TPC-1270 User Manual
Contents
1. Hot surface Figure 1 1 1 0 port arrangement TPC 1270 User Manual 6 1 7 Panel Mounting 1 There is a piece of adhesive waterproof gasket on the Mg AL front bezel Make sure the waterproof gasket is in position before installing the TPC 1270 to the panel opening 2 Install the TPC 1270 to the panel opening 3 Find out the eight clampers and eight long screws in the accessory pack Hook those clampers to those holes around the four sides of the bezel Insert the screws to every clamper and fasten them These screws will then push on the mounting panel and fix the unit 4 The mounting panel thickness is suggested to be less than 10mm 0 236 inch Figure 1 2 Panel Mounting 7 Chapter 1 1 8 Dimensions amp Cutout Weight 3 5 Kg without HDD Dimensions 311 x 237 x 65 mm WxHxD Cutout 312 5 x 228 5 mm suggested i Lu Figure 1 3 Dimensions TPC 1270 User Manual 8 Chapter 2 System Setup This chapter provides a brief explanation for operating the TPC 1270 It is easy to make the TPC 1270 start working with the below step by step Step 1 Unpack the TPC 1270 package Please check the packing list at the beginning of this manual Step 2 Install a CompactFlash containing Windows XP Embedded or other operating system Figure 2 1 Install CompactFlash memory card Warning It is suggested to turn OFF system power as plug in or pull out the memory card though the C2. TPC 1270 Intel Touch Panel Computer with High Luminance 12 1 SVGA TFT LCD User Manual Copyright The documentation and the software included with this product are copy righted 2007 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this man ual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reli able However Advantech Co Ltd assumes no responsibility for its use nor for any infringements of the rights of third parties which may result from its use Acknowledgements Intel and Pentium are trademarks of Intel Corporation Microsoft Windows and MS DOS are registered trademarks of Microsoft Corp All other product names or trademarks are properties of their respective owners Part No 2003127000 Ist Edition Printed in Taiwan May 2007 TPC 1270 User Manual ii Product Warranty 2 years Advantech warrants to you the original purchaser that each of its prod ucts will be free from defects in materials and workmanship for two years from the date of purchase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have bee
3. 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer iii Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring We recommend the use of shielded cables This kind of cable is available from Advantech Please contact your local supplier for ordering information FCC Class A Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environ ment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Opera tion of this equipment in a residential area is likely to cause harmful inter ference in which case the user will be required to correct the interference at his own expense Technical Support and Assistance Step 1 Visit the Advantech web site at www advantech com support where you can find the latest information about the product Step 2 Contact your distributor sales representative or Advantech s cus tomer service center for technical support if you need additional assistance Please have the following information ready before
4. gt 1717MB Windows ECT 112 gt 38900MB 8 WinRAR ERITA A 204MB Figure E 6 Uninstall 2 TPC 1270 User Manual 66 E 3 Touchscreen Calibration The PM the icon of the PenMount Control Panel is in the menu bar after the touchscreen installation Please click the icon PM to call Pen Mount Control Panel It contains six functions Calibrate Draw Multiple Monitors Option and About Multiple Monitors is for multiple displays only however TPC 1270 only provides one touchscreen display This function is not workable on TPC 1270 About is to show the driver ver sion Calibrate Two ways to calibrate the touch screen include Standard Calibration and Advanced Calibration Standard Calibration is to adjust most touchscreens Calibrate Draw Multiple Monitors Option About Advanced Mode s Blet calibration data Advanced Calibration Standard Calibration Figure E 7 Standard Calibration 1 67 Appendix E Touch the red square Figure E 8 Standard Calibration 2 Touch the red square Figure 9 Standard Calibration 3 TPC 1270 User Manual 68 Note Touch the red squares in sequence The cali bration is completed after the fifth touch red point is calibrated Press ESC to skip Advanced Calibration is for the aged touchscreens by using 4 9 16 or 25 points to calibrate touch panel zinixi Calibrate Draw M
5. Netzkabel oder Netzstecker sind besch digt b Fl ssigkeit ist in das Ger t eingedrungen c Das Ger t war Feuchtigkeit ausgesetzt d Wenn das Ger t nicht der Bedienungsanleitung entsprechend funk tioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erz lelen e Das Ger t ist gefallen und oder das Geh use ist besch digt f Wenn das Ger t deutliche Anzeichen eines Defektes aufweist 15 VOSICHT Explisionsgefahr bei unsachgemaben Austausch der Batterie Ersatz nur durch densellben order einem vom Hersteller empfohlene mahnlichen Typ Entsorgung gebrauchter Batterien navh Angaben des Herstellers 16 ACHTUNG Es besteht die Explosionsgefahr falls die Batterie auf nicht fach m nnische Weise gewechselt wird Verfangen Sie die Batterie nur gleicher oder entsprechender Type wie vom Hersteller empfohlen Entsorgen Sie Batterien nach Anweisung des Herstell ers Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 betr gt 70dB A oder weiger Haftungsausschluss Die Bedienungsanleitungen wurden entsprechend der IEC 704 1 erstellt Advantech lehnt jegliche Verantwortung f r die Richtigkeit der in diesem Zusammenhang get tigten Aussagen ab TPC 1270 User Manual viii Chapter NR E u SU 1 8 Chapter 2 Chapter 3 Chapter Chapter Main Un Appendix A 1 Contents General Information 42 2 Introductio
