Ê800-07600V3ÀÀÀ%Š
Contents
1. Telco 1 Cut The system is not able to communicate with the central monitoring station over the primary phone line l Telco 2 Cut The system is not able to communicate with the central monitoring station over the secondary phone line Wireless Failure The system is not able to communicate with its wireless devices k 1 SAFE MODE 1 From the System Setup screen touch the CS Setup icon 2 Enter your Authorized Code if required 3 Touch the ECP Address icon 1 Touch the ECP Address icon 2 Select the ECP address for this TouchCenter using the Up Dn arrows 3 The available ECP addresses are 1 2 5 6 for residential controls 1 2 3 30 for commercial controls under Rev 10 supports 3 AUIs See Important Note below 1 30 for commercial controls Rev 10 and higher supports 6 AUIs IMPORTANT If multiple TouchCenters are being used they must be set to addresses 1 2 and X where X equals any address from 3 through 30 Only one AUI type touch screen device may be assigned to an address from 3 through 30 on commercial control panels The TouchCenter should not be assigned as a Master Console If the TouchCenter is assigned as a Master Console partitions must be controlled from the Partition screen or using the Console Emulation Mode Apply accepts the address setting 1 From the System Setup screen touch the CS Setup icon 2 Enter your Authorized Code if r2. amp 4 Touch the Output Disable icon to disable the selection 5 Touch the Output Enable icon to enable the Output selection Apply accepts the setting Back cancels your selection NOTE These are local settings for the graphic keypad If user has the maximum number of keypads on the system and wants to disable the same output for all each keypad needs to be set individually Residential Panels and Screen Security Authority Levels Authority levels define the system functions a particular user can perform Depending on the authority assigned to you there are certain system functions you may be prohibited from performing The table below describes the authority levels available in the TouchCenter and provides the equivalent authority level name found in your alarm system manuals Access Level Chosen in TouchCenter Screen Security Matching Authority Level in TouchCenter Authority Level in Panel System Master Master Partition Master Master Standard User Normal Arm Only N A Z Z 2Z Z 2 S1S S S S Installer Guest Guest Commercial System Notes e If the Aux Relay function is set for alarm silenced by User Code 67 this command may only be entered in the console emulation mode e Do not use the common lobby logic function e If fields 2 22 Display Fire Alarms of other Partitions 2 23 Display Burg amp Panic of other Partitions or
3. Hour Minute AM or PM and Month Day Year format 6 Touch Apply DIETO LO Comm E 1 From the System Setup screen touch the Advanced Setup icon 2 Enter your Authorized Code 3 Touch the Keypad Reset icon select OK 4 Touch the Keypad Test icon 5 Touch the Test icon associated with the LCD Display Test Follow the prompts to complete this test 6 Touch the Test icon associated with the Audio Test Testing is displayed while beeps sound from the speaker 7 Touch the Test icon associated with the LED Test Testing is displayed while the 3 LEDs light sequentially top to bottom red green yellow 5 times If the Touch Screen requires recalibration 1 Select the Touch Screen calibration icon and using a stylus follow the screen directions by pressing a series of crosshairs and boxes Q on the screen until done 2 If the test was successful press OK The screen returns to the Keypad Test screen 3 If the test was unsuccessful choose to Retry Ignore or Exit Night Setup 1 Touch the Advanced Setup icon 2 Enter your Authorized Code if required Make sure DST On is checked to enable this feature Select YES on the Time Setting Confirmation pop up window to save the changes in your security system Select No to have the changes affect the TouchCenter only Note A Yes response is recommended Notes If the keypad requires resetting touch OK and t
