjusted See appropriate Adjustments section for details Line up inner four holes on wall bracket B with center of studs at desired mounting location See Figure 6 Using wall bracket B as a template mark four holes at the holes in bracket See Figure 6 Drill four 7 32 holes at marked locations in wall See Figure 6 front view Wood studs D oO Figure 6 210 220 230 2405 5 Installation Instructions 5 Install four 5 16 x 2 1 2 hex head lag screws L through four 5 16 washers M holes of wall bracket and into drilled holes See Figure 7 Figure 7 Steel Studs IMPORTANT See Site Requirements section before proceeding with Steel Studs installation to ensure installation site meets requirements The drywall must have a minimum thickness of 1 2 1 Determine mounting location on wall Use stud finder to locate steel studs For studs less than 16 apart wall bracket will have to be adjusted See appropriate Adjustments section for details 2 Line up four holes on wall bracket with center of studs at desired moun
16. e 25 2 Raise and remove the upper cover from the mount See Figure 25 Figure 26 Remove the lower cover from the wall mount See Figure 26 Remove cable management covers if necessary from short throw projector arm See Figure 27 bottom view Cable management covers Figure 25 14 Figure 27 Installation Instructions WM210 220 230 240S SI NOTE Cables may be routed from below and up wall bracket channel or from above and down behind and into wall mount e Routing Cables from Below Steps 6 and 7 Open cable clips along bottom edge of wall bracket See Figure 28 7 Figure 28 Thread cable up wall bracket channel and into opened cable clips See Figure 29 Proceed to Step 9 8 Figure 29 e Routing Cables from Above Step 8 Thread cables down through a surface mount cable accessory not included then behind and into the wall bracket See Figure 30 Proceed to Step 9 view from front Cables Surface Mount not included Cables Cable Accessory view from back Figure 30 9 Route cables through cover mount projector arm tunnel and into projector See Figure 31 Cables example Figure 31 15 210 220 230 2405 5 Installation Instructions 10 Optional Cables can be tied to inside of mount s front cover using cable ties not inclu
17. estornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a m o A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option d y 4 d 2 Hex Head Wrench Llave de cabeza hexagonal Sechskantschllssel Chave de sextavada Chiave esagonale Zeskantsleutel Cl a t te hexagonale 9 9 Security Wrench Llave de seguridad Sicherheitsschlissel Chave de seguran a Chiave di sicurezza Veiligheidssleutel Cl de s curit Installation Instructions 210 220 230 2405 5 TOOLS REQUIRED FOR INSTALLATION 707 3 16 included 5 32 included 52 71 security 5 32 6 long included 1 La 2 an 1 2 12 7mm ec security PARTS All Models WM2XXS Models Only A 1 g Short throw
18. g the following steps WARNING It is important to replace adapter plate bolts ONE AT A TIME or adapter plate could fall from mount during installation 2 Remove one of four bolts from adapter plate See Figure 49 20 Adapter plate x 4 one at a time Figure 49 Install one 1 4 20 x 3 4 button head security screw U into hole vacated by removed bolt in previous step and into plastic spacer See Figure 50 Repeat Steps 2 3 for remaining three bolts one bolt at a time U x 4 one at a time Figure 50 Reinstall projector according to interface instructions Installation Instructions WM210 220 230 240S SI WM2XXS STANDARD MOUNT Cable Management Optional Installing Mount Covers In most cases cable management covers will NOT need to be removed in order to route cables from projector to the wall 1 Raise the lower cover AK to wall mount and hold in place mount But for some thick cables removing the covers may be See Figure 51 necessary Removing Mount Covers 1 Remove and save two 8 32 x 1 2 Phillips pan head screws from upper cover See Figure 53 2 Raise upper cover away from the mount See Figure 53 Figure 51 2 Lower the upper cover AJ onto the wall mount and fasten through upper cover lower cover AK and into wall mount with two 8 32 x 1 2 Phillips pan head screws F See Figure 52
19. g installation It should also be noted that no other equipment should be mounted to the same stud See Figure 1 16 or 24 on center Studs Display Mount Installation Location Must be centered on stud A If back side of wall is unfinished drywall must be installed to a minimum of one stud left and right of the stud s being used to install the mount Drywall must be secured to studs with screws 12 on center There must be a minimum of 1 7 8 48mm clearance inside wall Drywall 1 2 minimum Drywall Thickness _ Both Sides of Stud See hazard statement on page 2 Steel Stud 2 x 4 25ga minimum Stud type and structural strength must conform to the North American Specification for the Design of Cold Formed Steel Structural Members 362 125 18 C Shape S Stud Section Figure 1 210 220 230 2405 5 Installation Instructions WS2XXSI INTERACTIVE MODEL ONLY The Chief Interactive Mount WM2XXS works with standard projectors and Windows and Macintosh computers The Interactive Mount will transform existing whiteboards or other hard flat surfaces into interactive whiteboards and allows users to present annotate and interact with their projected content and all of their desktop applications Minimum System Requirements e Windows System Compatible PC with Pentium 400 MHz processor and 256 MB RAM Windows
