HPS 846 - Avitel
Contents
1. ELECTRONIC ADVANCE LINE HPS 846 USER MANUAL New generation CANBUS Analog Car alarm and Anti hi jack system integrated GSM pager with optional PATROLLINE remote controls September 2013 Operation with OEM remote control ALARM ARMING Push closing button of OEM remote control of the vehicle The arming will be confirmed by the followings e Blinker flashing based on closing features of the vehicle e 1 beep if it is programmed e Arming of the LED on the dashboard Activation of electric engine immobilization if it was connected Activation of module outputs optional ultrasonic sensors hyperfrequency etc CDL closes the doors ALARM DISARMING Push opening button of OEM remote control of the vehicle The disarming will be confirmed by the followings Blinker flashing based on opening features of the vehicle 2 beeps if it is programmed e Disarming of the LED on the dashboard e Deactivation of electric engine immobilizer if it was connected Deactivation of module outputs optional ultrasonic sensors hyperfrequency etc CDL opens the doors September 2013 Operation with optional PATROLLINE remote control ALARM ARMING Push Nr 3 closing button of the PATROLLINE remote control The arming will be confirmed by the followings BUTTON 1 Disarming BUTTON 2 g Siren exclusion Panic function Turn OFF the siren sound during the triggering cycle Arming Ultrasoni2. You can modify number A1 of the Principal user or you can program further 3 user numbers A2 A3 A4 Operation SMS _ command SMS reply S N x x default number of the alarm Phone number of Principal user 1234 P 36 phone number A Armed pe an Example 1234 Example i P 36201234567 S N 000123 Phone number of Principal user A Armed Within 10 minutes from receiving of the reply SMS the HPS 846 waits confirmation of the phone number modification sent in SMS from the Principal user number If the number sent in SMS is wrong you can modify it for the correct number September 2013 Armed Hps 846 Chosen car code x x code of the car set at installation Confirmation of Principal 1234 ENQ Test mode Disarmed user number Example Armed Hps 846 Chosen car code 3B Test mode Disarmed Programming of further 3 user number Operation SMS _ command SMS reply 1234 A2 36 phone number Setting changing of 1234 A3 36 phone number Numbers Stared psa te xe sehlal 2 3 or 4 user 1234 A4 36 phone number number of Barat 2 3 or 4 number Example Ai 1234 A2 36201876543 Number 2 ZArmed HpSg46 Modification of PIN code of the SMS command In the SMS commands the 1234 number is default password of the alarm which enables SMS command of the alarm This password can be modified Attention After mod
3. if each sensor will be tested the alarm will sign it with blinker flashing number of the blinker flashing shows cause of the triggering as table shows it in Alarm memory paragraph LED on the dashboard signs with flashing that the system is ready to react with acoustic optic signal for each triggering cause If the alarm signs same triggering cause five times it excludes automatically this safety function Triggering After the inhibition time the alarm will be in armed status The alarm reacts with optic acoustic signal for each triggering event it makes to operate the horn or siren and it makes to flash the blinkers Time of the triggering cycle is 30 seconds If the alarm activates triggering from same cause at 3 consecutive times the system will exclude that sensor or module which caused the triggering After it the other sensor and the engine block function if it was connected stay still active To stop the triggering without disarming of the alarm push Closing button of the OEM remote control or Nr 2 panic button of PATROLLINE remote control To stop the triggering and disarm the alarm push Opening button of the OEM remote control or Nr 1 opening button of PATROLLINE remote control Panic triggering After the inhibition time if Nr 2 panic button of PATROLLINE remote control or closing button of the OEM remote control will be pushed the alarm will trigger till 30 seconds beep acoustic signal To stop the
