NextBolt NX4 Secure Mount Manual
Contents
1. Actuator Systems Australia http www advancedactuators com au e Fully open the sliding cover located on the outdoor unit immediately e Sensor will flicker for less than one second e A Single short beep will be heard and the fingerprint sensor will power on e Rest an Administrator s fingerprint on the scanning window e When the LED light goes out enter the keypress sequence The chart is in Appendix A of this manual o If you hear four beeps this indicates that the Administrator was not recognized If you hear five beeps this indicates the user deletion was not successful Begin again from the first step of Section III When one long beep is hear the user has been deleted successfully Once the deletion is successful you are not required to verify the administrator to remove additional users Simply enter the next user 37 NextBolt User Manual For support contact us at support advancedactuators com au Actuator W Systems Australia http www advancedactuators com au ID sequence and wait for the long beep for each user you wish to remove Close the sliding cover to end the deletion procedure e Close the sliding cover e Repeat steps from the beginning of Section III to delete the next most recently enrolled fingerprint user Section IV Deleting ALL Fingerprint Users Sliding cover must be closed before any programming sequence can begin Deleting ALL enrolled fingerprint users will reset t2. ADD button located on the indoor unit e Single beep will be heard e Fully open the sliding cover located on the outdoor unit immediately e Sensor will flicker for less than one second 31 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au W e A single short beep will be heard and the fingerprint sensor will power on e After the fingerprint sensor powers on rest your pointer finger on the sensor window during the first of three scans e Keep your pointer finger on the scanning window thru all three scans e After the scanning is completed you will hear one of the following o Single long beep indicating that the operation was successful OR o Four beeps indicating that your fingerprint was not successfully enrolled If you hear four beeps please start the enrollment process over from the beginning e Close the sliding cover USER 2 through USER 99 32 NextBolt User Manual For support contact us at support advancedactuators com au Actuator W Systems Australia http www advancedactuators com au Section II Enrolling Fingerprint Users 2 thru 99 Sliding cover must be closed before any programming sequence can begin As noted in the Helpful Hints section the third thru ninety ninth fingerprint users enrolled Users 3 thru 99 are automatically programmed at the USER level USER level fingerp
3. e Fully lift the sliding cover located on the outdoor unit 40 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au e A single short beep will be heard and the fingerprint sensor will power on e After the fingerprint sensor powers on rest any enrolled fingerprint on the sensor window to verify If fingerprint verification is successful the deadbolt will disengage and a single short beep will be heard If verification of enrolled fingerprint was not successful then 4 short beeps will be heard If this happens the fingerprint scanner will still turn on two additional times enabling users to try more If all the two additional verification attempts still fail please start the unlocking process over again from the beginning of this section e Close the sliding cover 4 NextBolt User Manual For support contact us at support advancedactuators com au Actuator W Systems Australia http www advancedactuators com au Section VI Locking the Actuator Systems NextBolt from Outside In case of emergency override keys can be used to engage the deadbolt Please use the following steps to lock the Actuator Systems NextBolt from outside when leaving e Make sure your door is closed e Open and immediately close the sliding cover e Deadbolt will engage and a single short beep will be heard 42 NextBol
