Home

Manual

1. 2 11 Chapter 3 Award BIOS Setup 3 1 System Test and Initialization 3 2 3 2 Award BIOS Setup 3 3 Chapter 4 Driver Installation 4 1 Installation in aene ere etae 4 3 Appendix A Programming The Watchdog Timer A 1 Programming seen A 2 A 2 118712 Watchdog Timer Initial Program A 6 Appendix B I O Information B 1 I O Address Map seem B 2 B 2 Memory Address Map B 3 vii Embedded Controller AEC 6910 B 3 IRQ Mapping Chart sees B 4 B 4 DMA Channel Assignments B 4 viii Embedded Controller AEC 6910 Chapter General Information Chapter 1 General Information 1 1 Embedded Controller AEC 6910 1 1 Introduction The AEC 6910 BOXER S Advanced Embedded Control system continues the BOXER design concept but focuses on the fast expanding Machine Automation market The AEC 6910 can provide 1 2 PCI slots for expansion Therefore AEC 6910 s expandable function compact size combined with fanless design and highly efficient heat conduction mechanism can fulfill any rugged technical application in industrial automation factory control test instrumentation and safety surveillance Outstanding Over spec Design Intel s popular Pentium M processor with speeds of 1 6GHz up to 2 0GHz combined with fanless design and high performance is widely
2. 3 Exit the MB PnP Mode Set bit 1 of the configure control register Index 02h to 1 to exit the MB PnP Mode Appendix A Programming the Watchdog Timer A 3 Embedded Controller AEC 6910 WatchDog Timer Configuration Registers LDN Index R W Reset Configuration Register or Action Al 02H W N A Configure Control 07H 71H R W 00H WatchDog Timer Control Register 07H 72H R W 00H WatchDog Timer Configuration Regis ter 07H 73H R W 00H WatchDog Timer Time out Value Register Configure Control Indexz02h This register is write only Its values are not sticky that is to say a hardware reset will automatically clear the bits and does not require the software to clear them Bit Description 7 2 Reserved 1 Returns to the Wait for Key state This bit is used when the configuration sequence is completed 0 Resets all logical devices and restores configuration registers to their power on states Appendix A Programming the Watchdog Timer A 4 Embedded Controller AEC 6910 WatchDog Timer Control Register Indexz71h Default 00h Bit Description 7 WDT is reset upon a CIR interrupt 6 WDT is reset upon a KBC mouse interrupt 5 WDT is reset upon a KBC keyboard interrupt 4 WDT is reset upon a read or a write to the Game Port base address 3 2 Reserved 1 Force Time out This bit is self clearing 0 WDT Status 1 WDT value reaches 0 0 WDT value is not 0 WatchDog Timer Configuration Register
3. CALL Read Configuration Data CMP AL 87h JNE Not Initial MOV AL 21h CALL Read Configuration Data CMP AL 12h JNE Not Initial Need Initial STC RET Not Initial CLC RET Check Chip ENDP Read Configuration Data PROC NEAR MOV DX WORD PTR CS Cfg_Port 04h OUT DX AL Appendix A Programming the Watchdog Timer A 8 Embedded Controller AEC 6910 MOV DX WORD PTR CS Cfg Port 06h IN AL DX RET Read Configuration Data ENDP Write Configuration Data PROC NEAR MOV DX WORD PTR CS Cfg_Port 04h OUT DX AL XCHG AL AH MOV DX WORD PTR CS Cfg_Port 06h OUT DX AL RET Write Configuration Data ENDP Superio Set Reg proc near push ax MOV DX WORD PTR CS Cfg_Port 04h mov al cl out dx al pop ax inc dx out dx al ret Superio_Set_Reg endp Set_Logic_Device proc near Set Logic Device proc near Appendix A Programming the Watchdog Timer A 9 Embedded Controller AEC 6910 push ax push cx xchg al cl mov cl 07h call Superio Set Reg pop cx pop ax ret Set Logic Device endp Select 02Eh gt Index Port 02Fh gt Data Port Cfg_Port DB 087h 001h 055h 055h DW 02Eh 02Fh END Main Note Interrupt level mapping OFh Dh not valid OCh IRO12 03h IRQ3 02h not valid 01h IRQ1 00h no interrupt selected Appendix A Programming the Watchdog Timer A 10 Embedded Controller AEC 6910 Appendix I O Information Appendix B I O Information B 1 Embedded Controller AEC 6910 B 1 I O Address Map
