User manual Dishwasher ZDI12010XA
Contents
1. Dirty filters and clogged spray arms de crease the washing results www zanussi com Do not put in the appliance items made of wood horn aluminium pewter and copper Do not put in the appliance items that can absorb water sponges household cloths Remove remaining food from the items To remove easily remaining burned food soak pots and pans in water before you put them in the appliance Put hollow items cups glasses and pans with the opening down Make sure that cutlery and dishes do not bond together Mix spoons with other cut lery Make sure that glasses do not touch other glasses Put the small items in the cutlery basket Put the light items in the upper basket Make sure that they do not move Make sure that the spray arms can move freely before you start a programme Before starting a programme Make sure that The filters are clean and correctly installed The spray arms are not clogged The position of the items in the baskets is correct The programme is applicable for the type of load and for the degree of soil The correct quantity of detergent is used There is dishwasher salt and rinse aid un less you use combi detergent tablets The cap of the salt container is tight Make a check regularly and if necessary clean them Cleaning the filters Troubleshooting The appliance does not start or it stops during operation Before you contact the Service r2. User manual MANUAL ZDI12010XA ZANUSSI Contents Safety instructions Control panel Programmes Before first use Daily use SI QI SS N A Safety instructions Before the installation and use of the appli ance carefully read the supplied instructions The manufacturer is not responsible if an in correct installation and use causes injuries and damages Always keep the instructions with the appliance for future reference Children and vulnerable people safety Warning Risk of suffocation injury or permanent disability Do not let persons children included with reduced physical sensory reduced mental functions or lack of experience and knowl edge use the appliance They must have su pervision or instruction for the operation of the appliance by a person who is responsi ble for their safety Do not let children play with the appliance Keep all packaging away from children Keep all detergents away from children Keep children and pets away from the appli ance door when it is open Installation Remove all the packaging Do not install or use a damaged appliance Do not install or use the appliance where the temperature is less than 0 C Obey the installation instruction supplied with the appliance Electrical connection Warning Risk of fire and electrical shock The appliance must be earthed Hints and tips _ 9 Care and cleaning ______ 9 Troubleshooting _ __ 10 Technical informa
3. 46 52 8 29 36 51 64 5 1 6 4 36 45 7 23 28 40 50 4 0 5 0 28 35 6 19 22 33 39 3 3 3 9 23 27 5 1 15 18 26 32 2 6 3 2 18 29 4 www zanussi com 5 Water softener Water hardness adjustment German French mmol l Clarke Level degrees degrees degrees dH CrH 11 14 19 25 1 9 2 5 13 17 3 4 10 7 18 0 7 1 8 5 12 2 lt 4 lt 7 lt 0 7 lt 5 12 1 Factory position 2 Do not use salt at this level How to adjust the level of the water softener 1 Make sure that the programme marker on the knob is aligned with the on off indica tor 2 Press and hold the delay button At the same time turn the knob counterclockwise until the programme marker is aligned with the first programme 3 Release the delay button when the start in dicator and the on off indicator start to flash 4 Press the delay button starts to flash The start indicator and the on off indica tor continue to flash The intermittent flashing of gt refers to the current set level e g 5 flashes pause 5 flashes level 5 i i Put 1 litre of water in the salt container only 5 Press the delay button again and again to for the first time change the setting Each time you press the delay button the level number increa ses Filling the rinse aid dispenser 6 To confirm the setting and deactivate the appliance turn the knob until the pro gramme marker is aligned with the on of
4. indicator flashes 1 time intermittently The start indicator flashes continuously The appliance does not drain the water The end indicator flashes 2 times intermittently The start indicator flashes continuously The anti flood device is on The end indicator flashes 3 times intermittently Warning Deactivate the appliance before you do the checks Turn the programme knob until the programme marker is aligned with the on off indicator You cannot activate the appliance Make sure that the mains plug is connected to the mains socket Make sure that there is not a damaged fuse in the fuse box The programme does not start Make sure that the appliance door is closed Press the start button If the delay start is set cancel the setting or wait for the end of the countdown The appliance does not fill with water Make sure that the water tap is open Make sure that the pressure of the water supply is not too low For this information contact your local water authority Make sure that the water tap is not clogged Make sure that the filter in the inlet hose is not clogged Make sure that the inlet hose has no kinks or bends The appliance does not drain the water Make sure that the sink spigot is not clogged Make sure that the drain hose has no kinks or bends The anti flood device is on Close the water tap and contact the Service After the checks are completed turn the pro gramme knob until the programme marker