4. and closing the sliding cover 8 Try to lock and unlock from inside by pressing the Open Close button to ensure it works well electronically IMPORTANT SECURITY NOTE WITHOUT ANY FINGERPRINTS ENROLLED THE NextBolt WILL LOCK AND UNLOCK BY FULLY OPENING AND FULLY CLOSING THE SLIDING COVER 23 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 5 Trouble Shootin PROBLEMS POSSIBLE SOLUTIONS REASONS Indoor turn knob does 1 Incorrect installation Make sure the tail piece was not turn or turns very inserted vertically through the sluggishly cross slot of the deadbolt and slot of the indoor unit while the turn knob was vertical facing down 2 Incorrect tailpiece Measure the door thickness and length swap or trim the tail piece per section 4 3 of the installation manual Bolt does not extend Incorrect 1 Remove the units from fully 18mm instead adjustment the door of 25mm procedure from 2 if the backset tailpiece 60mm to 70mm or slot is not showing in the v v of backset position the backset during installation has been adjusted incorrectly Refer to section 3 2 of the installation manual 24 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia Indoor turn knob turns but nothing happens http www advancedactuators com au The tail piece
5. at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au For instructions on how to adjust the length of the adjustable backset refer to Section 3 2 Adjustment of Deadbolt Backset 1 x Deadbolt Latch 60 70mm backset Screws 82 mm Screws 2x 40 mm amp 1 x 29mm Wooden amp Metal Screws 4 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 2 Required Tools Hand Held Bolt Cutters Philips amp flat head screw drivers La Im 11 Marker 12 file 5 NextBolt User Manual For support contact us at support advancedactuators com au Actuator W Systems Australia http www advancedactuators com au 3 Pre installation 3 1 Mark and bore holes on the door 3 11 Mark holes on door For doors with existing deadbolt lock with 54mm diameter hole 1 Remove existing cylindrical deadbolt 6 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia NextBolt User Manual http www advancedactuators com au 2 Please be sure to use the installation template when installing the Actuator Systems NextBolt on a door with an existing deadbolt 3 Cut out the two 10mm holes on the Installation Template that correspond to your existing backset 60mm or 70mm 4 Rest the installation
6. did not 1 go through the cross slot of the deadbolt Remove and reinstall the outdoor unit Then insert the tail piece through the cross slot of the deadbolt and slot of the indoor unit while the turn knob is in vertical position facing down Tail piece was om trimmed too short and does not penetrate the slot of the indoor unit Contact the Actuator Systems NextBolt dealer that you purchased to lock from OR Contact us at support advancedactuators com au The sliding cover is fully lifted to power on without any fingerprint enrolled inside the deadbolt does not disengage or four alert beeps are heard Right amp left hand door configurations 1s set incorrectly Correctly configure the unit for left or right hand door swing per section 4 5 Uninstall the outdoor unit and keep the UP sign side of the tail piece up and insert the tail vertically through the cross slot of the deadbolt while the turn knob is in vertical position Check the position of the strike The tail piece was not set properly When the sliding cover Improper positioning is fully lifted and immediately put down to engage the deadbolt but the deadbolt does not fully engage or four alert beeps are heard NextBolt User Manual of the strike and strike lining box It may be deflecting the deadbolt 25 and the strike lining box For support contact us at support advancedactuators com au Actuator Systems Austr
7. drawings Light pressure when placing the finger on the scanner gives the best image but the finger must not move during scanning Moist fingers provide better images than dry ones If on cold dry days you have difficulty for example try moistening your finger with your breath or a little lotion Very dry dirty or scarred fingers are obviously not recommended since they will obscure the fingerprint The pointer finger is by far the best fingerprint to enroll The thumb is the second best digit If the pointer finger is difficult to enroll or verify try enrolling the same NON ADMIN fingerprint 2 or 3 times at slightly different angles EX Enroll same pointer finger as users 3 4 and 5 In the event you still have trouble enrolling fingerprints we have included 2 fingerprint pads in your box Moisten your fingers with one of these pads prior to enrollment These dramatically increase the quality of the enrollment Once enrolled these pads may be discarded Always wait until the fingerprint scanner turns on to place your finger on the scanning window This is true for both fingerprint enrollment AND verification 28 NextBolt User Manual For support contact us at support advancedactuators com au Actuator W Systems Australia http www advancedactuators com au When trying to enroll or verify fingerprints in direct sunlight be sure to shade the sensor with your shadow so sunlight will not reflect off of the mirror in the senso