4. DC 30VDC 2 AC Input External Power Adapter Optional Input voltage 100V AC 240V AC 50 60Hz e System Control Power on off switch x 1 Reset button x 1 e Indicators Power LED x 1 HDD active LED x 1 Mechanical and Environmental e Construction Rugged Aluminum Alloy chassis Color mustard e Mounting Wallmount Desktop e Dimension 1 PCI 214mm W x 94 75mm H x 237 8mm D 2 PCI 214mm W x 117 5mm H x 237 8mm D e Net Weight 1 PCI 12 41Ib 5 63kg 2 PCI 13 69lb 6 21kg e Gross Weight 21 21lb 9 62kg e Operating Temperature 5 F 131 F 15 C 55 C P M 1 6GHz CFD 5 F 122 F 15 C 50 C Chapter 1 General Information 1 6 Embedded Controller AEC 6910 e Operating Humidity e Vibration e Shock e EMC P M 1 6GHz Automotive HDD 5 F 113 F 15 C 45 C P M 1 6GHz Normal HDD 5 95 40 C non condensing 5grms 5 500Hz random operation CFD 1g 5 500Hz random operation HDD 50g peak acceleration 11 msec duration 20g peak acceleration 11 msec duration HDD CE FCC class B Chapter 1 General Information 1 7 Embedded Controller AEC 6910 Front Side HDD LED USB 2 0 Port x 4 Power LED Reset Power Switch Compact Flash card slot PCMCIA x 2 Rear Side Ethernet Audio ZEE 4 Serial ports Power Inlet Print port 1 KB and 1 Mouse eo PCI slot 2 PCI slots Available Chapter 1 General Information 1 8 Embedded Co
5. Mill Input output IO 00000000 0000000F Direct memory access controller M 00000020 00000021 Programmable interrupt controller 00000022 0000003F PCI bus 00000040 00000043 System timer 00000044 00000047 PCI bus 0000004C 0D00006F PCI bus 00000060 00000060 PC AT Enhanced PS 2 Keyboard 101 102 Key 00000061 00000061 System speaker 00000064 00000064 PC AT Enhanced P5 2 Keyboard 101 102 Key 00000070 00000071 System CMOSfreal time clock 00000072 0000007F PCI bus 00000081 00000083 Direct memory access controller 00000087 00000087 Direct memory access controller 00000089 00000088 Direct memory access controller 0000008F 00000091 Direct memory access controller 00000090 00000091 PCI bus 00000093 Q000009F PCI bus 00000040 000000A1 Programmable interrupt controller 00000042 OOODOOBF PCI bus 000000C0 000000DFJ Direct memory access controller 000000E0 000000EFJ PCI bus 000000F0 OOOODOFF Numeric data processor 00000100 OOODOCF PCI bus 00000170 00000177 Secondary IDE Channel 000001FO 000001F7 Primary IDE Channel 00000274 00000277 ISAPNP Read Data Port M 00000279 00000279 ISAPNP Read Data Port Y 000002E8 000002EF Communications Port COM4 E 000002F8 000002FF Communications Port COM2 3 00000376 00000376 Secondary IDE Channel 00000378 0000037F Printer Port LPT1 00000380 00000388 Intel R 82852 82855 GM GME Gr
6. acceptable and dependable in this market USB 2 0 Ethernet and 4 Serial ports allow communication with diverse devices with a high transfer rate Furthermore the AEC 6910 can concurrently support three tiers of expansion interfaces PCI PCMCIA and mini PCI These interfaces are fully integrated within the BOXER series and allow an upgrade to their usefulness It is a leading edge thermal and vibration design up to 60 degree operation and 5G RMS vibration and also an innovation for Machine Automation in the IPC industry AEC 6910 plays a role in connecting all subsystems in common applications Chapter 1 General Information 1 2 Embedded Controller AEC 6910 AAEON not only enhances your competitive value but also gives you an excellent solution for the future Strict Quality Control Process AAEON retains the perfect product design and management team Our Quality Control through multiple level experience and test has earned a good reputation in IPC field AAEON s whole product series are subjected to high level standards which make them our best guarantee and assurance to customers Excellent product quality will always be AAEON s best advertisement 24 hour FAE System AAEON s e RMA and e FAE 24 hour a day systems for all customers prompt request was formally launched in 2005 No matter if it is a holiday or weekend we can handle all kinds of requests and give you a satisfactory response in 10 days AAEON is proud of our quic