5. is aligned with programme that was in operation when the problem occurred The programme continues from the point of interruption If the problem occurs again contact the Serv ice If other alarm codes show contact the Serv ice www zanussi com If the washing and drying results are not satisfactory Whitish streaks or bluish layers on glasses and dishes The released quantity of rinse aid is too much Adjust the rinse aid selector to a low er position The quantity of detergent is too much Stains and dry water drops on glasses and dishes The released quantity of rinse aid is not suf ficient Adjust the rinse aid selector to a higher position 11 The quality of the detergent can be the cause Dishes are wet The programme is without a drying phase or with a low temperature drying phase Technical information Dimensions Electrical connection Voltage Frequency Water supply pressure Water supply 1 Capacity Place settings Left on mode Off mode Power consumption Width Height Depth mm Refer to the rating plate Min max bar MPa Cold water or hot water The rinse aid dispenser is empty The quality of the rinse aid can be the cause 1 Refer to HINTS AND TIPS for other pos sible causes 596 818 898 575 220 240 V 50 Hz 0 5 0 05 8 0 8 2 max 60 C 12 0 50 W 0 50 W 1 Connect the water inlet hose to a water tap with a
6. 3 4 thread 2 If the hot water comes from alternative sources of energy e g solar panels aeolian energy use the hot water supply to decrease energy consumption Rating plate Environment concerns Recycle the materials with the symbol Put the packaging in applicable containers to recycle it Help protect the environment and human health and to recycle waste of electrical and electronic appliances Do not dispose 12 appliances marked with the symbol amp with the household waste Return the product to your local recycling facility or contact your municipal office Discard correctly the packaging material Recycle the materials with the symbol 5 www zanussi com www zanussi com 13 14 www zanussi com www zanussi com 15 www zanussi com shop a 8 Y ZN fN 156970840 A 362013
7. efer to the in formation that follows for a solution to the problem 10 To remove filters B and C turn the handle counterclockwise and remove Pull apart filter B and C Wash the filters with water Remove filter A Wash the filter with water Before you put the filter A back make sure that there are no residues of food or soil in or around the edge of the sump Make sure that filter A is correctly positioned under the 2 guides D Assemble filters B and C Put them back in filter A Turn the handle clockwise until it locks An incorrect position of the filters can cause bad washing results and damage to the appliance Cleaning the spray arms Do not remove the spray arms If the holes in the spray arms are clogged re move remaining parts of soil with a thin poin ted object External cleaning Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abra sive products abrasive cleaning pads or sol vents Internal cleaning If you regularly use short duration pro grammes these can leave deposits of grease and limescale inside the appliance To prevent this we recommend to run long duration programmes at least 2 times per month With some problems different indicators flash continuously or intermittently at the same time to show an alarm code www zanussi com The start indicator flashes continuously The appliance does not fill with water The end
8. f button Filling the salt container Caution Water and salt can come out from the salt container when you fill it Risk of corrosion To prevent it after you fill the salt container start a programme 6 www zanussi com Daily use 1 Open the water tap 2 Turn the programme knob until the pro gramme marker is aligned with the pro gramme you want to set Make sure that the appliance is in setting mode refer to Setting and starting a programme Set the correct programme for the type of load and the degree of soil lf the salt indicator is on fill the salt con tainer 3 Load the baskets 4 Add the detergent 5 Start the programme Using the detergent www zanussi com i Fill the rinse aid dispenser when the lens A is clear To adjust the released quantity of rinse aid turn the selector between position 1 lowest quantity and position 4 highest quantity Put the detergent or the tablet in compartment A If the programme has a prewash phase put a small quantity of detergent in compart ment B Using the combi detergent tablets When you use tablets that contain salt and rinse aid do not fill the salt container and the rinse aid dispenser The rinse aid indicator al ways comes on if the rinse aid dispenser is empty 1 Adjust the water softener to the lowest lev el 2 Set the rinse aid dispenser to the lowest position If you stop t