4. 1610 CAN ULC S303 CAN ULC S304 ULC S545 ULC ORD C1023 and ANSO SIA CP 01 2010 Note For SIA installations used with VISTA 128BPTSIA Controls see the SIA CP 01 Quick Reference Chart located on MyWebTech Document 800 09699 When the Screen Blackout EN50131 Display feature is enabled eThe keypad returns to the Home screen after 30 seconds and the Armed and Ready LEDs turn OFF eThe To Homepage After time setting changes to 30 seconds and the time is non selectable e The Auto Slideshow After is preset to 1 minute and can not be changed eThe Security Message and Lighting screen does not display system status until an authorized user code is entered e The Setup menu does not display system status until an authorized user code is entered Operating Modes Automatic Entry In the rare event that the TouchCenter cannot successfully communicate in its graphic mode with the control panel the TouchCenter displays Problems detected Start Keypad in Safe Mode and requests a Yes or No response If you answer with Yes the TouchCenter enters into the Safe Mode If you answer with No the TouchCenter tries to communicate with the panel again After 3 consecutive times of receiving no response the TouchCenter enters the Safe Mode automatically Manual Entry Note ONLY enter the Safe Mode from the Normal Mode Entering the Safe Mode from the Demo Mode may result in incorrect dis
5. 2 24 Display Troubles of other Partitions are enabled the zones that created the conditions cannot be viewed You must go to that zone s home partition to view e If field 1 11 Zone Bypass After Disarm is enabled you must use the TouchCenter s Console Emulation Mode and the commands Code 64 unbypass all or Code 6 Zone Number unbypass zone to remove zone bypasses e The First to Alarm Display Lock feature field 1 10 is not supported by the TouchCenter e RF Low Battery messages are not supported by the TouchCenter except in the Show Zones screen where a Battery Icon is displayed for the zone with the low battery General Notes e Exit Error and Auto Arm Alert Please Leave Now messages are not displayed by the TouchCenter e When the system has 6150Vs or 6160Vs and 6271Vs attached the Additional Console setting in the 6150Vs displayed as A on the 6150V must be set to 1 and the Additional Console setting in the 6160Vs must be set to Yes UL CO annunciation has not been investigated by UL and may not be used for UL installations For additional troubleshooting procedures refer to the Control Panel Installation Guide WARRANTY For the latest warranty information go to http Awww security honeywell com hsc resources wa Honeywell 2 Corporate Center Drive Suite 100 P O Box 9040 Melville NY 11747 Copyright 2013 Honeywell International Inc http www
6. and resume keypad operation touch anywhere on the screen e The first image is displayed and a list of stored images appears on the screen e When an image is loading no other Picture Setup functions can be performed play previous next add or set wallpaper Touch the TOP button to move up one level in the directory Touch the OPEN button to view larger images and or open directories select from the list of stored images Touch the CLEAR ALL button to clear all pictures from the current slide show rotation Touch the Picture icon on the Home screen to go into the Slide Show feature AEM ELLIE ered atc ICON TITLE FUNCTION Message Record and retrieve Voice 9 Messages Turn certain devices on and off if Light installed and programmed by your installer Security Accesses Security screen Home Returns you to the Home screen Back Reverts to the last screen viewed Displays Emergency functions as programmed by the installer See Programming the Control Panel note Panic Note This icon is displayed and active on all screens except while in the Clean Screen mode and during an LCD Display test in Diagnostics Control Panel This icon alerts the user to a Control Message Panel Message a F Accesses the Message and Picture Multi Media foatires Setup Allows access to Setup menus Voice Status Allows user t
7. honeywell com security FEDERAL COMMUNICATIONS COMMISSION STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User s Manual Unauthorized changes or modifications could void the user s authority to operate the equipment FCC CLASS B STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use The FCC requires the following statement for your information This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures If using an indoor antenna have a quality outdoor antenna installed e Reorient the receiving antenna until interference is reduced or eliminated Move the
8. radio or television receiver away from the receiver control Move the antenna leads away from any wire runs to the receiver control Plug the receiver control into a different outlet so that it and the radio or television receiver are on different branch circuits Consult the dealer or an experienced radio TV technician for help INDUSTRY CANADA CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada FCC IC STATEMENT This device complies with Part 15 of the FCC Rules and RSS 210 of IC Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Cet appareil est conforme a la partie 15 des r gles de la FCC amp de RSS 210 des Industries Canada Son fonctionnement est soumis aux conditions suivantes 1 Cet appareil ne doit pas causer d interferences nuisibles 2 Cet appareil doit accepter toute interference re ue y compris les interferences causant une reception ind sirable 800 07600V3 4 13 Rev C