7. rear panel Chapter 2 Hardware Installation 2 10 AEC 6910 2 4 Wallmount kit Installation Step 1 Get the brackets ready and fasten appropriate four screws on each bracket Step 2 After fastening the two brackets on the bottom lid of AEC 6910 the wallmount kit installation is finished Chapter 2 Hardware Installation 2 11 Embedded Controller AEC 6910 Chapter Award BIOS Setup Chapter 3 Award BIOS Setup 3 1 Embedded Controller AEC 6910 3 1 System Test and Initialization These routines test and initialize board hardware If the routines encounter an error during the tests you will either hear a few short beeps or see an error message on the screen There are two kinds of errors fatal and non fatal The system can usually continue the boot up sequence with non fatal errors Non fatal error messages usually appear on the screen along with the following instructions Press lt F1 gt to RESUME Write down the message and press the F1 key to continue the boot up sequence System configuration verification These routines check the current system configuration against the values stored in the CMOS memory If they do not match the program outputs an error message You will then need to run the BIOS setup program to set the configuration information in memory There are three situations in which you will need to change the CMOS settings 1 You are starting your system for the first ti
8. twice and tick the Specify a location option Click Next and choose a route where you want place the folders on before you click on Open Chapter 4 Drivers Installation 4 3 Embedded Controller AEC 6910 6 Click Next Yes Finish and the window will show you how to finish the installation process Step 4 Install Audio Driver 1 Click on the Audio Driver folder and then double click on the setup exe 2 Follow the instructions that the window will show you 3 The system will help you install the driver automatically Note Under the Window OS environment if the CRT connector is connected to display monitor by the data switch device the user need to set the color and resolution from Intel Graphic utility VGA driver instead of setting from the control panel in case of the wrong display appearance Chapter 4 Driver Installation 4 4 Embedded Controller AEC 6910 Appendix Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A 1 Embedded Controller AEC 6910 A 1 Programming AEC 6910 utilizes the ITE 8712 chipset as its watchdog timer controller Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached with which you can develop a customized program to fit your application Configuring Sequence Description After the hardware reset or power on reset the ITE 8712 enters the normal mode with all logical devices d
9. 420 CardBus Controller Appendix B I O Information B 2 Embedded Controller AEC 6910 B 2 Memory Address Map Mili Memory 00000000 OOO9FFFF System board M 00040000 ODOBFFFF Intel R 82852 82855 GM GME Graphics Controller m 00040000 OOOBFFFF PCI bus m 000CC800 OOOCFFFF PCI bus m 00004000 OOODFFFF PCI bus ODDDEODO ODODEFFF Texas Instruments PCI 1420 CardBus Controller 000DF000 ODODFFFF Texas Instruments PCI 1420 CardBus Controller m 000F0000 ODOF3FFF Motherboard resources m 000F4000 OOOF7FFF Motherboard resources m 000F8000 ODOFBFFF Motherboard resources m 000FCOOO ODOFFFFF Motherboard resources m 00100000 OOFFFFFF System board OEODDOOD FEBFFFFF PCI bus um 08000000 