Home

Gebrauchsanweisung User Manual Manuel d - spot

image

Contents

1. Smallest unit displayed laser point at distances 50 m 164 ft 40 m 132 ft 35 m 115 ft 1mm 1 16 in 6 30 mm 10 50 m General Laser class 2 Laser type 635 nm lt 1 mW Protection class IP40 not water protected Autom laser switch off after 90 s Autom power switch off after 180 s Battery durability 2 x AAA up to 3000 measure ments 116 x 45 x 29 mm 4 57 x 1 77 x 1 14 in Weight with batteries 0 10 kg 3 527 oz Temperature range Storage Dimension H x D x W 25 to 70 C 13 to 158 F 0 to 40 C 32 to 104 F Operation eee DUT Pre Ss N S in accordance with ISO 16331 1 Ww A applies for 100 target reflectivity white painted wall low background illumination 25 C applies for 10 to 500 target reflectivity high back ground illumination 0 C to 40 C Tolerances apply from 0 05 m to 10 m with a confi dence level of 95 The maximum tolerance may deteriorate to 0 15 mm m between 10 m to 30 m and to 0 2 mm m for distances above 30 m applies for 100 target reflectivity background illumination of approximately 30 000 lux geo FENNEL EcoDist Pro Functions Distance measuring Permanent measuring Pythagoras 2 point 3 point i yes i yes yes yes Message Codes If the message Error does not disappear after switching on the device repeatedly contact the dealer If the message InFo appears with
2. a number press the Clear button and observe the following instructions No Cause Correction 204 Calculation error Perform measurement again 252 Temperature too Let device cool down high 253 Temperature too Warm device up low 255 Received signaltoo Change target surface weak measuring e g white paper time too long 256 Received signaltoo Change target surface high e g white paper 257 Too much back Shadow target area ground light 258 Measurement Correct range outside of meas uring range 260 Laser beam inter Repeat measurement rupted Care e Clean the device with a damp soft cloth e Never immerse the device in water e Never use aggressive cleaning agents or solvents geo FENNEL EcoDist Pro Safety Instructions The person responsible for the instrument must ensure that all users understand these directions and adhere to them Areas of responsibility Responsibilities of the manufacturer of the original equipment geo FENNEL GmbH D 34225 Baunatal short geo FENNEL The company above is responsible for supplying the product including the User Manual in a completely safe condition The company above is not responsible for third party accessories Responsibilities of the person in charge of the instrument e To understand the safety instructions on the product and the instructions in the User Manual e To be familiar with local safety regula tions relating to accident preventio
3. wavelength 620 690nm Beam divergence 0 16 x 0 6 mrad Impulse duration 0 2 x 10s 0 8x 109s Eco A O Batteries d Hungary TA nea 1 Complies wi SN 1040 11 e xcept far e No 50 Sa Se 2 24 20 CS Subject to change drawings descriptions and technical data without prior notice
4. GC FENNEL ECOLINE EcoDist 77 DE Gebrauchsanweisung EN User Manual FR Manuel d utilisation IT Manuale d uso ES Manual de usuario RU PyKkOBOZCTBO NONnb3s0BaTenaA PL Instrukcja obs ugi DA Brugervejledning NL Gebruiksaanwijzing NO Brukerveiledning sv Handbok Table of Contents Instrument Set up 2 EES 10 eewer Eeer 2 Electromagnetic Compatibility EMC 10 E EE 2 FCC statement applicable in U S 11 Depay esnea ee Gg 3 Laser classification 11 Insert batteries 3 Sa aa aaa cea laa 11 Operations 4 Switching ON OFF 4 Clear 4 Message Codes 4 Adjusting measuring reference 4 Distance unit setting 4 Measuring Functions 5 Measuring single distance 5 Permament measuring 5 Add Subtract 5 Area 6 Volume 6 Pythagoras 2 point 7 Pythagoras 3 point 7 Technical Data 8 Message Codes 9 Gare 9 Safety Instructions 9 Area
5. Refer to section Technical data The device is designed for use in areas permanently habitable by humans Do not use the product in explo sion hazardous areas or in aggressive environments geo FENNEL EcoDist Pro Disposal Z CAUTION Flat batteries must not be disposed of with household waste Care for the environ ment and take them to the collection points provided in accordance with national or local regulations The product must not be disposed with household waste Dispose of the product appropri ately in accordance with the X national regulations in force in your country Adhere to the national and country specific regulations Product specific treatment and waste management can be downloaded from our homepage Electromagnetic Compatibility EMC Z WARNING The device conforms to the most stringent requirements of the relevant standards and regulations Yet the possibility of causing interference in other devices cannot be totally excluded Safety Instructions FCC statement applicable in U S This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential instal lation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may
6. cause harmful inter ference to radio communications However there is no guarantee that inter ference will not occur in a particular instal lation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interfer ence by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Laser classification The device produces visible laser beams which are emitted from the instrument It is a Class 2 laser product in accordance with e IEC60825 1 2007 Radiation safety of laser products Laser Class 2 products Do not stare into the laser beam or direct it towards other people unnecessarily Eye protection is normally afforded by aversion responses including the blink reflex Z WARNING Looking directly into the beam with optical aids e g binoculars telescopes can be hazardous Z CAUTION Looking into the laser beam may be hazardous to the eyes geo FENNEL EcoDist Pro Labelling Laser Radiation Do not stare into the beam Laser class 2 acc IEC 60825 1 2007 Maximum radiant power lt 1mW Emitted
