4 - ABetter Pour
Contents
1. operations call only an authorised after sales service centre or contact your local Distributor UM_2013_40_enoliving_it 19 Rev 01 July 2013 enomatic wine serving systems 10 Maintenance and Cleaning A frequent and severe dispensing tap cleaning is necessary to maintain your Enomatic Wine Serving System in full performances and to grant wine flavours preservation 10 1 Daily Maintenance On a daily basis clean the Serving Spout by immersing it in water and then rinse thoroughly clean the bodywork with a non abrasive cloth drain or dry any eventual moisture from bottle chamber walls Consider that the dispenser is made from three different materials see sections 6 1 e STAINLESS STEEL clean it with a soft and non abrasive cloth and using special products for steel e BAYDUR clean it with a soft and non abrasive cloth and using special products e RUBBER CARPET wash it in dishwasher or with water and detergent by using a toothbrush or a little sponge in order to remove the wine sediments inside the slots 10 2 Bottle tube and Tap cleaning Dispensing taps and internal straws must be cleaned EVERY 10 POURED BOTTLES PER DISPENSING POSITION please note the chart available at the end of this manual to be ticked at any bottle engagement for tracking An ideal time to clean the entire Bottle Tube and Tap is when a bottle is being changed act as follow e replacing the wine with a bottle co2. exerting pressure using your hands on the neck bottle base see the arrow on the image above in order to unlock the piston the piston and the bottle will rise up UM_2013_40_enoliving_it 16 Rev 01 July 2013 enomatic wine serving systems 5 Pay attention to the bottle neck it has to be placed properly on the tap seal 7 3 Wine priming After a new bottle inserting is suggested to pour a small quantity of wine in order to remove the oxygen inside the bottle itself Perform this operation in case of bottle opened since few hours out of the dispenser as well In case the dispenser would be set in free pouring press the pouring button for the time needed to pour a small quantity of wine in case the dispenser would be in pre set volume press the pouring button the wine will start to come out to supply the pre set quantity press again the button in order to terminate the pouring the second pressing in order to pour the smallest quantity of wine possible See section 8 1 related settings of the dispensers in free pouring or pre set volume In order to obtain best wine conditions environment temperature range must be within 10 C and 32 C 50 F 89 F and environment relative humidity between 5 and 70 Please note following chart for a complete resume 8 Change bottles Always keep your hands away from lifter motion area in order to avoid risk of injuries This function is to remove an empty b
3. Directive 2006 95 EC Directive regulation concerning the approach of State Members laws regarding the electric material destined to be used within certain voltage limits Direttive Compatibilit Elettromagnetica 2004 108 CE Direttiva concernente il ravvicinamento delle legislazioni degli Stati membri relativa alla compatibilit elettromagnetica Electro Magnetic Compatibility 2004 108 EC Directive regarding the approach of State Members laws concerning about electro magnetic compatibility Data di emissione Generalit e firma della persona autorizzata Date of issue Identity and signature of the person empowered 13 Presidente amp Amministratore Delegato President amp CEO enomatic s r l Via di Meleto Lorenzo Bencist Falorni 50027 Strada in Chianti FI P I 01066310523 UM_2013_40_enoliving_it 25 Rev 01 July 2013 enomatic wine serving systems STATEMENT OF WARRANTY WE Enomatic srl WARRANT that the Enomatic Wine Serving Systems the Goods models enoline enosystem enoround and enomove manufactured by Enomatic s r l are sold and delivered to the Purchaser free from manufacturing defects in materials and workmanship From the Installation Acceptance Date Enomatic the Company undertakes that the Warranty Shall cover free of charge to the Purchaser e the repair or replacement at the Company s sole discretion of any functionally inoperative PARTS that according to the Company s incontestable ju
4. The dispenser doesn t switch on Bottle engagement indicator s is are off Puring is not fluent Wine drops falling from the spouts Wine bubbles in the glass while pouring The bottle is not properly engaged One or both too short bottles were engaged and the sealing non the tap is not correct Canister tight is missing Power failure Switch is off Bottle is missing Internal straw is not properly inserted The filter at the bottom of the internal straw is stuck especially with sediment or aged wines Tank is almost empty or pressure is not enough Some wine sediments or cork pieces are blocking the tap Wine is falling on the bottom of the glass Check all the bottles trying to hear a whistle coming from the necks or wet your finger and surround them Check both the bottles are pushed upwards and tight against the seals Install cylindrical adapter between bottle and piston the bottle is too short Check the canister tigthening Plug the dispenser to a power supply Turn on the switch Engage the bottle Remove the bottle and fix it properly Remove the bottle and clean the filter Change the canister Pour citric acid solution to remove all the sediments Lean the glass towards the spout In case the problems remain please contact your local enomatic dealer Full list is available on www enomatic it For repairs and maintenance in case of faults or faulty