8. result in improper operation of the latch logic and will void the warranty 10 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 4 Installation 4 1 Installation of Deadbolt Insert the deadbolt latch into the hole in the edge of the door follow the UP sign keeping it parallel to the face of the door Mark the outline of the face plate and remove the deadbolt Then chisel 3mm deep rectangular shape per your marking or until the faceplate is flush with the door edge Insert the deadbolt latch make sure the deadbolt UP sign is facing upwards Then fasten the screws 11 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 4 2 Installing Strike and Strike Lining BOX on the door jamb 1 Close the door until the deadbolt touches the door jamb along the face plate to mark the horizontal center lines 2 Measure one half of the door thickness from one side of the door jamb and then mark the vertical center lines 3 Extend the vertical center line and the horizontal line to mark the drill center point for the strike Bore a 25mm diameter and 25mm deep hole in the door jamb at the center point for strike To ensure the proper deadbolt function this hole must be drilled at least 25mm deep Chisel the do
9. template on the front of the door on top of the existing 54mm hole making sure that it is aligned properly for the door s existing 60mm or 70mm backset 7 For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 5 Mark the two 10mm holes that you cut out of the installation template on the door with a magic marker 6 Bore the two 10mm holes into the door using a 10mm drill bit making sure that the holes fully penetrate through the door 7 Go to Section 4 3 in the User Manual For doors that do not have a cylindrical deadbolt lock or a hole for the cylindrical deadbolt lock A Start approximately 1170mm from floor Select the 57 appropriate installation F cylinder hole template according to the length of the backset Fold Latch hole i iE and apply the template to the Trey edge of the door bevel Mark the center point of the cylinder hole on the door face and then mark the center point of the deadbolt hole on door edge as indicated on the template NextBolt User Manual For support contact us at support advancedactuators com au W gol Australia http www advancedactuators com au B For installation of combination set door handle and deadbolt it 1s recommended that the distance is 140mm between the two center points Mark the center points of the two small holes on the door face for the two upper fixing
10. that as much of your finger as possible is in contact with the sensor Do not move your finger while it is being scanned wait until you hear the long beep Keep even pressure applied to the center of the fingerprint pad You can enroll the same finger more than one time It also can help enrollment if the finger you use is not overly dry a On our website www advancedactuators com au we offer inexpensive disposable fingerprint enhancement pads These pads are only necessary in the event you had trouble enrolling To use just wipe your finger with one of the pads 5 seconds before enrollment they are ONLY used for enrollment These pads considerably enhance the quality of the ridges of the fingerprint Thanks again from your friends at Actuator Systems 52 NextBolt User Manual For support contact us at support advancedactuators com au
11. DEL ADD DEL O CB 35 ADD DEL DEL DEL ADD ADD O CB 36 ADD DEL DEL ADD DEL DEL O CB 37 ADD DEL DEL ADD DEL ADD O CB 38 ADD DEL DEL ADD ADD DEL O CB 39 ADD DEL DEL ADD ADD ADD O CB 40 ADD DEL ADD DEL DEL DEL O CB 41 ADD DEL ADD DEL DEL ADD O CB 42 ADD DEL ADD DEL ADD DEL O CB 43 ADD DEL ADD DEL ADD ADD O CB 44 ADD DEL ADD ADD DEL DEL O CB 45 ADD DEL ADD ADD DEL ADD O CB 46 ADD DEL ADD ADD ADD DEL O CB 47 ADD DEL ADD ADD ADD ADD O CB 47 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 48 ADD ADD DEL DEL DEL DEL O CB 49 ADD ADD DEL DEL DEL ADD O CB 50 ADD ADD DEL DEL ADD DEL O CB 51 ADD ADD DEL DEL ADD ADD O CB 5 ADD ADD DEL ADD DEL DEL O CB 53 ADD ADD DEL ADD DEL ADD O CB 54 ADD ADD DEL ADD ADD DEL O CB 55 ADD ADD DEL ADD ADD ADD O CB 56 ADD ADD ADD DEL DEL DEL O CB S ADD ADD ADD DEL DEL ADD O CB 58 ADD ADD ADD DEL ADD DEL O CB 59 ADD ADD ADD DEL ADD ADD O CB 60 ADD ADD ADD ADD DEL DEL O CB 61 ADD ADD ADD ADD DEL ADD O CB 62 ADD ADD ADD ADD ADD DEL O CB 63 ADD ADD ADD ADD ADD ADD O CB 64 ADD DEL DEL DEL DEL DEL DEL O CB 48 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 65 ADD DEL DEL DEL DEL DEL ADD O CB 66 ADD DEL DEL DEL DEL ADD DEL O CB 67 ADD DEL DEL DEL DEL ADD ADD
