Home
JiffyDOS User`s Manual
Contents
1. 2 for each of the additional data drives Reset the default to the drive that the program will load from For example enter 8 if the program will be loaded from device 8 Load and run the program that will access the data Read write and create data files in the normal fashion from within the program After you have finished working with the program make sure that the standard interleave is reinstated on all drives refer to Step 17 in the previous procedure 24 Important points to remember about the interleave Adjusting the interleave is only effective on 1541 and 1571 drives it will not increase performance on the 1581 Adjusting the interleave will also be effective on drives that are closely compatible with the 1541 and 1571 for example FSD Bluechip Amtech Swan Excel Enhancer and Cardco drives Adjusting the interleave with drives that are not as closely compatible such as MSD and Indus drives should be approached with caution and may in fact disturb the DOS in these drives to the point where disks and data could be corrupted Files that already perform up to the maximum speed provided by JiffyDOS will not benefit from being re written using a new interleave value In fact performance with these files will most likely suffer if a different interleave value is used However if a particular program loads or accesses data two to three times slower than is possible with JiffyDOS refer to the times shown o
2. ROMs have not been changed since version 5 therefore the actual version number displayed by the drive ROM is version 5 If the stock ROM routines have been selected the message is 73 CBM DOS V2 6 1541 00 00 1571 and 1581 On 1571 and 1581 drives equipped with JiffyDOS a software switching scheme is used to select between JiffyDOS and the stock DOS With JiffyDOS installed the drives sense whether the computer they are connected to is in stock or JiffyDOS mode and subsequently select the corresponding DOS routines automatically No manual switching is required Switching ROMs with power on JiffyDOS has been designed to allow ROM switching while your system is powered on This is especially useful in cases where a heavily copy protected program will not load 12 with JiffyDOS selected but will perform high speed drive accesses properly if JiffyDOS is switched in once the program is up and running Precautions The only precaution necessary for switching ROM selections on your com puter or disk drive with power on is to be sure that no disk accesses are taking place at the time switching while a disk drive is being accessed will cause the system to hang up Take note however that switching Kernal ROM selections on your computer while run ning a program may not be 100 reliable that is the program running at the time may crash when the switch is toggled or may hang up when a device access is attempted some programs will
3. can be printed by entering the 32 QP command prior to issuing the command and after the listing has been completed output can be restored to the screen by issuing another P command Note A directory listing produced by the command can be paused or suspended at any time by using the commands described in the section titled Listing Freeze Displays the entire directory TEST The directory listing will display the file TEST if it exists on disk T All files having a T as the first letter in their filename will be displayed in the directory listing OP Lists the directory to a printer Output is then restored to the P screen Reading the Disk Drive Error Channel Direct dev Program same JiffyDOS makes it easy to find out what has happened when the error light on your disk drive starts flashing Instead of having to type in a program as you must on stock systems you can enter a single character to display the error messages output by your disk drive The command is used to read and display the disk drive error channel This is useful in determining what type of error has occurred when the red error light on the disk drive is flashing you will also be pleased to find that issuing the command will also shut off the distracting flash of the error light If is typed when the error light is not flashing the drive OK message will be displayed 00 OK 00 00 If the command is ent
4. certain disk errors are encountered Entering B will disable the head rattle If you wish to re enable the head rattle you may do so by issuing the UJ command This command does not support the default device override function Note To ensure accurate formatting B will not disable the head bump at the start of a disk NEW format Copying files The JiffyDOS file copier consists of four specialized commands that enable you to make quick convenient copies of non copy protected programs or data files See the section on using the JiffyDOS file copier for step by step procedures on how to apply these commands Set Destination Device Direct Xdev Program same The X command sets the destination drive for copying files The device number specified in the command can be that of any disk drive on the serial bus or the device number of a RAM expansion unit X10 Set the destination drive to device 10 Copy file from source to destination Direct filename filetype Program same The asterisk command copies a file to the destination drive specified in the X com mands see above The filetype specified by this command can be PRG SEQ REL or USR x TEST PRG Copies the PRG file TEST to the destination drive specified in the last X command that was issued 39 CTRL A The CTRL A command toggles the copy flag for all files in the directory listing For this command to work properly the direct
5. copier uses the standard JiffyDOS interleave or the interleave specified by the G command which enables you to maximize the performance of the files that you copy e Because the JiffyDOS copier does not rely on drive specific routines it can also be used to transfer non copy protected programs or files between any two Commodore or Commodore compatible disk drives including those that are not equipped with JiffyDOS This makes it easy to move files between 1541 1571 1581 and compatible drives The JiffyDOS file copier is compatible with Commodore s RAMDOS which makes it ideal for transferring files to and from RAM Expansion Units Files can be copied with JiffyDOS without disturbing programs currently in memory e The file copier commands can be used within BASIC programs enabling you to write your own custom copy routines The file copier can be used to change the file type of PRG SEQ and USR files Re Saving files As described in the User s Manual using a file copy utility such as the JiffyDOS file copier to re save files created by the stock DOS is one of the best ways to increase performance when using 1541 and 1571 disk drives In fact with programs or files that already load 17 quickly on a 1571 in 128 mode re saving may be the only way to obtain a discernable speed increase The following types of files can benefit from being re saved copied using the JiffyDOS file copier e Any file written under the sto
6. message will indicate if JiffyDOS is switched in 2 Start up RAMDOS as you would normally DO NOT load the DOS Wedge supplied on your RAMDOS diskette it will disable the JiffyDOS commands 3 Use the JiffyDOS commands as you would normally to access the REU Remember to avoid the JiffyDOS commands that are not compatible with RAMDOS see above 29 The limitations of RAMDOS Commodore s RAMDOS relies on software vectors to operate Since many commercial programs reset these vectors they effectively disable RAMDOS and render the REU useless Because of the design of RAMDOS and the REU JiffyDOS cannot overcome this limitation and provide increased commercial compatibility with RAMDOS So although JiffyDOS will make using your REU easier it cannot by itself extend the usefulness with commercial software Future CMD products are planned which will overcome these problems and make your REU useable with nearly all software Using JiffyDOS Commands with BASIC Whenever JiffyDOS executes a command it opens up a 255 byte buffer at the top of BASIC If you have a BASIC program in memory that takes up all or almost all of the available BASIC memory an OUT OF MEMORY error may occur when the buffer is opened If this problem occurs with a particular program you are working on or using you can do two things to overcome the memory shortage 1 If you are in direct mode enter CLR In most cases this will free up enough memory for the buff
7. possible access when the Kernal Load routine is used For SEQ REL and USR files JiffyDOS uses a compromise interleave value designed to perform well in most cases On the other hand the stock Commodore DOS uses the same interleave value for all file types Both JiffyDOS and stock interleave values for 1541 and 1571 drives are listed in table 3 The standard JiffyDOS interleave values work well in most cases However because of the many different ways that programs load and access data there are times when using a different interleave value is the only way to provide maximum performance When to adjust the interleave In general if your JiffyDOS system is already performing close to its maximum capability within a few seconds of the times shown in the performance charts in Section 2 then changing the interleave will do little to improve performance However if you notice that a particular program seems to load or access data two to three times slower than is possible with JiffyDOS then changing the interleave and resaving the program and or data files could provide the speed you are looking for Files that can benefit from a new interleave 1 Any program PRG type that is not loaded by the Kernal Load routine Instead of using the Kernal Load routine many commercial programs incorporate a loader that reads in sections of the program byte by byte 2 Any PRG data file not accessed by the Kernal Load routine Note most programs that us
8. that if you wish to use the JiffyDOS file copier to copy files to or from a 1581 partition you must use the above commands to change to the proper partition first For more information on how to create and use 1581 partitions see chapter 6 of the Commodore 1581 Users Guide Command Summary Standard DOS 5 1 Wedge Commands Read the disk drive error channel 48 ac el QN QN Q ER QS newfile file Copy a file on the same diskette Initialize the disk drive diskname ID Format NEW a diskette diskname Short NEW Disable the JiffyDOS commands newname oldname Rename a file filel file2 Scratch a file or files QUJ Reset the disk drive ev es Validate a disk Display the disk directory device Set the default device number filename Load a BASIC program filename Load and run a BASIC program filename Load an ML program filename Save a BASIC program Additional JiffyDOS Commands B QD F G QL o eP QT ex Disable the 1541 head rattle filename List a BASIC program from disk Disable the function keys Set interleave gapsize filename Lock Unlock a file Un NEW a BASIC program Toggle printer output filename List an ASCII file from disk Set Destination device number 49 x filename type Copy a file filename Load and run an ML file filename Verify a file CTRL A Toggle all files for copy CTRL D Default drive toggle CTRL P Screen d