DFFFFFFF Intel R 82852 82855 GM GME Graphics Controller 0000000 E7FFFFFF Intel R 82852 82855 GM GME Graphics Controller SF Es000000 ESO1FFFF Intel R 8255xER PCI Adapter E8030000 ESO30FFF Texas Instruments PCI 1420 CardBus Controller E8035000 E8035FFF Texas Instruments PCI 1420 CardBus Controller Big Es034000 ESO3AFFF Intel R 8255xER PCI Adapter ma EG100000 EB17FFFF Intel R 82852 82855 GM GME Graphics Controller E8180000 EB1FFFFF Intel R 82852 82855 GM GME Graphics Controller E8200000 EB2003FF Intel r 82801DB DBM USB Enhanced Host Controller E8201000 ES2011FF Realtek AC 97 Audio E8202000 E82020FF Realtek AC 97 Audio FE600000 FE7F
10. DB DBM USB Universal Host Controller 24C4 ag PCI 9 Intel R 82852 82855 GM GME Graphics Controller PCI 9 Texas Instruments PCI 1420 CardBus Controller B 4 DMA Channel Assignments cw MM M amp 2 Standard floppy disk controller m 4 Direct memory access controller Appendix B I O Information B 4
11. DD power down power on by ring KB wake up etc PnP PCI Configurations This entry appears if your system supports PnP PCI PC Health Status This menu allows you to set the shutdown temperature for your system Frequency Voltage Control Use this menu to specify your settings for auto detect DIMM PCI clock and spread spectrum Load Fail Safe Defaults Use this menu to load the BIOS default values for the minimal stable performance for your system to operate Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations While AWARD has designated the custom BIOS to maximize performance the factory has the right to change these defaults to meet their needs Set Supervisor User Password Use this menu to set Supervisor User Passwords Chapter 3 Award BIOS Setup 3 4 Embedded Controller AEC 6910 Save and Exit Setup Save CMOS value changes to CMOS and exit setup Exit Without Saving Abandon all CMOS value changes and exit setup You can refer to the AAEON BIOS Item Description pdf file in the CD for the meaning of each setting in this chapter Chapter 3 Award BIOS Setup 3 5 Embedded Controller AEC 6910 Chapter Driver Installation Chapter 4 Driver Installation 4 1 Embedded Controller AEC 6910 The AEC 6910 comes with a CD ROM that contains all drivers and utilities that meet your needs Follow the sequence below to instal
12. Embedded Controller AEC 6910 AEC 6910 Fanless Embedded Controller Intel Pentium M Celeron M Processor With 1 2 PCI slots PCMCI 4 COMs Audio CompactFlash AEC 6910 Manual 2nd Ed June 2007 Embedded Controller AEC 6910 Copyright Notice This document is copyrighted 2007 All rights are reserved The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of the original manufacturer Information provided in this manual is intended to be accurate and reliable However the original manufacturer assumes no responsibility for its use or for any infringements upon the rights of third parties that may result from its use The material in this document is for product information only and is subject to change without notice While reasonable efforts have been made in the preparation of this document to assure its accuracy AAEON assumes no liabilities resulting from errors or omissions in this document or from the use of the information contained herein AAEON reserves the right to make changes in the product design without notice to its users Embedded Controller AEC 6910 Acknowledgments All other products name or trademarks are properties of their respective owners Award is a trad