12. O CB 68 ADD DEL DEL DEL ADD DEL DEL O CB 69 ADD DEL DEL DEL ADD DEL ADD O CB 70 ADD DEL DEL DEL ADD ADD DEL O CB 71 ADD DEL DEL DEL ADD ADD ADD O CB d2 ADD DEL DEL ADD DEL DEL DEL O CB 73 ADD DEL DEL ADD DEL DEL ADD O CB 74 ADD DEL DEL ADD DEL ADD DEL O CB 75 ADD DEL DEL ADD DEL ADD ADD O CB 76 ADD DEL DEL ADD ADD DEL DEL O CB 77 ADD DEL DEL ADD ADD DEL ADD O CB 78 ADD DEL DEL ADD ADD ADD DEL O CB 79 ADD DEL DEL ADD ADD ADD ADD O CB 80 ADD DEL ADD DEL DEL DEL DEL O CB 81 ADD DEL ADD DEL DEL DEL ADD O CB 49 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 82 ADD DEL ADD DEL DEL ADD DEL O CB 83 ADD DEL ADD DEL DEL ADD ADD O CB 84 ADD DEL ADD DEL ADD DEL DEL O CB 85 ADD DEL ADD DEL ADD DEL ADD O CB 86 ADD DEL ADD DEL ADD ADD DEL O CB 87 ADD DEL ADD DEL ADD ADD ADD O CB 88 ADD DEL ADD ADD DEL DEL DEL O CB 89 ADD DEL ADD ADD DEL DEL ADD O CB 90 ADD DEL ADD ADD DEL ADD DEL O CB 91 ADD DEL ADD ADD DEL ADD ADD O CB 92 ADD DEL ADD ADD ADD DEL DEL O CB 93 ADD DEL ADD ADD ADD DEL ADD O CB 94 ADD DEL ADD ADD ADD ADD DEL O CB 95 ADD DEL ADD ADD ADD ADD ADD O CB 96 ADD ADD DEL DEL DEL DEL DEL O CB 97 ADD ADD DEL DEL DEL DEL ADD O CB 98 ADD ADD DEL DEL DEL ADD DEL O CB 50 NextBolt User Manual For support contact us at support advancedactuators com au Actuator W Systems Australia htt
13. alia http www advancedactuators com au When the sliding cover Batteries not inserted 1 Remove amp reinsert the batteries is lifted up during daily correctly following and signs in use nothing happens the battery house fingerprint scanner does not blink Check the connections and 2 Wires not connected make sure wires are fully properly plugged in Six beeps are heard Low Voltage Change the batteries when any function is performed Operation Manual Operation Manual Helpful Hints Please be sure to physically leave your door open until you have successfully enrolled the first user ADMINISTRATOR into the Actuator Systems NextBolt and have successfully verified the new user s fingerprint to unlock the door With no fingerprints enrolled in the Actuator Systems NextBolt the deadbolt will engage disengage when the sliding cover is fully opened and immediately closed Definitions of Indication Beeps 26 NextBolt User Manual For support contact us at support advancedactuators com au Actuator D australia http www advancedactuators com au Single Short Beep Indicates that any operations sequence has begun OR that the door has been successfully locked or unlocked OR that the sliding cover has been left open for more than ten seconds Single Long Beep Indicates that programming operation was successful Short Double Beep Indicates that individual fingerprint user deletion se
14. cc eeeeeeeeeeees 15 4 5 Installation of the Indoor Unit ee eeeeeeeeeeees 17 4 6 Final inspection adjustment prior to enrollment 23 De TROND ESED T EE E E E 24 Operation Minya lerce E EEE E 26 Section I Enrolling Administrators First Fingerprint ES 6g ag ne Pe nen ER Oe re 30 Section II Enrolling Fingerprint Users 2 thru 99 33 Section III Deleting Individual Fingerprint Users 36 Section IV Deleting ALL Fingerprint Users 38 Section V Unlocking the Actuator Systems NextBolt MOM OU SIGS e sect ecetousasdesaueseaaes 40 Section VI Locking the Actuator Systems NextBolt from OD SS a A E E ET 42 Section VII Locking and Unlocking the Actuator Systems NextBolt from Inside eeeeeeeeeeeeeeeeeees 43 SUDDO one eee ee a oe ee re een eee eee 44 ya ea ea alli 9 DO epee ennenen eee rennet nee ann eee oe ee ee ene 45 FINGERPRINT ENROLLMENT CODES eee 45 2 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au Installation Manual 1 Parts Please familiarize yourself with all the parts in the packaging box of the Actuator Systems NextBolt If any part is missing or damaged contact our service center or your local dealer S Indoor Unit Strike Lining Box Outdoor Unit Outdoor Rubber Gasket Strike Plate 3 NextBolt User Manual For support contact us
15. ce can begin As noted in the Helpful Hints section the first two users that enroll their fingerprints into the Actuator Systems NextBolt will automatically be programmed as ADMINISTRATORS Users 1 and 2 ADMINISTRATORS can apply all programming functions as well as verify their fingerprints to unlock the door Please note the methodology for enrolling fingerprints after the first enrolled fingerprint requires pressing the ADD DELETE button s AND the OPEN CLOSE button in sequence as directed by Appendix A henceforth described as the keypress sequence The OPEN CLOSE button when used in conjunction with enrollment procedures serves as a function or enter key and must be pressed after the combination code s or keypress sequence have been entered If not pressed the memory will not accept the User code Please also refer to our training videos for practical demonstrations on enrollment procedures Please also refer to our Knowledge Base for answers to many frequently asked questions You may also download our Quick Reference and Handy Enrollment Table from the Support Section of our website 30 NextBolt User Manual For support contact us at support advancedactuators com au Actuator W Systems Australia http www advancedactuators com au Please use the following steps to enroll the first fingerprint user ADMINISTRATORI USER 1 e Remove the battery cover from the indoor unit e Press the