6. TPC 1270 User Manual 38 Enable EWF Run OSLock and then system reboot automatically Open those software that customers want to directly use after system resume from hibernation Hibernate via Advantech HORM utility Please Click Start Menu gt All Programs gt Advantech gt HORM HORM environment remains all along unless the following events occur Run EWF commit command ewfmgr c commit and then reboot sys tem Select Discard hibernation file by clicking F8 when system is starting up Also HORM cannot fit your system if free space in C partition is not enough The hibernation file required is dependent on the RAM size you use on the system In other words the hibernation file is 512MB that is the same as memory size used on TPC 1270H PIE or 1270 5 3 Advantech Utilities TPC 1270 provides the useful utilities for users to configure the HORM and EWF 5 3 1 Version Information Start menu gt All Programs gt Advantech This states the current XPE runtime information including hardware plat form version build number release date XPE QFEs installed in compo nent database and XP Pro Patches you installed manually 39 Chapter 5 5 3 2 OSLock and OSUnLock The two utilities assist users to enable or disable EWF Please go to Start Menu gt All Programs gt Advantech The default setting of EWF is dis abled Users can protect C partition from any disk writing via OSLock that is to enable EW
7. 51 ChapterB Mov al 30h Out dx al Inc dx Mov al 01h Out dx al Dec dx Enable watchdog timer to be reset by mouse Mov al 0f7h Out dx al Inc dx In al dx Or al 80h Out dx al Dec dx lock W83627HF Mov al 0aah Out dx al 4 Enable watchdog timer to be reset by keyboard Mov dx 2eh unlock W83627H Mov al 87h Out dx al Out dx al Mov al 07h Select registers of watchdog timer Out dx al Inc dx Mov al 08h Out dx al TPC 1270 User Manual 52 Dec dx Enable the function of watchdog timer Mov al 30h Out dx al Inc dx Mov al 01h Out dx al Dec dx Enable watchdog timer to be strobed reset by keyboard Mov al 0f7h Out dx al Inc dx In al dx Or al 40h Out dx al Dec dx lock W83627HF Mov al 0aah Out dx al 5 Generate a time out signal without timer counting Mov dx 2eh unlock W83627H Mov al 87h Out dx al Out dx al Mov al 07h Select registers of watchdog timer Out dx al Inc dx Mov al 08h Out dx al 53 Chapter B Dec dx Enable the function of watchdog timer Mov al 30h Out dx al Inc dx Mov 1 01 Out dx al Dec dx Generate a time out signal Mov al 0f7h Out dx al Write 1 to bit 5 of F7 register Inc dx In al dx Or al 20h Out dx al Dec dx lock W83627HF Mov al 0aah Out dx al TPC 1270 User Manual 54 APPENDIX Accessory Kit Assembly This appendix shows how to connect to a CD ROM via the CompactFlash slot Appendix C Accessory Kit Assembly
8. CEE O 1 20 sO CO Ol CL o LN 5 d E T E pm Pm ul sares Ra 1 me Da 106 1270 User Manual 44 APPENDIX Watchdog Timer Programming Appendix B WDT Programming B 1 Overview The TPC 1270 cards watchdog timer can be used to monitor system soft ware operation and take corrective action if the software fails to function after the programmed period This section describes the operation of the watchdog timer and how to program it The watchdog timer is built into the super I O controller W83627HF It provides the following functions for user programming Can be enabled and disabled by user s program Timer can be set from 1 to 255 seconds or 1 to 255 minutes Generates an interrupt or resets signal if the software fails to reset the timer after time out TPC 1270 User Manual 46 B 2 Watchdog Timer Programming The I O port address of the watchdog timer is 2E hex and 2F hex 2E hex 15 the address port 2F hex is the data port You must first assign the address of register by writing address value into address port 2E hex then write read data to from the assigned register through data port 2F hex Unlock W83627 Select register of watchdog timer Enable the function of the watchdog timer Use the function of the watchdog timer Lock W83627HF Figur
9. as timeout interval Mov dx 2eh Unlock W83627HF Mov al 87h Out dx al Out dx al Mov al 07h Select registers of watchdog timer Out dx al Inc dx Mov al 08h Out dx al Dec dx Enable the function of watchdog timer Mov al 30h Out dx al Inc dx Mov al 01h Out dx al Dec dx Set second as counting unit Mov al 0f5h Out dx al Inc dx In al dx And al not 08h Out dx al Dec dx Set timeout interval as 10 seconds and start counting Mov al 0f6h 49 Chapter B Out dx al Inc dx Mov al 10 Out dx al Dec dx lock W83627HF Mov al 0aah Out dx al 2 Enable watchdog timer and set 5 minutes as timeout interval Mov dx 2eh unlock W83627H Mov al 87h Out dx al Out dx al Mov al 07h Select registers of watchdog timer Out dx al Inc dx Mov al 08h Out dx al Dec dx Enable the function of watchdog timer Mov al 30h Out dx al Inc dx Mov 1 01 Out dx al Dec dx Set minute as counting unit Mov al 0f5h TPC 1270 User Manual 50 Out dx al Inc dx In al dx Or al 08h Out dx al Dec dx Set timeout interval as 5 minutes and start counting Mov al 0f6h Out dx al Inc dx Mov al 5 Out dx al Dec dx lock W83627HF Mov al 0aah Out dx al 3 Enable watchdog timer to be reset by mouse Mov dx 2eh unlock W83627H Mov al 87h Out dx al Out dx al Mov al 07h Select registers of watchdog timer Out dx al Inc dx Mov al 08h Out dx al Dec dx Enable the function of watchdog timer