9. he water softener Hard water contains a high quantity of miner als that can cause damage to the appliance and bad washing results The water softener neutralises these minerals The dishwasher salt keeps the water softener clean and in good conditions lt is important to set the right level of the water softener This makes sure that the water softener uses the correct quantity of dishwasher salt and water Using salt rinse aid and detergent Only use salt rinse aid and detergent for dishwasher Other products can cause damage to the appliance The rinse aid helps during the last rinsing phase to dry the dishes without streaks and stains Combi detergent tablets contain detergent rinse aid and other added agents Be sure that these tablets are applicable to the wa ter hardness in your area Refer to the in structions on the packaging of the products Detergent tablets do not fully dissolve with short programmes To prevent detergent residues on the tableware we recommend that you use the tablets with long pro grammes Do not use more than the correct quantity of detergent Refer to the instructions on the detergent packaging Loading the baskets Refer to the supplied leaflet with exam ples of the load of the baskets Only use the appliance to wash items that are dishwasher safe Care and cleaning Warning Before maintenance deactivate the appliance and disconnect the mains plug from the mains socket
10. ltage If the water inlet hose is damaged imme diately disconnect the mains plug from the mains socket Contact the service to re place the water inlet hose Use This appliance is intended to be used in household and similar applications such as Staff kitchen areas in shops offices and other working environments Farm houses By clients in hotels motels and other resi dential type environments Bed and breakfast type environments Warning Risk of injury burns electrical shock or fire Do not change the specification of this ap pliance Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position Do not keep the appliance door open with out supervision to prevent to fall on it www zanussi com Do not sit or stand on the open door Dishwasher detergents are dangerous Obey the safety instructions on the deter gent packaging Do not drink and play with the water in the appliance Do not remove the dishes from the appli ance until the programme is completed There can be detergent on the dishes The appliance can release hot steam if you open the door while a programme operates Do not put flammable products or items that are wet with flammable products in near or on the appliance Do not use water spray and steam to clean the appliance Disposal A Warning Risk of injury or suffocation Disconnect the applia
11. nce from the mains supply Cut off the mains cable and discard it Remove the door catch to prevent children and pets to get closed in the appliance Service Contact the Service to repair the appliance We recommend only the use of original spare parts When you contact the Service ensure that you have the following information that is available on the rating plate Model PNC Serial Number Control panel DI z Em LI 3h OO CANCEL 3 sije On off indicator Delay button Programme marker Start button Indicators 6 Programme knob A Washing phase indicator M Drying phase indicator gt End indicator S Salt indicator This indicator is off while the programme operates Programmes Programme Degree of soil Programme Duration Energy Water 1 Type of load phases min kWh 1 Heavy soil Prewash 130 150 1 3 1 4 13 15 E Crockery cutlery Wash 70 C pots and pans Rinses Dry CP Normal soil Prewash 100 110 1 2 1 6 15 16 NE Crockery and cut Wash 65 C lery Rinses Dry G gt Fresh soil Wash 65 C 30 0 8 9 65 A30 Crockery and cut Rinse 2 lery 4 www zanussi com Programme Degree of soil Programme Dur Energy Water 1 Type of load phases GIS kWh 0 ECO 3 Normal soil Prewash Crockery and cut Wash 50 C lery Rinses Dry iy 4 All Prewash 14 0 1 4 1 The pressure and the temperature of the water the variations of the mains su