7. ery Area symbol is flash Volume ing Measuring 4 ZN7 sb 7 reference Nal le LA OO 0002 no TARO 0 0 0 0 tim lt gt R gt ja Re Anne OOOO Measuring l LI LIL Addition Units Subtraction Main line geo FENNEL EcoDist Pro Operations Switching ON OFF A A OFF 2 sec Device is turned OFF Adjusting measuring reference cb TTT eee cf Distance is measured from the front of the device Distance unit setting Switch between the lows following units 2 sec prm Undo last action Message Codes A A 1x If the info icon appears with a OFF number observe the instruc tions in section Message Codes Example Distance is measured from the rear of the device standard setting geo FENNEL EcoDist Pro Measuring Functions Measuring single distance Target surfaces Measuring errors can occur when meas 1 uring to colourless liquids glass styrofoam or semi per meable surfaces or when aiming at high gloss surfac es Against dark surfaces the measuring time increases N e Aim active laser at target The last value mea A wi sured is displayed Ro Stops permanent measur es ing Aim active laser at target The result is shown in the main line and the measured value above This process can be repeated as required The same process can be The next meas The next meas used for adding or subtract
8. ing urement is added urement is sub D tic areas or volumes to the previous tracted from the our one previous one geo FENNEL EcoDist Pro 3 Measuring Functions Area Aim laser at first target point Volume Aim laser at first target point The result is shown in the main line and the measured value above The result is shown in the main line and the measured value above Aim laser at sec ond target point Aim laser at sec Aim laser at third ond target point target point geo FENNEL EcoDist Pro Measuring Functions Pythagoras 2 point ck e a i Ip Aim laser at up Aim laser rectan per point gular at lower The result is shown in the main line and the measured dis tance above Pressing the meas uring key for 2 sec in the function acti vates automatically Minimum or Maxi mum measure ment ji o EIE E E E SS I feste fe Aim laser at up Aim laser at rec Aim laser at lower point per point tangular point The result is shown in the main line and the measured distance above Pressing the measuring key for 2 sec in the function activates automatically Minimum or Maxi mum measurement geo FENNEL EcoDist Pro EN Technical Data Distance measurement Typical Measuring Tolerance 2 0 mm 0 08 in 3 0 mm 0 12 in Maximum Measuring Tolerance Range of target plate Typical Range Range at unfavourable condition
9. n e Always prevent access to the product by unauthorised personnel 2 Safety Instructions Permitted use Measuring distances e Tilt measurement Prohibited use Using the product without instruction Using outside the stated limits Deactivation of safety systems and removal of explanatory and hazard labels Opening of the equipment by using tools screwdrivers etc Carrying out modification or conversion of the product Use of accessories from other manufac turers without express approval Deliberate dazzling of third parties also in the dark Inadequate safeguards at the surveying site e g when measuring on roads construction sites etc Deliberate or irresponsible behaviour on scaffolding when using ladders when measuring near machines which are running or near parts of machines or installations which are unprotected Aiming directly in the sun Hazards in use Z WARNING Watch out for erroneous measurements if the instrument is defective or if it has been dropped or has been misused or modified Carry out periodic test measurements Particularly after the instrument has been subject to abnormal use and before during and after important measurements Z CAUTION Never attempt to repair the product your self In case of damage contact a local dealer Z WARNING Changes or modifications not expressly approved could void the user s authority to operate the equipment Limits of use i
10. s of responsibility 9 Permitted use 10 Prohibited use 10 Hazards in use 10 Limits of use 10 geo FENNEL EcoDist Pro J Instrument Set up Introduction The safety instructions and the user manual should be read through carefully before the product is used for the first time l The person responsible for the product must ensure that AN all users understand these directions and adhere to them The symbols used have the following meanings ZAWARNING Indicates a potentially hazardous situation or an unintended use which if not avoided will result in death or serious injury Z CAUTION Indicates a potentially hazardous situation or an unintended use which if not avoided may result in minor injury and or appreci able material financial and environmental damage Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner Overview Display NG EcoDist P O OC On Measure Add Area Subtract mS D Volume Pythagoras Measuring reference vs Clear OFF Unit geo FENNEL EcoDist Pro Instrument Set up Display Insert batteries To ensure a reli able use do not use zinc carbon Battery pi o Pythagoras batteries Fok Change batter ies when batt

Download Pdf Manuals

image

Related Search

Related Contents

Number 2: 2005 April  Samsung M187HNR Инструкция по использованию  Service Manual TAN-TAG  Dataflex Printer Boy 100  Demonstrator Exercises  NetComm IN5699 Network Router User Manual  Warning - Casualplay  Sanyo VPC-CS1EX User's Manual    AXON AX 50 USB (Italiano)  

Copyright © All rights reserved.
Failed to retrieve file