10. the directory WDT 8362x W2K XP File Edit View Favorites Tools Help Bak CJ 5 pe Search Folders Address E WwDT 8362x v Go Files Currently on the CD Step 2 Use Windows Explorer or Windows Run command to execute SETUP EXE from the companion CD ROM 29 Chapter 4 InstallShield Wizard EX Preparing to Install Advantech Watchdog Timer Drivers and Utilities for Win2000 P Setup is preparing the InstallShield Wizard which will quide you through the program setup process Please wait Configuring Windows Installer Step 3 Click Next to proceed Advantech Watchdog Timer Drivers and Utilities for Win2000 XP Install Welcome to the InstallShield Wizard for Advantech Watchdog Timer Drivers and Utilities for Win2000 XP The InstallShield Wizard will install Advantech Watchdog Timer Drivers and Utilities for Win2000 XP on your computer To continue click Next TPC 1270 User Manual 30 Step 4 Click Next to confirm the customer information Advantech Watchdog Timer Drivers and Utilities for Win2000 XP Install Customer Information Please enter your information User Name Jadvantech Install this application for Anyone who uses this computer all users Only for me tpc 1570 InstallShield Step 5 Select Advantech W83627HF Watchdog Timer and click Next Advantech Watchdog Timer Drivers and Utilit
11. Sie Keine Fl ssig oder Aerosolreiniger Am besten dient ein angefeuchtetes Tuch zur Reinigung Die NetzanschluBsteckdose soll nahe dem Ger t angebracht und leicht zug nglich sein Das Ger t ist vor Feuchtigkeit zu sch tzen Bei der Aufstellung des Ger tes ist auf sicheren Stand zu achten Ein Kippen oder Fallen k nnte Verletzungen hervorrufen Die Bel ftungs ffnungen dienen zur Luftzirkulation die das Ger t vor berhitzung sch tzt Sorgen Sie daf r daB diese ffnungen nicht abgedeckt werden Beachten Sie beim AnschluB an das Stromnetz die AnschluBw erte Verlegen Sie die NetzanschluBleitung so daB niemand dar ber fallen kann Es sollte auch nichts auf der Leitung abgestellt werden Alle Hinweise und Warnungen die sich am Ger ten befinden sind zu beachten TPC 1270 User Manual vi 11 Wird das Ger t ber einen l ngeren Zeitraum nicht benutzt sollten Sie es vom Stromnetz trennen Somit wird im Falle einer Uberspan nung eine Besch digung vermieden 12 Durch die L ftungs ffnungen d rfen niemals Gegenst nde oder Fl ssigkeiten in das Ger t gelangen Dies k nnte einen Brand bzw elektrischen Schlag ausl sen 13 ffnen Sie niemals das Ger t Das Ger t darf aus Gr nden der ele ktrischen Sicherheit nur von authorisiertem Servicepersonal ge ff net werden 14 Wenn folgende Situationen auftreten ist das Ger t vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu berpr fen a
12. and OSUnLock 3 33 HORM hr retenir res ps Serial Port Settings 42 COM 1 COM2 COM3 Connector Definition 42 ix Table of Contents A 2 Appendix B B 1 B 2 B 3 Appendix C Cl C2 Appendix D Appendix E 1 E 2 E 3 Appendix F F 1 F 2 COMA 42 WDT Programming 46 46 Watchdog Timer Programming 47 Figure B 1 Watchdog timer programming procedure 47 Table B 1 Watchdog Timer Registers 48 Example Programs Accessory Kit Assembly CompactFlash to IDE Transfer Kit 56 Figure C 1 Adapter Board and IDE Cable 56 Figure C 2 Connecting Adapter Board amp IDE Cable 56 Figure C 3 CompactFlash Slot 57 Figure C 4 Insert the Adapter Board into the CF slot 57 Figure C 5 Inserted Adapter Board 57 Figure C 6 Connect the CD ROM via the IDE Cable 58 Figure C 7 Plug Power Line into CD ROM Drive 58 USB Driver Installation Notice 58 HDD Kit Assembly 60 Figure D 1 Removing the Rear HDD Cover Figure D 2 Removing the Top Screws i Figure D 3 Installing the 11215 Figure D 4 Installing the HDD Bracket Touchscreen Installation amp Configuration 64 Driver Installation eene 64 Figure E 1 Setup exe 0 7 64 Figure E 2 Install Wi
13. C 1 CompactFlash to IDE Transfer Kit Please follow this assembly procedure to use the CompactFlash slot to connect with a CD ROM drive 1 Connect the IDE cable to the adapter board eg 22 2 7 5 33 2 TPC 1270 User Manual 56 Note Pin 1 is marked red 2 Insert the adapter board into the CompactFlash slot in Figure C 5 Inserted Adapter Board 57 Appendix C Connect the CD ROM to the adapter board via the IDE cable and then connect the external power line to the CD ROM Figure C 6 Connect the CD ROM via the IDE Cable Figure C 7 Plug Power Line into CD ROM Drive C 2 USB Driver Installation Notice It is required to install the service pack if you want to install the USB 2 0 driver on Windows XP Note Service Pack 1 must be installed on Windows XP before you install the USB 2 0 driver TPC 1270 User Manual 58 D APPENDIX HDD Kit Assembly Appendix D HDD Kit Assembly Please follow the assembly procedure to install the HDD into the system 1 Remove the rear HDD cover Figure D 1 Removing the Rear HDD Cover 2 Deassemble the HDD kit from the system Figure D 2 Removing the op Screws TPC 1270 User Manual 60 EN 3 Put the HDD into the HDD bracket and fasten the screws Figure D 3 Installing the HDD 4 Put the HDD bracket into the HDD holder Figure D 4 Installing the HDD Bracket 61 Appendix D TPC 1270 Us
14. COM LPT Sound video and game controllers System devices Universal Serial Bus controllers 19 Chapter 4 Step 1 Insert the companion CD ROM into your CD ROM drive Open the directory TPC 1270H Driver Advantech COM Step 2 Use Windows Explorer or Windows Run command to execute PCI ICOM EXE from the companion CD ROM Advantech Setup Welcome to the Advantech PCI ICOM Setup program This program will install Advantech PCI ICOM on your computer To continue click Next Step 3 Click Next to continue installation TPC 1270 User Manual 20 Advantech Setup Start Copying Files AD ANTECH Review settings before copying files AD ANTECH eAutomation Setup has enough information to start copying the program files If you want to review or change any settings click Back If you are satisfied with the settings click Next to begin copying files Current Settings System Info Extended Memory 227892 K Bootup Drive C Free Disk Space 8326MB CDROM E VIDEO XVG Colors 16777215 Date 2 23 2006 Time 15 20 33 System Windows XP InstallShield lt Back Carcel Step 4 Click Next to continue installation Advantech Setup Setup Status AD ANTECH eAutomation Advantech PCI ICOM Setup is performing the requested operations InstallShield 21 Chapter 4 Step 5 Click uninstall icon to remove PCI Serial Port L Device M