20. gure 63 Adjustments Bracket Width Adjustment 1 Loosen two flat head cap screws wall bracket See Figure 64 2 Slide wall brackets to corresponding width of studs See Figure 64 3 Tighten two flat head cap screws wall bracket See Figure 64 QD gt lt Figure 64 Pitch Adjustment IMPORTANT The mount covers need to be removed before proceeding with pitch adjustment NOTE Remove mount covers from the mount following instructions in Removing Mount Covers section 24 1 Loosen two 1 4 20 x 5 8 hex head cap screws E on underside of mounting bracket See Figure 65 2 2 24 bottom view Figure 65 2 Loosen two bolts on either side of pitch adjustment screw See Figure 66 3 Adjust pitch adjustment screw until mount is at desired pitch level Turn clockwise to raise mounting level or turn counterclockwise to lower mounting level See Figure 66 4 Tighten two bolts on either side of pitch adjustment screw See Figure 66 5 Tighten two 1 4 20 x 5 8 screws E on underside of mounting bracket See Figure 65 Figure 66 6 Return outer covers to the mount following instructions in Installing Mount Covers section Extension Adjustment
21. jector to RSA according to RSA installation instructions IMPORTANT Complete the installation by proceeding to WM2XXSI Interactive Mount section or WM2XXS Standard Mount section as appropriate WM2XXS I INTERACTIVE MOUNT Installing Mount Covers 1 Route cables from projector through cartridge in interactive cover Y See Figure 22 Route cables Figure 22 2 Connect USB cable AH to cartridge through bottom of lower cover 3 Raise the lower cover containing cartridge and attach to wall mount using two 8 32 x 3 8 Phillips pan head screws AB See Figure 23 Figure 23 13 210 220 230 2405 5 Installation Instructions 4 Lower the upper cover X onto the wall mount and lower cover and fasten with two 8 32 x 3 8 Phillips pan head screws AB See Figure 24 NOTE Be sure cables and cords are not pinched between upper and lower covers Remove and save two 8 32 x 3 8 Phillips pan head screws AB from lower cover See Figure 26 Figure 24 Cable Management Optional In most cases cable management covers will NOT need to be removed in order to route cables from projector to the wall mount But for some thick cables removing the covers may be necessary Removing Mount Covers 1 Remove and save two 8 32 x 3 8 Phillips pan head screws AB from upper cover See Figur
22. m corner of the projection image both right and left should be less than or equal to 110 inches s The projection image should start a minimum of 1 inch from the base of the top frame of the whiteboard projection image should be positioned within the fan area extending from the Chief Interactive Dual Mount This fan area should not exceed 140 degrees Whiteboard Constraints whiteboard should not be thicker than 1 See Figure 3 The ledge of the whiteboard frame should be less than or equal to 1 3 See Figure 3 Important Notes Donotput sticky notes hanging paper cables outlets or other items below the wall mount or inside the capture area See Figure 3 Image should be placed one inch below the edge of the whiteboard to minimize interference from the frame top Minimum 12 inches from base of mount lt 1 3 to projection Whiteboard S lt ledge 21 Capture area Projected areas Projection gt lt 1 Whiteboard side view Figure 3 Installation Instructions WM210 220 230 240S SI ASSEMBLY AND INSTALLATION WM2XXSI and WM2XXS MODELS WM 210S SI 2205 5 2305 5 240S SI short throw p rojector mounts can be mounted to concrete concrete block wood studs or steel studs They can be mounted to 2 x 4 wood studs up to 16 apart For studs more than 16 apart the WMAL24 accessory not evaluated and tested by Underwriters
23. r mounts 2 Install four 10 24 x 1 3 8 Phillips pan machine screws J up to and including the projector does not exceed 50 Ibs FUE Ign holes and into projector mounting plate See igure 22 68 kg for the WM210S SI or the WM220S S or 25 Ibs 11 34 kg for the WM230S S or 2405 5 NOTE RPM RPA and RSA are sold separately H bottom view Figure 19 3 Install interface and projector to RSM according to RSM Figure 17 installation instructions 12 Installation Instructions 210 220 230 2405 5 RPA Installation 1 Line up mounting holes on RPA mount with corresponding holes on projector mounting plate See Figure 17 2 Install four 1 4 20 x 3 8 Phillips pan machine screws G through RPA holes and into projector mounting plate See Figure 20 d o 5 Mounting plate RPA Figure 20 3 Install interface and projector to RPA according to RPA installation instructions RSA Installation 1 Line up mounting holes on RSA mount with corresponding holes on projector mounting plate See Figure 17 2 Install four 10 24 x 3 8 Phillips pan machine screws S through RSA holes and into projector mounting plate See Figure 21 Mounting plate RSA GIE ER Figure 21 3 Install interface and pro