13. FFFF Texas Instruments PCI 1420 CardBus Controller FES00000 FESFFFFF Texas Instruments PCI 1420 CardBus Controller FEBFDODO FEBFDFFF Texas Instruments PCI 1420 CardBus Controller FEBFEODO FEBFEFFF Texas Instruments PCI 1420 CardBus Controller FEBFFCOD FEBFFFFF Intel R 82801DB Ultra ATA Storage Controller 24CB El FECDDDOD FECOFFFF System board Bl FEEOOODO FEEOFFFF System board m FFBODODO FFB7FFFF System board m FFB80000 FFBFFFFF Intel r 82802 Firmware Hub Device E FFFODODD FFFFFFFF System board Appendix B I O Information B 3 Embedded Controller AEC 6910 B 3 IRQ Mapping Chart Hnterrupt request IRO Bl 158 0 System timer ISA 1 PC AT Enhanced PS 2 Keyboard 101 102 Key y ISA 3 Communications Port COM2 J ISA 4 Communications Port COM1 23 ISA 6 Standard Floppy disk controller M ISA 8 System CMOS real time clock Y ISA 10 Communications Port COM3 4 ISA 11 Communications Port COM4 9 ISA 12 Logitech PS 2 Port Mouse m 15 13 Numeric data processor 3 154 14 Primary IDE Channel 3 154 15 Secondary IDE Channel PCI 5 Intel r 82801DB DBM USB Enhanced Host Controller Big PCI 5 Intel R 8255xER PCI Adapter PCI 5 Intel R 82801DB DBM SMBus Controller 24C3 PCI 5 Realtek AC 97 Audio PCI 5 Texas Instruments PCI 1420 CardBus Controller PCI 9 Intel R 82801DB DBM USB Universal Host Controller 24C2 PCI 9 Intel R 82801
14. Index 72h Default 00h Bit Description 7 WDT Time out value select 1 Second 0 Minute 6 WDT output through KRST pulse enable 5 4 Reserved 3 0 Select the interrupt level e for WDT WatchDog Timer Time out Value Register Indexz73h Default 00h Bit 7 0 Description WDT Time out value 7 0 Appendix A Programming the Watchdog Timer A 5 Embedded Controller AEC 6910 A 2 IT8712 Watchdog Timer Initial Program MODEL SMALL CODE Main CALL Enter Configuration mode CALL Check Chip mov cl 7 call Set Logic Device time setting mov cl 10 10 Sec dec al Watch Dog Setting Timer setting mov al cl mov cl 73h call Superio Set Reg Clear by keyboard or mouse interrupt mov al OfOh mov cl 71h call Superio Set Reg unit is second mov al OCOH mov cl 72h call Superio_Set_Reg Appendix A Programming the Watchdog Timer A 6 Embedded Controller AEC 6910 game port enable mov cl 9 call Set Logic Device Initial OK CALL Exit Configuration mode MOV AH 4Ch INT 21h Enter Configuration Mode PROC NEAR MOV SI WORD PTR CS Offset Cfg Port MOV DX 02Eh MOV CX 04h Init 1 MOV AL BYTE PTR CS SI OUT DX AL INC SI LOOP Init 1 RET Enter Configuration Mode ENDP Exit Configuration Mode PROC NEAR MOV AX 0202h CALL Write Configuration Data Appendix A Programming the Watchdog Timer A 7 Embedded Controller AEC 6910 RET Exit Configuration Mode ENDP Check Chip PROC NEAR MOV AL 20h
15. Protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before connecting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient over voltage Never pour any liquid into an opening This could cause fire or electrical shock Never open the equipment For safety reasons only qualified service personnel should open the equipment If any of the following situations arises get the equipment checked by service personnel a The power cord or plug is damaged b Liquid has penetrated into the equipment c The equipment has been exposed to moisture Embedded Controller AEC 6910 d The equipment does not work well or you cannot get it to work according to the user s manual e The equipment has been dropped and damaged f The equipment has obvious signs of breakage 15 DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW 20 C 4 F OR ABOVE 60 C 140 F IT MAY DAMAGE THE EQUIPMENT FCC Safety This device complies with Part 15 FCC Rules Warning Operation is subject to the following two conditions 1 this device may not cause harmful interferenc