15. F RAM REG Mode In this mode any changes on C partition including modification on files or registry will be redirected to memory thus these changes will be discarded in the next system startup To exit this environment is via OSUnLock Please visit MSDN website for further information about EWF 5 3 3 HORM This is to create HORM environment Please go to Start Menu gt All Pro grams gt Advantech This utility firstly dismounts all local physical vol umes that are not protected by EWF It requires users to input the volume list Please follow the steps before running this utility to create full HORM environment Enable Hibernation via Power Options in Control Panel Make C partition EWF enabled via OSLock Make sure that all volumes to be dismounted are not in use TPC 1270 User Manual 40 APPENDIX Serial Port Settings Appendix A Serial Port Settings A 1 COM1 COM2 COM3 Connector Definition Pin Signal NDCD NRX NTX NDTR GND NDSR NRTS NCTS NRI NM oO on ND gt 2 Setting The serial port COM4 on the TPC 1270 is adjustable It can be set to RS 232 RS 422 or RS 485 This port is designed with auto data flow control capability In other word the TPC 1270 can automatically detect the data flow direction at this port when the two wired RS 485 communication is activated TPC 1270 User Manual 42 a a on 3 1 CEE eof
16. act Flash socket COM1 COM1 Serial port COM1 RS232 COM2 COM2 Serial port 2 RS232 COM3 COM3 Serial port COM3 RS232 COM4 COM4 Serial port COM4 RS232 422 485 RJ5 LAN1 ICH6M 82562EZ 10 100 RJ6 LAN2 10 100 82551QM GIGA 82541PI BT5 Battery Battery socket JP5 PCI 104 PWR Selection of PCI 104 Power JP6 RESET RESET CMOS5 CLEAR CMOS CLEAR CMOS S1 COM4 MODE1 Setting COM4 RS232 422 485 mode S2 COM4 MODE2 Setting COM4 RS422 Master or Slave mode SA5 SATA PWR D Sub 25 pin Female on panel SA6 SATA Internal IDE 44pin 2mm connector SW5 POWER System Power Switch SWITCH U58 BIOS BIOS flash socket FS5 FUSE FUSE Holder TPC 1270 User Manual 14 5 7 CN8 0 OL 915GM o ce 0 on COMB 15 Chapter 3 TPC 1270 User Manual 16 CHAPTER Software Configuration Sections include Utilities amp Drivers Advantech COM Driver Installation Watchdog Timer Driver Installation Chapter 4 Software Configuration A support CD ROM for TPC 1270 is available and along with the prod uct There are related utilities and drivers for TPC 1270 included Please install the Chipset INF driver VGA graphics driver LAN driver audio driver Advantech com driver Touchscreen driver and Watchdog Timer WDT driver sequentially 4 1 Utilities amp Drivers The following utilities and drivers are provided for TPC 1270 You can also find the updated utilities and drivers from the sup
17. anager File Action View Help 4 4 TPC 5 Computer See Disk drives Display adapters 4 DVD CD ROM drives Floppy disk controllers Sy IDE ATA ATAPI controllers gt Keyboards Mice and other pointing devices Monitors 880 Network adapters B 4p Other devices XC Port PCI Serial Port Unknown device B PCMCIA adapters Ports COM LPT Sound video and game controllers 74 System devices Universal Serial Bus controllers TPC 1270 User Manual 22 Device Manager File Action View Help TPC Computer Disk drives E Display adapters DVD CD ROM drives E Floppy disk controllers IDE ATA ATAPI controllers Keyboards g Mice and other pointing devices Monitors BB Network adapters Other devices eC Serial Port oie Unknown device PCMCIA adapters Ports COM LPT Sound video and game controllers VJ System devices Universal Serial Bus controllers Step 6 Click the scan for hardware changes icon to remove PCI Serial Port 23 Chapter4 i Device Manager File Action View 4 Computer we Disk drives a Display adapters gt DVD CD ROM drives 5 Floppy disk controllers c IDE controllers Keyboards Mice and other pointing devices 7 Monitors Network adapters lt Other devices Unknown device E PCMCIA adapters F Port
18. bility to drag on screen icons Stream mode let the mouse functions as normal and dragging on screen Point mode is only let the mouse a click function The dragging on screen is disabled Users can turn on off the beep sound by clicking the enable beep sound TPC 1270 User Manual 72 E PenMount Control Panel Figure E 15 Option 73 Appendix E TPC 1270 User Manual 74 F APPENDIX Fuse Specifications Appendix F Fuse Specifications F 1 Fuse Specifications Rating 250VAC 3 15Amp Size 5 x 20mm Note The fuse is set to break as the input voltage exceeds 33VDC for your protection F 2 Fuse Replacement Step 1 Remove the fuse cover Step 2 Replace the damaged fuse with a new one Step 3 Place the fuse cover back in position CAUTION Hot surface oe 4 Br ong Figure F1 Fuse Replacement Warning Do NOT replace the fuse unless it is damaged Do NOT replace the fuse with a different rating TPC 1270 User Manual 76
19. e B 1 Watchdog timer programming procedure 47 ChapterB Table B 1 Watchdog Timer Registers Address of Attribute Description register 2E Read Write Value 2F and description 87 hex Write this address to I O address port 2E hex twice to unlock the W83627HF 07 hex write Write 08 hex to select register of watchdog timer 30 hex write Write 01 hex to enable the function of the watchdog timer Disabled is set as default F5 hex write Set seconds or minutes as units for the timer Write 0 to bit 3 set second as counting unit default Write 1 to bit 3 set minute as counting unit F6 hex write 0 stop timer default O1 FF hex The amount of the count in seconds or minutes depends on the value set in register F5 hex This number decides how long the watchdog timer waits for strobe before gener ating an interrupt or reset signal Writing a new value to this register can reset the timer to count with the new value F7 hex rd wr Bit 6 Write 1 to enable keyboard to reset the timer 0 to disable default Bit 5 Write 1 to generate a timeout signal immediately and automati cally return to 0 default 0 Bit 4 Read status of watchdog timer 1 means timer is time out hex Write this address to I O port 2E hex to lock the watchdog timer 2 TPC 1270 User Manual 48 B 3 Example Programs 1 Enable watchdog timer and set 10 sec
