CX903 3 IN 1 FLOORING NAILER
Contents
1. WARNING Do not fire the nailer when empty Continually firing the nailer with empty magazine will cause internal damage Only fire the empty nailer once or twice to make sure it is functioning properly OILING THE NAILER The CX903 Nailer needs to be lubricated before every use Place three to six drops of pneumatic tool oil provided in the nailer air inlet every two hours of continuous use See figure 2 Figure 2 Lubricating the nailer LOADING THE NAILER Disconnect the nailer form the air supply slide a strip of nails pointed end down into the magazine Push the button inside the pusher pull the pusher all the way back then allow the pusher to slide forward against the nail Strip OPERATING THE NAILER Before operating the nailer make sure you have read and understood the instructions given in this manual WARNING Lubricate the nailer with a few drops of oil as instructed in the manual before operating it Failure to do so could result in internal damage to the nailer and will void the warranty The CX903 comes with two base plates of different thickness The thinner base plate is used with 3 4 flooring and the thicker base plate is used with 1 2 flooring To operate the nailer Attach the desired base plate to the nailer and place down the nailer on the floor with it is base Connect the air supply hose to the nailer Position a flooring strip and tap it into the place with t2. Repairs made by Busy Bee are warranted for 30 days on parts and labour e Any unforeseen repair charges will be reported to you for acceptance prior to making the repairs e The Busy Bee Parts amp Service Departments are fully equipped to do repairs on all products purchased from us with the exception of some products that require the return to their authorized repair depots A Busy Bee representative will provide you with the necessary information to have this done e For faster service it is advisable to contact the nearest Busy Bee location for parts availability prior to bringing your product in for repairs 12
3. 59414194 903 1 FLOORING NAILER User Manual COPYRIGHT 2014 BY CRAFTEX INDUSTRIES INC ive warren 727 lt gt TABLE OF CONTENTS General Safety Instructions for Pneumatic TOOIS 0X909 SECIE Safety 5 2 Unpackin Inventory SSR E MECHANISM a Operating ING NANGI Removing the 15115 A tase Parts List Warranty gt CRAFTEX CX SERIEs GENERAL SAFETY INSTRUCTIONS FOR PNEUMATIC TOOLS Extreme caution should be used when operating all pneumatic tools Know your tool be familiar with its operation read through the user manual and practice safe usage procedures at all times Keep all guards and safety devices place and in working order Always make sure to remove all the keys and wrenches before operation Always keep your work area clean and well lighted Do not use the pneumatic tools in damp or wet locations or where flammable or noxi
4. ackaged and shipped in a box When unpacking carefully inspect that the nailer has not been damaged during transit INVENTORY A Flooring Nailer 1 Mallet eae 1 Safety Goggles 1 D Bottle for Oil 1 E Base Plate 1 Hex Wrenches 2 Figure 1 Inventory FIRING MECHANISM The CX903 does not fire when connected to the air supply unless it is fired by hitting the whack cap with the mallet Before you load you nailer for the first time check the firing mechanism to ensure the safe use To check the firing mechanism Make sure the nailer is disconnected from the air supply Make sure the magazine is empty Place the nailer on the floor with the fastener discharge part is facing down Connect the air hose to the nailer and it should not fire If the nailer does fire immediately disconnect and do not use it until fixed lf it does not fire place the base of the nailer on a scrap of wood that is clean and free of any knots nails or other foreign objects Hit the whack cap with the mallet using moderate force and the nailer should fire If it does not fire then the firing mechanism is not working properly Do not use it until fixed If it does fire then the firing mechanism is working properly