16. aphics Controller 000003C0 ODODO3DF Intel R 82852 82855 GM GME Graphics Controller 000003E8 DDDDD3EF Communications Port COM3 000003F0 000003F5 Standard floppy disk controller 2 000003F6 000003F6 Primary IDE Channel 2 000003F7 000003F7 Standard floppy disk controller y 000003F8 ODDDD3FF Communications Port COM1 00000500 0000051F Intel R 82801DB DBM SMBus Controller 24C3 00000778 0000077FJ Printer Port LPT1 00000479 00000479 ISAPNP Read Data Port 00000000 OODOFFFF PCI bus 0000D000 OOQODOSF Intel R 8255xER PCI Adapter ODDOEODO OOODEO1F Intel R 82801DB DBM USB Universal Host Controller 24C2 0000E100 0000E11F Intel R 82801DB DBM USB Universal Host Controller 24C4 DODOE200 0D00E207 Intel R 82852 82855 GM GME Graphics Controller 0000E400 OOODE4FF Realtek AC 97 Audio 0000E500 DDDDES3F Realtek AC 97 Audio 3 ODDOFODD OODOFOOF Intel R 82801DB Ultra ATA Storage Controller 24CB e 0000FBOO DDDDFBFF Texas Instruments PCI 1420 CardBus Controller 0000FCOD 0000FCFF Texas Instruments PCI 1420 CardBus Controller 0000FDFC OODOFDFD Texas Instruments PCI 1420 CardBus Controller 2 ETTE RR 88 C UB GS UR a CACA OO 0000FDFE OODOFDFF Texas Instruments PCI 1420 CardBus Controller 0000FE00 DODOFEFF Texas Instruments PCI 1420 CardBus Controller OOOOFFOO DODOFFFF Texas Instruments PCI 1
17. e and 2 this device must accept any interference received including interference that may cause undesired operation Caution There is a danger of explosion if the battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions and your local government s recycling or disposal directives Embedded Controller AEC 6910 Below Table for China RoHS Requirements in PHA EMEL ANK EL AAEON Boxer Industrial System ABA EW E TBE FR 44 K fa ANR ERKE SRAM Pb Hg Cd Cr VI PBB PBDE EP ji FEL ERR x O O O O O KRATA AME x O O O O O FER RAM 55 x O O O O O rp de REESE x O O O O O 5A Wea O O O O O FER O O O O O O RNBABA AYMARA OEA E ETE SJ T 11363 2006 ERLE ERES LU e X dex SEG SYWRESEBMENR WEE PN EGER HH SJ T 11363 2006 FR ERREAK Ai KP TARR REI ARRE ME RAR E SS ARA PWT PEEL AUREA AA vi Embedded Controller AEC 6910 Contents Chapter 1 General Information 1 1 Introduction e eeeuu ueu LL LL LL LL Nu 1 2 12 ESAS ii o 1 4 LIS PecifiCatiOOS rra 1 5 Chapter 2 Hardware Installation 2 1 Dimensio crm 2 2 2 2HardDiskDrivelnstallation 2 4 2 3PC1Cardinstallation 2 8 24WallmountKitinstallation
18. emark of Award Software International Inc CompactFlash is a trademark of the Compact Flash Association Intel Pentium 4 and Celeron D are trademarks of Intel Corporation Microsoft Windows is a registered trademark of Microsoft Corp PC AT PS 2 and VGA are trademarks of International Business Machines Corporation All other product names or trademarks are properties of their respective owners Embedded Controller AEC 6910 Packing List Before you begin operating your PC please make sure that the following materials are enclosed 1 AEC 6910 Embedded Controller 1 Phoenix Power Connector 2 Wallmount Brackets 1 Audio Cable 1 Screw Package 1 CD ROM for manual in PDF format and drivers If any of these items should be missing or damaged please contact your distributor or sales representative immediately ili Embedded Controller AEC 6910 Safety amp Warranty Read these safety instructions carefully Keep this user s manual for later reference Disconnect this equipment from any AC outlet before cleaning Do not use liquid or spray detergents for cleaning Use a damp cloth For pluggable equipment the power outlet must be installed near the equipment and must be easily accessible Keep this equipment away from humidity Put this equipment on a firm surface during installation Dropping it or letting it fall could cause damage The openings on the enclosure are for air convection
