Stretch HDMI
Contents
1. 3 Installation Step 4 Plug the HDMI plug of the Rx side of M1 2000 into the HDMI receptacle of a TV Do NOT recommend to use any intermediate cable or adapter between them It may deteriorate the signal transmission performance Step 5 Power ON the device of a HDMI source and a TV Note M1 2000 can utilize either the 5V power supplied through a HDMI pin 18 from the HDMI source or the 5V power adaptor Nonetheless you have to confirm the power being capable to supply more than 500mA Note Do NOT worry about plugging the 5V power adaptor to the Tx module irregardless of your HDMI source supplying sufficient power through its connector since M1 2000 has a circuitry against such a power conflict Note Many HDMI sources are able to supply sufficiently DC power to two modules Just in case not being sufficient M1 2000 may require the 5V power adaptor To plug it into Tx module makes the Rx module supplied over a copper wire in the hybrid cable Figure 3 Rx Module of M1 2000 Cable Step 7 If the system does not work properly go to page 1 5 trouble shooting 1 4 Installation continued Troubleshooting The display displays only black screen Ensure that all AC and DC plugs and jacks used by external power supplies both Opticis and others are firmly connected Ensure that power bars are live Ensure that the HDMI ports are firmly plugged in to the HDMI source DVDP and TV Ensure that the Tx and Rx module parts2. Stretch HDMI User s Manual M1 2000 Manual Contents Manual Contents Welcome Product Description System Requirements for Setup Installation Troubleshooting Maintenance Technical Support Product Specifications Warranty Information Regulatory Statements Pictorials Figure 1 Optical HDMI Extension Cable M1 2000 Figure 2 Tx Module of M1 2000 Cable Figure 3 Rx Module of M1 2000 Cable 1 0 Manual Contents EE ed Se eke oe ONaAdGwHN2Sd Welcome System Requirements for Setup O Hardware requirements Congratulations on your purchase of the Stretch HDMI M1 2000 Optical HDMI High Definition Multimedia Interface Extension Cable This manual m You have to have a HDMI DVI multimedia systems DVD AV contains information that will assist you in installing and operating the product f Receiver STB etc or graphic cards It should support the Product Description maximum graphic resolution feature of TVs to be connected m Shipping Group No special requirements memory a CPU speed and 4 M1 2000 Optical HDMI Cable One 1 unit length as your inquire chipsets if youNe alteady propeny installed your POMI Systems Oo 5V AC DC power adapter One 1 unit or DVI graphic cards O User s Manual O Software requirements E No special restrictions if you ve already properly installed your HDMI DVI systems O AC DC Power Adapter Technical Advisory The M1 2000 is designed to us
3. cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Re orient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult a service representative for help Properly shielded and grounded cables and connectors must be used in order to comply with FCC CE emission limits Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment UL Statement This device has completed a UL Commercial Inspection and Testing Services for the multimode DVI cable complied with VW 1 under UL 758 It is validated by the UL file number SV2038 and project number 04CA05353 1 8 Regulatory Statements
4. e either 5V internal power supplied through a HDMI pin 18 DVI pin 14 from the graphic source port or one external 5V AC DC power adaptor to drive the Tx Rx modules To plug the power into Tx module makes the Rx module supplied over a copper wire of the hybrid cable Tips In general many HDMI sources are capable to supply sufficiently DC powers for two modules Figure 1 Optical HDMI extension Cable M1 2000 1 1 Welcome Product Description 1 2 System Requirements for Setup Installation Important Please use the installation procedure below Improper or no operation may result if the start up sequence is not correctly followed Step 1 Carefully unpack the contents of the shipping group Step 2 Plug directly the HDMI plug of the Tx side of M1 2000 into the HDMI receptacle of HDMI source DVDP or Set top Box without power up of TV and HD devices Do NOT recommend to use any intermediate cable or adapter between them It may deteriorate the signal transmission performance Step 3 As shown in Figure 2 plug the 5V power adaptor in the shipping group to the Tx module Note after having done the installing procedure and confirming the system works for your convenience you could try to deplug the power adaptor If it still works you could make sure it runs without the power adaptor If it doesn t just plug it again If you have a system hang up then got to Step 1 Figure 2 Tx Module of M1 2000 Cable 1
5. plug correctly to the HDMI source DVDP and TV respectively Check if the HDMI source DVDP and TV are powered on and properly booted Reset the system by de plugging and re plugging the Tx HDMI port or Rx HDMI port or by de plugging and re plugging the power cord plugs of Tx module Re boot up the system while connecting the optical HDMI cable system Screen is distorted or displays noises Ensure connections of both plugs while disconnecting and reconnecting the optical HDMI cables or DC power adapters Maintenance No special maintenance is required for the optical HDMI cables and power supplies Ensure that the cables and power modules are stored or used in a benign environment free from liquid or dirt contamination There are no user serviceable parts Refer all service and repair issues to Opticis Technical Support and Service For commercial or general product support contact your reseller For 1 5 Troubleshooting Maintenance Technical Support Product Specifications M1 2000 Optical HDMI Extension Cable O Compliance with HDMI standard support HDMI 1 2 and DVI 1 0 DDC2B fully implemented by fiber optic communication O Extension limit 100m 330feet for 1080p WUXGA 1 920x1 200 at 60 Hz refresh rate O Graphic Transmission Bandwidth support 1080p WUXGA at 60Hz or 1 65Gbps bandwidth per graphic channel o Hybrid Fiber optic Cable Flame retardant PVC employing 4 fiber strands and 5 shielded copper wi
6. res O Tensile load 180N E Minimum bend radius 15 4cm E Outer diameter of cable 7 2cm O Mechanical specifications of Tx and Rx module parts m Dimensions 39mm 15mm 105mm W H D E Clamping strength to cable 14kg O Environmental Specifications E Operating temperature 0 C to 50 C E Storage temperature 40 C to 70 C m Humidity 5 to 85 AC DC Power Adapter O Power Input AC 100 240V 50 60Hz 0 1A O Power Output 5 V 1 0A SMPS DC power Adapter O Cord DC Jack Core is 5 V and outer is GND 1 6 Product Specifications Warranty Information 1 One Year Warranty Opticis warrants this optical HDMI extension cable to be free from defects in workmanship and materials under normal use and service for a period of one 1 year from the date of purchase from Opticis or its authorized resellers If a product does not work as warranted during the applicable warranty period Opticis shall at its option and expense repair the defective product or part deliver to customer an equivalent product or part to replace the defective item or refund to customer the purchase price paid for the defective product All products that are replaced will become the property of Opticis Replacement products may be new or reconditioned Any replaced or repaired product or part has a ninety 90 day warranty or the reminder of the initial warranty period whichever is longer Opticis shall not be responsible for any software firm
7. ware information or memory data of customer contained in stored on or integrated with any products returned to Opticis for repair under warranty or not Warranty Limitation and Exclusion Opticis shall have no further obligation under the foregoing limited warranty if the product has been damaged due to abuse misuse neglect accident unusual physical or electrical stress unauthorized modifications tampering alterations or service other than by Opticis or its authorized agents causes other than from ordinary use or failure to properly use the Product in the application for which said Product is intended 1 7 Warranty Information FCC CE Statement This device complies with part 15 of FCC Rules and EN 55022 55024 61000 3 for CE certification Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 and 2 of FCC Rules and EN 55022 55024 61000 3 for CE certification These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction guide may
Download Pdf Manuals
Related Search