12. o use the combi detergent tablets before you start to use separately detergent rinse aid and dishwasher salt do these steps 1 Set the water softener to the highest level 2 Make sure that the salt container and the rinse aid dispenser are full 3 Start the shortest programme with a rins ing phase without detergent and without dishes 4 Adjust the water softener to the water hardness in your area 5 Adjust the released quantity of rinse aid Setting and starting a programme Setting mode i The appliance must be in setting mode to start a programme Turn the programme knob until the programme marker is aligned with a programme on the control panel If the on off indicator comes on and the start indicator starts to flash the appli ance is in setting mode lf the control panel does not show this condi tion press and hold the start button until the appliance is in setting mode Starting a programme without delay start 1 Open the water tap 2 Close the appliance door 3 Turn the knob until the programme marker is aligned with the symbol of the pro gramme you want to set On off indicator comes on Start indicator starts to flash 4 Press Start to start the programme On off indicator and start indicator are on Starting a programme with delay start 1 Set the programme 2 Press the delay button to delay the start of the programme of 3 hours The delay indicator comes on 3 Press the
13. pply the options and the quantity of dishes can change the values 2 With this programme you can wash a load with fresh soil It gives good washing results in a short time 3 With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil This is the standard programme for test institutes 4 Use this programme to quickly rinse the dishes This prevents the remaining food to bond on the dishes and bad odours to come out from the appliance Do not use detergent with this programme Information for test institutes For all the necessary information for test performance send an email to info test dishwasher production com Write down the product number PNC that is on the rating plate Before first use 1 Make sure that the set level of the water 4 Open the water tap softener agrees with the water hardness in 5 Processing residues can stay in the appli your area If not adjust the water softener ance Start a programme to remove them Contact your local water authority to know Do not use detergent and do not load the the water hardness in your area baskets 2 Fill the salt container 3 Fill the rinse aid dispenser Adjusting the water softener Water softener Water hardness adjustment German French mmol l Clarke Level degrees degrees degrees eLa Gi 47 50 84 90 8 4 9 0 58 63 10 43 46 76 83 7 6 8 3 53 57 9 37 42 65 75 6155575
14. start button to start the count down The start indicator comes on Opening the door while the appliance operates If you open the door the appliance stops When you close the door the appliance con tinues from the point of interruption Cancelling the delay start while the countdown operates 1 Press and hold the start button until the start indicator starts to flash 2 Press the start button to start the pro gramme Make sure that there is detergent in the detergent dispenser before you start a new programme Cancelling the programme 1 Press and hold the start button until the start indicator starts to flash Make sure that there is detergent in the detergent dispenser before you start a new programme At the end of the programme When the programme is completed gt comes on lf you do not deactivate the appli ance within 5 minutes all indicators goes off This helps to decrease energy consumption 1 To deactivate the appliance turn the knob until the programme marker is aligned with the on off indicator 2 Close the water tap Important Let the dishes become cold before you re move them from the appliance Hot dishes can be easily damaged First remove the items from the lower bas ket then from the upper basket There can be water on the sides and on the door of the appliance Stainless steel be comes cool more quickly than the dishes www zanussi com Hints and tips T
15. tion ___________ 12 Environment concerns 12 Subject to change without notice Make sure that the electrical information on the rating plate agrees with the power sup ply If not contact an electrician Always use a correctly installed shockproof socket Do not use multi plug adapters and exten sion cables Make sure not to cause damage to the mains plug and to the mains cable Should the appliance power supply cable need to be replaced this must be carried out by our Service Centre Connect the mains plug to the mains socket only at the end of the installation Make sure that there is access to the mains plug after the installation Do not pull the mains cable to disconnect the appliance Always pull the mains plug Do not touch the mains cable or the mains plug with wet hands Only for UK and Ireland The appliance has a 13 amp mains plug If it is necessary to change the fuse in the mains plug use a 13 amp ASTA BS 1362 fuse This appliance complies with the E E C Di rectives Water connection Make sure not to cause damage to the wa ter hoses Before you connect the appliance to new pipes or pipes not used for a long time let the water flow until it is clean The first time you use the appliance make sure that there is no leakage www zanussi com The water inlet hose has a safety valve and a sheath with an inner mains cable A U A Warning Dangerous vo
Download Pdf Manuals
Related Search