20. er Manual 62 APPENDIX Touchscreen Installation amp Configuration This appedix demonstrates how to install the PenMount 9000 touchscreen and set the configuration on TPC 1260 This section uses Windows XP as an example Appendix E Touchscreen Installation amp Configuration E 1 Driver Installation Please insert the x86 TPC series support CD and go to the Windows 2000 XP driver folder TPC 1270 Driver Touch Screen Driver USB touchscreen Click setup exe setup setup Launcher pep D Installshield Software Corporation a Figure 1 Setup exe The screen displays the installation wizard for the PenMount software Click Next Follow the installation wizard step by step 27 PenMount USB InstallShield Wizard Welcome to the InstallShield Wizard for Penount USB The InstallShield R Wizard will install PenMount USB on your computer To continue click Next Next gt Cancel Figure E 2 Install Wizard TPC 1270 User Manual 64 PenMount USB InstallShield Wizard Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation IF you want to review or change any of your installation settings click Back Click Cancel ta exit the wizard Figure Install License Agreement m PenMount USB InstallShield Wizard InstallShield Wizard Completed The InstallShield Wizard has succe
21. ficated The front bezel is compliant with NEMA 4 Environment Operating Temperature 0 50 degrees Celsius Storage Temperature 20 70 degrees Celsius Humidity 10 95 40 relative humidity non condensing Vibration 1Grms 5 500Hz 3 Chapter 1 1 3 LCD Specifications Display Type TFT color LCD Size diagonal 12 1 Maximum Resolution 800 x 600 SVGA Maximum colors 262K Pixel Pitch W x 0 3075 x 0 3075 mm Viewing Angle 140 H 120 V CR gt 10 Luminance cd m 350 Contrast Ratio 500 Operating Temperature 10 65 C Ambient Backlight 2 CCFL Backlight Life Time 50 000 hours Note There might be several bright or dark pixels on the LCD This comes from the production of the LCD Such phenomenon is claimed to be normal accord ing to the LCD manufacturers TPC 1270 User Manual 4 1 4 Touchscreen Specifications Touchscreen Type Resistive Base Glass Construction Tempered Glass Resolution 1024 x 1024 Light Transmission 80 typical Controller USB Interface Power Rating 3 3 to 5V Durability 1 million touches 1 5 Power Input voltage 18 32 Vdc the fuse will be open circuit as input level exceeds 33 Vdc Typical 24V 2 5A 60W Chapter 1 1 6 I O Port Arrangement The arrangement of the I O ports is shown in Figure 1 1 A CAUTION 3 D
22. ies for Win2000 XP Install Watchdog Timer Choose the Watchdog Timer type that best suits your needs IF YOU DO NOT SURE WHAT KIND OF WATCHDOG TYPE OF YOUR BOARD IS PLEASE REFER TO THE USER S MANUAL OR CONTACT ADVANTECH TECHNICAL SUPPORT OTHERWISE THIS DRIVER MAY NOT WORKS PROPERLY Advantech Standard 443 Watchdog Timer Advantech W839774F Watchdog Timer Advantech W83627HF Watchdog Timer InstallShield 31 Chapter 4 Step 6 Click Next to confirm selecting the Typical setup type Advantech Watchdog Timer Drivers and Utilities for Win2000 XP Install X Setup Type Select the Setup Type to install Click the type of Setup you prefer then click Next Typical Program will be installed with the most common options Recommended for most users Compact Program will be installed with minimum required options Custom You may choose the options you want to install Recommended for advanced users InstallShield Ne Cancel Step 7 Click Next to proceed Advantech Watchdog Timer Drivers and Utilities for Win2000 XP Install x Start Copying Files Review settings before copying files Setup has enough information to start copying the program files If you want to review or change any settings click Back If you are satisfied with the settings click Next to begin copying files Current Settings Install this application for Anyone who
23. ling the software for E Advantech PCI Serial Port e Click Finish to close the wizard 27 Chapter4 Device Manager File Action View Help 8 ate SM Advantech ICOM Adapters V1 2 Hj Advantech PCI 1602 Series Master Bridge 88 Advantech PCI 1602 Series Slave Bridge 7 Computer Disk drives 2 Display adapters 4 DYD CD ROM drives 4 Floppy disk controllers E IDE ATA ATAPI controllers Keyboards 15 Mice and other pointing devices 9 Monitors 88 Network adapters e Other devices Unknown device 8 PCMCIA adapters dm 5 Ports COM LPT Advantech PCI Serial Port Advantech PCI Serial Port COM4 I Communications Port COM1 I Communications Port COM2 Printer Port LPT1 1 9 Sound video and game controllers System devices Universal Serial Bus controllers 4 3 Watchdog Timer WDT Driver Installation In order to ensure reliable and fail safe performance TPC 1270 has a built in Watchdog Timer to handle unexpected system failures TPC 1270 provides the drivers and a utility to activate and configure the timer for Windows XP operating systems The following is a brief introduction using XP as an example for the installation and configuration proce dures TPC 1270 User Manual 28 4 3 1 Installing the TPC 1270 Watchdog Timer Driver Step 1 Insert the companion CD ROM into your CD ROM drive Open