9. the JiffyDOS system against manufacturing defects for a period of 90 days from the date of purchase During this period the Buyer may return postage prepaid the JiffyDOS system to Creative Micro Designs Inc for replacement or repair Creative Micro Designs Inc reserves the right to deny replacement or repair of any JiffyDOS system which has been damaged due to abuse or improper installation Creative Micro Designs Inc shall not be responsible for any incidental or consequential damages of any kind or nature whatsoever including lost economic opportunity or the loss of any data or information which may have resulted from the installation or use of the JiffyDOS system Creative Micro Designs Inc shall supply the JiffyDOS system configured to the latest manufacturing version available at the time of order and shall have no obligation to enhance revise or update previously sold systems in the event that improved or revised versions are offered for sale at some future date ol
10. to re enable the JiffyDOS commands This can be necessary if the commands have been previously disabled via the Q command if the Jiffy DOS Kernal has been switched in while the computer power is ON or if an applications program has altered the BASIC tokenization or execution vectors In any of these cases the JiffyDOS commands will not be available SYS 58451 Restores the use of all JiffyDOS 64 commands on a C 64 SX 64 or C 128 in 64 mode This will not restore the JiffyDOS function key definitions SYS 65137 Restores the use of all JiffyDOS 128 commands on a C 128 in 128 mode 44 Special Command Features Using the Commands in Direct and Program Modes All JiffyDOS commands may be used in BASIC direct mode and or from within BASIC programs When using the commands within programs many of the command filename strings must be enclosed in quotes For example S FILENAME is acceptible in direct mode only while S FILENAME is the required form for program mode The following are examples of using commands in program mode Be sure to check the command syntax given in the previous reference section if you are uncertain how to use a command in program mode Examples of program mode command syntax 10 x Display the directory 20 SO0 filename Scratch a file 30 9 Set the default device to 9 40 Q D filename List a BASIC program from disk 50 I Initialize the default drive Drive Specification All co
11. 28 s and virtually all drives JiffyDOS systems are available for the following computers and disk drives e C 64 e 64C e SX 64 e C 128 e C 128D e 1541 e 1541C e 1541 II e 1571 e 1581 e FSD 1 e FSD 2 e Excelerator e Excel 2001 e OC 118 e MSD 1 e MSD 2 e Enhancer 2000 e BCD 5 25 10 e BCD 128 e RF501C e RF512C e FD 168 e SW71 e Indus GT e CSD 1 JiffyDOS can be ordered for any combination of the above computers and disk drives Additional drive ROMs can be ordered if you wish to speed up second third or fourth drives JiffyDOS allows the use of multiple dissimilar drives i e 1541 1571 1581 whether or not they are equipped with JiffyDOS ROMs JiffyDOS equipped disk drives can be used interchangeably on different JiffyDOS equipped computers for example a C 64 and C 128 or with stock computers Contact Creative Micro Designs if you are interested in expanding your JiffyDOS system Compatibility Guarantee Because of our confidence in the compatibility of JiffyDOS we back our product with a 30 day Money Back Compatability Guarantee The JiffyDOS guarantee is simple If you are dissatisfied because JiffyDOS is not compatible with any of the hardware or software that you own simply return the unit unmodified and in good condition within 30 days of purchase for a complete refund This offer is only valid with units purchased directly from CMD See the back of this manual for a complete description of
12. ASIC program f7 Load an ML program f2 List a BASIC program from disk f4 List an ASCII text file from disk f6 Save a BASIC program f8 Scratch a file Using the function keys with the directory listing The JiffyDOS function key definitions have been designed to work along with the filenames in the directory listing Once the directory has been listed the cursor can be moved to the line of the desired filename the appropriate function key can be pressed and then RETURN can be pressed when it is OK to proceed with the command Using the JiffyDOS function keys with the directory listing eliminates the possibility of filename misspellings And there is no need to enter a colon after the filename or erase the filetype characters manually in order to avoid a syntax error After the function key has been pressed the filename can be altered if desired Disabling the function keys The JiffyDOS F command may be used to disable the function key definitions in 64 mode In 128 mode this command will switch the function keys from the JiffyDOS definitions to the standard 128 definitions Refer to Section 4 The JiffyDOS Commands for a complete description of the F command Re enabling the JiffyDOS function keys The following commands are used to re enable the standard JiffyDOS function key defini tions For more information see Section 4 of this manual SYS 58551 64 mode SYS 65137 128 mode Reprogrammable function keys 64 m
13. JiffyDOS User s Manual Version 6 01 Contents Introduction Getting Started 2 a Getting Help y e a Toa d dee wk ee eee de a ee ee be be ee A Installation Service 2 oaoa a a a a a What this Manual Includes o oaoa a aa a A o s s s ca arora i ee we a a he g oa aG ara a eA a aa ae 4 La ke E E EE A gs Aen ete Speen neces E ae eee ee E Compatibility 34 48 444 ace a wok ba Oe AR a e a og Be te ge a SO ee ee eee ee pina hte beta ae ee a see hae th dp tn es gen ge le ad A AA CD b Rte td ee be ee 9d ia hah dy be hey Sp ese Lede oe ih BO oe Boe Ae ba eG Sh oa eee eas ida rer er rears ers ere eh ee ES ONNE PARTIC CET TTT dia dal a er eas The JiffyDO ommands A AA A A eee dene EEE Se Ss obs IA A er ida on oe ae eae aa bee fee tee see ue oe is See A Verifying Programs Listing BASIC Programs from Disk 0 o e e Listing ASCII Files from Disk o 000000002 eee ee Un NEWing a BASIC Program o e o Initializing the Disk Drive o o e e Resetting the Disk Drivel ee opr A A A CONDO 12 12 13 13 15 16 17 21 26 28 28 29 30 A Es ee a A ge E dario iia drid A paddle sos BE seda el pi Bash de ek RA hE A A a AIN pres sed aa AS ee Ge eS Scratching Deleting Files ss 2 44 keadaee dha a oleae lees b eae aces pe a we ae wR ee A E dee a y dos e O Ei rs e Bans TE e et eo Ree e
14. MO command to the 1571 disk drive will place it in 1541 mode ensuring best performance If a Program won t Load or Operate Although we have made every effort to ensure compatibility with as much software as possible you may occasionally run across a program that will not load or operate properly with JiffyDOS Loading problems are almost always caused by extravagant copy protection schemes that rely on stock head step rates serial bus timing and particular ROM versions these copy protection schemes are the same ones that cause loading problems on 1571 and 1541C drives Unfortunately it would be necessary to reduce the performance of JiffyDOS in order to provide compatibility with these programs Another very rare type of program will load OK under JiffyDOS but will not operate properly once loaded This type of problem is caused almost exclusively by bad program ming practices i e the indiscriminate use of ROM routines without regard to normal entry points jump tables etc This misuse of ROM routines has become so widespread that Commodore is now very reluctant to change even fix or improve their own ROMs for fear of introducing compatibility problems Since JiffyDOS relies on carefully selected ROM changes to enhance performance undoing any of these alterations to provide compatibility with just one program would unfortunately reduce performance features or both What to do if a program won t load JiffyDos includes a switch whi
15. OS Commands provides a description of each JiffyDOS com mand The JiffyDOS guarantee and Warranty are included at the back of this manual What is JiffyDOS JiffyDOS is an enhanced Disk Operating System DOS for Commodore C 64 SX 64 and C 128 computers Programmed onto ROMs that replace the Kernal ROM s in your computer and the DOS ROM in your disk drive JiffyDOS provides the speed commands and convenience missing on stock systems Because it is ROM based JiffyDOS becomes an integral part of your system and is able to provide performance without the compatibility problems of Cartridges and other speed enhancement systems Features Uses no ports or cabling JiffyDOS installs without any extra cabling between your computer and disk drive s and does not tie up the Cartridge User or Cassette ports This enables compatibility with all hardware devices such as modems memory expansions etc and gives JiffyDOS an advantage over cartridge speedups and other hardware upgrades RapiDOS 1541 Flash DigiDOS Dolphin DOS which require extra cabling that plugs into one of the ports on your computer Built In DOS Wedge Commands JiffyDOS includes a complete built in implementation of the Commodore DOS 5 1 Wedge command set The DOS Wedge provides simple easy to learn commands that eliminate the need to type complicated instructions when you need to perform common disk operations such as scratching files and formatting disks The Jif
16. Output is then restored to the screen Listing ASCII Files from Disk Direct T filename Program T filename dev The most common use of the T TYPE command is to list an ASCII text file such as a wordprocessor file to the screen or to a printer When using T care should be taken to list ASCII files only otherwise the results may be unpredictable for example a BASIC program will display garbage if listed to the screen or to a printer via T The default output device for the T command is the screen To list a file to the screen enter T filename To print a listing issue the P command prior to using the T command When the printout is complete you can restore output to the screen by entering P once more Note A listing produced by the T command can be paused or suspended at any time by using the commands described in the section titled Listing Freeze QT LETTER Lists the file LETTER to the screen P Lists the file APPOINTMENTS to a printer T APPOINTMENTS Output is restored to the screen at the P completion of the command Un NEWing a BASIC Program Direct LO The JiffyDOS eo Old command can be used to recover a BASIC program that has been accidently NEWed Entering O will also recover a BASIC program lost when the computer is reset Note that the Un NEW command is only effective if no new BASIC lines have been entered since the original program was lost Initializing the Dis