16. he lock and all users including Administrators fingerprints will be deleted With no fingerprints enrolled in the Actuator Systems NextBolt the deadbolt will engage disengage when the sliding cover is fully opened and immediately closed 38 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au Please use the following steps to delete ALL fingerprint users l Press and hold the DEL button 2 While holding down the DEL button add the other two buttons ADD amp OPEN CLOSE Now all three buttons on the lock will be held down 3 When one long beep is heard pull the outside cover up and place the Admin finger on the sensor for verification when the sensor light turns on 4 Once one long beep is heard the lock is reset successfully e Close the sliding cover IMPORTANT SECURITY NOTE WITHOUT ANY FINGERPRINTS ENROLLED THE NEXTBOLT WILL LOCK AND UNLOCK BY FULLY OPENING AND FULLY CLOSING THE SLIDING COVER 39 NextBolt User Manual For support contact us at support advancedactuators com au Actuator W Systems Australia http www advancedactuators com au Section V Unlocking the Actuator Systems NextBolt from outside In case of emergency override keys can be used to disengage the deadbolt Please use the following steps to unlock the Actuator Systems NextBolt from outside with your enrolled fingerprint
17. or jamb at 1 5mm deep for the strike plate which must fit flush with the door jamb Insert the strike lining box and then fasten screws to the plate 12 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 4 3 Sizing Tail Piece to the correct door thickness The Actuator Systems NextBolt is designed to fit door thicknesses of 35mm to 50mm There is one 50mm tailpiece pre installed in your NextBolt outside unit with indentations at 35mm 38mm and 45mm Cut here for 35mm 38mm 45mm Ve 4 1 Measure the thickness of your door 2 We recommend you use a pair of hand held bolt cutters to cut the tailpiece at the required length 3 Smooth the edges with a file recommended 13 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au IF YOUR DOOR THICKNESS DOES NOT EXACTLY MATCH ANY OF THE INDENTATIONS e g YOUR DOOR IS 40MM THICK MEASURE THE REQUIRED LENGTH WITH AN ACCURATE RULER TO THE NEAREST INDENTATION MARK WITH A PERMANENT MARKER AND TRIM AS REQUIRED Notes The motor could be dislodged if the tailpiece is not cut properly and is too long due to excessive pressure Warranty will be voided if this occurs 14 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Aust
18. or to R position see next page for definition Very Important If this switch is in the incorrect position the lock will not function properly 17 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 2 Left handed doors are defined as hinge on the left when you are entering the home from outside The opposite is true for right handed doors Right Hand Door Right Handed Left Handed 3 Plug wire set into circuit board making sure all prongs are firmly seated 18 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 4 Press sheathing of wire casing into the wire holder clamp 5 Turn the manual turn knob to the vertical position facing downward 19 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 6 Insert the tail piece into the vertical retaining slot of the indoor unit 7 Gently finish joining the outdoor and indoor units together ensuring all fixing posts are aligned properly 8 Fasten the two shorter screws through the upper fixing post holes on the upper section of the inside unit 20 NextBolt User Manual For support contact us at support advancedactuators com au Actuator S
