Quick Start M1 Install Manual
Contents
1. The Encore M1 is a state of the art Two way motorcycle alarm that utilizes advanced detection techniques to fully secure and protect your Motorcycle It offers both Radar and impact sensing and incorporates advanced Starter or Ignition shutoff Please read and understand this manual before you begin your installation Powered By P a E 2I DI ee Wire Diagram Antenna RED System Power Blue Horn Output Violet Kill OUTPUT White Rt Parking Light White Lt Parking Light Yellow 12 Volt ACC Violet Kill INPUT Blue Wht Horn Input Learn Button M1 Two Way Motorcycle Alarm Black System Ground Locking Tab Blue Wht 2 Pin Connector Siren Yellow Connector Front View Main wire Harness 9 Pin Main Harness Red Main unit Power 12 Volt Please connect this wire to constant 12 volt Power at the battery or any stable power source Black Ground Connect this wire to any stable ground or the negative battery terminal of the motorcycle Yellow This wire should be connected to 12 Volt Ignition This wire should have power when the Ignition Key is in the ON or RUN position only Violet 2 These wires are the starter or ignition cutoff They are a relay input and output The starter wire or Ignition wire of the motorcycle should be confirmed and then cut Both sides of the cut wire should go to either violet2. 3 axis sensor is located in the main unit and will sense impact armed The remote will show a lock symbol when the system is armed better if secured with screws Please plan and choose this location carefully Disarming the System By pressing button 2 or disarm on the remote you Operation will disarm the system The lights will flash 2 times mr 5 Button Layout and the siren and horn will chirp twice The remote will show an unlock symbol If the motorcycle is Button 1 Arm disarmed and the ignition is not turned ON within 30 8 3 H Fu Button 2 Disarm seconds the unit will rearm itself To stop this Button 3 Locate process turn the ignition switch to ON or press the disarm button twice Button 4 Microwave ON OFF within 1 second If the ignition switch is not turned ON the unit will interpret this as an accidental disarm and will rearm the system Not Armed Reminder If the ignition switch is turned off and the unit has not been armed within 20 seconds the unit will alert the user by chirping 3 times and flashing the lights 3 times It will also alert the remote and the unlock icon will flash 3 times The unit will not automatically arm Silent Mode If the Arm button or button 1 is pressed twice within 2 seconds the unit will be in silent mode and the speaker icon on the remote will have a line through it In this mode the alarm will function as normal but will NOT honk the horn or activate the siren when a trigger is recogniz
3. Connections Siren wires The siren plugs into the two pin connector dedicated for the siren output Please secure the siren in a good place facing down and attach with two screws This siren has double sided tape on the back but screws should be used to secure it in place Antenna The antenna should be mounted away from surrounding metal in an area that is open to allow for the greatest range It can be placed beneath fairings or in any area including the handle bars tail side covers or under the seat LED Indicator The LED should be mounted in an area where it can be seen by the rider as well as any unwanted intruder This will act as a visual deterrent and will give the rider notification of the status of the system Microwave or Radar Sensor The Radar sensor is designed to detect movement above and around the motorcycle It connects to the three pin plug on the main unit This sensor will penetrate all surfaces except metal It should be mounted in the middle of the motorcycle facing UP and can be installed under the seat or in any open area The unit will trigger warn away Display as well as full trigger depending on the amount of time the disturbance Mode Menu takes place If the radar sensor sees movement within its range for 3 SET TIME ALARM AUTO ARM_ EXT seconds it will trigger the warn away of the alarm with a few siren and horn Alarm CN beeps If the disturbance continues it will trigger the primary trigger and wi
4. Programming remote transmitters To program replacement remotes please follow the procedures below The unit will hold a maximum of 2 remote codes and when programming all other older remote codes will be deleted Method 1 Turn On and Off the ignition 8 times and leave it ON and wait 2 seconds The LED will glow solid Press button 1 of the new remote control to set the code The LED will flash twice and the siren will chirp twice Press button 1 on the second remote and the LED will flash 4 times and the siren will chirp 4 times Turn Off the ignition to set the codes Method 2 With the ignition ON press firmly and hold in the programming button on the back of the main unit The LED will glow solid Press button 1 of the new remote control to set the code The LED will flash twice and the siren will chirp twice Press button 1 on the second remote and the LED will flash 4 times and the siren will chirp 4 times Turn Off the ignition to set the codes Battery Replacement The M1 remotes use a AAA Battery and will last approximately 4 months depending on use For Customer service please email customerservice encoreautomotivesystems com For Dealer Tech Support please call 855 463 6267 Ext 3 Encore Automotive Systems 27240 Turnberry Lane Suite 200 Valencia CA 91355 www encorea utomotivesystems com Gs a 4S f M1 Two Way Motorcycle amp ATV Alarm Professional installation only Installation and User s Manual