17. S R U TS Input the filetype 60 IF T P THEN F PRG If file is PRG copy it as such 70 IF TS S THEN FS SEO If file is SEQ copy it as such 80 IF T R THEN xFS REL If file is REL copy it as such 90 IF TS U THEN xFS USR If file is USR copy it as such Changing the filetype of PRG SEQ and USR files The JiffyDOS file copier also enables you to change the filetype of PRG SEQ and USR files Note You cannot change a PRG SEQ or USR file into a REL file and you cannot change a REL file into any other type of file Use the following procedure to change the filetype of a PRG SEQ or USR file 1 Follow Steps 1 4 under Copying a single file 2 Cursor up to the file that you wish to change Make sure the cursor is on the left hand edge of the screen Press the asterisk x key Do not press RETURN yet 3 Stay on the same line and cursor over to the filetype PRG SEQ USR Type the new filetype that you want over the one displayed on the screen and press RETURN The file will be copied to the destination drive and will be assigned the new filetype Changing the filetype can also be done by using the JiffyDOS commands within a BASIC program See below 00 INPUT SOURCE DRIVE S Input the source drive 10 INPUT DESTINATION D Input the destination drive 120 S XD Set the source and destination 40 INPUT FILE TO CHANGE FS Input the filena
18. a files Insert the copy of the original disk into the destination drive Insert the original disk into the source drive Set the default to the destination drive Use the or CTRL D commands For example enter 9 if the destination drive is device 9 Enter the desired interleave value by using the G command For example enter G5 to set the interleave to 5 Set the default to the source drive Use the or CTRL D commands For example enter 8 if the source drive is device 8 Load the directory from the source drive by entering List the directory and then use the CTRL A and or CTRL W commands to select the program s or data file s that will be getting the new interleave see the section covering the JiffyDOS file copier for more information on the CTRL A and CTRL W commands a IMPORTANT Make sure you load the directory with the command Do not use the command Tell JiffyDOS which drive is the destination drive by using the X command For example enter X9 if the destination drive is device 9 Copy the files from the source drive to the destination drive by entering RUN 23 13 14 15 16 17 18 Test the destination disk to see if the new interleave has helped performance If the disk is a program disk load the program If it is a data disk load and run the program that will access the data and then load the data file s Time the disk accesses and see if the new inte
19. ably notice no better than a 2x speed increase with JiffyDOS Whenever possible use the INPUT instruction to read files Input will perform much better than GET especially if you read in a long string each time INPUT is executed the longer the string the better the performance Compiled BASIC i e programs compiled using Basic 64 or Blitz will perform better with JiffyDOS than uncompiled BASIC the elimonatoon of interpreter overhead is the main reason However the degree of speed increase will still depend upon how the original 26 program was written See the above paragraph for a discussion of the GET and INPUT instructions Machine language programs JiffyDOS performs best when disk accesses are handled by efficient well written machine language routines JiffyDOS performance specifications are based on results obtained us ing ML routines However not all machine language routines are efficiently written which means that the speed increases you experience using JiffyDOS can vary greatly from program to program Fragmented files Fragmented files have their data scattered across a disk in a non orderly fashion This usually occurs on disks that have had a number of files scratched or erased When a file is saved to such a disk the DOS first fills up the empty areas left by the scratched files If the file being saved is long it may be written to many of these randomly located areas When it comes
20. at this command may take some time to complete depending on the amount and size of the files located on the particular diskette Formatting Disks The N NEW command is used to format a diskette There are three versions of this command to cover long short and extended formatting of the diskette Note Using inferior media can cause errors during formatting JiffyDOS is less forgiving in this respect than the stock DOS but when a formatting error occurs it should indicate to you that the media may not be reliable Long NEW Direct N diskname ID Program N diskname ID dev 37 This version of the N command is necessary when formatting a diskette for the very first time Diskname is any name you wish to assign to the disk and can be up to 16 characters long the diskette name appears at the top of directory listings The ID can be any 2 characters and is written to the directory along with the diskname and also to all header blocks on the diskette Remember to include the comma between diskname and ID when using this form of the command Short NEW Direct N diskname Program N diskname dev This version of the N command performs a short NEW on a diskette that has already been formatted A short NEW clears the directory and BAM of an already formatted diskette and is much quicker than completely reformatting Extended NEW for 1571 from 64 mode JiffyDOS equipped 1571 drives
21. be displayed and the default device will remain unchanged 9 Sets the default drive device number to 9 if device 9 is present CTRL D The CTRL D command is used on multiple drive systems to switch the default disk drive device number for all JiffyDOS commands Pressing CTRL D holding down the CTRL key and pressing D at the same time will switch the default device assignment and display the new device number on the screen For example if device 8 is the current default CTRL D will make device 9 if present the default and display a 9 on the screen If device 9 is the current default pressing CTRL D will make device 8 the default and display an 8 on the screen CTRL D offers a much more convenient means of changing default devices than the command The CTRL D command is only available in direct mode Displaying the Directory Direct S filename Program S filename dev JiffyDOS provides a quick convenient way to display disk directories without overwriting programs stored in your computer s BASIC memory JiffyDOS directories can be easily printed suspended or ended at any time The command displays the disk directory Typing with no filename displays the entire directory followed by a colon and a filename will display the specified file in the directory listing if it exists A selective listing can be displayed by using pattern matching or wild cards as part of the filename The directory
22. ber except that the BASIC program pointers are not reset as a result of the load This avoids OUT OF MEMORY errors and also means that the BASIC program pointer is not reset to the beginning of the current program Thus this command provides a way to load ML programs from within a BASIC program without resorting to the usual contortions For example use a routine similar to the following to load a number of machine language modules 10 ML1 ML2 ML3 Load and execute machine language program Direct filename Program filename dev 34 The command loads and then runs a machine language program Typing filename is a much more convenient alternative to entering LOAD filename n 1 and then doing a SYS to start the program At the beginning of a load the command finds the starting address of the ML file and then begins execution at that addredss when the program has finished loading Note While this command will work properly with most machine language programs it will not work with programs that have entry points that differ from their load addresses Loading and Running the First Program on Disk SHIFT RUN STOP The SHIFT RUN STOP key combination can be used to load and run the first program on disk Using this command is identical to entering the BASIC commands LOAD 8 1 and RUN This provides a quick convenient way of starting up most commercial software programs In 64 mode t
23. but will not otherwise be displayed If used after scratching the number of files scratched will be displayed For example the following message indicates that two files have been scratched 01 FILES SCRATCHED 02 00 This message indicates that no files have been scratched 01 FILES SCRATCHED 00 00 Examples of using the S command S TEST Scratches the file named TEST S Scratches all files from a disk S T Scratches all files that begin with the letter T S T Scratches all files with names two characters long that have a T as the second character S BITS BYTES WORDS Scratches the files BITS BYTES and WORDS Locking and Unlocking Files Direct L filename Program L filename dev The L LOCK command locks and unlocks files Once a file has been locked it cannot be accidently scratched and is marked with a lt at the end of its directory entry i e 32 TESTFILE PRG lt The L command works as a toggle that is if L is used on an unlocked file the file will be locked If L is used on an already locked file the file will be unlocked Note The LOCK command L will not work with 1581 or MSD disk drives which are not equipped with JiffyDOS QL TESTPROGRAM Locks the file TESTPROGRAM if TESTPROGRAM is not currently locked QL TESTPROGRAM Unlocks the file TESTPROGRAM if TESTPROGRAM is currently locked 42 Directing Output to a Printer Direct QP de
24. ch will return your system to a 100 stock configuration to ensure compatibility with the few programs that do present problems Refer to ROM 28 Switching earlier in this section for information on how to switch JiffyDOS out in order to provide compatibility with problem programs Using JiffyDOS with RAM Units The JiffyDOS commands support Commodore s RAMDOS for the 1700 1750 and 1764 RAM Expansion Units in both 64 and 128 modes Please read the following information carefully before using an REU with JiffyDOS Recommended RAMDOS Versions The following versions of Commodore s RAMDOS are required for proper operation with JiffyDOS 1 64 mode RAMDOS V4 2 or higher 2 128 mode RAMDOS V4 3 or higher Using earlier RAMDOS versions will subject you to the bugs that they contain and to incompatibilities with certain JiffyDOS commands If you do not have the correct version of RAMDOS it can be obtained from Q Link a User s Group bulletin board or friend Note All versions of Commodore s RAMDOS are in the public domain JiffyDOS commands that conflict with RAMDOS The following JiffyDOS commands are incompatible with Commodore s RAMDOS and should not be used 1 Q L filename Lock a file 2 filename load and run a machine language program Starting up RAMDOS on your JiffyDOS system To use RAMDOS along with JiffyDOS do the following 1 Power up or reset your system with JiffyDOS active the power on screen