24. n snp res Specifications sto ec OR eier 1 2 1 System Kernel 1 22 2 niinn e HR HEINE 1 2 3 Safety and Environment 3 LCD Specifications Touchscreen Specifications ROWER ao S ROTER RETO CREER IE I O Port Arrangement Figure 1 1 I O port arrangement Panel Mounting 2 Figure 1 2 Panel Mounting Dimensions amp Cutout Figure 1 3 Dimensions eee 0 Figure 2 1 Install CompactFlash memory card 10 Figure 2 2 Power connector see 10 Figure 2 3 Power receptor and button pin assignments 11 I O Connector amp Setting Mode 14 Software Configuration 8 Utilities K Drivers tics coh mien venies 18 4 1 1 Intel Chipset Software Installation Utility 18 4 1 3 Drivers Intel R Graphics Driver 18 4 1 3 Intel PRO Network Drivers software 4 1 4 Advantech COM Driver 04 4 1 6 Watchdog Timer Driver e Advantech COM Driver Watchdog Timer WDT Driver Installation 28 4 3 1 Installing the TPC 1270 Watchdog Timer Driver 29 4 3 2 How to Use the TPC 1270 Watchdog Timer 34 Windows XP Embedded 38 J eed Advantech Utilities 5 3 1 Version Information 5 3 2 OSLock
25. n subject to misuse abuse accident or improper instal lation Advantech assumes no liability under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous test ing most of our customers never need to use our repair service If an Advantech product is defective it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem occurs 2 Call your dealer and describe the problem Please have your man ual product and any helpful information readily available 3 If your product is diagnosed as defective obtain RMA return merchandize authorization number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for war ranty service
26. often are unreliable and causes dust to circulate inside the equip ment Bright Display The bright TFT LCD display suits industrial demands for clear interfaces Powerful Communication Capability The TPC 1270 provides powerful IO interface for easily communicating with other devices The IO interface includes serial ports RS 485 port Ethernet and USB 2 0 support Embedded Windows Support In addition to the OS support of Windows XP Advantech offers platform support for XP embedded 1 2 Specifications 1 2 1 System Kernel CPU Intel Pentium M Celeron M clock rate 1 4GHz 1GHz BIOS Award 4Mbit flash memory South Bridge Intel 915GME VGA VGA Intel 915GME Ethernet TPC 1270H P1E LANI ICH6 82801FB amp 82562EZ LAN2 Intel 82541 TPC 1270H CIE LANI ICH6 82801FB amp 82562EZ LAN Intel 82551QM Watchdog timer W83627 watchdog timer 1 6 second timeout period IDE 2 EIDE channels support one IDE compact flash socket on board and one 44 pin 2mm connector TPC 1270 User Manual 2 1 2 2 I O Ports 4 Serial Ports RS 232 COMI 2 COM3 and RS 232 422 485 COM4 2 RJ 45 Ethernet port TPC 1270H PIE LAN 1 10 100BaseT LAN 2 10 100 1000BaseT TPC 1270H CIE LAN 1 10 100BaseT LAN 2 10 100BaseT 4 USB Ports Compliant with USB 2 0 1 CompactFlash Slot Typell 1 PCI 104 1VGA 2 Audio Ports 1 MIC in 1 Line out 1 2 3 Safety and Environment Safety FCC Class A and CE certificated BSMI certi
27. og Event Timer Span 15 Seconds Enable Watch Mode System Application Strobe Reboot Cancel Apply Step 4 Select the Timer Span that meets your application requirement Advantech Watchdog Service Configuration General Setting About Start watchdog service on boot Log Event Timer Span 15 Seconds m 15 Seconds 45 Seconds 4 Strobe System 1 Minute 15 Seconds Applical2 Minute 15 Seconds iiid 3 Minutes 15 Seconds Reboot Cancel Apply 35 Chapter 4 Step 5 Click Enable to enable the setting Advantech Watchdog Service Configuration General Setting About Start watchdog service on boot Log Event Timer Span 15 Seconds Enable r Watch Mode System Application Cancel Apply Step 6 Check the Start watchdog service on boot to enable the Watchdog timer to start automatically after the system boots every time Advantech Watchdog Service Configuration General Setting About Start watchdog service on boot Log Event Timer Span 15 Seconds Enable r Watch Mode System C Application Cancel Apply Step 7 Click OK then the configuration procedure is finished Note Use Advantech WDT Driver WDT was enable and WDT LED was 1Hz glisten TPC 1270 User Manual 36 CHAPTER Windows XP Embedded Sections include EWF HORM Advantech Utilities Chapter 5 Windo
28. ompact Flash memory is supposed to be hot swappable Step 3 Connect the power connector to the 24VDC power lines The power lines can either be of some power adapter or in house power source GND GND Figure 2 2 Power connector TPC 1270 User Manual 10 OFF Figure 2 3 Power receptor and button pin assignments Step 4 Plug the power lines to the system power receptor Step 5 Push the power button to power on the system as the figure 2 4 Step 6 Calibrate the touchscreen Please go to Start gt Settings gt Control Panel as the figure 2 5 Then click the tab Stylus gt Calibration gt Recalibrate to calibrate by selecting the standard calibration or advanced calibration 11 Chapter 2 TPC 1270 User Manual 12 tr A lt T 2 Connectors amp Setting Mode Chapter 3 1 0 Connector amp Setting Mode CN5 LCD POWER LCD INVERTER Connector CN6 PCI 104 PCI 104 CN7 TOUNCH Internal Touch screen Connector CN8 LVDS LCD Internal 18bit LVDS LCD Connector CN9 PWR DC IN DC Power in Connector HOUSING 5 08 MM 3P CN10 SPEAKER OUT Internal Speaker Connector CN11 USB Two USB Type A Female to on panel CN12 USB Two USB Type A Female to on panel CN13 MIC IN Audio MIC IN CN14 LINE OUT Audio Line OUT CN15 VGA D Sub 15 pin Female on panel CN16 CF Comp
