Home

FCC

1. VERITAS TECHNO SOURCE Technical Report 5211 210 0439 August 04 2011 Page 11 of 14 The label on these products shall be permanently affixed to the product and shall be readily visible to the purchaser at the time of purchase as described in Section 2 925 d of the FCC Part 2 Note Permanently affixed means that the label is etched engraved stamped silkscreened indelibly printed or otherwise permanently marked on a permanently attached part of the equipment or on a nameplate of metal plastic or other material fastened to the equipment by welding riveting or a permanent adhesive The label must be designed to last the expected lifetime of the equipment in the environment in which the equipment may be operated and must not be readily detachable Readily visible means that the nameplate or nameplate data must be visible from the outside of the equipment enclosure Information to User Pursuant to Section 15 21 of the Rules the users manual or instruction manual shall include the following or similar statement to caution the user Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Pursuant to Section 15 105 of the Rules the users manual or instruction manual of Class A digital devices shall include the following or similar statement placed in a prominent location in the text of the manual NOTE This equipment h
2. Page 13 of 14 The Canadian EMC Requirements If devices have been tested and comply with FCC regulation FCC Part 15 no retesting is required to show compliance with ICES 003 However additional equipment label requirement is required which must be in form of a label affixed to the device in both English and French Regulatory Statement A written notice indicating compliance must accompany each unit of digital apparatus to the end user The notice shall be in the form of a label that is affixed to the apparatus Where because of insufficient space or other constraints it is not feasible to affix a label to the apparatus the notice may be in the form of a statement included in the user s manual Suggested test for the notice indicating compliance with the standard of ICES 003 The Class digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe est conforme a la norme NMB 003 du Canada Insert either A or B but not both as appropriate for the equipment requirements END MEGA SCREEN EDITION VERITAS TECHNO SOURCE Technical Report 5211 210 0439 August 04 2011 Page 14 of 14 MEGA SCREEN EDITION
3. CONSUMER PRODUCTS SERVICES DIVISION Technical Report Date Received Sample Description Vendor Manufacturer Buyer Labeled Age Grade Appropriate Age Grade Client Specified Age Grade Tested Age Grade UPC Code Test Finished Date EXECUTIVE SUMMARY BUREAU VERITAS TECHNO SOURCE 5211 210 0439 July 27 2011 20Q ASSORTMENT SPECIALTY 1 RED 2 BLUE 3 PINK N A On File N A 6 OVER 6 YEARS OF AGE NOT SPECIFIED OVER 6 YEARS OF AGE 801561010961 801561010978 801561010985 1 AUG 2011 The sample s MEET the following requirement s Sample Size Style No s SKN SKU No PO No Ref Country of Origin Assortment No Terminal Voltage August 04 2011 Page 1 of 14 36 1096 1097 1098 N A N A N A CHINA 1095 4 50 V The tested requirements of the applicable sections of the Rules and Regulations details in 47 C F R Part 15 of the Federal Communication Commission FCC of United States of America and Industry Canada Interference Causing Equipment Standard ICES 003 LYT vh Bureau Veritas Hong Kong Limited Kowloon Bay Office 1 F Pacific Trade Centre 2 Kai Hing Road Kowloon Bay Kowloon Hong Kong Tel 852 2331 0888 Fax 852 2331 0889 www bureauveritas com cps BUREAU VERITAS HONG KONG LIMITED Law Yiu Tung Assistant Manager Electrical Department This report is governed by and incorporates by reference the Conditions of Tes
4. FCC PART 15 SECTION 15 107 Limit applicable Section 15 107 Class B Port under test AC Input Test equipment Model No EMI Test Receiver Rohde amp Schwarz ESCI Artificial Mains Network AMN Rohde amp Schwarz ESH3 Z5 Pulse Limiter Rohde amp Schwarz ESH3 Z2 Reference Ground Plane None Digital Multi meter Fluke Fluke 26 Ill Test Set up Reference Ground Plane Test method Select the AC mains supply voltage by varying the AC mains voltage over the range of 0 9 to 1 1 times the rated voltage to maximize the level of disturbance voltage measured at about 160 kHz Perform an initial measurement on each line with peak detectors to identify the frequencies where the maximum disturbances may occur Then measure and record the maximum disturbances with quasi peak and average detectors The reading on the measuring receiver is observed for about 15 s for each measurement the highest readings shall be recorded with the exception of any isolated spike which shall be ignored The final measurements shall be carried out at least at all frequencies at which there is a maximum The operational modes under test are determined according to the typical use of the EUT with respect to the expected highest level of emission During the test various parts of the EUT system are exercised in a manner permitting detection of all system disturbances BUREAU VERITAS TECHNO SOURCE Technical Report 5211 210 0439 August 04 2011 Page 9 o