19. he HDD Module Step 2 Place the bumpers at the four indentations of the two sides of the HDD bracket Chapter 2 Hardware Installation 2 6 Embedded Controller AEC 6910 Step 3 Connect the power cable to the HDD module Step 4 Get the HDD cover ready and combine the HDD Bracket with the HDD cover fasten the four screws in the blue circles shown below E HDD Cover Step 5 Close the HDD cover and fasten the five screws on the HDD cover Close the bottom lid of the AEC 6910 and fasten six screws on the bottom lid the HDD installation is now finished Chapter 2 Hardware Installation 2 7 Embedded Controller AEC 6910 2 3 PCI Card Installation Step 1 Unfasten the two screws on the rear panel Chapter 2 Hardware Installation 2 8 Embedded Controller AEC 6910 Step 4 Remove the screw with your finger figure 1 and get the PCI card ready to install You should keep the shield and screw for use later Screw PCI Slot shield Figure 1 Step 5 Insert the PCI card into the PCI slot and reattach the screw Chapter 2 Hardware Installation 2 9 Embedded Controller AEC 6910 Step 6 Unfasten the screws Figure 1 and push the tenon to lock the PCI card in position Figure 2 Figure 1 Figure 2 Step 7 Close the bottom lid of the AEC 6910 and fasten six screws on bottom lid Step 8 Fasten the three screws on the front panel and the two screws on the
20. isabled except KBC The initial state enable bit of this logical device KBC is determined by the state of pin 121 DTR1 at the falling edge of the system reset during power on reset Hardware Reset Wait for key string VO write to 2Eh N Is the data 87h Y gt m VO write to 2Eh N Next Data Y Any other I O transition cyce Any other I O transition cycle N Last Data Y MB PnP Mode Appendix A Programming the Watchdog Timer A 2 Embedded Controller AEC 6910 There are three steps to complete the configuration setup 1 Enter the MB PnP Mode 2 Modify the data of configuration registers 3 Exit the MB PnP Mode Undesired result may occur if the MB PnP Mode is not exited normally 1 Enter the MB PnP Mode To enter the MB PnP Mode four special I O write operations are to be performed during Wait for Key state To ensure the initial state of the key check logic it is necessary to perform four write opera tions to the Special Address port 2EH Two different enter keys are provided to select configuration ports 2Eh 2Fh of the next step Address Port Data Port 87h 01h 55h 55h 2Eh 2Fh 2 Modify the Data of the Registers All configuration registers can be accessed after entering the MB PnP Mode Before accessing a selected register the content of Index 07h must be changed to the LDN to which the register belongs except some Global registers
21. k service and professional teamwork to provide our customers with continual support Great design great value and great service are hallmarks of the AAEON BOXER embedded control PCs There really is no other choice for your application than AAEON if you want the best performance and best value Chapter 1 General Information 1 3 Embedded Controller AEC 6910 1 2 Features e Fanless Design with Intel Pentium M Celeron M Processors e Supports 1 or 2 PCI slots for expansion e 2POMCIA e 4COM USB 2 0 Ethernet e Operating Temperature 15 C 50 C e Anti vibration up to 5grms Anti shock up to 50 g Chapter 1 General Information 1 4 Embedded Controller AEC 6910 1 3 Specifications System e CPU e System Memory e Expansion e VGA e Keyboard Mouse Ethernet e SSD e Device Bay e Serial Port e Audio e Parallel Port e USB e Watchdog Timer e Power Supply Intel Pentium M Celeron M Processor DDR RAM DIMM x 1 Max 1GB PCI slot x 1 Optional 2 PCI POMCIA x 2 DB 15 VGA connector PS 2 Keyboard amp Mouse 10 100Base TX RJ 45 Connector x 1 CompactFlash slot x 1 Internal 2 5 HDD Bay 4 x RS 232 Line in Line out MIC in Parallel Port x 1 4 USB 2 0 ports Generates a time out System reset setting via software 1 DC Input Internal DC DC Converter Default Input voltage Chapter 1 General Information 1 5 Embedded Controller AEC 6910 9V