25. ck Commodore DOS e Any file originally written on a 1541 drive now used on a 1571 drive e Any file originally written on a 1571 drive now used on a 1541 drive File copier commands The following JiffyDOS commands provide you with the ability to copy files Although only four commands are involved they must be used properly in order to produce the desired results Before copying any files you should understand the function and application of each command For detailed information on each individual command see the section covering JiffyDOS commands Xdev Sets the destination drive for copying x filename type Copies filename to the destination drive CTRL A Toggles the copy flag on off for all files in the directory listing CTRL W Toggles the copy flag on off for a single file in the directory listing How to copy files with JiffyDOS The following procedures describe the steps you will need to follow when copying files with JiffyDOS Before using the JiffyDOS file copier for the first time read through the procedure carefully It is also a good idea to experiment with non valuable disks until you are sure you can make successful copies Copying a single file If you need to copy one or two files or you do not want to disturb a BASIC program currently in memory use the following procedure 1 Place the source disk in the drive that you want to copy from Place the destination disk in the drive that you want to co
26. disk drives Direct Shows the syntax of the command when used in direct mode Program Shows the syntax of the command when used in a program This syntax may usually be used in direct mode as well and in many cases must be used in order to take advantage of the default device override feature Parameters printed in italics are not literal and should be replaced with the proper infor mation when using the command Parameters printed in plain text are literal and must be included in the command A drive number may optionally be used with most drive commands This is useful when using dual drives such as the MSD 2 or Commodore 4040 To indicate a drive number 0 or 1 place the drive number just prior to the colon in the command string If using a command with quotes place the device number and colon within the quotes 31 Setting the Default Device Two commands are available for switching the JiffyDOS default device on multiple drive systems The standard DOS Wedge command and the convenient JiffyDOS CTRL D device toggle Qs Direct dev Program same The command is used in multiple drive systems to specify the default disk drive device number for all JiffyDOS commands When this command is entered an attempt is made to access the drive with the device number specified within the command If the access succeeds the specified drive becomes the new default drive If the access fails a DEVICE NOT PRESENT error will
27. e This makes it easy to design short memory efficient interactive disk housekeeping pro grams with JiffyDOS something which is not possible with the Commodore DOS Wedge which forces filenames to be hard coded into your program Example program using string variables 10 REM SCRATCH A FILE 20 S Display the directory 30 INPUT FILENAME NS Get filename 40 I Initialize the disk drive 50 S N Scratch the file 60 END Default Device Override In JiftyDOS the current default device may be overridden by specifying a device num ber at the end of each command There are two requirements for doing this First the command filename string must be in quotes as in program mode and second the de vice number must be preceded by a comma Using the default override is convenient in multiple drive systems where it eliminates the bother of having to switch the default device assignment back and forth using the or CTRL D commands each time a command 46 is sent to the secondary drive The default drive override can be used in both direct and program modes Examples S0 filename 9 Scratch a file on device 9 S 9 Display directory of device 9 10 Display device 10 error channel The device number may also be assigned to a variable as in 10 A 9 A device number 20 S A Directory of device 9 47 Addendum The Super Graphics Gold Printer Interface The Xetec Supe
28. e PRG data files do not use the Kernal Load routine to access the data in the PRG file 3 Any SEQ REL or USR file that is read by a slower than normal access routine Un fortunately many programmers do not take the time to optimize their file access code maybe because the stock Commodore DOS is so slow or use a compiled language that is inefficient to begin with like compiled BASIC As a result some commer cial programs suffer from lackluster file access performance even after JiffyDOS is installed 22 Determining the optimum interleave To determine the optimum interleave for a particular program or data file follow the procedure outlined below 1 10 11 12 First be sure that you have read the information above so that you understand which programs and files can benefit from an altered interleave You will need two disk drives so that the necessary files can be copied from the original disk to the new disk The drive you will copy from is the source drive the drive you will copy to is the destination drive Determine a starting interleave value On 1541 drives use 6 On 1571 drives use 4 Make a copy of the original disk If it is a program disk the copy should be a nibble backup fast copy or parameter copy that is an exact duplicate of the original with the same sector interleave If it is a data disk it should contain the necessary system files print drivers etc if any but no actual dat
29. e eee PE a Lara A A A E AA a ea BD e E A ge bis de E E Oke Pate eke oe Bee EN Enhancements to the DOS Wedge Command Chaidingl 0 000 eee ee String Variables ee Default Device Overtida a a a a a a a a a Addendum The Super Graphics Gold Printer Interface ooa o Using 1581 Partitions subdirectories Command Summary ompatibility Guarantee ae Pe Te ee a E a er ee ee e ee Introduction Getting Started When you first receive your JiffyDOS system you will probably be anxious to install it and to start taking advantage of the speed increases that JiffyDOS provides Before beginning however please note that installing JiffyDOS requires the partial disassembly of your computer and disk drive s While this does not require a knowledge of electronics it does require some manual dexterity to perform Read through the installation instructioons carefully before starting If you do not feel confident about installing JiffyDOS yourself refer installation to a qualified technician or take advantage of Creative Micro Design s installation service Also please be aware that installing JiffyDOS will void any factory warrenty applicable to your computer or disk drive If you are concerned about voiding your warrenty you may want to delay installing JiffyDOS until your warrenty period has expired Commodore normally warrents their equipment for a period of 90 days After you have install
30. e oldfile file2 dev The ec COPY command enables you to duplicate a file C can also be used to combine two or more text or data files into a single file Programs may not be combined in this manner Note that C will duplicate a file under a different name on the same diskette but will not copy or combine files from one diskette to another or from one drive to another AC BACKUP ORIGINAL Creates a new file named BACKUP which is an exact duplicate of the file named ORIGINAL C DATA BITS BYTES Creates a file named DATA which is the combination of the files BITS and BYTES Renaming Files Direct R newname oldname Program R newname oldname dev The R RENAME command can be used to rename a file on disk When using the R command remember that the new name for the file is entered first to the left of the sign and that the existing name of the file is entered second to the right of the sign R REPORT NOTES Renames the file NOTES as REPORT Scratching Deleting Files Direct S filel file2 Program S filel file2 dev Al The S SCRATCH command can be used to delete scratch a file or a number of files from a disk Files can be scratched one at a time by entering the exact filename or in groups by specifying filenames explicitly or by using pattern matching and or wild cards The error channel may be read at the completion of the S command by issuing the command
31. ed JiffyDOS After you have installed JiffyDOS please take the time to become familiar with this manual It describes the many commands and features of your JiffyDOS system and gives you instructions on how to use them You will also find information that will help you get the most performance out of JiffyDOS If you experience any problems when using JiffyDOS please check the manual it may provide you with the information that you need to solve the problem Getting Help If you run into any problems or have any questions about the installation or operation of JiffyDOS please feel free to contact Creative Micro Designs We will be glad to assist in any way we can Our address and phone number are listed below Creative Micro Designs Inc P O Box 789 Wilbraham MA 01095 413 525 0023 Installation Service Creative Micro Designs offers a JiffyDOS installation service If you would like us to install JiffyDOS in your computer and or disk drive please contact us for information and prices What this Manual Includes This manual gives you complete instructions on how to use your JiffyDOS system e Section 2 What is JiffyDOS describes the performance and other features of JiffyDOS e Section 3 Using JiffyDOS gives you instructions on how to enable and disable JiffyDOS how to use the JiffyDOS function keys how to control listings and how to get the most performance out of your system e Section 4 The JiffyD
32. ely few programs imitate GEOS in this regard Because of such programs JiffyDOS is forced to disable sprites on its own Commodore also does this in their 128 mode DOS When JiffyDOS has to disable sprites for each byte read or written over the serial bus data transfer slows down to the turtle like speed of stock systems this slowdown also occurs by the way with Commodore s 128 mode DOS 27 Unfortunately there is not much you can do if sprites are causing JiffyDOS to slow down unless of course you have written the offending program yourself and can change it 1571 drives If you are using a Jiffy DOS equipped 1571 drive with a C 64 SX 64 or a C 128 in 64 mode you will obtain maximum performance only if the 1571 is in 1541 mode With JiffyDos installed your 1571 can access and format both sides of a disk in 1541 mode making it unnecessary to switch to 1571 mode to benefit from the increased dual side storage This means 1 You should not use the UO gt M1 command to switch into 1571 mode when using a C 64 SX 64 or C 128 in 64 mode this will reduce performance C 64 SX 64 owners Note that the 1571 is automatically in 1541 mode upon power up 2 When switching from 128 mode to 64 mode on a C 128 use the reset switch and hold down the key Do not use the GO64 command Using GO64 will leave the 1571 in 1571 mode resulting in reduced performance in 64 mode Note If you must use the GO64 command sending the UO gt
33. er 2 Shorten the offending program or cut down on its use of arrays and variables 30 The JiffyDOS Commands JiffyDos offers the convenience of a complete built in implementation of the Commodore DOS 5 1 Wedge command set Also included are a set of additional commands that provide functions that are not accessible on stock systems or through the standard DOS Wedge All JiffyDOS commands can be entered in BASIC direct mode and or used from within BASIC programs Command Descriptions This section gives a complete description of each JiffyDOS command The commands are listed by their function along with the syntax of each form of the command Examples are provided after the command descriptions to illustrate the use of each command in its basic and optional forms If no example is given the only form of the command is as listed in the syntax line Here is a brief description Indicates a command in which the last parameter given may be repeated NOTE The maximum length of a command string is 41 characters Used to enclose information which is optional to the command syntax The brackets themselves are not part of the command filename Indicates where a filename should be placed in a command Other names are used to indicate filenames as well such as oldfile filel and backup dev Used to indicate where a device number should be placed in a command Legal device numbers are usually 4 or 5 for printers and 8 through 11 for
34. ered when the system or your disk drive has just been powered up or reset the disk drive s DOS type and version number will be displayed Loading BASIC Programs JiffyDOS provides two commands for loading BASIC programs Load a BASIC program Direct filename Program filename dev The command provides a shorthand method of loading a BASIC program Typing filename is identical to entering the BASIC command LOAD filename n where n is the default drive device number 33 Load and RUN a BASIC program Direct filename Program f filename dev The 7 command loads and runs a BASIC program Typing filename is the same as entering the BASIC commands LOAD filename n where n is the default drive device number and RUN Saving BASIC Programs Direct filename Program filename dev The JiffyDOS command saves a BASIC program Typing filename is equivalent to entering the BASIC command SAVE filename n where n is the default drive device number Loading Machine Language Programs JiffyDOS provides two powerful commands for loading machine language programs Load a machine language program Direct filename Program filename dev The command loads a machine language file without resetting any BASIC pointers Typing filename is the equivalent of entering the command LOAD filename n 1 where n is the default drive device num
35. fyDOS version of the Wedge also includes a series of enhancements that make it easier to use the commands within BASIC programs Additional JiffyDOS Commands In addition to the standard DOS Wedge JifyDOS includes a number of special commands that make using your computer even easier The JifyDOS commands all use the familiar DOS Wedge syntax and enable you to perform functions such as disabling the head rattle bump on 1541 s locking and unlocking files listing files directly from disk un NEWing BASIC programs and dumping the screen to a printer Convenience features JiffyDOS provides a full compliment of convenience features that enable you to list the directory without disturbing memory to load and run the first program on disk and to pause inspect and restart BASIC of JiffyDOS listings In addition JiffyDOS includes a full set of function key definitions that work along with the directory listing to eliminate the need to type lengthy filenames when loading saving or scratching files Does not bypass error checking All JiffyDOS operations retain the built in DOS error checking and correction routines that are a necessary part of any reliable data storage system While other speedup systems and utilities i e the ones boasting 10 second formats bypass these routines JiffyDOS provides speed without jeopardizing the integrity of your data Incorporates the latest Commodore upgrades When you purchase JiffyDOS the ROMs
36. g Maximum Performance As a general rule with 1541 1571 and compatible drives only programs and files saved with JiffyDOS will load faster than programs and files saved on stock systems or with JiffyDOS switched out In some cases re saved files can be loaded up to 3 times faster With programs or files that already load quickly with the 1571 in 128 mode re saving files may be the only way to obtain a discernable speed increase Re saving files under JiffyDOS does not alter the file s format or contents in any way it merely rearranges the data more efficiently on disk which allows JiffyDOS to find each block sector more quickly Re saved files remain compatible with stock Commodore systems Re writing files To get the maximum possible speed increase when loading files from within other programs i e wordprocessors MIDI sequencers etc start up the program load in the desired file and then re save it For example to increase the load speed of a MIDI sequencer file load your MIDI sequencing program with JiffyDOS enabled and then load the file you want to speed up into the sequencer After the file has been loaded simply save it back to disk In many cases this procedure can double the speed at which files can be loaded Another method is to use the JiffyDOS file copier to re write files See the section titled The JiffyDOS File Copier for more information Changing the Sector Interleave JiffyDOS also enables yo
37. he key may be used instead of SHIFT Verifying Programs Direct filename Program filename dev The apostrophe command verifies a file in memory against a file on disk Using this com mand provides a shorthand method of entering the BASIC command VERIFY filename n 1 where n is the default drive device number This command will work with all machine language files and with all BASIC programs that have been saved under the current BASIC environment i e a BASIC program saved on the C 64 will verify properly on a C 64 but not on a C 128 in 128 mode Listing BASIC Programs from Disk Direct D filename Program D filename dev The D DLIST command enables a BASIC program to be listed to the screen or to a printer directly from the disk without loading it into memory first The file listing can be directed to a printer by issuing the P command prior to using this command After the listing has been completed output can be restored to the screen by entering the P command once again For legible results take care to use D to list only BASIC programs Note A listing produced by the D command can be paused or suspended at any time by using the commands described in the section titled Listing Freeze D GAME A listing of the program GAME will be sent from disk to the screen 35 AP A listing of the program LOTTERY will be D LOTTERY output from disk to a printer device 4 P
38. k Drive Direct QI Program 717 dev The 1 INITIALIZE command initializes the disk drive Initialization causes the drive to read the BAM block availability map and ID from a diskette and store this information in its internal memory Initialization also clears the error channel and turns off the error LED on the drive if it is flashing At times i e after a DRIVE NOT READY error it 36 will be necessary to initialize the disk drive before it can be used to perform any further operations Remember that the I command clears the error status of the drive so if you wish to read the drive error channel after an error has occurred see the command do so before using this command Note that it is a good idea to initialize the disk drive every time you insert a diskette into the drive Resetting the Disk Drive Direct QUJ Program Q UJ dev The QUJ command is used to reset the disk drive Note that UJ may not work properly with older 1541 drives For this command to work with older 1541 s the alternate syntax U may be required Validating Disks Direct V Program V dev The ev VALIDATE command is used to free unused blocks on a diskette After a diskette has been in use for a while more blocks may be free than the BAM and directory indicate Primarily this happens when unclosed files have been scratched Using the V command will free space on a diskette available for use Note th
39. l programs Scanning a listing You can easily scan a listing by using the CTRL key Holding down CTRL will stop the listing from scrolling off the screen When you want the listing to start scrolling again release the CTRL key While you are holding down the CTRL key you can also freeze or single step the listing see below Freezing a listing To freeze a listing press CTRL S Press S while holding down the CTRL key This will stop the listing from scrolling and allow you to take your hands off the keyboard To restart the listing press any key except CTRL RUN STOP SHIFT or the key Single stepping a listing With JiffyDOS you can single step a listing Single stepping enables you to scroll through a listing one line at a time To single step first stop the listing by holding down lt CON TROL gt Then while continually holding down the CTRL key alternately press the S and 15 W keys Each time you press W a new line will appear on the screen You can restart the scrolling by releasing the CTRL key after you have pressed W Ending a listing JiffyDOS enables you to end break off any JiffyDOS or BASIC listing by pressing and holding RUN STOP You can press RUN STOP while a listing is scrolling or while it is frozen after CTRL S has been pressed Note Pressing RUN STOP will work well with BASIC and JiffyDOS listings but will not necessarily break off the listings that occur within commercial programs Gettin
40. lf can be a difficult job even if you have the programming know how Another option is to contact the software manufacturer to see if any versions of the program exist that do not incorporate the built in fastloader or if there is an easy way to disable it If you own the Mastertracks MIDI sequencer contact Creative Micro Designs to obtain a free conversion utility which disables the built in fastloader and enables JiffyDOS to take charge of disk accesses BASIC programs Programs written in BASIC will produce mixed results with JiffyDOS because of the slowness of the BASIC interpreter The interpreter spends most of its time figuring out what each instruction is and what it should do with it making disk access time insignificant when compared to this software overhead As a result the speed increases you notice when using JiffyDOS will vary according to the way the BASIC program was written JiffyDOS performs best when loading another program from within BASIC i e LOAD TEST ML 8 1 Because the entire file is accessed by a single instruction the LOAD command JiffyDOS can perform at 100 efficiency On the other hand reading a file byte by byte by means of the GET instruction is the least efficient method of accessing a file Because of the amount of software overhead involved in interpreting the GET instruction and the other instruc tions in a typical GET loop and because of the disk access characteristics of GET you will prob