19. ort advancedactuators com au Actuator Systems Australia http www advancedactuators com au APPENDIX A FINGERPRINT ENROLLMENT CODES ee a KEYPRESS SEQUENCE OPEN CLOSE O CB NAME FINGER USED L R DATE ADD 2 ADD DEL O CB 3 ADD ADD O CB 4 ADD DEL DEL O CB 5 ADD DEL ADD O CB 6 ADD ADD DEL O CB y ADD ADD ADD O CB 8 ADD DEL DEL DEL O CB 9 ADD DEL DEL ADD O CB 10 ADD DEL ADD DEL O CB 11 ADD DEL ADD ADD O CB 12 ADD ADD DEL DEL O CB 13 ADD ADD DEL ADD O CB 45 NextBolt User Manual For support contact us at support advancedactuators com au Systems Actuator y Australia 14 15 16 17 18 19 20 21 22 23 24 25 26 2A 28 29 30 ADD ADD ADD DEL O CB ADD ADD ADD ADD O CB ADD DEL DEL DEL DEL O CB ADD DEL DEL DEL ADD O CB ADD DEL DEL ADD DEL O CB ADD DEL DEL ADD ADD O CB ADD DEL ADD DEL DEL O CB ADD DEL ADD DEL ADD O CB ADD DEL ADD ADD DEL O CB ADD DEL ADD ADD ADD O CB ADD ADD DEL DEL DEL O CB ADD ADD DEL DEL ADD O CB ADD ADD DEL ADD DEL O CB ADD ADD DEL ADD ADD O CB ADD ADD ADD DEL DEL O CB ADD ADD ADD DEL ADD O CB ADD ADD ADD ADD DEL O CB NextBolt User Manual For su ort contact us at su http www advancedactuators com au 46 ort advancedactuators com au Actuator Systems Australia http www advancedactuators com au 3 ADD ADD ADD ADD ADD O CB a2 ADD DEL DEL DEL DEL DEL O CB 33 ADD DEL DEL DEL DEL ADD O CB 34 ADD DEL DEL
20. os Actuator stems Australia http www advancedactuators com au PREFACE gt Thank you for purchasing the Actuator Systems Australia NextBolt Secure Mount fingerprint deadbolt PLEASE ENSURE YOU HAVE OUR SECURE MOUNT OR MODEL BEFORE PROCEEDING IF YOU HAVE OUR EZ MOUNT EDITION PLEASE USE THE EZ MOUNT MANUAL INCLUDED ON YOUR CD Please read the documentation carefully before installation amp use The manual details all installation procedures and operation steps Manufacturer and or Distributors of the Actuator Systems Australia NextBolt will not be responsible for any damages caused by incorrect installation or mishandling of the lock Any such damages will void manufacturer s warranty l NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au Contents losta lahon Mantal eercenete tacsud esas cciecnenarcaiete rE E E E TEE 3 DIN IAS E EEE E E E 3 2 IROGUIC CT TOOTS E A A E E 5 JePe USE ALAN e E 6 3 1 Mark and bore holes on the doof ssesseeeeeeseeseesssssssse 6 3 2 Deadbolt Latch Length Selection eee 10 Gps MVS AAU A E A E E E E E A se awennce ee 11 4 1 Installation of Deadbolt i eeeeseesseeeeeeeeeeeeeees 11 4 2 Installing Strike and Strike Lining Box on the door TD ee n E E T E 12 4 3 Sizing Tail Piece to the correct door thickness 13 4 4 Installation of the Outdoor Unit
21. p www advancedactuators com au 99 ADD ADD DEL DEL DEL ADD ADD O CB 51 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au We would like to personally thank you for your purchase of our exciting NextBolt NX Series biometric deadbolt lock from Actuator Systems We hope you enjoy using it as much as we enjoy developing this technology for you For more helpful information about your NextBolt please visit www advancedactuators com au support php or our knowledgebase at http www advancedactuators com au kb For all Tech Support Questions Call 1300 905 299 or email support advancedactuators com au Frequently Asked Questions FAQ Here are a few answers to common installation questions These account for 90 of the inquiries we receive to our technical support department 1 When you mate the front and back of the lock together insure the bolt is in the locked out position and the knob is pointing directly down This will cause the notch the tailpiece fits into to be in a vertical position 2 Insure the wire that runs between the two lock pieces does not interfere with the rotation of the tailpiece 3 Issues with fingerprint recognition are due to a poor enrollment 95 of the time High quality enrollments are the key to fast and reliable operation of your new lock Ensure when you place your finger on the pad for enrollment
22. posts mounted on the top plate of the outdoor unit as indicated on the installation template 3 12 Bore holes Bore a 54mm diameter hole in the center of door face for chassis It is recommended to bore this hole from both sides of the door to avoid splintering Bore a 25mm diameter hole in the center of door edge for deadbolt Bore two separate 10mm diameter holes for the upper fixing posts 9 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 3 2 Deadbolt Latch Length Selection The adjustable deadbolt included with your purchase is nominally set at the 60mm position If you desire the backset at the 70mm position follow the steps below 60mm 70mm DO NOT REMOVE 1 Place your middle finger on one side of the pin and your thumb on the other side while placing your index finger on the top of the backset 2 Push up with your thumb and middle finger 3 Use a flat tool to push out on the backset to the 70mm 2 3 4 position shown in completed 70mm position 4 Release upward pressure from the pin to ensure the new position is clicked into place 5 To adjust for the 60mm 2 3 8 position follow steps 1 and 2 and use your forefinger to push the backset into the 60mm position and it clicks into place WARNING Do not remove the adjustment pin to adjust the backset length position This will