24. removed bolt in previous step and into plastic spacer See Figure 75 4 Repeat Steps 2 3 for remaining three bolts one bolt at a time Adapter wee Plastic U x 4 one at a time Figure 75 Reinstall projector according to interface instructions 27 210 220 230 2405 5 Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8802 002082 Rev02 2011 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 07 11 USA International Europe Asia Pacific gt TU 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 SCH d
25. ructions 210 220 230 2405 5 10 Place wall bracket over anchors and align mounting holes in display mount with holes in anchors See Figure 12 11 Insert 1 4 20 x 1 3 4 Phillips head screws N through 1 4 washer Q corresponding mounting hole on wall bracket and into anchor P and tighten until flush against mount DO NOT overtighten See Figure 12 12 Repeat Step 11 for remaining 3 mounting holes WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPM ENT Overtightening of mounting hardware can damage the steel studs DO NOT overtighten mounting hardware Steel stud Drywall Q x4 N x 4 OW _ Anchor metal channel side view Figure 12 Installation to Wall Bracket 1 Lift short throw projector arm A up to wall bracket and hook top plate onto cross bracket Figure 13 on wall bracket See Figure 13 Slide lower plate onto cross bracket on mounting bracket See Figure 14 Figure 14 Install two 1 4 20 x 5 8 hex head bolts E through holes on short throw projector arm A and into sliding nuts on mounting bracket B DO NOT TIGHTEN SCREWS AT THIS POINT See Figure 15 3 AA x2 Figure 15 1
26. ting location See Figure 8 3 Using wall bracket as a template mark four holes at the inner four holes in bracket See Figure 8 4 Drill four 1 2 holes at marked locations in wall See Figure 8 front view Steel studs J B 1 CJ SH x4 JOR Figure 8 10 5 Hold metal channel on anchor flat alongside plastic straps and slide channel through hole See Figure 9 Drywall Plastic 9 6 Holding plastic straps on anchor pull anchor away from wall until channel rests flush behind wall making sure anchor channel is positioned vertically on stud See Figure 10 7 Slide plastic cap on anchor P towards wall until flange of cap is flush with wall See Figure 10 Steel stud Drywall Plastic cap Anchor metal channel side view Figure 10 8 Snap off plastic straps on anchor at wall by pushing side to side snapping off straps level with flange of plastic cap See Figure 11 9 Repeat Steps 6 through 8 for each mounting hole Steel stud 7 1 d Plastic straps metal channel side view Figure 11 Installation Inst
27. ts holding stop bracket in place on underside of short throw projector mount See Figure 39 Adjust mount to desired extension length See Figure 39 Tighten two bolts holding stop bracket to secure mount in desired position See Figure 39 bottom view bottom view Figure 39 17 210 220 230 2405 5 Installation Instructions Lateral Shift Adjustment IMPORTANT The mount covers need to be removed before proceeding with lateral shift adjustment NOTE Remove mount covers from the mount following instructions in Removing Mount Covers section 1 Loosen two 1 4 20 x 5 8 hex head cap screws on underside of mounting bracket See Figure 40 2 Adjust projector arm laterally to desired position See Figure 40 3 Tighten two 1 4 20 x 5 8 hex head cap screws loosened in Step 1 See Figure 40 Figure 40 4 Return outer covers to the mount following instructions in Installing Mount Covers section Security Screw Installation Optional Wall Bracket Covers 1 Remove eight 8 32 x 1 2 Phillips pan machine screws from wall bracket covers See Figure 41 Projector arm not shown for display purposes Figure 41 18 2 Install eight 8 32 x 1 2 button head security screws V into holes in wall bracket covers See Figure 42 Projector arm not shown for display purposes Figure 42 Mo
28. unt Covers 1 Remove two 8 32 x 3 8 Phillips pan head screws AB from upper cover See Figure 43 2 Raise and remove the upper cover from the mount See Figure 43 Upper cover Figure 43 Installation Instructions 210 220 230 2405 5 3 Remove two 8 32 x 3 8 Phillips head screws AB from lower cover See Figure 44 Figure 44 4 Install two 8 32 x 3 8 button head security screws AA into lower cover See Figure 45 Figure 45 5 Replace upper cover and install two 8 32 x 3 8 button head security screws AA into upper cover See Figure 46 Figure 46 Stop Bracket 1 Remove two bolts holding stop bracket in place on underside of short throw projector mount See Figure 47 Stop bracket Figure 47 19 210 220 230 2405 5 Installation Instructions 2 Install two 1 4 20 x 1 2 button head security screws through holes in stop bracket and into holes in sliding nuts See Figure 48 Sliding nuts locations bracket Figure 48 Adapter Plate Bolts 1 Remove projector from short throw projector mount according to projector interface instructions NOTE For most projectors it will be necessary to remove projector prior to installing four security screws to projector bracket For ease of installation it is recommended to remove projector prior to performin
Download Pdf Manuals
Related Search