29. port website 4 1 1 Intel Chipset Software Installation Utility Path TPC 1270H Driver INF English for English version TPC 1270H Driver INF Multilanguage for Multilanguage Available for the OS s below Microsoft Windows XP 4 1 2 VGA Drivers Intel R Graphics Driver Path TPC 1270H Driver VGA Available for the OS s below Microsoft Windows XP 4 1 3 Intel PRO Network Drivers software Path TPC 1270H Driver LAN Available for the OS s below Microsoft Windows XP 4 1 4 Advantech COM Driver Path TPC 1270H Driver Advantech COM Available for the OS s below Microsoft Windows XP TPC 1270 User Manual 18 4 1 5 Touchscreen Driver Path TPC 1270H Driver PenMount Available for the OS s below Microsoft Windows XP 4 1 6 Watchdog Timer Driver Path TPC 1270H Driver WDT 8362x Available for the OS s below Microsoft Windows XP 4 2 Advantech COM Driver Installation A com port named COM2 COM3 or COM4 on TPC 1270 is Advantech Special com port Please follow the steps below to install the driver i Device Manager EJE File Action View Help e 1 Computer Disk drives E Display adapters gt DVD CD ROM drives Floppy disk controllers E IDE ATA ATAPI controllers gt Keyboards 5 Mice and other pointing devices Monitors Network adapters e Other devices PCI Serial Port PCI Serial Port Unknown device PCMCIA adapters Ports
30. reasons the equipment should be opened only by qualified service personnel If one ofthe following situations arises get the equipment checked by service personnel a The power cord or plug is damaged b Liquid has penetrated into the equipment c The equipment has been exposed to moisture d The equipment does not work well or you cannot get it to work according to the user s manual e The equipment has been dropped and damaged f The equipment has obvious signs of breakage 15 DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW 20 C 4 F OR ABOVE 60 C 140 F THIS COULD DAM AGE THE EQUIPMENT THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISCARD USED BATTERIES ACCORD ING TO THE MANUFACTURER S INSTRUCTIONS The sound pressure level at the operator s position according to IEC 704 1 1982 is no more than 70 dB A DISCLAIMER This set of instructions is given according to IEC 704 1 Advantech disclaims all responsibility for the accuracy of any statements contained herein Wichtige Sicherheishinweise 1 2 3 1 Bitte lesen sie Sich diese Hinweise sorgfaltig durch Heben Sie diese Anleitung f r den sp teren Gebrauch auf Vor jedem Reinigen ist das Ger t vom Stromnetz zu trennen Ver wenden
31. s COM amp LPT Sound video and game controllers System devices Universal Serial Bus controllers FH FH FH FH Step 7 Found New Hardware and Click Next to continue installation Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for Advantech PCI 1602 Series Master Bridge If your hardware came with an installation CD or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended Install from list or specific location Advanced Click Next to continue TPC 1270 User Manual 24 Step 8 Click Finish the Advantech PCI Serial Port to continue Found New Hardware Wizard Please wait while the wizard searches E Advantech PCI Serial Port A Cancel Step 9 Then found New Hardware and Click Next to continue Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for Advantech PCI 1602 Series Slave Bridge If your hardware came with an installation CD gt or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended O Install from a list or specific location Advanced Click Next to continue Cancel 25 Chapter 4 Step 10 Click Finish the Advantech PCI 1602 Serial SlaveBridge to continue installa
32. ssfully installed PenMount USB Click Finish to exit the wizard Cancel Figure E 4 Install Completed 65 Appendix E E 2 Uninstall the Driver Please go to Settings and then select Control Panel Please click Add Remove Programs Control Panel xj Fie Edit View Favorites Tools Help Back gt search 05 GS X A Address 5 Control Panel es 5 Administrative Automatic Date Time Display Control Panel Options Hardware Add Remove Programs Tools Updates m EN c GT 31 Installs and removes programs and Windows EM Installs and removes programs and Windows components Folder Options Fonts Game Internet Keyboard Mouse Network and Controllers Options Dial up Co Windows Update Windows 2000 Support 4 a Phone and Power Options Printers Regional Scannersand Scheduled Sounds and Modem Options Cameras Tasks Multimedia System Users and Passwords Installs and removes programs and Windows components My Computer Figure E 5 Uninstall 1 Select PenMount USB Click Remove button 191 Adavantech ICOM Tools xs 078MB Advantech PCI ICOM 0 79MB 15 Macromedia Shockwave Player 942MB 2 Microsoft NET Framework 1 1 Microsoft NET Framework 1 1 Chinese Traditional Lang Pack ely 4 MSN Messenger 6 2 Hels is PenMount USB 5 33 Bib Me Snagit
33. tion Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for Advantech PCI 1602 Series Slave Bridge Click Finish to close the wizard Back Device Manager File Action View BB Advantech ICOM Adapters v1 2 Advantech PCI 1602 Series Master Bridge HE Advantech PCI 1602 Series Slave Bridge M Computer Hs Disk drives Display adapters 4 DVD CD ROM drives H E Floppy disk controllers 4 IDE controllers Keyboards a D Mice and other pointing devices Monitors Network adapters Other devices Advantech PCI Serial Port Advantech PCI Serial Port Unknown device PCMCIA adapters He sw Ports COM LPT H Sound video and game controllers System devices Lnivercal Serial Rus controllers TPC 1270 User Manual 26 Step 11 Found New Hardware and Click Next to continue installation Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for Advantech PCI Serial Port If your hardware came with an installation CD SEP or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended O Install from a list or specific location Advanced Click Next to continue Cancel Completing the Found New Hardware Wizard The wizard has finished instal