41. ly locate the desired file s Next use the CTRL A and or CTRL W commands to select the files that you want to copy see below The asterisk indicates that the file will be copied a Pressing CTRL A will togle the copy flag on off for all files in the listing and then re display the entire list b Pressing CRTL W will toggle the copy flag on off for a single file The cursor must be on the same line as the file that you wish to toggle and must be to the far left of the screen Do not press RETURN when the cursor is on the same line as one of the filenames This will result in a corrupted file list and will require that you reload the directory from disk 4 Enter RUN The file copier will start working When all files have been copied the cursor will return to the screen 19 Using the file copier commands in BASIC programs The following two examples illustrate how to use the file copier commands within a BASIC program Example 1 100 8 REM Set the source drive to device 8 110 X10 REM Set the destination to device 10 120 JIFFYMON PRG REM Copy PRG file JIFFYMON 130 TAX DATA SEQ REM and SEQ file TAX DATA 140 END from drive 8 REM to drive 10 Example 2 00 INPUT SOURCE DRIVE S Input the source drive 10 INPUT DESTINATION D Input the destination drive 120 S XD Set the source and destination 40 INPUT FILENAME FS Input the filename 50 INPUT TYPE P
42. me 50 INPUT NEW TYPE P S U TS Input the new filetype 20 60 IF TS P THEN FS PRG Make it a PRG file 70 IF TS S THEN FS SEQ Make it a SEQ file 80 IF TS U THEN FS USR Make it a USR file Additional notes about the JiffyDOS file copier e Whenever you copy files using the method shown above under Copying multiple files make sure that you load the directory by using the command DO NOT use the command The CTRL A and CTRL W commands will not work properly if the directory has been loaded using e JiffyDOS cannot copy non standard files such as 1581 CBM partition files and the special USR files created by GEOS e Changing a PRG file to a SEQ or USR file will not remove the first two bytes in the file the load address Likewise changing a SEQ or USR file to a PRG file will not add two load address bytes to the beginning of the file e When JiffyDOS starts to copy a REL file there may be a significant delay up to about 40 sec while JifyDOS interrogates the source drive to determine the record size of the particular REL file While this operation is being carried out the destination drive will sit inactive Do not assume that this period of inactivity means the system has hung up e After a REL file is copied the error light will always be flashing on the source drive This does not indicate that an error has occurred during copying Se
43. mmands which perform a disk operation may specify a drive number 0 or 1 within the syntax of the command This is useful if a dual drive unit i e MSD 2 or Commodore 4040 is sharing the serial bus with a JiffyDOS system To specify the drive number insert the 0 or 1 in front of the colon in each command Examples 1 List the directory from drive 1 S0 filename Scratch a file from drive 0 When addressing 1541 and compatible drives the 0 or 1 is not required but a 0 may be used if desired 45 Enhancements to the DOS Wedge JiffyDOS offers these three major enhancements to the standard DOS Wedge command format Command Chaining In program mode the JiffyDOS commands may be chained with BASIC commands or other JiffyDOS commands within the same program line Examples 10 9 S TEST 8 Switch default to device 9 scratch a file and then switch the default back to device 8 20 QS x PRINT Display the directory print a blank line and display the error channel Note Chaining is also possible to some degree in direct mode as long as program mode syntax is used and no standard BASIC commands are intermixed with JiffyDOS commands String Variables With JiffyDOS string variables may be used as part of the standard DOS Wedge and Jiffy DOS commands This makes it possible to input disk command strings from the keyboard into a string variable and then use that variable within a command sent to the disk driv
44. n pages 5 and 6 of the User s Manual then changing the interleave could provide the increased speed you are looking for The correct interleave for a particular program or file depends upon numerous factors and must be chosen carefully In most cases a trial and error approach must be employed to find the optimum value Adjusting the interleave for a particular program or file cannot make up for grossly inefficient programming practices In other words if the software you are using is just plain slow there just isn t much that can be done to speed up disk access Even machine language programs can be written poorly enough to fall into this category Adjusting the interleave may not do much for slow running languages like BASIC A good example is a loop that reads a file one byte at a time using the GET statement Because the BASIC interpreter takes so long to execute each instruction far too much time passes between the actual reading of each byte Compiled BASIC is better but not as much as you would expect While adjusting the interleave may help speed up file access from within BASIC it will most likely not provide the maximum speed that JiffyDOS is capable of Some programs utilize custom file access routines that completely bypass the Kernal ROM GEOS and Flight Simulator II are two examples Neither JiffyDOS nor an altered interleave can help the performance of such programs Files saved under JiffyDOS using a standard or al
45. ng system used by CMD in the RAMLink RAM expansion interface Compatible with all hardware Because it does not use any ports JiffyDOS can work in conjunction with all hardware devices available for C 64 s and C 128 s including modems RAM expansions MIDI inter faces hard disk drives etc JiffyDOS systems are also compatible with all serial bus devices non JiffyDOS disk drives printers printer interfaces etc JiffyDOS can be installed on disk drives regardless of device number and devices numbers can be changed on JiffyDOS drives via software or hardware with no problems In addition JiffyDOS equipped disk drives can be used with stock C 64 and C 128 computers if necessary Uses stock disk and file formats All files written under JiffyDOS are identical to standard Commodore files Disks formatted on JiffyDOS systems are identical to those formatted on stock systems This means that you will have no problems using the disks programs and files you create with JiffyDOS on stock systems and vice versa Can be completely switched out In the event that a program will not load or operate properly with JiffyDOS this should be a rare occurance we know of only a few heavily copy protected games that will not load you can switch your system back to a completely stock version with the flip of a switch As an added advantage you can use the switching system to switch JiffyDOS in or out with power on Available for all 64 s 1
46. ode The function keys C 64 or C 128 in 64 mode can be redefined by using a BASIC program The following program redefines the keys with the strings assigned to variables F1 through F8 change these strings to the new definitions you want to assign Please note that the keys must be assigned in the order shown in line 55 f1 f3 f5 f7 f2 f4 f6 f8 and each definition must end with a CHRS 0 15 F1S S CHRS 13 CHRS 0 14 20 F2S D CHRS 0 25 F3 CHRS 0 30 F45 Q4T CHR S 0 35 F5 CHRS 0 40 F6 lt CHRS 0 45 F7S CHRS 0 50 F8S CHRS 34 S CHRS 0 55 FS FIS F3S F5S F7S E2S F4S F6S E8S 60 BUF 820 65 FOR I 1 TO LEN FS 70 POKE BUF I 1 ASC MIDS FS 1 1 NEXT I 75 POKE 176 BUF 256x INT BUF 256 80 POKE 177 INT BUF 256 POKE 155 0 The variable BUF points to the RAM area where the new definitions will be stored Address 820 is the Tape Buffer This can be changed to point to any safe RAM area except for the areas under the BASIC and Kernal ROMs Listing Freeze JiffyDOS features an enhanced listing freeze method that differs from V5 0 The listing freeze is especially helpful when you are scanning a long BASIC program or a listing pro duced by the directory D list BASIC program or T list ASCII file commands In addition the listing freeze will work from within many commercia
47. only Direct N2 diskname ID Program N2 diskname ID dev This version of the N command is used exclusively to format both sides of 1571 disks when the 1571 is in 1541 mode the stock Commodore DOS allows only one side of a diskette to be formatted in 1541 mode This command helps take advantage of the double side 1541 mode operation provided by JiffyDOS Note that the 1571 is in 1541 mode upon power up and will only switch to 1571 mode if used with a C 128 in 128 mode or if the UO gt M1 command is issued The N2 command is effective only on 1571 s equipped with JiffyDOS using this command on other drives will result in a syntax error no formatting will take place Examples N NEWDISK 00 Completely formats NEWs a diskette and assigns the name NEWDISK and the ID code 00 to the diskette N BACKUP Performs a short NEW clears the directory and BAM and assigns the name BACKUP to the diskette N2 TWOSIDE 01 Formats both sides of a 1571 disk when the 1571 is in 1541 mode Assigns the name TWOSIDE and the ID code 01 to the diskette Q N NEWDISK 00 9 Completely formats a diskette in the drive assigned as device num ber 9 with the name NEWDISK and the ID code 00 38 Disabling the 1541 Head Rattle Direct B JiffyDOS 64 only Program same JiffyDOS 64 only The B BUMP command can be used to disable the 1541 head rattle bump routine which occurs when
48. ory must first be loaded into memory using the command When you press CTRL A the copy flag for each file in the directory will be toggled and then the directory will be re listed to the screen with the new copy status for each file displayed A file marked for copying will have an asterisk next to it in the directory listing After you have marked the files that you want to copy the actual process of copying the files is started by entering the BASIC RUN command CTRL W The CTRL W command toggles the copy flag of a single file in the directory listing For this command to work properly the directory must first be loaded into memory using the command To select the file that you wish to toggle move the cursor to that file in the directory listing and press CTRL W The cursor must be kept to the leftmost edge of the screen A file marked for copying will have an asterisk x next to it in the directory listing If the directory listing is longer than one screen you can use the JiffyDOS Listing Freeze feature to easily locate the desired file s You can redisplay the entire directory listing at any time by entering the BASIC LIST command After you have marked the files that you want to copy the actual process of copying the files is started by entering the BASIC RUN command Changing the Sector Interleave JiffyDOS provides a means for adjusting the interleave intersector gap for files it writes Adjusting the sector interlea