23. quence has begun Long Double Beep Indicates that Delete All programming was successful Four Beeps Indicates unsuccessful enrollment unsuccessful verification attempt OR Actuator Systems NextBolt was improperly installed see Installation Guide Five Beeps _ Indicates the selected user was unsuccessfully deleted Six Short Beeps Low battery alert change batteries Common definitions of terms used when using the Actuator Systems NextBolt Fingerprint Enrollment Process of adding fingerprints to the Actuator Systems NextBolt Enrolled Fingerprints Fingerprints that have been successfully added into the Actuator Systems NextBolt Verifying Fingerprints Process of authentication by scanning enrolled fingerprints to A Unlock the door B Authenticate Administrators enrolled fingerprints to program the Actuator Systems NextBolt 27 NextBolt User Manual For support contact us at support advancedactuators com au Actuator D australia http www advancedactuators com au Before enrolling and verifying fingerprints make sure to read the following helpful hints for Fingerprint Enrollment and Verification Generally the center of the vortex swirl of the fingerprint pattern is the key data point ideally it is placed in the center of the small glass window in a consistent way Your finger should be flat motionless and held with light pressure in the same way each time See the picture below for some guiding
24. r AD AEA A Put the finger center on the BAND BAT NI center of the scanner window N p Ni y i p a a Place finger flat on the voc ad in l iy j window Good Bad Bad Don t put finger on the edge and then move to the center Raise the finger then leave D scanning window after ji he fingerprint scanning Don t drag the finger on the surface of the scanning Important Programming Notes window When Adding or Deleting Fingerprints the closed sliding cover must be fully lifted within 8 seconds after pressing the ADD or DEL button or the NextBolt will power off If this occurs simply close the sliding cover press the ADD or DEL button again and fully lift the sliding cover immediately to restart the programming sequence The first two fingerprint users enrolled will automatically be programmed as ADMINISTRATORS Users and 2 ADMINISTRATORS can apply all programming functions as well as verify their fingerprints to unlock the door 29 NextBolt User Manual For support contact us at support advancedactuators com au Actuator W Systems Australia http www advancedactuators com au The 3rd thru 99th fingerprint users enrolled Users 3 thru 99 are automatically programmed at the USER level USER level fingerprints can only be used to unlock the door not to program the lock Section I Enrolling Administrators First Fingerprint User Sliding cover must be closed before any programming sequen
25. r finger on the sensor window during the first of three scans e Keep your pointer finger on the scanning window until you hear a single long beep or four beeps After the scanning is completed you will hear one of the following o Single long beep indicating that the operation was successful OR o Four beeps indicating that your fingerprint was not successfully enrolled If you hear four beeps please start the enrollment process over from the beginning Once enrollment begins users can be enrolled consecutively without the need to verify the administrator again After you hear the long beep simply enter in the next KEYPRESS SEQUENCE from the APPENDIX A for the next user e Close the sliding cover to end the enrollment procedure 35 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au Section III Deleting Individual Fingerprint Users Sliding cover must be closed before any programming sequence can begin The Individual Fingerprint User Deletion programming function deletes the individual user you select from your enrolled users Please use the following steps to delete individual fingerprint users e With the battery cover removed press the DEL button located on the indoor unit e Short Double Beep will be heard 36 NextBolt User Manual For support contact us at support advancedactuators com au