22. l the drivers Step 1 Install INF Driver Step 2 Install VGA Driver Step 3 Install LAN Driver Step 4 Install Audio Driver USB 2 0 Drivers are available for download using Windows Update for both Windows XP and Windows 2000 For additional information regarding USB 2 0 support in Windows XP and Windows 2000 please visit www microsoft com hwdev usb Please read instructions below for further detailed installations Chapter 4 Driver Installation 4 2 Embedded Controller AEC 6910 4 1 Installation Insert the AEC 6910 CD ROM into the CD ROM Drive The Autorun program will run automatically You also can choose the drivers to install from step 1 to step 4 in order as following instructions Step 1 Install INF Driver 1 Click on the INF Driver folder and then double click on the setup exe 2 Follow the instructions that the window will show you 3 The system will help you install the driver automatically Step 2 Install VGA Driver 1 Click on the VGA Driver folder and then double click on the setup exe 2 Follow the instructions that the window will show you 3 The system will help you install the driver automatically Step 3 Install LAN Driver 1 Click on Start button Settings Control Panel System 2 Select Device Manager under the Hardware category Double click on the Ethernet controller and select reinstall Driver button under the General category 4 Click Next
23. me 2 You have changed the hardware attached to your system 3 The CMOS memory has lost power and the configuration information has been erased The AEC 6910 CMOS memory has an integral lithium battery backup for data retention However you will need to replace the complete unit when it finally runs down Chapter 3 Award BIOS Setup 3 2 AEC 6910 3 2 Award BIOS Setup Awards BIOS ROM has a built in Setup program that allows users to modify the basic system configuration This type of information is stored in battery backed CMOS RAM so that it retains the Setup information when the power is turned off Entering Setup Power on the computer and press Del immediately This will allow you to enter Setup Phoenix AwardBIOS CMOS Setup Utility Esc Quit Select Item F10 Save Exit Setup Standard CMOS Features Use this menu for basic system configuration Date time IDE etc Advanced BIOS Features Use this menu to set the advanced features available on your system Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system performance Chapter 3 Award BIOS Setup 3 3 Embedded Controller AEC 6910 Integrated Peripherals Use this menu to specify your settings for integrated peripherals Primary slave secondary slave keyboard mouse etc Power Management Setup Use this menu to specify your settings for power management H
24. ntroller AEC 6910 Chapter Hardware Installation Chapter 2 Hardware Installation 2 1 Embedded Controller AEC 6910 2 1 Dimension A 1 PCI slot version TI mimm Hme3 nmi M U cd 1 gt la HE rd y l 1 aso LIL V M y NI HU 3 JL LLW mn o DES Y Chapter 2 Hardware Installation 2 2 Embedded Controller AEC 6910 B 2 PCI slots version 5 Chapter 2 Hardware Installation 2 3 Embedded Controller AEC 6910 2 2 Hard Disk Drive Installation 2 2 1 Disassemble the AEC 6910 For Hard Disk Drive HDD installation you have to disassemble the bottom lid of AEC 6910 and some components and covers in the AEC 6910 Step 1 Unfasten the two screws on the rear panel Chapter 2 Hardware Installation 2 4 Embedded Controller AEC 6910 Step 3 Unfasten the six screws on the bottom lid Step 4 Take off the bottom lid and loosen the two screws on the riser card and remove the riser card Riser card Step 5 Unfasten the five screws and open the HDD cover HDD Cover Chapter 2 Hardware Installation 2 5 Embedded Controller AEC 6910 Step 6 Loosen the four screws on the HDD bracket HDD Bracket 2 2 2 Assemble the HDD Module After disassembling the AEC 6910 you have to get the HDD module ready for the proceeding installation Step 1 Get four pink rubber bumpers from the accessory kit and wrap them around the four screws on t

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents