Automatic Drum Washer
Contents
1. Please check against the following table before call for servicing If any fault actually exists please contact our After sales Service Department and do not repair by yourself Please unplug the power plug before check 21 operation i a z Oo c z Phenomenon There is a small amount of water in the drain pipe and washer dryer when 1 Itis normal and the water is the remaining water of factory using for the first time inspection I The washer dryer does not operate 1 ii gt Buttons cannot be operated Water leakage occurs at the water tap gt up water feed or slow water feed y ii gt Check whether power failure or abnormal power supply occurs Check whether the power plug is firmly plugged in the socket Check whether the fuse of power supply or the current breaker is in good condition oO Check whether the power switch is pressed Check whether the water tap is turned on oO Check whether the delay function is activated Check whether the Start Pause button is pressed Check whether the child lock function is activated Refer to the instructions under the title of Cancel or reselect a program in the process of running in the sectionof 13 Other Functions Check whether the shape of water tap is suitable Check whether the water inlet pipe joint is installed in place Check whether the water tap is damaged Check whether the2. weight of articles in each net bag must not exceed 300g and the net bags should be put in the washer dryer together with those clothes not in a net bag otherwise the washer dryer will not be balanced and result in abnormal vibration Reference weights for small articles handkerchiefs about 30g piece gloves about 60g pair cotton socks about 30g pair silk socks about 20g pair 16 When spinning at high speed the clothes will stick on the washer dryer s inner drum wall due to centripetal force If the clothes are to be dried it is recommended to take them out and fluff them out then put them in the washer dryer again for drying to achieve optimal drying effect 17 During heating or drying high temperature inside the washer dryer may cause temperature rise of the tabletop panel and door etc Therefore do not touch the tabletop panel and door during heating or drying 18 During drying it is recommended not to load the inner drum with clothes over the height of drying sticker on the electroplated ring otherwise inadequate drying may occur Haier To clean the drying filter box Note Please clean the drying filter box after using the drying function every time 1 Pull out the drying filter box as shown in Fig 1 2 Gently open the drying filter box cover as shown in Fig 2 3 Remove the flocking in the drying filter box with a soft bristle brush as shown in Fig 3 4 Close the drying filter box and install it in place
3. Fig 1 Fig 2 Fig 3 Note The flocking must not be piled up around the washer dryer to avoid its entry into the washer dryer and poor drying effect To clean the water inlet filter screen Warm tips To improve the washing effect do not throw away the water inlet filter screen In case of unsmooth water feed please clean the water inlet filter screen in time as follows Ae 1 Screw off the water inlet pipe as shown in Fig 1 Py and then take out the filter screen with a pair of gt nipper pliers as shown in Fig 2 2 Wash the filter screen with a soft bristle brush 3 Install the filter screen in place and connect the water inlet pipe Fig 1 Fig 2 20 Haier 14 Cleaning Maintenance A Please unplug the power plug from the socket before cleaning and maintenance After finishing washing please turn off the water tap and remove the water inlet pipe Unplug the power plug and put back the drain pipe If the washer dryer is not to be used for a long time please keep the door slightly open and dry the window pad to avoid unpleasant smell Do not use organic solvent or corrosive liquid to wipe the washer dryer s exterior and rubber parts Frequently clean both the water inlet pipe joint and water inlet valve filter screen to prevent them from being clogged by dirt To clean the drain filter once every 30 days 1 After draining the water in the washer dryer press the filter cover wit
4. e AL 2 displays when there are about 2 4kg clothes in the washer dryer i i e AL 3 displays when there are about 4 6kg clothes in the washer dryer orma promp X 3 X 4 i e AL 4 displays when there are about 6 8kg clothes in the washer dryer X 5 i e AL 5 displays when there are about 8 10kg clothes in the washer dryer Being inconsistent with the conditions gt for door opening it is not allowed to Normal prompt unlock the door TT Child lock prompt Tt Normal prompt gt The whole program ends i Normal prompt La y gi door locking or unclosed gt Close the door if the code remains please ask for repair gt Drainage faulr The words Drain Filter on the display screen flash Abnormal water feed Check whether the outlet of drain pipe is 10cm above the floor Clean the drain filter and check whether the drain pipe is clogged if the code remains please ask for repair Check whether the water tap is turned on whether the water pressure istoo low whether power supply cut off occurs Press the Start Pause button to clear it if the code remains please ask for repair Check whether the outlet of drain pipe is 10cm above the floor Clean the drain filter and check whether the drain pipe is clogged if the code remains please ask for repair Tt Abnormal drying water level Unbalanced clothes distribution when spinning The words Imbalance on the display screen flash Check the adjsuyabl
5. e feet to confirm whether the washer dryer is level Take out and fluff out the clothes if the code remains please ask for repair i Take out some clothes The clothes weight is beyond the acceptable range The words Overload on the display screen flash gt Reinstall the drying filter if the code remains please ask for repair In case of the following alarms press the Off button to clear them If they remain unplug the power plug and contact our After sales Service Department In case of the following alarms press the Off button to clear them If they remain unplug the power plug and contact our After sales Service Department 23 ONoOahWND a Ss Ss O akwonrd SdeyiarccCahiicn sea w a Vrs i a ek UA cone 1 PrecautonstonUsSS kena fF ar a aa i 2 Components ker a yS 27 A a F ah e 4 Accessalles a Fa a a ae ae O a se 5 Notice bet ie Uses eer a fen i a M 5 ConiolPanelkand RrogramiDescrphonies ma Guak Wi ua ae ese CC 9 Display Screen aa a 7s i of nee a 11 ProgramstQuidem w S au r a a a a 13 Operational Rroceduress da aa a a a 14 GeperalRiogramRunning Processa Toena a a a 15 yesaratians beloreNashing we Tor qe S a 16 Reference Weight for Different Types of Clothing 5 sess ge 16 henFunCtionsmms tay Pia S F Sg aa 17 Gleamno Maintenance dp Py C wte E uO j 19 Ranii iagnosigand Soltions amahai wa Ee ee 21 Haier 1 Safety Precautions A Electrical safety prompt P
6. eakage do not plug or unplug the washer dryer s power plug The washer dryer s door and tabletop panel are relatively hot during heating and drying For the purpose of safety keep the children away from the washer dryer In addition when F draining hot water be careful to avoid scald APR After unpacking the washer dryer do not allow the children to play with the disassembled packaging materials such as carton plastic packaging bag and foam etc Do not install the washer dryer outdoors and in excessively humid environment otherwise moisture on the electrical components may easily cause damage to the ignition system or other accidents In case of inadvertent water spray onto or into the washer dryer only after the washer dryer is thoroughly dried can you use it Neither should you place the washer dryer directly onto an airproof carpet in order not to block the bottom vent nor place it close up to the wall or furniture to avoid accidents Do not use the washer dryer on any platform above the floor otherwise it may fall off onto the floor and be damaged Phenomenon Poor washing effect Forceless washing Stop operation during washing Repeated rinsing Loud noise when spinning Vibration and displacement The clothes are not spun dry agter finishing the spinning progran No water discharge or slow water discharge The washing does not end after the preset delay time gt Check the detergent for
7. h a hand to open it as shown in Fig 1 2 Press the push switch to the end to prevent the hand from being wounded when turning the filter knob then anticlockwise screw out the drain filter with a hand Note A little water may flow out when screwing out the filter knob if Err2 alarm appears relatively much water may flow out when screwing out the filter knob Therefore prepare a container e g basin before screwing out the filter knob and make the water flow in the container but not onto the ground or floor 3 Remove the thrums and impurities on the filter and rinse the filter with clean water 4 Insert the filter along the groove and tighten it by turning clockwise otherwise water leakage may occur Be careful not to distort the filter Note The drain filter must be tightened to avoid water leakage 5 Press the push switch again with a hand to make it bounce out then close the filter cover Push switc oosen Drain filter knob Groove Drain Drain filter filter cover aA Fig 2 Fig 3 To clean the distributor box 1 Fully pull out the distributor box 2 Slightly lift up and pull out the distributor box 3 Rinse the distributor box and siphon cap with clean water 4 Buckle the siphon cap then insert push in and close the distributor box Note Please buckle the siphon cap in the correct position of distributor box otherwise the detergent and softener in the distributor box cannot be siphoned into
8. lease pay attention to electrical safety during use The plug should be accessible after the washer dryer is installed in place Do __ not disconnect the plug from the socket by pulling the power cord If the E power cord needs to be replaced ask a qualified technician or contact our ye SAL j After sales Service Department for replacement Prevent the power cord s WR from being pressed by any foot and from such problems as break off flattening etc Power supply must use an independent socket the grounding terminal of which must be properly grounded The socket must be a qualified product Such overload protective devices as proper fuse must be available at the user s home And the ammeter wire and socket must be able to withstand 10A current Warning sign The contents with this sign involve the safety of both the product and the user Be sure to strictly follow these instructions otherwise the washer dryer may be damaged or the user may be injured Keep the washer dryer away from any heat source and direct sunlight to prevent the aging of plastic and rubber parts Prohibitory sign The contents with this sign indicate the behaviors to be absolutely prohibited Failure to follow these instructions may result in damage to the washer dryer or personal injury Do not use such chemicals as flammable detergent and dry cleaning solvent to wash the clothes Do not use any flammable spray near the washer dryer In case of flammable gas l
9. m g fi e Automatic Drum Washer dryer HW100 HB1297NZP si Tiana User Manual Please read these instructions carefully before use Please save these instructions for future reference Haier Product Features DD inverter frequency motor technology Function Stop just in time upon cleanness Hybrid balance technology 8 Drawer type box Inclined drum Function of Supporter Dry Large capacity Self cleaning function Optimal door height design Air wash function Large caliber clothes loading opening Technology of anti bacteria and mildew proof with JIT function Stop just in time upon window pad drying O Large high brightness LCD Specifications koa The diagrams in this manual are for illustrative purpose only Due to continuous product improvement pleasesee the actual product for appearance color and accessories which may be inconsistent with those described in this manual Here we apologize for this This product is classified as Class appliance Please pay attention to electrical safety during use Please ensure that Water inlet pressure is higher than 0 03 MPa while drying Haier 15 Fault Diagnosis and Solution code m a c F r m J Ge eae La The washer is in automatic weighing state _ Normal prompt La Code for the clothes weight X 1 i e AL 1 displays when there are no clothes or less than 2kg clothes in the washer dryer X 2 i
10. nt Press the lower end of locking lever Hold the water inlet pipe press down the slider and remove the water inlet pipe joint Locking lever Slider Water inlet pipe Haier Buzzer mute function Select the self clean program simultaneously press and hold the Delay and Temp buttons for 3s to mute the buzzer for all the programs excluding the alarm sound and the display screen will display oEEP OFF Simultaneously press and hold the Delay and Temp buttons for 3s to resume the beep for all the programs and the display screen will display bEEP On Memory program When selecting the Memory program all the washing parameters set by the user will be memorized after the program ends If the user wants to wash with the same settings just select the Memory program after turning on the washer dryer This program does not memorize the delay function set by the user Spin program To select the Spin program only just anticlockwise ture the program knob after turning on the washer dryer by pressing the On button Press the Spin button to set the spinning time press the Speed button to set the spinning speed Air Wash function This function is available in the Dry mode The inner drum rotates during air wash and removes the moisture and unpleasant smell from the clothes via hot air Please turn on the water tap before star
11. ped with downward drainage system Please install the washer dryer in a location with floor drainer 10 Using the washer dryer at or below 0 C may damage the water inlet valve and drainage system If the washer dryer is stored at or below 0 C be sure to move and leave it in the environment at room temperature for 2 4 hours before use 11 Do not put the clothes tainted with chemicals into the washer dryer 12 It is prohibited to dry the clothes with oil stains to avoid fire hazard 13 When any program other than Supporter Dry is selected it is prohibited to put the drying rack into the washer dryer to avoid damage to the washer dryer 14 When using the washer dryer s drawer Do not put any flammable explosive and corrosive substance in the drawer Do not pour detergent and washing powder into the drawer to prevent the drawer from being contaminated The maximum weight of all the items in the drawer must not exceed 5kg Please close the drawer immediately after you use it Neither should you put wet clothes on the drawer nor allow the children to play with and step on the drawer to avoid deformation or damage of the drawer Haier 15 When washing small articles e g handkerchiefs gloves socks etc and those clothes liable to inter twist and wear please put them in net bags for washing rinsing and spinning to prevent them from falling into between the inner drum and window pad and further avoid inadequate washing and drying The
12. plastic parts 4 Do not wash such waterproof articles as raincoat bicycle cover and down products as well as carpet to avoid abnormal vibration or damage to such articles 5 Please add a proper amount of washing powder detergent or bleach and softener in corresponding chambers of the distributor box before starting the selected program Do not open the distributor box during the program running to avoid some detergent or bleach left in its chamber 6 If a brassiere with steel wire is washed in the washer dryer the steel wire may bounce out Therefore do not wash any brassiere with steel wire in order to protect the washer dryer 7 The washer dryer s door is equipped with a self lock safety device Press the Start Pause button to make the washer dryer in pause if the washer dryer is operating Only when the washer dryer is in the safe state the water level is below the lower edge of sight glass the temperature inside of the drum is below 50 C and the inner drum is not rotating and the door lock icon is not illuminated can you open the door by pressing the door opening button Never forcibly open the door before the washer dryer enters the safe state to avoid damage to the door or scald 8 Turn off the water supply and power supply after finishing washing every time Meanwhile clean the sight glass window pad interlining to prevent contaminants from tainting the clothes again 9 The washer dryer described in this manual is equip
13. proper type and dosage Check whether a proper program is selected Check whether the clothes weight exceeds the washer dryer s rated washing capacity Check whether sudden power failure or power supply cut off occurs Check whether the Srart Pause button is pressed The washer dryer with the function of automatic shutdown upon clean detected automatically increases or decreases the times of rinsing 1 2 times according to the degree of dirtiness of the clothes The washer dryer s program is set with discharge time and the spinning starts after a period of time Check whether the clothes intertwist Check whether all the packaging bolts are removed Check whether the washer dryer is level The feet can be adjusted to level the washer Check whether the clothes intertwist Check whether the washer dryer collides with other objects Check whether there are forergn bodies in the washer dryer The spinning effect varies with type of clothes Check whether eccentric protection functions due to few clothes Check whether thedrain pipe is bent clogged or frozen Check whether the outlet of drain pipe is 10cm above the floor Check whether the filter is clogged Poor water feeding drainage conditions or unbalanced clothes distribution results in longer time Haier 15 Fault Diagnosis and Solution The following phenomena are not necessarily faults of the washer dryer
14. the washer dryer s drum 19 Haier 3 Components Main control panel Drying filter box Tabletop pannel l l I Distributor ed box _Door opening button Electroplated _ ring Drain pipe hook 1 on each side Door _ _ Handle 2 on each side Drain filter cover l l l I I I l l l l Front adjusttable foot 2 Drawer Drain pipe joint Haier 4 Accessories ee 7 il l 7 AS l Daea aes E iTo 5 i PE AA if G i oe Sf W S u Inlet pipe assy 1 Drain pipe assy 1 Drain pipe clamp 1 Drying rack 1 Hoer 5 5 W Vis warono E E A an Packaging bolt cover 4 User manual 1 Warranty Card 1 Anti Rat Cover 1 Screw 8 a5 oat aa 4 a Gs ER Gas 5 Notice before Use Before using please take out the foam piece between equilibrium wreath and window This only is used for transport so please must take it out with other packing pieces at the same time Please install and adjust the washer according to the instructions in this manual so that you can use it in a safe manner O To connect the water inlet pipe Please use the new water inlet pipe delivered with the washer dryer 1 Select a proper water tap The lengh of front end must be more than 10mm F RT In case of unsmooth end face of the water tap outlet sae please file it smooth to avoid water leakage 2 Remove the water inlet pipe joi
15. ting air wash Tub Clean function This function is available in the Wash and Wash amp Dry modes and used to wash away the dirt from inner and outer drums Note that clothes must not be put in the washer dryer when using this function The function of drying with rack This function is used to dry those articles liable to y deformation such as hat cloth doll and cloth shoes etc Make sure that the articles in the washer dryer are suitable for drying with washing machine When using the function of drying with rack put the drying rack in the drum as shown in Fig 1 Insert the protuberance at the front end of drying rack into the hole of inner drum cover place the back end of drying 18
16. water tap is tured on and whether water supply cut off occurs Check whether the water inlet filter screen is clogged If necessary clean it Check whether the water tap and water inlet pipe are frozen Check whether the Delay program is selected Check whether the Start Pause button is pressed Check whether the water inlet pipe is bent Check whether the water pressure is too low Check whether the washer dryer inclines or shakes Check whether there are foreign bodies such as coins and zippers in the washer dryer Check whether the noise is from the draining pump or motor in normal operation Haier 2 Precautions for Use 1 Due to the fluctuation of water pressure please check all the joints of water inlet pipe water tap and drain pipe for firm connection before washing every time In case of loose water pipe connection or water leakage please turn off the water tap and take proper measures or contact our After sales Service Department for reconnection Only after such faults are cleared can you use it again 2 When the washer dryer is not in use please keep the door slightly open and towel off both the window pad and door glass to avoid unpleasant smell Do not cover the washer dryer with a plastic bag to avoid moisture staying in it 3 Do not place any heavy object heat producing appliance and item liable to water liquid leakage on the table top to avoid deformation of the tabletop panel and
Download Pdf Manuals
Related Search