26. ralia http www advancedactuators com au 4 4 Installation of the Outdoor Unit 1 Attach the rubber gasket to the back of the outdoor unit 2 Make sure the tail piece is vertical Very important ensure the inscribed word UP is orientated correctly 15 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia NextBolt User Manual http www advancedactuators com au 3 Make sure the deadbolt is engaged use a Phillips screwdriver to extend the deadbolt through the cross as shown Very important If the bolt is NOT extended as shown prior to mating the front and back units the lock will work in reverse You will then have to un install the unit s to extend the deadbolt to ensure proper operation 4 Insert tail piece through the cross slot of the latch 5 Insert the connector and wire through the cylinder hole below the deadbolt latch 16 For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 6 Insert the two upper fixing posts through the small upper holes on the door the newly drilled holes 4 5 Installation of the Indoor Unit 1 Select the proper door opening orientation on the back plate of the Indoor Unit If the door is left handed please push the orientation selector switch to L position if it s right handed switch the select
27. rints can only be used to unlock the door not to program the lock whereas enrolled fingerprints 1 amp 2 have Administrator rights Please use the following steps to enroll additional fingerprint users Users 2 thru 99 USER 2 has Administrator rights e Remove the battery cover from the indoor unit e Press the ADD button located on the indoor unit e Single beep will be heard 33 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia W 34 NextBolt User Manual For support contact us at support advancedactuators com au http www advancedactuators com au e Fully open the sliding cover located on the outdoor unit immediately e Sensor will flicker for less than one second A single short beep will be heard and the fingerprint sensor will power on After the fingerprint sensor powers on rest an ADMINISTRATOR S finger on the sensor window to verify that they are an Administrator When the first Administrator s fingerprint is successfully verified the sensor will briefly turn off for less than one second Immediately remove the ADMINSTRATOR S finger and enter the KEPRESS SEQUENCE for the user number you wish to enroll described in APPENDIX A Actuator Systems Australia http www advancedactuators com au W e A single short beep will be heard and the fingerprint sensor will power on e Rest the new user s pointe
28. t User Manual For support contact us at support advancedactuators com au Actuator W Systems Australia http www advancedactuators com au Section VII Locking and Unlocking the Actuator Systems NextBolt from Inside In case of emergency manual turn knob can be used to disengage the deadbolt Please use the following steps to lock and unlock the Actuator Systems NextBolt from inside 7 e Press the gt OPEN CLOSE L button located between the ADD and DEL buttons J z 4 e Deadbolt will 4 engage disengage and single short beep will be heard Prr a ermm SAR A ai 4 f Be cy 7 43 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au Support Contact the Actuator Systems NextBolt dealer that you purchased the lock from OR Contact us at support advancedactuators com au for additional Support Training videos of the NextBolt can be found at http www advancedactuators com au support training videos Support documentation can be found at http www advancedactuators com au support nextbolt documentation 9 FAQ s for the NextBolt can be found at http www advancedactuators com au kb Quick Reference Guide and Handy Enrolment table can be downloaded at http www advancedactuators com au support nextbolt documentation 9 44 NextBolt User Manual For support contact us at supp
29. ystems Australia http www advancedactuators com au 9 Fasten the two long screws through the bottom fixing post holes on the inside unit 10 Move the manual turn knob back and forth to ensure that deadbolt opens and closes mechanically Ensure the deadbolt extends a full 25mm 2 5cm and retracts flush with the strike plate 21 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 11 Insert 4 high quality AA batteries 12 Press the electronic open close button to ensure that the deadbolt opens and closes electronically Ensure the deadbolt extends a full 25mm 2 5cm and retracts flush with the strike plate 22 NextBolt User Manual For support contact us at support advancedactuators com au Actuator Systems Australia http www advancedactuators com au 4 6 Final inspection adjustment prior to enrollment Note After installation and prior to using the unit make sure you read and follow the steps below 1 Turn the inside knob to the horizontal position next turn it to the vertical position locked position It should turn freely If and when the inside and outside locks are attached securely and the inside knob doesn t turn freely see the trouble shooting table below for possible solution If the knob turns freely continue with the next step 2 Try to lock and unlock from outside by fully opening
Download Pdf Manuals
Related Search