49. py to Note No action is necessary at this point for a source or destination that is an REU 2 Use the X command to tell JiffyDOS which drive is the destination drive For example enter X9 if the destination drive is to be device 9 18 3 Use the or CTRL D commands to set the default device to the source drive For example enter 8 if the source drive is to be device 8 4 List the directory from the source drive You can enter or press fl Stop the listing press RUN STOP when you see the file s that you want to copy appear on the screen 5 Cursor up to the file that you want to copy Keep the cursor on the left side of the screen Press the asterisk key the asterisk should appear in the leftmost column on the same line as the file you want to copy 6 Press RETURN The file will be copied from the source drive to the destination drive 7 Repeat Steps 4 6 for any additional files that you want to copy Copying multiple files If you need to copy more than a few files use the following procedure 1 Follow Steps 1 3 above under Copying a single file 2 Load the directory from the source drive by entering Note This will overwrite any BASIC program currently in memory Make sure you load the directory with the command Do not use the command 3 List the directory type LIST If the directory listing is longer than one screen you can use the JiffyDOS Listing Freeze feature to easi
50. r Graphics Gold SGG printer interface introduces a few quirks into the system when using certain hardware and software For instance when using the JiffyDOS device toggle CTRL D with an SGG interface attached you will see device number 14 show up This is because the SGG responds to that device number for burst commands Do not attempt to send JiffyDOS commands to the SGG via device number 14 or a serial bus lockup will occur This interface can also cause serial communication problems when using a 1571 equipped with JiffyDOS and serial bus lockups seem to occur much more frequently We recommend sending the following commands immediately after turning on your equipment when using the SGG interface on a JiffyDOS and 1571 equipped system OPEN 15 4 15 PRINT 1 SL CLOSE15 These commands should also be sent after pressing the RESET and CLEAR buttons on the SGG at the same time Using 1581 Partitions subdirectories You may use the JiffyDOS wedge to move between partitions often called subdirectories on the 1581 disk drive The partition you wish to move to must be visible in the current directory on your 1581 or else you will have to move back to the root directory Here is the JiffyDOS syntax for moving to a 1581 partition Direct 0 name Program 0 name dev In order to move back to the root directory use the same command without a drive number and name Direct Program dev Also note
51. racter set The printer must be configured as device 4 Disabling the JiffyDOS Function Keys Direct F Program same The er FUNCTION KEY command is used to disable the JiffyDOS function key defini tions Typing F with the function keys enabled as they are upon power up will disable them In 128 mode this will cause the standard 128 function key definition to be activated The JiffyDOS function key definitions are active only in BASIC direct mode and are dis abled when programs are run in order to avoid conflict with any program defined function key assignments 43 Re Enabling the JiffyDOS Function Keys SYS 58551 JiffyDOS 64 SYS 65137 JiffyDOS 128 The SYS commands are used to re enable the JiffyDOS function key assignments This can be necessary if the commands have been previously disabled via the F command or after a program has been run SYS 58551 Will restore the JiffyDOS 64 function keys and commands on a C 64 SX 64 or C 128 in 64 mode SYS 65137 Will restore the JiffyDOS 128 function keys on a C 128 in 128 mode Disabling the JiffyDOS Commands Direct QQ Program same The Q QUIT command disables all JiffyDOS commands and function key definitions and reinstates all stock BASIC vectors The disk drive fast access routines are not disabled however and will continue to operate at full speed Re Enabling the JiffyDOS Commands SYS 58451 JiffyDOS 64 SYS 65137 JiffyDOS 128 These SYS commands are used
52. respond better than others Switching to the Stock Kernal while in BASIC To switch from the JiffyDOS Kernal to the stock Kernal while your computer is in BASIC direct mode first disable the JiffyDOS commands by using the Q command and then flip the Kernal Selector Switch to the stock position Switching to the JiffyDOS Kernal while in BASIC To switch from the stock Kernal to the JiffyDOS Kernal while your computer is in BASIC direct mode first flip the Kernal Selector Switch to the JifyDOS position and then type in one of the following commands SYS 58551 64 mode SYS 65137 128 mode Using a Tape Drive with JiffyDOS It is not possible to use a tape drive Commodore DATASETTE etc while the JiffyDOS Kernal is selected If tape access is attempted an ILLEGAL DEVICE NUMBER ERROR will occur To use a tape drive with JiffyDOS select the stock Commodore Kernal ROM routines first by using the Kernal Selector Switch See ROM Switching earlier in this section for instructions Function Key Definitions JiffyDOS offers the convenience of function keys defined with JiffyDOS Wedge commands and BASIC keywords The function key definitions are active only in BASIC direct mode and are automatically disabled when a BASIC or ML program is run in order to avoid conflict with any program defined function key assignments The JiffyDOS function key definitions are fl Display the directory f3 Load a BASIC program 13 f5 Load and run a B
53. rleave has helped Keep a record of the results Return to step 5 and increase the interleave value by one Continue this procedure until you have tried all interleave values up to and including 16 Compare the timing results you recorded in step 13 to determine the interleave value that provides the best performance Re Copy the program s or data file s using the optimum interleave value Follow Steps 5 through 12 Before continuing make sure the standard interleave is reinstated on all drives The safest way to do this is to completely reset your system C64 users should power down then up C 128 users can press the reset button Carefully read the following procedure concerning data files that require an altered interleave Data files which require an altered interleave Each time you are planning to work with data files that require an altered interleave follow the prcedure below 1 Before loading and running the program that will access or create the data file s set the default to the drive that will contain the data disk Use the or CTRL D commands For example enter 9 if the data drive is device 9 Set the interleave to the optimum value for the particular program For example enter G9 if the optimum value is 9 Remember do this for 1541 and 1571 drives only altering the interleave on 1581 drives will have no effect on performance If more than one drive will be accessing the data Repeat Steps 1 and
54. tem Refer to Section 3 for more information on these factors and for ways to obtain maximum performance when using JifyDOS Compatibility Works with virtually all software We designed JiffyDOS to be fast but not at the expense of compatibility As a result JiffyDOS will load and operate with virtually all software of every type including copy protected commercial programs This includes programs that cannot be loaded by other speedup products such as cartridges software based turbo loaders and other hardware based systems In addition JiffyDOS is compatible with programs that utilize their own fast access routines such as GEOS and will work with the non standard file formats created by programs such as the VORPAL utility kit Table 2 C 128 in 128 Mode 1541 1571 1581 Disk Operation Stock JiffyDOS Stock JiffyDOS Stock JiffyDOS Load 202 block program PRG file 124 12 14 9 12 8 Save 100 block program PRG file 75 24 48 25 26 14 Read 125 block SEQ or USR file 84 15 31 12 20 10 Write 100 block SEQ or USR file 81 27 48 33 20 11 Read 64 154 byte REL records 40 14 21 14 17 10 Autoboot 202 block program 125 13 54 10 13 9 Read Write 16K on command channel 47 10 10 6 10 6 RAMDOS compatibility JiffyDOS commands are compatible with Commodore s RAMDOS for the 1700 1750 and 1764 RAM expansion units REU s as well as being compatible with the RAM operati
55. tered interleave will most likely load slower on stock systems Be careful if you have both 1541 and 1571 drives The optimum interleave for a 1571 drive may cause severely decreased performance on a 1541 drive 1571 s can read data much faster than 1541 s If you have disks that will be used on both 1541 and 1571 drives then use the optimum interleave for the slower 1541 drive 25 If you re not getting top Performance When using certain programs you may feel that JiffyDOS is not increasing performance as much as it should be In these cases the problem is most likely related to the particular software in use There are also some considerations to note when using the 1571 drives Programs with built in fast loaders Some programs utilize their own built in fast loaders Some examples are GEOS the Mastertracks MIDI sequencer Fast Hack Em and disks created by certain types of freezer cartridges These programs contain their own DOS which bypasses the disk access routines in the Kernal and DOS ROMs Since JiffyDOS resides in these ROMs any program which bypasses the disk access routines renders JiffyDOS ineffective As a result JiffyDOS can provide little if any performance gains with such programs In these cases better performance may be achieved only by altering the software so that it uses the disk access routines provided in the Kernal ROM or to alter the interleave as outlined previously Altering the software itse
56. the JiffyDOS Guarantee 11 Using JiffyDOS ROM Switching JiffyDOS enables your computer and disk drive s to be switched back to stock mode if necessary You will probably be able to have JiffyDOS selected all of the time However in rare cases your system may have to be switched back to stock mode to allow a program to load or operate properly C 64 SX 64 and C 128 The normal procedure for switching Kernal selections on the C 64 SX 64 and C 128 is to first turn your computer OFF flip the selector switch to the desired position and then power the computer back ON After your computer is powered back on the sign on screen will indicate which Kernal has been selected If the JiffyDOS Kernal is selected the sign on screen will read JiffyDOS V6 01 C 1989 CMD This may differ slightly if your version of JiffyDOS is not version 6 01 If the stock Kernal routines have been selected the normal BASIC sign on screen will be displayed 1541 and compatibles The normal procedure for switching JiffyDOS in or out on 1541 and compatible drives is to power the drive off set the selector switch to the desired position and then power the drive back ON Note The SX 64 does not have a seperate drive selector switch Reading the disk drive error channel immediately after power up will indicate which ROM selection has been made If JiffyDOS has been selected the message is 73 JiffyDOS 5 0 1541 00 00 Note The JiffyDOS version 6 drive