34. ultiple Monitors Option About Advanced Mode fp x v Blot calibration data Standard Elben Figure E 10 Advanced Calibration 1 69 Appendix E Touch the red square lt Figure 11 Advanced Calibration 2 D DT HET EEEEEEEES ee a 22 H f HE Touch to exit sy Li R COE i ad LE ES EE Ed d Figure E 12 Plot Calibration Data TPC 1270 User Manual 70 Note Plot Calibration Data enabled provides the blue lines to show linearity before calibration and black lines to show linearity after calibration when you finished the advanced calibration Draw This is to test the touch screen operation Its display shows touch loca tion Controtrenei STE Calibrate Draw Multiple Monitors Option About Figure E 13 Draw Click menu and then click clear screen to clear the drawing 71 Appendix E Show Pen Location 617 5 17 618 Exit 6 17 23 32 Figure 14 Clear Screen Option This option is to set the operation mode and beep sounds if the beep sound is enabled The operation mode stream mode and point mode is to enable disable the mouse s a
35. uses this computer Watchdog Type Advantech W83627HF Watchdog Timer Install Directory C Program Files Advantech Watchdog InstallShield lt Back Cancel TPC 1270 User Manual 32 Step 8 Click Finish to complete the procedure Advantech Watchdog Timer Drivers and Utilities for Win2000 XP InstallShi InstallShield Wizard Complete Setup has finished installing Advantech Watchdog Timer Drivers and Utilities for Win2000 P on your computer Step 9 Click OK to restart the system and activate the Watchdog Timer Restarting Windows Setup has finished copying files to your computer Before you can use the program you must restart your computer Select one of the following options and click OK to finish setup Yes want to restart my computer now No will restart my computer later 33 Chapter 4 4 3 2 How to Use the TPC 1270 Watchdog Timer Step 1 Open the Control Panel click Watchdog Service Configuration 2 aichdog Service Step 2 Click the Start Service button Advantech Watchdog Service Configuration General Setting About Service Name Ads Watchdog Watchdog Type Unknown Running Status Disabled Elapsed Time 00 Hour 00 Minute 00 Second Start Service TPC 1270 User Manual 34 Step 3 Click Setting to select the setting page Advantech Watchdog Service Configuration General Setting About Start watchdog service on boot L
36. ws XP Embedded TPC 1270 is in support of embedded windows platform This section is to state the important features EWF and HORN provided in windows XP embedded 5 1 EWF EWF stands for Enhanced Write Filter It provides an upper filter in the storage device driver stack that redirects disk write operations to volatile RAM or non volatile disk storage EWF protects a volume from write access The benefits are as the following Write protect one or more partitions on your system Enable read only media such as CD ROM or flash to boot and run Prolong the lifespan of write sensitive storage such as CompactFlash TPC 1270 XPE provides EWF RAM RDG mode on system partition All wirte to system partition will be redirected to RMA once this mode is enabled This mode is manually enabled by customers after they finish all their changes on system such as installing their applications or adjust ing system setting Advantech provides a pair of utilities to operate EWF OSLock and OSUnLock The setting is stated in the section later 5 2 HORM HORM stands for Hibernate Once Resume Many In HORM environ ment a single hibernation file is used to boot the system repeatedly To set a HORM environment please follow the steps below Please make sure EWF is disabled You can run OSUnLock to disable EWF Enable hibernation support Run power options in control panel and then select Enable Hiberna tion in hibernation pane
37. you call Product name and serial number Description of your peripheral attachments Description of your software operating system version appli cation software etc A complete description of the problem The exact wording of any error messages TPC 1270 User Manual iv Safety Instructions 1 25 3 Read these safety instructions carefully Keep this User s Manual for later reference Disconnect this equipment from any AC outlet before cleaning Use a damp cloth Do not use liquid or spray detergents for clean ing For plug in equipment the power outlet socket must be located near the equipment and must be easily accessible Keep this equipment away from humidity Put this equipment on a reliable surface during installation Drop ping it or letting it fall may cause damage The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before con necting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage Never pour any liquid into an opening This may cause fire or elec trical shock Never open the equipment For safety
38. zard 64 Figure E 3 Install License Agreement Figure E 4 Install Completed Uninstall the Driver Figure E 5 Uninstall 1 Figure E 6 Uninstall 2 sse Touchscreen Calibration ses Figure E 7 Standard Calibration 1 Figure E 8 Standard Calibration 2 Figure E 9 Standard Calibration 3 Figure E 10 Advanced Calibration 1 Figure E 11 Advanced Calibration 2 Figure E 12 Plot Calibration Data Figure E13 Draw i anne nee ance Figure E 14 Clear Screen Figure E 15 Option i eee Fuse Specifications esse 76 Fuse Specifications Fuse Replacement Figure F 1 Fuse Replacement 76 TPC 1270 User Manual x CHAPTER General Information Sections include Introduction Specifications LCD Specifications Touchscreen Specifications Power I O Ports Arrangement Panel Mounting Dimensions amp Cutout Chapter 1 General Information 1 1 Introduction The TPC 1270 touch panel computer is state of the art HMI Human Machine Interface This 12 1 display operator interface is an x86 based platform with these key features Fanless By using a low power processor the system does not have to rely on fans which
Download Pdf Manuals
Related Search