9. 280 TouchCenter can annunciate a series of words You must use the vocabulary list in your alarm panel coe BUTTON instructions for actual words that may be annunciated Press to reset keypad 6280 001 VO Mounting the TouchCenter This Keypad is for indoor use only and should be mounted at a comfortable viewing level Avoid mounting in areas of high condensation such as bathrooms or in locations where bright light or sunlight shines directly on the screen The TouchCenter can be mounted with or without the mounting plate Use the center securing screw for European installation The 6280 complies with the European Standard EN50131 and is designed to prevent unauthorized use f Standard Mounting with mounting plate Mounting without mounting plate Mounting European Installations using a center securing 1 Select a mounting location 1 Select a mounting location screw 2 Detach the mounting plate by sliding downward 2 Detach the mounting plate by sliding downward and 1 Detach case front by removing the two bottom screws Gently pull 3 Use the mounting plate to mark the location of the mounting discard up using a screwdriver if necessary and pry apart Lift off cover holes on the mounting surface and check for level 3 Use the template provided in the carton to mark the 2 Mount the TouchCenter in its final location see Standard 4 Locate the mounting plate over the mounting surface such that loc
10. 6280 TouchCenter Keypads UTA Installation Guide 800 07600V3 4 13 Rev C For Online Support visit http www security honeywell com hsc resources MyWebTech General Information 6280 TouchCenter This guide provides information on installing and setting up Honeywell s 6280 TouchCenter Keypads The 6280 Front Panel LEDs Series graphical touch screen keypads are Advanced User Interface AUI devices which combine control of your SD SDHC CARD Slot security system multi media and premises lighting Software Information To check the latest software information press the Setup and System Info icons the latest Software Version is displayed i ARMED RED LED oh System is armed OFF System is not armed Compatibility For a list of alarm systems that the TouchCenter can interface with refer to the Compatibility Table in this document An ener cee a i os ON System is disarmed and ready to arm Wiring zL dor System is armed or disarmed but not IMPORTANT If you power the TouchCenter from your panel s auxiliary power output check your panel s sal ready disarmed faults or troubles are present Installation and Setup Guide and verify that this device and others do not exceed your panel s auxiliary power output Agee YELLOW LED ity if 7 j x 4 FLASHING The system contains new capability if it does a supplementary power supply is needed Pesage forthe lest Word List Honeywell OFF No new messages The 6
11. ation of the mounting screws and the cut out for the Mounting or Mounting without the mounting plate install center the wire cable access openings are aligned while passing the TouchCenter assembly on the mounting location Check securing screw supplied and tighten to mounting surface wires cable through the case back gt for level oe 3 Replace the case front and secure using the two bottom screws Go to Wiring the TouchCenter and complete wiring 4 Install 4 screws supplied in the mounting surface Note The European mounting procedure has not been evaluated by 5 Secure the mounting plate to mounting surface using 4 screws leaving screw heads 1 8 above the mounting surface UL supplied 5 Locate the case back over the mounting surface such 6 Slide TouchCenter onto mounting plate that the opening is aligned with the wire cable access opening on the mounting surface while passing the sue s pa wires cable through the opening in the case back enon SECURING SCREW SCREWS 4 TYP Go to Wiring the TouchCenter and complete wiring 6 Mount TouchCenter by sliding onto the screw heads Al BACK DETACH CASE FRONT BY REMOVING SCREWS 2 AND LIFT UP 6280 015 V0 K WALL MOUNTING PLATE OPTIONAL MOUNTING SCREWS INSTALLED 1 8 ABOVE SURFACE e200 006 V1 6280 016 VO Wiring the TouchCenter Mechanical Specifications Width 8 23 inches 209 04