5. The suggested identification label format for equipment subject to verification is illustrated as shown below Model No 123 Company s name or trade name Country of origin Country of origin U S Customs and the Federal Trade Commission regulations require all equipment produced in foreign countries to be marked with the country of origin Label of Compliance Statement Devices subject to FCC Part 15 Subpart B verification must be labeled with the statement s pursuant to Section 15 19 a of the Rules FM broadcast radio receivers or the other receivers associated with the operation of a licensed radio service shall bear the following statement in a conspicuous location on the device This device complies with Part 15 of the FCC Rules Operation is subject to the condition that this device does not cause harmful interference A stand alone cable input selector switch for cable TV shall bear the following statement in a conspicuous location on the device This device is verified to comply with Part 15 of the FCC Rules for use with cable television service All other devices shall bear the following statement in a conspicuous location on the device This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation BUREAU
6. as been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense For a Class B digital device or peripheral the user manuals or instructions shall include the following or similar statement placed in a prominent location in the text of the manual NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be deter
7. e operational mode s under test The operational modes under test are determined according to the typical use of the Equipment Under Test EUT with respect to the expected highest level of emission During the test various parts of the EUT system are exercised in a manner permitting detection of all system disturbances BUREAU VERITAS TECHNO SOURCE Technical Report 5211 210 0439 August 04 2011 Page 4 of 14 The frequency range of radiated measurements The frequency range of radiated measurements is determined pursuant to Section 15 33 For an unintentional radiator unless otherwise specified the spectrum shall be investigated from the lowest radio frequency signal generated or used in the device without going below 9 kHz up to the frequency list in the following table Highest frequency generated or used in the device or on which the device operates or tunes MHz 1 707 108 1000 Upper frequency of measurement range MHz 108 500 2000 500 1000 5000 Above 1000 5th harmonic of the highest frequency or 40 GHz which ever is lower Limits of radiated Emissions The limits of radiated emissions are specified in the appropriate Sections of the FCC rules that the EUT is subject to and the provisions in Section 15 35 Unless otherwise specified in the Rules on any frequency or frequencies below or equal to 1000 MHz the limits are based on measuring equipment employing a CISPR quasi peak detec
8. f 14 Results The test is not applicable to the product because it has no AC mains power port END of Test Data BUREAU VERITAS TECHNO SOURCE Technical Report 5211 210 0439 August 04 2011 Page 10 of 14 The General FCC Requirements in Labeling and Instruction Manual for Part 15 Devices Subject to Verification Informative The following paragraphs provide general information of labeling on most of the devices subjected to verification authorization and requirements of FCC Part 15 The responsible party i e the manufacturer or the importer within the United States shall refer to the original and updated Rules e g FCC Part 2 and Part 15 etc for acquiring information of updated or additional specific requirement for each individual device Device Identification All devices subject to verification are required to have an identification label pursuant to Section 2 954 of the Rules Additional labeling requirements may be specified in the particular sections of the FCC rules governing the specific class of equipment The label showing the equipment identification data may be combined with a label showing other information serial numbers other governments requirements etc if desired This unique identifier must be displayed on the device Under NO circumstances shall verified equipment be labeled with a FCC Identifier FCC ID or in any manner which implies that such equipment has been approved by the FCC
9. found attitude and equipment arrangement shall be used in the final measurement In frequency range of 9kHz to 30MHz a calibrated Loop antenna shall be applied for measuring radiated emissions The Loop antenna shall be positioned with its plane vertical The centre of the loop shall be 1m above ground plane and 3m apart from the EUT placed on the turntable The Loop antenna shall be rotated about its vertical axis to maximize the radiated emission measured BUREAU TECHNO SOURCE Technical Report 5211 210 0439 August 04 2011 Page 6 of 14 Results Operational mode under test On mode with Sound Light Display EUT operating condition a System Configuration The EUT system is regarded as a portable apparatus and tested as a desktop device The EUT is configured and tested as a stand alone unit b Antenna if applicable Not applicable BUREAU VERITAS TECHNO SOURCE Technical Report 5211 210 0439 August 04 201 1 Page 7 of 14 Spurious Emissions of Unintentional Radiator e Pursuant to SECTION 15 109 The measurement results are found to be more than 20dB below the permissible limit They can then be confidently regarded as having satisfied the limit requirement applied No record of measurement results is therefore required BUREAU VERITAS TECHNO SOURCE Technical Report 5211 210 0439 August 04 2011 Page 8 of 14 Conducted Emissions on AC mains port 150 kHz 30 MHz Standard
10. mined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help BUREAU VERITAS TECHNO SOURCE Technical Report 5211 210 0439 August 04 201 1 Page 12 of 14 The user manual may also be required to include other information for users if the device is subject to the provisions of any specific sections of the Rules For example TV interface devices marketed as a kit information for users pursuant to Section 15 25 shall be provided If special accessories e g shielded cables and or special connectors are required for enabling the compliance to FCC Rules they shall be explicitly specified in the user manuals or instructions pursuant to the Section 15 27 In cases where the manual is provided only in a form other than paper such as on a computer disk or over the Internet the information required by this section may be included in the manual in that alternative form provided the user can reasonably be expected to have the capability to access information in that form BUREAU VERITAS TECHNO SOURCE Technical Report 5211 210 0439 August 04 201 1