5. e jammed nail lf the jammed nail can not be removed remove the cap screws securing the magazine Now the jammed nail should be visible Remove the jammed nail with a pair of needle nose pliers Re install the magazine and load a new stick CX903 PARTS DIAGRAM 7 aA Ec gt oo e en i 4 5 BS BS D gt he Len ALL 1 ie CX903 PARTS LIST PCS 3 A 03 03 0241 A 00 00 0081 Screw 4 20 0 Cylinder barrel A 02 00 1311 O Ring 0 0 A 02 00 1321 O Ring 34 4 6 A 02 00 1301 O Ring 16 2 65 gt A 00 04 0071 02 00 1291 O Ring 13 2 1 8 A 06 01 0121 9 0 N3 A 00 05 0271 Washer 10 A 06 00 0791 Driver blade A 04 30 A 03 09 1 A 02 05 0241 GASKET ae bo 2 2 07 06 0441 0 A 02 00 1331 O Ring 50 3 55 A 03 16 1 1 Supporting Seat A 00 00 0271 Screw 6 20 0 Ae Oe OL OSL The front ba
6. h to persons or damage to property or for incidental contingent special or consequential damages arising from the use of our products RETURNS REPAIRS AND REPLACEMENTS To return repair or replace a Craftex product you must visit the appropriate Busy Bee Tools showroom or call 1 800 461 BUSY Craftex is a brand of equipment that is exclusive to Busy Bee Tools For replacement parts directly from Busy Bee Tools for this machine please call 1 800 461 BUSY 2879 and have your credit card and part number handy e All returned merchandise will be subject to a minimum charge of 15 for re stocking and handling with the following qualifications Returns must be pre authorized by us in writing We do not accept collect shipments Items returned for warranty purposes must be insured and shipped pre paid to the nearest warehouse Returns must be accompanied with a copy of your original invoice as proof of purchase Returns must be in an un used condition and shipped in their original packaging a letter explaining your reason for the return Incurred shipping and handling charges are not refundable e Busy Bee will repair or replace the item at our discretion and subject to our inspection e Repaired or replaced items will be returned to you pre paid by our choice of carriers e Busy Bee reserves the right to refuse reimbursement or repairs or replacement if a third party without our prior authorization has carried out repairs to the item e
7. he metal side of the mallet Do not position the flooring strip with the nailer Always use the metal side of the mallet WARNING Always test the nailer on a sample flooring strip before installing pre finished flooring to make sure the nailer does damage the finish Replace the base plate if it is damaged or it is damaging the floor 7 Position the nailer with the guide plate on the flooring so that the cleat on the botton of the nailer is lined up with the edge of the groove in the flooring Use the mallet with its rubber end and hit the whack cap with moderate force to shoot a nail into the wood Make sure not strike multiple times to shoot one nail into the wood This will cause a jam or possible injury Now remove the nailer and check the for proper depth If the nail is shot too deep into the wood Slightly decrease the air pressure If the depth is too shallow slightly increase the air pressure IMPORTANT The depth of the nail into the wood is not always consistent due to variations in the flooring material Some times you may want to tao a few nails flush with a hammer and a nail punch REMOVING JAMMED NAILS sometimes the nail gets jammed Jammed nail must be removed before using the nailer again To clear the jammed nail Disconnect the air supply to the nailer Pull the magazine loader all the way back and remove the nail stick Now use needle nose pliers to remove th
8. nailer if you are not sure about its indented operation Make sure you have read understood all the safety instructions in the manual and you are familiar with your shaper before operating it If you fail to do so serious injury could occur WARNING The safety instructions given above can not be complete because the environment in every shop is different Always consider safety first as it applies to your individual working conditions CRAFTEX CX SERIES CX903 3 IN 1 FLOORING NAILER FEATURES MODEL CX903 3 1 FLOORING NAILER As part of the new line of Craftex CX Series pneumatic tools we are proud to offer the CX903 a 3 in 1 Flooring Nailer By following the instructions and procedures laid out in this user manual you will receive years of excellent service and satisfaction The 903 is professional tool and like all pneumatic tools proper care and safety procedures should be adhered to TOOL AIR FITTING This tool uses a 1 4 NPT male plug OPERATING PRESSURE 70 115 PSI 120 PSI AIR CONSUMPTION 7 78 SCFM 102 PSI NOISE CHARACTERISTIC VALUES The level of noise does not exceed 95 dB A with average of 82 dB A NAILER DIMENSIONS 52 2 cm x 10 cm x 42 8 cm FASTENER SIZE Crown Width 1 2 13mm x Wire Size 15 1 2 to 16 Gauge Max Length 2 50mm TOOL WEIGHT Weight 10 8 lbs 4 9 kgs 5 UNPACKING The tool is properly p
9. ous fumes may exist Always keep bystanders away or at a safe distance from your work area Disconnect the power source when changing drill bits hollow chisels router bits shaper heads blades Knives or making other adjustments or repairs Never leave a tool unattended while it is in operation Do not force the tool It will do a better and safer job at the rate for which it is designed Always use the right tool Do not attach any part to the tool for which it is not designed Always check the hose for any damage before using the pneumatic tool Disconnect the tool before servicing changing accessories or moving to another location Always check the tool for damaged or broken parts loosen screws or bolts or any other unsafe condition that may affect the tool operation Repair the damaged parts before operation Do not overreach Always keep proper footing and balance Always use safety glasses and a dust mask while operation Always keep your tool lubricated and clean for best and safest performance Be alert Do not use prescription or other drugs that may affect your ability or judgment to safely use your tool lt gt CRAFTE ar 3 CX903 3 IN 1 FLOORING NAILER SPECIFIC SAFETY INSTRUCTIONS Read and follow all the instructions and safety precautions in the user manual before operation For the protection of your eyes always wear safety glasses goggles or face shield while ope
10. rating this tool Do not connect the nailer to compressed air that exceeds 120 PSI Never point the nailer at others Always carry the nailer by handle Make sure the air hose is good condition and long enough to read your work area without stretching Make sure no body is standing close enough to be hit when swinging the mallet Make sure not to drive one nail on the top of the other The nail may deflect and cause injury Do not drive fasteners close to the edge of the work piece as the wood may split allowing the fastener to be deflected possibly causing injury Always disconnect the air hose before installing nails clearing a jam moving to another work area performing maintenance or when the tool is not in use Do not use a check valve or any other fitting that allows air to remain in the tool If used the tool can remain charged with air after disconnecting and this will be able to drive a fastener even after the air hose is disconnected possibly causing injury Do not connect the nailer to pressurized oxygen or other combustible gases as a power source Only use regulated compressed air Do not use gasoline or any other flammable liquids to clean the nailer vapors in the nailer will ignite by a spark and cause it to explode Always use the fasteners for which the tool is designed lf the nailer is leaking air damaged or not working properly do not use it before repairing Do not use the
11. se 1 08 00 0451 bo 3 00 00 1 Screw 6 A 08 01 1221 ww 10 39 A 07 07 0631 40 A 07 06 0451 00 00 0161 00 06 0531 A 01 00 0651 A 00 07 0041 A 07 00 0591 A 00 07 0011 Front Locating sleeve A 00 05 0321 A 00 04 0011 A 00 00 1 Screw 4 12 03 03 0241 Cylinder assembly B 06 00 0701 07 01 0761 CRAFTEX 11 CX SERIES X CRAFTEX XY cX WARRANTY CRAFTEX 3 YEARS LIMITED WARRANTY Craftex warrants every product to be free from defects in materials and agrees to correct such defects where applicable This warranty covers three years for parts and 90 days for labour unless specified otherwise to the original purchaser from the date of purchase but does not apply to malfunctions arising directly or indirectly from misuse abuse improper installation or assembly negligence accidents repairs or alterations or lack of maintenance Proof of purchase is necessary All warranty claims are subject to inspection of such products or part thereof and Craftex reserves the right to inspect any returned item before a refund or replacement may be issued This warranty shall not apply to consumable products such as blades bits belts cutters chisels punches etceteras Craftex shall in no event be liable for injuries accidental or otherwise deat
Download Pdf Manuals
Related Search