12. e normally not defaulted for AUI type devices To enable the addresses you are using for TouchCenters use an alpha keypad and follow the procedures for Device Programming in your control panel Programming Guide NOTE When the ECP address is changed and Apply is selected the TouchCenter resets nte The Screen Blackout EN50131 Display compliance feature is a European Standard designed to prevent unauthorized users from viewing the status of the Security System Note DO NOT select the Automation Demo Mode option This option should only be selected if instructed to do so by factory service When this option is selected the keypad does not communicate with the control panel and any user can select Advanced Setup screens The Safe Mode may be automatically entered by the TouchCenter program on a communication failure or may be entered manually on command While in the Safe Mode the Home screen displays the Security Panic and Message Icon A message SAFE MODE is be displayed at the bottom of the screen ote Note The Screen Security screen contains a heading of Advanced Setup Central Station Setup Disp amp Audio Setup Event Logs Lighting Message Security and Time Date 3 Touch the Screen Security icon 4 If authority levels are correct touch Back or Home to exit menu 5 If changes are necessary select the line to be changed and the level of user to have access then select the OK ico
13. e when a test is not being performed you can touch the back icon to return to the previous screen or touch the home icon to return to your home page Residential System Notes e If the Clean Me option is set when the maintenance signal is received a Fire Maintenance message and the Display Faults icon is shown However if you display the faults zone 1 is not shown as a faulted zone e If RF Jam Reports are selected and RF Jam is detected the User Authorization screen displays Trouble ZN100 RF Receiver If you enter the console emulation mode the display shows Check 90 RF Receiver Jam e Do not use the Custom Word reminder feature NIGHT Setup Icon Function The TouchCenter is defaulted to arm the system in STAY INSTANT mode when arming the system using the NIGHT icon You can change the TouchCenter so that it arms the system in a different mode when the NIGHT icon is touched by selecting the arming mode to be activated when the NIGHT icon is touched on the Arming screen Note that some displays on the TouchCenter may not have enough space to display the whole name of a partition When this occurs the display shows as many characters as possible starting at the beginning of the partition name We recommend that the partition name be kept to a maximum of 7 characters to ensure the H which indicates the home partition may be seen this is set at the panel E 3 Touch the Output Setup icon lt
14. equired 3 Touch the Options icon 4 Select Lighting or EN50131 Display to turn the option on or off 5 Select Normal Mode or Safe Mode to turn the option on or off Apply accepts all changes 1 Select Safe Mode and then touch Apply 2 Touch the OK icon 3 To exit touch the safe mode bar and touch Yes to return to Normal Mode The TouchCenter resets and restarts in the Safe Mode 1 From the System Setup screen touch the CS Setup icon 2 Enter your Authorized Code if required When the TouchCenter cannot communicate with the alarm panel the message ECP Error is displayed check the following Verify that the AUI type device is enabled in the control panel and that the ECP address in the TouchCenter matches the address enabled in the control panel Use a different address for each device e f powering the TouchCenter from a power supply make sure you have a common ground installed wiring between Power Supply gnd and panel Aux power neg On residential control panels VISTA 20P or equivalent up to four TouchCenters may be used Addresses 1 and 2 in field 189 are enabled by default If the defaults have been changed enable these addresses in field 189 using an alpha keypad and the Data Field Programming procedures located in the panel Installation and Setup Guide On commercial control panels VISTA 128BP VISTA 128FBP or equivalent These addresses in the control panel ar
15. er the User Code for this user 7 Touch the box next to RF Button Zone enter the 3 digit RF Button Zone for this user 8 Touch Save Follow this procedure for deleting and editing users Note The authorized code for adding deleting and editing users is dependent upon the alarm panel you are connected to Check your alarm panel Installation and Setup Guide to determine who can add users Type in the user name 6 characters max no spaces between characters Notes e Use the Shift key for capital letters e Use the BS Backspace key to make corrections The key is not available for use at this time If assigning this user to a wireless key enter one of the zone numbers of the keyfob the wireless key must be programmed before it can be assigned to a user NOTE To edit a User name or number you must delete the User and re enter 3 e PA 5 AB Maximum Number Minimum Software Alarm System of TouchCenters Revision Level VISTA 15P VISTA 20P 2 3 0 FA148CP FA168CPS VISTA 20P FA168CPS i 5 0 VISTA 211P 4 1 0 VISTA 128BP VISTA 250BP 2 oo VISTA 128BPEN 3 7 0 VISTA 128FBP VISTA 250FBP 3 4 1 FA1670C VISTA 128FBPN 3 5 1 VISTA 128BPT VISTA 250BPT 6 10 1 VISTA 128BPTSIA 7 FA1660CT FA1660C FA1700C 3 3 0 Not UL Listed Note Keypad may only be used in the following UL cUL installations UL 365 UL 609 UL 985 UL 1023 UL
16. ew Settings Yes saves the change No discards the change If the Chime Mode and Voice Mode are both selected the Voice Chime is automatically selected It may take a few seconds for the Chime Mode to take effect When the TouchCenter exits the Operating Modes screen your selection is saved The TouchCenter allows you to select from three languages English French Canadian and Latin American Spanish with the default being English If changes are made when you exit a Settings Changed pop up window is displayed asking Remember New Settings Settings include e Backlight Off After X time e Return To Homepage After X time e Auto Slideshow After X time At the Screen Disabled for 30 Seconds screen the touch screen should be wiped clean of fingerprints using a mild soap solution and a soft cloth When the counter reaches zero the window automatically closes and the touch screen is active IMPORTANT Do not use an abrasive cleaning agent or abrasive cloth when cleaning the TouchCenter or damage to the touch screen may occur NOTE The Emergency screen cannot be accessed while running in the clean screen mode Touch Cancel to exit Notes The Picture feature allows you to set up and view up to 1000 photos as a slide show or as your wallpaper display Photo files can be viewed from the SD SDHC Card Formats supported are bmp or jpg files NOTES e To exit the Picture feature at any time
17. he keypad resets If Cancel is selected keypad does not reset After each type of display you are asked if the display was proper If you touch the Yes icon Passed is displayed in the test status column on the Diagnostics screen If you touch the No icon Failed is displayed in the test status column on the Diagnostics screen At the conclusion of the test a pop up Confirmation Window is displayed with the question Did you hear Beeping At the conclusion of the test a pop up Confirmation Window is displayed with the question Did you see chasing LED pattern 3 Touch the Night Setup icon 4 Select the arming mode to be activated when the NIGHT icon is touched on the Arming screen Apply accepts the setting Back cancels your selection Output Setup 2 1 From the Home screen touch the System Setup and Advanced Setup icon 2 Enter your Authorized Code If the Calibration test was successful a confirmation screen appears stating Congratulations Calibration Successful If the test was unsuccessful an error message appears indicating the Part of the screen that failed and stating Calibration fail do you want to retry Notes The NIGHT icon can be set to arm the system in one of five modes e Away Arms all zones with entry delay e Stay Arms perimeter zones with entry delay Instant Arms perimeter zones without entry delay Maximum Arms all zo
18. ht Setup section HOME SETUP Ready To Arm g Ready To Arm lt lt yr 08 57PM Tue 01 11 2000 DISPLAY amp AUDIO SYSTEM SETUP MULTI MEDIA Ready To Arm Adjust the Brightness Volume 1 Touch the Setup icon located in the lower left corner of the Home screen 2 Move the Brightness Volume slide bar to adjust the brightness volume Operating Modes Language Selection From the Setup screen 1 Touch the Disp amp Audio Setup icon 2 Enter your Authorized Code if required 3 Select Chime Mode or Voice Mode to turn the mode on or off 4 To change the Keypads display language highlight the button next the desired language The touchpad will revert back to the Home screen with the selected language applied From the Setup screen 1 Touch the Disp amp Audio Setup icon 2 Enter your Authorized Code if required 3 Touch the desired selection from the drop down list displaying the time period for each option Yes saves the change No discards the change 1 From the Home screen touch the Setup icon 2 Touch the Disp amp Audio Setup icon 3 Enter your Authorized Code if required 4 Touch the CLEAN SCREEN icon to disable the TouchCenter for 30 seconds so you can wipe the screen clean A pop up window displays Touch Screen becomes inactive so that you may wipe the screen clean Please
19. liary power supply always apply power to the control panel first and then the TouchCenter Failure to observe this sequence results in improper operation of the TouchCenter and may result in an ECP Error indication Note Supplementary external power supply must be Listed to UL 603 for UL installations CAN ULC S318 for cUL installations and capable of providing the required backup power Connect the wires to the TouchCenter terminal block as shown e Connect the TouchCenter in parallel with keypads and other peripheral devices using the keypad data ECP bus e If the TouchCenter is used as the primary system keypad maximum wire run length is 150 feet e f more than one keypad is wired to one run then the maximum lengths must be divided by the number of keypads on the run e g the maximum length is 75 feet if two keypads are wired on a 22 gauge run e DO NOT use several hardwired motion detectors in high traffic locations Initial Setup enabling addresses in the control panel using an alpha keypad power up each TouchCenter one at a time and set its address to one of the addresses you enabled in the control panel Note If the top of the screen is displaying ECP Error the TouchCenter ECP Address is not valid for the panel that it is connected to To change the ECP Address enter the default code of 4140 to advance to the next screen Note 4140 is the TouchCenter default installer code before connecting to a control panel Once con
20. mm Height 5 59 inches 141 99mm TERMINAL STRIP POWER SUPPLY IFUSED Depth 1 13 inches 28 70mm Electrical Specifications 9 6VDC 12VDC 13 8VDC AN Our ooe auoe TERMINAL STRIP Backlight OFF Sound OFF 170mA 140mA 125mA YELLOW POWER SUPPLY AUX AUX DATA DATA Backlight ON Sound OFF 270mA 215mA 190mA ONTOS t e AE Backlight ON Sound ON 325mA 255mA 230mA RED 12VD0 Operating Environment Humidity 93 RH non condensing Temperature GREEN Operating 14 Fto 131 F 10 C to 55 C CONTROL UL tested 32 120 F 0 to 49 C Shipping Storage 40 F to 158 F 40 C to 70 C Wire Gauge Length aS M 22 gauge 150 feet 20 gauge 240 feet ery ae 18 gauge 350 feet 16 gauge 550 feet Note Unshielded 4 conductor cable is recommended for the power data wire BLACK GND Use a UL Listed battery backed supply for UL installations The battery supplies power to these keypads in case of AC power loss The battery backed power supply should have enough power to supply the keypads with the UL required minimum standby power time IMPORTANT Keypads powered from supplies that do not have a backup battery do not function if AC power is lost Make sure to power at least one keypad in each partition from the control s auxiliary power output or UL Listed battery backed up power supply IMPORTANT When the TouchCenter is powered from an auxi
21. n The Screen Security screen is re displayed listing any changes Note The User Levels listed on this screen match the User Levels in commercial panels See the chart below for corresponding User Levels in Residential Panels ode A e ote 1 Touch the Code Authority icon The Code Authority icon displays User L 2 Enter the 4 digit User Code for the user Names and Partition Authority Level for 12 that you want to obtain Authority Level the User Code information about 3 Touch the BACK icon Device Eve ote 1 Touch the Device Events icon The control panel must be programmed to 2 To view a record of events in a history log record various system events in installer touch the up down arrow to scroll programming mode Pane O g atio ote 1 Touch the Panel Config icon A Panel Configuration screen is If you select OK the TouchCenter resets and displayed providing details of your system the panel configuration is downloaded from Delete cear the configuration fom ihe TouchCenter and reloads the panel the panel into the TouchCenter configuration into the TouchCenter Ada Velete EQIt a e ote 1 From the System Setup screen touch the User Setup icon 2 Touch the ADD User icon and enter your Authorized Code 3 Touch the box next to Enter User Name enter user name 4 Touch the OK icon 5 Touch the box next to User Number enter User Number for this user 6 Touch the box next to Enter User Code ent
22. nected to a control panel use the panel s installer code Change the ECP Address on the unit using the Up Down arrows and then touch apply to accept the address and reset the TouchCenter Once communication has been restored then use the standard panel installer code for all installer functions Refer to ECP Setup section Language S lection After initial ECP selection is set the Languages menu is displayed Select from English French Canadian and Latin American Spanish Installer Note The 6280 Touch Screen has been calibrated at the factory Ignore the CALIBRATE button that appears on the Options screen after initial ECP setup If the screen should require recalibration do so via the Keypad Test screen See the Diagnostic Tests section for instructions Time Date Setup If not already set from the panel set the current time and date Refer to Time Date Setup section Programming the Control Panel The TouchCenter is not fully operational unless its address in the control panel has been enabled set as an alpha console AUI type device and assigned to a partition where applicable We recommend that you use either a standard alpha keypad or the TouchCenter in Console Emulation Mode when programming the control panel When in the Console Mode the TouchCenter emulates an alpha keypad and the programming of the panel is performed following the procedures provided in your panel
23. nes without entry delay Not to be used for ANSI SIA CP 01 installations Night Residential Panels Only Arms all perimeter zones plus all zones listed in Zone List 5 Notes The Output Setup function allows you to disable Output selection There are a maximum of 18 outputs that can be enabled or disabled You can set the time and date from the Set Time amp Date screen e When the time is set it is stored in the TouchCenter and sent to the control panel when you touch the Apply icon and answer Yes to the following prompt Additionally when using the TouchCenter with a residential panel the panel downloads its time into the TouchCenter once an hour after the clock is set e If Get Time is touched the TouchCenter downloads the time and date from the control panel and exits the Set Time amp Date screen Note This icon appears with residential panels only e g VISTA 15P VISTA 20P Keypad Test A series of diagnostic tests are provided that allow verification of correct operation of the TouchCenter and its connections to the security system There are a total of four diagnostic tests LCD Display Test Audio Test LED Test and Touch Screen Calibration Performing Diagnostic Tests Select any diagnostic test from the Diagnostics screen by touching its associated Test icon All or any individual test may be run when you access the Diagnostics screen however each test must be performed one at a time At any tim
24. o hear system status Allows user to display personal Picture photos in a slide show format Minimize Minimizes the Home screen icons AE Home when viewing wallpaper displays PON PN Maximize Maximizes the Home screen icons i ig Home when viewing wallpaper displays Panel Default Displays The Security screen displays an Icon s if a panel fault occurs The following lists the Icons that are displayed to the left of the Panic icon ICON MEANING gt AC Loss 9 The system is not receiving AC power Bell Failure The system bell or siren has a problem Note This Icon is displayed when interfacing with residential panels only Expander Failure The system has a failure in an expansion module Low Battery The system battery that powers the system during an AC power loss is low LRR Supervision Failure The Communication Device used to communicate with the central station has a supervision failure Multi Media functionality is supplementary only and has not been evaluated by UL UL t 000 4 Play Image Previous Image Next Image Add Image Minimize Home Maximize Home Max Attempts Exceeded The system has exceeded the maximum attempts to communicate with the Central Station Pager Failure The system cannot communicate with an assigned pager
25. pabilities User Related Note e Users added to the system using the TouchCenter graphic user screen must be deleted from the TouchCenter using the graphic screen as well Deleting users from the panel by any other means alpha keypad console emulation mode or Compass downloader does not automatically delete them from the TouchCenter e If the panel has exit tones enabled and you arm the system in the Away mode the TouchCenter beeps continuously throughout the exit period e Use the console emulation mode for the following functions Programming more than 10 system users Programming the Pager report option for users of residential control panels e g VISTA 15P and VISTA 20P Special Function Key operations macros or single button paging End User Scheduling To check for an Alarm Cancelled message if this feature has been enabled in the system Time Date Setup 1 Touch the Time Date Setup icon enter your Authorized Code if applicable 2 Touch the DST icon to have daylight saving time affect your system clock Notes If DST On Daylight Saving Time is selected the TouchCenter adjusts for Daylight Saving time at the month week and time chosen 3 Set the Start DST and then the End DST settings by touching the Month Weekend and Hour that you want DST to start 4 APPLY saves the settings 5 Set the current time by following the prompts and select the current Month Year