57. the disk access routines built into the Kernal ROM Speeds up access of SEQ REL amp USR files Another important feature of JiffyDOS is its ability to speed up the access of all types of files Program PRG Sequential SEQ Relative REL and User USR files can all be accessed faster on JiffyDOS systems This makes JiffyDOS effective with software that uses these file types and provides an advantage over cartridge speedup products which improve performance only with PRG files Table 1 C 64 SX 64 C 128 in 64 Mode 1541 1571 1581 Disk Operation Stock JiffyDOS Stock JiffyDOS Stock JiffyDOS Load 202 block program PRG file 124 12 124 9 102 8 Save 100 block program PRG file 75 24 75 20 40 15 Read 125 block SEQ or USR file 84 15 84 13 63 9 Write 100 block SEQ or USR file 81 27 81 24 44 17 Read 64 154 byte REL records 40 14 40 14 37 10 Write one 154 byte REL records 390 125 390 120 325 110 Read Write 16K on command channel 47 9 47 9 47 9 Speed comparisons Tables 1 and 2 illustrate the speed increases that can be obtained with JiffyDOS Please note that the times shown are rounded off to the nearest second and do not take into account the disk spin up delay approx 1 2 second and the time required for directory searching which varies in relation to the size of the particular directory Other factors may also influence the results that you obtain on your sys
58. time to read the file the DOS is forced to search across a wide area of the disk in order to retrieve all the data which can add significantly to the amount of time it takes to read the file To eliminate file fragmentation copy the files from the fragmented disk to an empty disk You can transfer the files using the JiffyDOS file copier or a file copy program See Getting Maximum Performance earlier in this section for more information Sprites Sprites are graphic display items that can be moved around quickly and easily on the screen Although sprites are used primarily in games Pac Man is a sprite they are also found in other types of programs the GEOS pointer is also a sprite While it seems unlikely that a screen graphic could affect disk access performance sprites present a real problem for serial bus communications routines Sprites are hardware generated by the VIC II chip and displaying them requires the VIC II to steal cycles from the 6510 8510 microprocessor Cycle stealing makes it impossible to use high speed software timing loops to transfer data over the serial bus JiffyDOS uses timing loops Even the stock Com modore C 64 is prone to hang up when sprites are displayed during serial I O The solution to the problem is to disable sprites shut them off whenever serial bus communications are taking place This is the approach used by GEOS you ll notice the pointer disappear during disk accesses Unfortunat
59. tting the Sector Interleave As mentioned earlier JiffyDOS enables you to optimize performance with some software through changing the sector interleave The G command is used to ease selection of the required interleave For specific information on the G command see the section covering JifyDOS commands Understanding sector interleave Each time the DOS writes a file to disk it uses a sector interleave value to lay out the physical distance number of sectors skipped between consecutive sectors blocks of a file After a file is written its interleave can greatly affect the speed at which the file can be read If the space between consecutive sectors the interleave is too small the DOS cannot read the next block in the file without having to wait for the disk to spin one additional revolution one disk revolution takes 0 2 seconds If the interleave is larger that it has to be the DOS also spends unnecessary idle time waiting for the next sector to reach the read write head 21 Table 3 JiffyDOS and Stock interleave values JiffyDOS Interleave Stock Interleave Drive PRG SEQ REL amp USR PRG SEQ REL amp USR 1541 6 10 12 10 1571 4 8 10 6 Depends upon track zone Because JiffyDOS can access and transfer data faster than the stock DOS it uses special interleave values designed to reduce access delays to a minimum For PRG files JiffyDOS uses an interleave that provides the fastest
60. u to easily change the sector interleave on 1541 and 1571 drives This feature makes it possible to increase the disk access speed of particular programs that JiffyDOS seems to have little effect on In some cases changing the sector interleave may be the only way to increase disk access performance especially when a 1571 drive is used with a C 128 in 128 mode For example when a standard interleave is used JiffyDOS does little to speed up Paperclip III 1571 in 128 mode However if the sector interleave 16 is changed to a value of 7 file access speed is doubled See the section titled Setting the Sector Interleave for more information The JiffyDOS File Copier JiffyDOS includes a built in two drive file copier that makes it easy to backup valuable data files to copy files between 1541 1571 and 1581 drives and to copy files to and from RAM expansion units running under Commodore s RAMDOS Although the file copier built into JiffyDOS is not the fastest one in existence it has the following advantages over stand alone copy utilities e The JiffyDOS file copier is built in which enables you to copy files without the hassle of loading a stand alone utility e Copies PRG SEQ REL and most USR files e Saves time and trouble by automatically replacing existing files of the same name on the destination disk The file is first scratched then written Save with Replace is not used e Unlike most utilities the JiffyDOS file
61. ump CTRL W Toggle single file for copy SHIFT RUN STOP Load amp run first program on disk SYS 58451 Re enable the JiffyDOS commands 64 mode SYS 58551 Re enable the JiffyDOS function keys and commands 64 mode SYS 65137 Re enable the JiffyDOS commands 128 mode 50 Compatibility Guarantee JiffyDOS is guaranteed by Creative Micro Designs Inc to be compatible with all commer cial hardware and software designed for use with Commodore C 64 and C 128 computers This guarantee applies for a period of 30 days from the date of purchase If during the term of this guarantee the Buyer determines that a compatibility problem exists a full refund will be issued providing that the Buyer 1 Purchased the unit directly from Creative Micro Designs Inc 2 Returns the unit postage pre paid undamaged with all manuals and any other ma terials included to Creative Micro Designs Inc 3 Submits a written letter of explanation advising the nature of the compatibility prob lem s how they were encountered the name of the incompatible hardware software the manufacturers name and the version number if any Creative Micro Designs Inc shall not be responsible for any incidental or consequential damages of any kind or nature whatsoever including lost economic opportunity or the loss of any data or information which may have resulted from the installation or use of the JiffyDOS system Warranty Creative Micro Designs Inc warrents
62. v secondary address Program same The P Printer output toggle command makes it easy to send BASIC program listings directory listings or output from the JiffyDOS D and T commands to a printer Entering P before issuing a command that normally produces a listing to the screen will result in the screen output being redirected to your printer the default is device 4 secondary address 0 If you wish to specify a different printer device number and or secondary address include the device number and secondary address in the P command as shown in the examples below To restore output to the screen after using the P command simply enter P again Normally the secondary address of 0 is used for uppercase graphics printing and a secondary address of 7 is used for uppercase lowercase printing P Send screen output to printer device 4 secondary address 0 P 5 Send screen output to printer device 5 secondary address 0 P 5 7 Send screen output to printer device 5 secondary address 7 P Restore output to screen assuming P has already been used to redirect screen output to a printer Printing the Screen CTRL P The CTRL P PRINT SCREEN command outputs the current text screen to a printer Pressing CTRL P holding down the CTRL key and then pressing P will cause the text displayed on the screen to be sent to a printer This function automatically detects the current screen mode in order to print from the proper cha
63. ve can provide faster program loading and file access perfor mance in instances where the standard JiffyDOS interleave values are not appropriate Adjusting the interleave can be one of the best ways to improve performance when a 1571 disk drive is used on a C 128 in 128 mode See the section on adjusting the sector interleave under Getting Maximum Performance for step by step procedures on how to apply this command Gapsize Direct Ggapsize Program same The G command changes the sector interleave intersector gap of the current JiffyDOS default disk drive to the value specified by gapsize Valid gapsize values range from 0 to 16 Since no range checking is done by this command be sure that you do not exceed the above limits 0 16 or else unpredictable drive operation may result during writes to disk If you find that you have entered an illegal value simply re enter the command with the 40 correct value To reinstate the default JiffyDOS interleave enter a gapsize of 0 Remember changing the sector interleave is only effective on 1541 1571 and compatible drives do not try to change the interleave of 1581 or MSD drives Also please note that the default device override feature cannot be used with this command G8 Set the sector interleave of the default device to 8 GO Re establish the standard JiffyDOS interleave Combining Files and Creating Backups Direct C newfile oldfile file2 Program C newfil
64. you receive have been programmed to include the latest Commodore upgrades The JiffyDOS ROM for the 1571 eliminates bugs affecting Relative files drive initialization etc and has also been modified to solve the problems with disk backup utilities Fast Hack Em Copy 11 64 128 etc caused by the Commodore upgrade The JiffyDOS Kernal ROM for the C 64 is based on the latest version as are the 64 and 128 mode Kernal ROMs for the C 128 Performance Speeds up all disk operations JiffyDOS has been designed to speed up all operations on 1541 1541 compatible 1571 and 1581 disk drives This includes the initial loading of all types of programs including copy protected software saving reading and writing files from within programs autobooting C 128 in 128 mode scratching validating and formatting 1541 drives JiffyDOS 128 speeds up disk operations in both 64 and 128 modes and is able to speed up the already quick 128 mode operation of 1571 and 1581 drives Works within all types of software Because of its ROM based design JiffyDOS is able to work from within all types of software to increase disk access speed when you need it the most Wordprocessors databases spreadsheets programming languages MIDI software and games all benefit from the built in speed provided by JiffyDOS Since JiffyDOS requires no extra RAM in your computer or disk drive and does not alter vectors it can speed up the operation of all software that relies on
Download Pdf Manuals
Related Search
Related Contents
USER MANUAL - Voltanova BV Network Technologies DVI-x User's Manual Sony VAIO SVF14218CX User Manual - English 電気自動車充電設備導入マニュアル DOLPHIN SUPREME M4 EN FR IT SP DEU User 2007 04 MODE D EMPLOI - WM3800 Descripción: Entretenimiento Asiento Trasero Touareg Issue 16 取扱説明書 Copyright © All rights reserved.
Failed to retrieve file