4. alarm 2 PIN code emergency switching OFF with usage of brake pedal hand brake this function can be used after programming of the alarm 3 PIN code emergency switching OFF on ignition key ON automatically this function can be used after programming of the alarm In boxes of the alarms can be found an envelop which contains the SECRET PIN code Only the user can open this envelop Every alarm has different PIN code We suggest for the user because of the perfect safety to change the original set PIN code for a new own one Please follow the next instructions in the followings chapters If you have got any further problem with the PIN code please look for only your importer Open only by the USER Usage of the PIN code is necessary when the remote control was lost or the battery was flat or the alarm went wrong but the device is in armed status Dependent on equipment of the cars it can be necessary to change the PIN code emergency switching OFF operation for example in that case if the vehicle is equipped with START amp GO system in this case we suggest to program the alarm for the 2 or 3 emergency switching OFF operating mode instead of the default setting of the PIN code emergency switching OFF function Only importer of PATROLLINE and his contracted partners can do the programming of the alarm because special software and hardware is necessary to it 1 PIN code emergency switching OFF with ignition key
5. as well as your vehicle safety Note Patrolline Kft 8000 Sz kesfeh rv r Kirdlysor 30 PATROLLI RJ E Tel Fax 36 22 317 367 36 22 503 078 E mail info riasztocentrum hu Web www canbusriaszto hu www patrolline eu ELECTRONIC ADVANCE September 2013
6. block paragraph the car can t be started If the alarm senses again signal of the transponder it enables starting of the vehicle At this time the transponder and LED of the alarm signs sensation of the transponder with flashing Antiagression function At turning ON of the ignition key the function activates and check presence of the transponder If the alarm doesn t sense signal of the transponder it blocks the engine according to the writing in Antiagression paragraph If the alarm senses again signal of the transponder it enables starting of the engine At this time the transponder and LED of the alarm signs sensation of the transponder with flashing Anti hi jack function In car with started engine the function activates and check presence of the transponder If the alarm doesn t sense signal of the transponder it blocks the engine according to the writing in Anti hi jack paragraph If the alarm senses again signal of the transponder it enables starting of the engine At this time the transponder and LED of the alarm signs sensation of the transponder with flashing Attention These functions are disarmed defaulty To arming of the functions please contact with the installer September 2013 Neutral time armed status After the alarm was armed with the OEM remote control or with PATROLLINE remote control the alarm will arm in the next 10 seconds what is signaled by the fix light of the dashboard LED During this time
7. function was connected Operation SMS command SMS reply The alarm stops the engine engine Activation of engine cut off YOS CAN ASK THE NECESSARY GOPE block arms and it sends the following FROM THE INSTALLER FOR WRITTEN engine block reply SMS DECLARATION Engine closed Armed The alarm makes the engine startable A YOU CAN ASK THE NECESSARY CODE 3 g Deactivation of engine cut engine block disarms and it sends FROM THE INSTALLER FOR WRITTEN off engine block the following reply SMS DECLARATION Engine closed Disarmed September 2013 Alarm maintenance Our alarms are sophisticated systems The reliability as well as time life may be furthermore incremented just adopting some precautions such as Battery changing Open box of the remote control remove the old battery and put the new Take into consideration the polarity what is located on side of the battery Use lithium battery CR 2032 in case of the optional PATROLLINE remote control Suggested the battery changing in every 2 years Vehicle cleaning should you clean the vehicle via high pressure beams hydro beam or similar please protect the siren prior to commence cleaning The alarm warranty will be cancelled if water is detected into the alarm Main maintenance All repairs must be carried at PATROLLINE assistance centers Alarm systems pampering by non authorized personnel may invalidate alarm feasibility
8. triggering push again Nr 2 panic button of PATROLLINE remote control or closing button of the OEM remote control Attention You have to activate the panic function to operate it Ask help of the installer to the activation Ultrasonic Hyperfrequency OEM shock sensor exclusion This function is necessary in order to you can leave dogs or cats in the car without triggering of the alarm In active status of the function other sensors of the alarm operate only the interior protection and the OEM shock sensor not After closing during inhibition time push closing button of the OEM or PATROLLINE remote control to disarm operation of the ultrasonic hyperfrequency OEM shock sensor The alarm signs exclusion of the ultrasonic hyperfrequence OEM shock sensor with 3 blinker flashings and 3 beeps Attention The ultrasonic hyperfrequence OEM shock sensor exclusion is valid for only one triggering cycle If you disarm the alarm with the OEM or PATROLLINE remote control the system automatically goes back to the original status and at the next arming every sensors of the alarm will operate September 2013 OEM shock sensor exclusion with optional PATROLLINE remote control This function is that the alarm doesn t trigger for vibrations concerning the car In active status of the function other sensors of the alarm operate only the OEM shock sensor not After closing during inhibition time push Nr 2 and 3 button of PATROLLINE remote c
9. 0 seconds LED of the alarm on the dashboard starts flash and it flashes till 5 seconds Till the LED flashes let off the anti hi jack button At this time the LED flashes four times slowly signed disarming of the valet function If you let off the anti hi jack button too early or too late you have to start the procedure from starting To remind activated status of the valet function the LED signs continuously with 2 flashings if you turn ON the ignition key September 2013 2 Valet function usage with ignition key this function operates even if the PIN code emergency switching OFF function is programmed for the 3 operating opportunity for the PIN code emergency switching OFF on ignition ON automatically operation Activation of the Valet function At disarmed alarm turn ON and OFF the ignition key as many time as first digit of the PIN code of the alarm During turning ON the ignition key the LED is ON and after the first digit you have to wait to switch OFF the LED After it immediately turn ON and OFF the ignition key as many time as the second digit After the LED switching OFF turn ON and OFF the ignition key as many time as the third digit The LED flashes some times signed arming of the valet function Deactivation of the Valet function Turn ON and OFF the ignition key as many time as first digit of the PIN code of the alarm During turning ON the ignition key the LED is ON and after the fir
10. c exclusion Blinker flashing if it is programmed 1 beep if it is programmed Arming of the LED on the dashboard Activation of electric engine immobilization if it was connected Activation of module outputs optional ultrasonic sensors hyperfrequency etc CDL closes the doors if it was connected ALARM DISARMING B 3 Push Nr 1 opening button of the PATROLLINE remote control UTTON 3 The disarming will be confirmed by the followings Blinker flashing if it is programmed 2 beeps if it is programmed Disarming of the LED on the dashboard Deactivation of electric engine immobilization if it was connected Deactivation of module outputs optional ultrasonic sensors hyperfrequency etc CDL opens the doors if it was connected Special functions of the optional PATROLLINE remote control HPS 846 device defaulty doesn t contain remote controls maximum 4 pieces PATROLLINE remote control can be memorized only optionally PATROLLINE remote controls use 2 4 GHz technology uniquely in Europe Thanks to this innovative technology PATROLLINE remote controls with the alarm are able for 2 ways communication Therefore it is possible that with special application of the remote control buttons the last did procedure can be controlled Unique application of the 2 ways communication provides the opportunity that different feedbacks of the remote control LED show that the connection created or not between the remote control an
11. cords one or more triggering causes after disarming of the alarm it signs the triggering causes at opening of the driver s door or at pushing of the anti hi jack pushbutton through LED of the alarm To verify type of triggering check number of flashings of the LED with the below table Nr flashing of the LED TRIGGERING CAUSE 1 DOORS OPENING WITH CAN BUS SIGNAL AND TRIGGERING BY ADDITIONAL INPUT BLUE WHITE WIRE INPUT 2 DRIVER S DOOR OPENING WITH MECHANICAL KEY WITH CAN BUS SIGNAL 3 BONNET OPENING WITH CAN BUS SIGNAL 4 TRUNK OPENING WITH CAN BUS SIGNAL 5 IGNITION PROTECTION WITH CAN BUS SIGNAL OR THROUGH THE GREEN BLACH WIRE 6 SHOCK SENSOR 7 ULTRASONIC SENSOR 8 ADDITIONAL INPUT BLUE WIRE 9 ADDITIONAL SENSOR BLUE RED WIRE INPUT 10 ADDITIONAL ALARM INPUT GREEN BLACK WIRE 11 TRIGGERING OF OEM ALARM WITH CAN BUS SIGNAL 12 RADIO OPENING SENSOR OR MOVING SENSOR 13 BONNET OPENING WITH ANALOG SIGNAL 14 GAS SENSOR 15 RADIO FREQUENCY DISTURBING PIN code The PIN code is that the user can disarm the alarm even if the remote control or the alarm go wrong or the battery discharge in the remote control PIN code emergency switching OFF function of the alarm dependent on alarm programming has 3 types operating opportunities which are the followings September 2013 BR PIN code emergency switching OFF with ignition key it is OEM setting of the
12. d the alarm LED is fix ON If each button of the remote control was used the LED of the remote control is fix ON showed that the alarm discovered the remote control September 2013 LED flashes quickly If the distance is too big between the alarm and the remote control and the alarm doesn t sense the remote control signal at pushing of each button the LED flashes quickly LED 4 slow flashings If you have to change battery in the remote control after pushing of each button the LED immediately flashes 4 With help of PATROLLINE remote control you can check that the car alarm was armed or it is in disarmed status Status of the alarm can be checked only with that PATROLLINE remote control with which the alarm was disarmed or armed latest Push Nr 1 opening and Nr 3 closing button of the remote control in same time at this time LED of the remote control signs armed or disarmed status of the alarm in big distance too from the car LED flashes quickly The alarm was armed with this PATROLLINE remote control LED is OFF The alarm was disarmed with this PATROLLINE remote control Operation of the optional PATROLLINE transponder The optional PATROLLINE transponder can be used to the following functions Passive engine block function At disarming of the alarm the function activates and check presence of the transponder If the alarm doesn t sense signal of the transponder according to the writing in Passive engine
13. ep it pushed until the procedure wasn t finished Valet function This function is that during service of the vehicle operating functions of the alarm can be suspended Usage of the valet function has independently from programming of the alarm 3 types operating opportunities which are the followings 1 Valet function with anti hi jack button 2 Valet function with ignition key 3 Valet function with usage of brake pedal hand brake this function can be used after programming of PIN code emergency switching OFF function of the alarm 1 Valet function usage with anti hi jack button Activation of the valet function At disarmed alarm sit into the car All doors of the vehicle have to be closed Turn ON the ignition key and immediately push and keep pushed anti hi jack button of the alarm what was installed into the vehicle After 10 seconds LED of the alarm on the dashboard starts flash and it flashes till 5 seconds Till the LED flashes let off the anti hi jack button At this time the LED flashes twice slowly signed arming of the valet function If you let off the anti hi jack button too early or too late you have to start the procedure from starting Deactivation of the valet function At disarmed alarm sit into the car All doors of the vehicle have to be closed Turn ON the ignition key and immediately push and keep pushed anti hi jack button of the alarm what was installed into the vehicle After 1
14. h draw of the brake pedal hand brake the LED is ON after the first digit you have to wait to switch OFF the LED After it immediately push draw the brake pedal hand brake as many time as the second digit After the LED switching OFF push draw the brake pedal hand brake as many time as the third digit If the procedure was successful the alarm disarms If the procedure was unsuccessful the alarm stays in armed status and triggers at this time you have to restart the PIN code emergency switching OFF procedure from first digit giving of the PIN code 3 PIN code emergency switching OFF on ignition key ON automatically this function can be used after programming of the alarm At armed alarm open the driver s door with mechanical key The alarm starts trigger at this time turn ON the ignition key and the transponder identifies the default key and through the CAN BUS network the alarm will be disarmed automatically ATTENTION If the Anti hi jack Antiagression function are programmed before starting of the procedure push the secret button used to the Anti hi jack Antiagression and keep it pushed until the procedure wasn t finished Modification of the PIN code Modification of the PIN code is necessary if the client wants to modify the default PIN code for a personalized PIN code Attention We suggest for the user because of the perfect safety to change the original set PIN code for a new own one To modify the PIN code d
15. ification of the password need to use the new password in every SMS commands Modification of the password is possible according to the followings Operation SMS command SMS reply 1234 PASS new password lt Changing of password Example 1234 PASS 9999 Password changed Attention The new password can be only 4 digits September 2013 Checking of the alarm status It s possible to check disarmed or armed status of the alarm from far through SMS command Operation SMS_ command SMS reply Request of alarm armed 1234 ST Status of alarm Armed or disarmed status Status of alarm Disarmed It s possible to arm and disarm the alarm through SMS according to the followings Operation SMS _ command SMS reply The alarm arms and sends the following Alarm arming 1234 ST ON reply SMS Alarm armed The alarm disarms and sends the Alarm disarming 1234 ST OFF following reply SMS Alarm disarmed Attention This function arms or disarms the CDL only if CDL command of the alarm happens through CAN BUS E g in Toyota vehicles or command wires of the CDL are connected Checking of battery level HPS 846 alarm continuously monitors the battery level considering 10 5 V set threshold When the battery level go down to this threshold the device checks the status in every 30 seconds for 5 times if nothing changes the device
16. it is default setting of the alarm The PIN code is a 3 figures number e g 1 2 3 If you would like to use the PIN code do the following instructions with ignition key of the vehicle At armed alarm open the driver s door with mechanical key The alarm starts trigger at this time turn ON the ignition key and turn OFF the ignition key as many time as first digit of the PIN code During turning ON the ignition key the LED is ON after the first digit you have to wait to switch OFF the LED After it immediately turn ON and OFF the ignition key as many time as the second digit After the LED switching OFF turn ON and OFF the ignition key as many time as the third digit If the procedure was successful the alarm disarms If the procedure was unsuccessful the alarm stays in armed status and triggers at this time you have to restart the PIN code emergency switching OFF procedure from first digit giving of the PIN code September 2013 2 PIN code emergency switching OFF with usage of brake pedal hand brake this function can be used after programming of the alarm At armed alarm open the driver s door with mechanical key The alarm starts trigger at this time turn ON the ignition key and push draw the brake pedal hand brake as many time as first digit of the PIN code the brake pedal hand brake operate with CAN BUS signals not in every car types therefore they can be used for PIN code emergency switching OFF not in every cars During pus
17. lation After programming of automatic rearming function of the alarm this function will operate with the optional PATROLLINE remote controls too according to the above mentioned Status memory If the armed alarm will be disconnected from its connector after the reconnection it stays in armed status protected the car further Passive engine block Function description if somebody tries to hijack the vehicle also with its own keys the engine can t be started the alarm gives optical signal hazard arms The passive engine block can be released with optional PATROLLINE transponder or with the secret pushbutton or with PIN code This function is disarmed defaulty To arming of the function please contact with the installer Anti hi jack function The alarm is able to immobilize the engine while the engine is ON if somebody hijacks the car This function is disarmed defaulty Arming of the function can be happened only based on request of the client with writing declaration To arming of the function please contact with the installer Antiagression function The alarm is able to immobilize the engine also in that case if somebody hijacks the car together with its own keys This function is disarmed defaulty Arming of the function can be happened only based on request of the client with writing declaration To arming of the function please contact with the installer September 2013 Alarm memory If the central unit re