11. ral Communication Commission FCC of United States of America and Industry Canada Interference Causing Equipment Standard ICES 003 Tests Required For Unintentional Radiator Test Executed Test Requirement Test Method Limit Status Measurement of Section 15 109 Section 15 31 See Section Radiated Emissions CFR47 FCC Part 15 47 CFR FCC Part 15 15 109 ANSI C63 4 2003 CLASS B Measurement of Section 15 107 Section 15 31 See Section Conducted Emissions on CFR47 FCC Part 15 47 CFR FCC Part 15 15 107 AC Mains ANSI C63 4 2003 CLASS B N A Not Applicable BUREAU VERITAS TECHNO SOURCE Technical Report 5211 210 0439 Test Results Measurement of Radiated Emissions Requirements FCC PART 15 SECTION 15 109 Limit Section 15 109 Class B Port under test Enclosure Test equipment Open Area Test Site range 3m None Automatic Antenna Mast Automatic Turntable Antenna Mast Turntable Controller Coaxial Cable No 2 Coaxial Cable No 6 Coaxial Cable No 3 Coaxial Cable No 4 Loop Antenna Test method Location of test facilities The EMC laboratory is located at the following address August 04 2011 Page 3 of 14 No 2106 2107 21 F Westin Centre 26 Hung To Road Kwun Tong Kowloon Hong Kong The test facility has been found in compliance with the requirement of Section 2 948 of the FCC rules The information has been placed on file and listed by FCC with Registration No 642151 Th
12. t levels they can be confidently regarded as having satisfied the limit requirement applied No records of these measurement results are required For the measurements at frequencies with high ambient disturbance signals existing verification tests may be carried out in the Full Anechoic Chamber FAC as an auxiliary method to confirm whether there is any emission of radiated disturbances from the EUT If there is no maximum disturbance level from the EUT other than the corresponding intrinsic noise floor of measuring system which is at least 20 dB below the limit level then it can be stated confidently that the measurement result obtained at OATS is due to the signal levels of ambient signal sources not from the EUT BUREAU VERITAS TECHNO SOURCE Technical Report 5211 210 0439 August 04 2011 Page 5 of 14 Test Set up A Antenna Mast N Measuring Antenna Coaxial Cable 50 ohm W y m il 4 N N 3 00 p i Equipment under Test EUT Turntable Ground Plane oQ __1_ O 1 O Optical Link Optical Link Ee oso 0 S500 o A F Antenna Mast Turntable interface and Tes eit EMI Measuring Receiver GPIB Cable ES Positioning Controller With hand held or portable EUT exploratory radiated emission test shall be carried out including rotation of the EUT through three orthogonal axes to determine the attitude that highest emission relative to the limit The so
13. ting as posted at the date of issuance of this report at http www bureauveritas com cps and is intended for your exclusive use Any copying or replication of this report to or for any other person or entity or use of our name or trademark is permitted only with our prior written permission This report sets forth our findings solely with respect to the test samples identified herein The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence provided however that such notice shall be in writing and shall specifically address the issue you wish to raise A failure to raise such issue within the prescribed time shall constitute you unqualified acceptance of the completeness of this report the tests conducted and the correctness of the report contents BUREAU TECHNO SOURCE Technical Report 5211 210 0439 August 04 201 1 Page 2 of 14 SUMMARY OF TEST RESULTS The sample submitted COMPLIES with the tested requirements of the applicable sections of the Rules and Regulations detailed in 47 C F R Part 15 of the Fede
14. tor For frequencies above 1000 MHz the radiated limits are based upon the use of measurement instrument employing an average detector with a minimum resolution bandwidth of 1MHz When average radiated emission measurements are specified in Part 15 including emission measurements below 1000 MHz there also is a limit on the radio frequency emissions as measured using instrumentation with a peak detector function corresponding to 20 dB above the maximum permitted average limit unless a different peak emission limit is otherwise specified Measurement method of radiated emissions Measurements are carried out on the open area test site OATS located on the roof of the EMC laboratory in accordance with CISPR 22 as a basic standard at a measurement range of 3 meters The test site has by verification measurements satisfied the normalized site attenuation NSA requirements specified in the standard CISPR 22 For measurement at each test frequency the antenna to EUT azimuth is varied through 360 The antenna is also scanned between 1 m to 4 m in height above the ground plane to maximize the level of radiated disturbances The reading on the measuring receiver is observed for about 15 s for each final measurement the highest readings shall be recorded with the exception of any isolated spike which shall be ignored For measurements of undesired spurious emissions if the measurement results are 20 dB lower than the corresponding permissible limi

FCC

Contents

Download Pdf Manuals

Related Search

Related Contents