26. play of the Emergency Function keys Operating in the Safe Mode This is a limited mode of operation While in this mode e You can use the Security icon to access the Console Emulation Mode of operation to try to clear your faults disarm the system or enter additional Alpha Keypad commands specified in your panel User and Installation Guides You can perform almost all functions that you can perform from a standard non graphic alpha keypad e You can touch the Panic icon and generate Emergency Messages as defined in the panel s home partition for this TouchCenter e The Armed and Ready LEDs on the front of the TouchCenter indicate the TouchCenter s home partition status e The Chime mode functions in the Safe Mode however there is no Voice Voice Chime or Message capability WARNING The Slide Show feature does not start automatically in Safe Mode User Code Setup Each user must be assigned a name with a corresponding 4 digit user code in order to gain access to various features and functions The TouchCenter can hold the identity for 10 Users in its memory If additional Users are needed define the additional Users using the Console Emulation Mode Users for the system are programmed in a central user setup location that provides the specific questions for authorization levels assigned to different users You may want these users to be the same but there are situations in which you may want a user to have limited ca
27. s Installation amp Setup Guide Notes 1 DO NOT perform panel programming while in the Safe Mode 2 When programming your control panel if you change the zone types for your emergency zones you may disable the emergency buttons in the TouchCenter The emergency buttons in the TouchCenter are active for zone types 06 Silent Panic Button and 07 Panic Button 08 Medical Button and 09 Fire Button Additionally the Medical Button is also compatible with a zone type 15 24 Hour Medical for panels that contain this zone type Note Medical functionality has not been evaluated by UL and may not be used in UL Listed applications The TouchCenter should not be assigned as a Master Console If the TouchCenter is assigned as a Master Console partitions must be controlled from the Partition screen or by using the Console Emulation Mode TouchCenter Initialization When initially powered the screen displays the boot sequence and the Set ECP Address screen is displayed If the system is incorporating only one TouchCenter leave the address set to 1 and touch Apply The boot up process continues until completion If there are to be additional TouchCenter units in the system after NIGHT Setup The TouchCenter is defaulted to arm the system in the STAY INSTANT mode when arming the system using the NIGHT icon Select the arming mode to be activated when the NIGHT icon is touched on the Arming screen refer to Nig
28. use a damp soft cloth DO NOT use any liquids sprays or ammonia based cleaners Press CONTINUE to disable touchscreen Panics cannot be initiated during this process 1 Insert your personal media SD SDHC card 2 Touch the Multi Media icon and then touch the Picture icon 3 Select the type of viewing transition desired by touching the Transition arrow Select Standard Horizontal Vertical or Fade Out 4 Touch the Slide Delay arrow to select the time interval 5 10 15 or 20 seconds that you want to allow for each photo to be viewed 5 To add an image to the slide show select the image from the list and press the Add Image icon the image appears on the screen and a check mark appears next to the selected image name on the list 6 To remove an image from the slide show select the image and press the Deselect Image icon To set a picture as wallpaper 1 Use the slide bar to scroll through the list of pictures and highlight the file you want to be displayed on the keypad screen 2 Touch the Set Wallpaper icon view your selection from the Home screen NOTE When viewing wallpaper displays the Home screen icons can be minimized by touching the Minimize Home icon Touch the Maximize Home icon to maximize Home screen icons Picture Icons A Ready To Arm Ready To Arm If changes are made when you exit a Settings Changed Pop up window is displayed asking Remember N
Download Pdf Manuals
Related Search