18. n ON and OFF the ignition key for 3 times and within 30 seconds push the OEM remote control to close the CDL At this time the central unit will sign only with blinker flashing if triggering cause happens on the car IGNITION KEY On Off On Off On Off Push closing button of cone 000000 Dc LED OFF within 30 seconds 1 2 3 In case of usage of PATROLLINE remote control After arming of the alarm within the 10 seconds inhibition time push Nr 2 panic button of PATROLLINE remote control from this time the device signs the triggering only with blinker flashing 4 beeps and 4 blinker flashings confirm the exclusion September 2013 Attention The horn siren exclusion is valid for only one triggering cycle If you disarm the alarm with the OEM or PATROLLINE remote control the system automatically goes back to the original status and at the next arming it reacts again with beep and acoustic signals for each triggering cause Automatic rearming If the alarm was disarmed with OEM remote control of the vehicle but the doors wasn t opened within 15 seconds CDL closes back automatically the doors and in same time the alarm will be armed Attention In those cars in which there isn t automatic CDL closing back function ask the installer to program automatic rearming function of the alarm If it is programmed automatic rearming function of the alarm will operate but CDL will be closed if the alarm was connected for it at instal
19. nd push draw the brake pedal hand brake as many time as first digit of the PIN code During push draw of the brake pedal hand brake the LED is ON after the first digit you have to wait to switch OFF the LED After it immediately push draw the brake pedal hand brake as many time as the second digit After the LED switching OFF push draw the brake pedal hand brake as many time as the third digit After it the valet function will be in disarmed status September 2013 To remind activated status of the valet function the LED signs continuously with 2 flashings if you turn ON the ignition key ATTENTION If the Anti hi jack Antiagression function are programmed before starting of the procedure push the secret button used to the Anti hi jack Antiagression and keep it pushed until the procedure wasn t finished except the 1 Valet function with anti hi jack button mode Operation of HPS 846 GSM PAGER During usage of HPS 846 you can ask get warning for your phone about the extant triggerings armed disarmed status of the alarm opened status of the vehicle CDL flat of the vehicle battery with calling and or SMS In memory of the alarm 4 user phone numbers can be programmed among them the Nr 1 at programming A1 is Phone number of the Principal user Warning signals at triggering In case of triggering the system warns with calling and SMS In case of calling warning opportunities of the Principal use
20. o the following instructions with ignition key of the vehicle At disarmed alarm turn ON and OFF the ignition key as many time as first digit of the PIN code During turning ON the ignition key the LED is ON and after the first digit you have to wait to switch OFF the LED After that immediately turn ON and OFF the ignition key as many time as the second digit After the LED switching OFF turn ON and OFF the ignition key as many time as the third digit After it the LED flashes some times Turn ON and OFF the ignition key as many time as first digit of the new PIN code while the LED flashes During turning ON the ignition key the LED is ON and after the first digit you have to wait to switch OFF the LED After it immediately turn ON and OFF the ignition key as many time as second digit of the new PIN code After the LED switching OFF turn ON and OFF the ignition key as many time as third digit of the new PIN code September 2013 If the procedure was successful the LED signs it with quick flashing After it only the new PIN code can be used If PIN code function of the alarm was programmed for brake pedal hand brake mode you have to do the above procedure on same way only you have to push draw the brake pedal hand brake instead of turn ON OFF the ignition key ATTENTION If the Anti hi jack Antiagression function are programmed before starting of the procedure push the secret button used to the Anti hi jack Antiagression and ke
21. ontrol in same time to disarm the OEM shock sensor The alarm signs exclusion of the shock sensor with 5 blinker flashings and 5 beeps Attention The OEM shock sensor exclusion is valid for only one triggering cycle If you disarm the alarm with the OEM or PATROLLINE remote control the system automatically goes back to the original status and at the next arming OEM shock sensor of the alarm will operate Attention This function can be used only with the optional PATROLLINE remote control not with OEM remote control of the car Operation with optional wireless opening sensor Optional PATROLLINE wireless opening sensors can be memorized for HPS 846 device With help of them opening sensation of buildings e g garage or door of camper can be solved in near of the vehicle in which HPS 846 device is installed In case of cracking of the garage door or camper door HPS 846 alarm installed into the vehicle will trigger These sensors can be memorized in 2 safety zones of HPS 846 alarm maximum 24 pieces in zone 1 maximum 8 pieces in zone 2 Difference between the two zones is that sensors memorized in zone 2 similar to the ultrasonic can be disarmed temporarily with twice pushing of closing button of the remote controls Exclusion of horn siren With help of the OEM remote control and PATROLLINE remote control it is possible to be excluded the horn or siren function In case of usage of OEM remote control At disarmed alarm CDL opened tur