5. ed When the system is triggered by either warn away or full trigger the lights will flash on the motorcycle but no audible alarm will be heard The Remote will make a sound and vibrate while showing what was triggered If the warn away was triggered the unit will beep and vibrate showing the user what triggered the system If full trigger is initiated the unit will add a melody sound as well All other functions of the unit will stay the same To return to audible mode press the arm button again twice This will toggle in and out of silent mode and can be verified by the speaker icon on the remote lt Audible Mode aa Silent Mode Trigger Disarm If the unit is triggered press the Disarm button to disarm the system or press the arm button to stop the siren and keep the system armed Arming and deleting the Microwave sensor There are times when your motorcycle will be in an area of constant activity This may trigger your radar or microwave sensor When parked in areas close to activity the Microwave or Radar sensor can be shut off to eliminate false triggers This can be done by pressing button 1 to arm the system and within 2 second pressing button 4 The remote will make a melody sound and the siren will chirp once indicating the radar sensor will be off The sensor will turn ON again the next time the system is armed Locate By pressing button 3 the motorcycle will chirp the horn and siren 3 times and will flash the lights 3 t
6. ger a full Zol a event The siren and horn will sound and the parking lights will flash for 30 seconds 8 3 B Fn Setting the time on the remotes The remotes have both the time and an alarm timer function These can be set to show the time of day as well as an alarm time They are in 24 hour military time as there are no AM or PM capabilities in the remote Setting the Time e Press button 1 and 2 at the same time for 2 seconds The remote will make a tone and the lock icon will flash Then press the Arm button to select between time minutes time hours alarm ON or Off alarm minutes alarm hours and exit The selected characters will flash rapidly e Press button 2 to adjust the flashing characters and press button 1 to move to the next segment e Once the time and alarm is set Move the display until the top of the display says set or exit and there is nothing else in the clock position e Press both button 1 and 2 together again for 2 seconds until the unit reacts with a sound Your values have been set e If you wish to exit without saving the settings press the disarm button to exit
7. heard Press again for level 3 4 and 5 in the same manner Once the desired setting is achieved press and hold the disarm button or button 2 until a long chirp is heard This will indicate that the setting has been set into the unit s memory Triggers There are three trigger points for the system with the impact and Radar having warn away trigger as well Warn away will give notice that your motorcycle is armed when a small disturbance is sensed Radar Sensor Trigger with warn away When movement is sensed for three seconds the radar sensor will trigger the warn away and fN X the unit will chirp three times If the mas ani disturbance continues the unit will go into F3 T full trigger mode The remote will vibrate and E3 Y make a melody noise The LCD indicator will alert you that the trigger was from the radar sensor This is shown by the rotating box in the clock area Impact Sensor Trigger with warn away When a slight impact is felt by the sensor for 2 seconds the unit will trigger the warn away and the unit will chirp three times If the fN g3 i i Silla Es AP disturbance continues the unit will go into full trigger mode The remote will vibrate and 8 00 M make a melody noise The LCD indicator will 8 8 8 alert you that the trigger was from the Impact sensor This is shown by the remote pictured here Ignition Trigger When the system is armed and the ignition 1 a switch is turned ON the unit will trig
8. imes to help you locate the motorcycle in large parking lots Starter or Ignition Kill If installed the unit will disable the starter or ignition when the unit has been triggered Warn away and full triggers will disable this circuit If a starter kill was wired on the motorcycle during trigger the motorcycle will not start If an Ignition disable was connected the motorcycle will not run during trigger events Emergency Disarm In the event that the system is armed and the remote control has been lost or is not functioning the unit can be manually disarmed by turning the ignition switch ON and OFF 10 times quickly and the key left in the ON position for 3 additional seconds The system will not arm again until a disarm signal is receive by the unit from any transmitter Out of Range Check Yul Though the M1 Motorcycle alarm system has range of up to one mile this can vary with different environmental conditions If the unit is out of range for paging the remote will play a melody sound and the signal strength bar will be at no bars LED Indicator In the armed status the LED will blink twice every 2 seconds The LED will flash continuously during any trigger event and if triggered will flash 4 times every 2 seconds until the ignition is turned ON This indicates the alarm was triggered while armed Impact and Microwave sensor adjustment The Microwave sensor and the impact sensor both can be adjusted to obtain the best sensitivi
9. ll sound the alarm This sensor can be overridden by the remote in Sound or SilentMode gt gt Trigger Display situations where there are many motorcycles parked together The Battery Indicator sensitivity of the sensor can be adjusted by turning the adjustment screw on the sensor Turn the adjustment screw Clockwise for more sensitivity and 5 ra I Signal Strength counterclockwise less The sensor will only trigger if motion is sustained for Oh 1 8 Yul 8 gt more than 3 second The circuit is design in this manner to minimize false Time alarms and should not be used if there is always normal activity around Functions where the motorcycle is parked Arming the System Main Unit The main unit is water resistant and should be mounted in a With the ignition in the OFF position Press button location that offers the best protection form the elements and is hard to get number 1 or Lock to Arm the system The siren wW to by a would be intruder This can be mounted in the fairing side cover and horn will chirp once if connected and the lights ol t under the tank or the tail of the motorcycle or ATV It should be securely on the motorcycle will flash one time The system mounted with screws if at all possible The main unit does come with high is now armed While armed the LED will flash two gG Q Tt strength Velcro included but securing this unit will provide better results times every 2 seconds indicating the system is The impact
10. ty for the motorcycle Caution should be used in the setting of these devises The more sensitivity each sensor has the more likely it will false trigger Microwave or Radar sensor This sensor is designed to help eliminate false alarms by filtering the triggers from the sensor The radar sensor must see movement for 3 second before it will trigger the system Ifa leaf falls from an overhanging tree it will be ignored The sensor can be adjusted at the sensor with a small screwdriver The adjustment is fairly straight forward Turn the adjustment counter clockwise for less sensitivity and clockwise for greater sensitivity The adjustment will only turn 100 degree in either direction Do not force the adjustment past its physical stops The LED just above the adjustment port will light every time the unit sees motion of any kind This will only light if the system is armed and the radar sensor has not been deleted Impact Sensor The impact sensor is located in the main unit and adjustments can be made directly from the remote control In the disarmed mode press and hold the disarm button or button two for approximately 4 seconds The unit will chirp Press the Arm button 1 to change the sensitivity There are 5 levels of sensitivity and the factory setting is 3 Level 1 is the highest sensitivity and level 5 is the lowest Press the Arm button and the unit will respond with one chirp Press again and it will be set to level 2 Two chirps will be
11. wires One is the input and the other the output Either wire can be used but both need to be connected to complete the circuit This circuit is normally closed and will disconnect when the system has been triggered Please use caution if interrupting the ignition of the vehicle White Wires 2 The two white wires are the output for the turn indicators One is to be connected to the right positive side of the turn indicator and the other is for the left Both have positive outputs from a relay and both are isolated so they will not affect turn indicator operation Blue White This is the input for the horn of the motorcycle It will allow you to change the polarity of the horn output If the motorcycles horn is triggered by a negative or ground signal connect this wire to ground If the horn has a positive trigger this wire should be connected to a positive power source or the red wire of this harness Please check the horn when the key is ON and determine if the trigger of the horn is positive or negative Once determined turn the key to the OFF position and insure the trigger is correct This wire is attached to the common post of a horn relay and will be open when the horn is not used Blue This is the horn output and will deliver the output polarity based on the connection to the Blue white wire above Please install the siren as most horn wires are accessible from the outside of the motorcycle and can easily be disconnected Other
Download Pdf Manuals
Related Search