22. r Applications Hear the sounds in the car if the optional microphone was Answer to the calling installed until it hangs up Receive a SMS what contains cause of the triggering Refuse the calling Receive a SMS what contains cause of the triggering If there isn t other stored number in the alarm memory receive a SMS what contains cause of the triggering If there is other stored number the system calls this number Don t answer to the calling or isn t available the line is busy In case of triggering the system can warn further phone numbers too with calling and SMS if they were programmed Beside the Principal user number at programming A1 maximum 3 phone numbers can be programmed at programming A2 A3 A4 September 2013 In case of calling warning opportunities of the programmed Applications further users Hear the sounds in the car if the optional microphone was Answer to the calling installed until it hangs up Receive a SMS what contains cause of the triggering Refuse the calling Receive a SMS what contains cause of the triggering If there isn t other stored number in the alarm memory receive a SMS what contains cause of the triggering If there is other stored number the system calls this number Don t answer to the calling or isn t available the line is busy Modification of principal user number programming of further user numbers
23. send a SMS BATTERY LOW to A1 and A2 numbers According to the followings you can set the threshold and you can set Nr 3 4 user numbers too A3 A4 for warning of low battery level September 2013 Operation SMS _ command SMS reply A i 1234 VB set minimum value Low battery voltage warning set Setting minimum value PN minimum value V f batt It BEES O On Ine seeoE decima Battery real voltage value of the Sey Varage number write period not y g to warning of low nae battery V comma and the minimum g battery level r Example value can t be lesser than 9 Example 1234 VB 10 4 Low battery voltage warning 10 4V Battery 12 5V It s possible to program the Nr 3 and 4 numbers A3 A4 for warning of low battery level Number x Battery voltage low Armed x is position of the chosen 1234 VB x ENA user number 3 or 4 x is position of the chosen user Enable battery check in caseo usern mber number 3 or 4 Example Example 1234 VB3 ENA Number 3 Battery voltage low Armed Disarmed x is position of the chosen user number 3 or 4 case of 3 user number number 3 or 4 Example Number 3 Battery voltage low 1234 VB x DIS Disable battery check in x is position of the chosen user Example 1234 VB3 DIS Disarmed ENGINE CUT OFF from phone With help of the alarm from far you can stop block engine of the car through SMS command if the engine block
24. st digit you have to wait to switch OFF the LED After it immediately turn ON and OFF the ignition key as many time as the second digit After the LED switching OFF turn ON and OFF the ignition key as many time as the third digit After it the valet function will be in disarmed status To remind activated status of the valet function the LED signs continuously with 2 flashings if you turn ON the ignition key 3 Valet function usage with brake pedal handbrake this function operates too if the PIN code emergency switching OFF function is programmed for the 2 operating opportunity for the PIN code emergency switching OFF with usage of brake pedal hand brake operation Activation of the Valet function At disarmed alarm turn ON the ignition key and push draw the brake pedal hand brake as many time as first digit of the PIN code the brake pedal hand brake operate with CAN BUS signals not in every car types therefore they can be used for valet function not in every cars During push draw of the brake pedal hand brake the LED is ON after the first digit you have to wait to switch OFF the LED After it immediately push draw the brake pedal hand brake as many time as the second digit After the LED switching OFF push draw the brake pedal hand brake as many time as the third digit The LED flashes some times signed arming of the valet function Deactivation of the Valet function Turn ON the ignition key a
Download Pdf Manuals
Related Search