5. armonica apparecchiature A2 2009 con corrente di ingresso lt 16 A per fase Electromagnetic compatibility EMC Part 3 2 Limits Limits for harmonic current emissions equipment input current lt 16 A per phase Compatibilit elettromagnetica EMC Parte 3 3 Limiti EN 61000 3 Limitazione delle fluttuazioni di tensione e dei flicker in sistemi 3 2008 di alimentazione in bassa tensione per apparecchiature con corrente nominale lt 16 A Electromagnetic compatibility EMC Part 3 3 Limits Limitation of voltage fluctuations and flicker in low voltage supply systems for equipment with rated current lt 16 A EN 55014 2 1997 Compatibilit elettromagnetica Requisiti di immunit per A1 2001 apparecchi elettrodomestici utensili e degli apparecchi elettrici A2 2008 similari Parte 2 Immunit Norma di famiglia di prodotti UM_2013_40_enoliving_it 24 Rev 01 July 2013 enomatic wine serving systems Electromagnetic compatibility Requirements for household appliances electric tools and similar apparatus Part 2 Immunity Product family standard e quindi rispondente ai requisiti essenziali delle Direttive Also declares that it conforms with the requisite Directives Direttiva Bassa Tensione 2006 95 CE Direttiva concernente il ravvicinamento delle legislazioni degli Stati membri relativa al materiale elettrico destinato a essere utilizzato entro taluni limiti di tensione Low Voltage
6. 013
7. 1 19 50027 Strada in Chianti FI Italy dichiariamo sotto la nostra responsabilit che l apparecchio declare under our responsibility that the apparatus al quale questa dichiarazione si riferisce conforme alle seguenti norme to which this declaration relates is in conformity with the following standards CEI EN 60335 Sicurezza degli apparecchi elettrici di uso domestico e similare 1 2001 Fourth Sicurezza Parte 1 Norme generali Edition Household and similar electrical appliances Safety Part 1 A1 2004 A2 General requirements 2006 incl Corrigendum 1 2006 CEI EN 60335 2 Sicurezza degli apparecchi elettrici d uso domestico e similare 75 2002 Second Sicurezza Parte 2 Norme particolari per distributori Edition commerciali e apparecchi automatici per la vendita A1 2004 Household and similar electrical appliances Safety Part 2 A2 2008 Particular requirements for commercial dispensing appliances and vending machines EN 55014 1 2006 Compatibilit elettromagnetica Prescrizioni per gli A1 2009 elettrodomestici gli utensili elettrici e gli apparecchi similari A2 2011 Parte 1 Emissione Norma di famiglia di prodotti Electromagnetic compatibility Requirements for household appliances electric tools and similar apparatus Part 1 Emission Product family standard EN 61000 3 Compatibilit elettromagnetica EMC Parte 3 2 Limiti 2 2006 A1 2009 Limiti per le emissioni di corrente
8. 7 Inserting the Bottle TUPDe ic nai 7 LOANO Ne DOUG ee a Change DOES 17 8 VOLIT O rino ia Troubleshooting 1r srrreiiie siii 19 O Maintenance and Cleaning rei 20 a F pa Daily Maintenance 10 2 Bottle tube and Tap cleaning 10 3 Extraordinary maintenance 11 Technical CharacteristicsS rr 22 11 1 Equipment Not included IMPORTANT NOTICE FOR THE USER rrr c erre 23 DICHIARAZIONE CE DI CONFORMITA 24 STATEMENT OF WARRANTY 26 UM_2013_40_enoliving_it 3 Rev 01 July 2013 enomatic wine serving systems 1 Warnings Before operating the Enomatic Wine Serving System carefully read the instructions contained in this Operating Manual and all other documentation you received 1 oe 10 During operation it is essential to pay attention to these safety requirements to avoid the risk of fire electric shocks or other incidents Do not immerse the electrical cord plugs or the Enomatic model in water or any other liquid This appliance can be used and cleaned by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given Supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children should be supervised t
9. anty the Company may charge the Purchaser for all reasonable costs and expenses incurred by the Company in the course of or in consequence of such investigation Without prejudice to the foregoing the Company reserves the right to charge for travelling time and incidental expenses incurred in respect of attendance at your premises to investigate and rectify any problem reported by you The Company s obligations under the Warranty are contingent upon the Company s agents or servants being given full details of the defects without delay and adequate time and access to the Goods during normal working hours to rectify such defect If the Company rectifies the defect within a reasonable period of time then the Company will have no other liability in any respect of or arising from such defect The above Warranty does not extend to parts materials or equipment not manufactured by Enomatic s r l in respect of which the Purchaser will only be entitled to the benefit of any such warranty or guarantee as is given by the supplier or service provider to the Company enomatic s r l Amministratore Delegato Lorenzo Bencista Falorni i we HEY Code and serial number ruuna Pet i A V UM_2013_40_enoliving_it 27 Rev 01 July 2013 enomatic wine serving systems Produced by Enomatic S R L Via di Meleto 1 19 Greve in Chianti Fl ltaly Distribuited by For service contact UM_2013_40_enoliving_it 28 Rev 01 July 2
10. ar information concerning any technical aspects and to facilitate the replacement of parts AVOID DAMAGE OR REMOVAL OF THE DATA LABEL Example Product code and description Production week Serial number RAEE Power tension Power consumption Frequency Electrical warning Read the user manual UM_2013_40_enoliving_it 6 Rev 01 July 2013 enomatic wine serving systems Suitable for dry location only Example of a label for US and Canada market Example of a label for Mexican market UM_2013_40_enoliving_it Rev 01 July 2013 enomatic wine serving systems 4 Transportation and storage Because of the weight and size of the Enomatic models be careful for transportation To avoid damages on the Enomatic model it is necessary to take big care during loading and unloading operations It is necessary to lift according to the symbol found on the cardboard package It is important that the Enomatic models are not placed on top of each other and that the right vertical position indicated by arrows on the package is maintained at all times Avoid shaking or turning the Enomatic models upside down Place Enomatic dispensers in dry environment with external temperature between 10 C and 32 C and with external humidity not more than 60 5 Unpack When you removed the packaging check that the Enomatic model has not been damaged during transport If you have any doubts do not operate the Enomatic mode
11. clean water and flush the Bottle Tube and Tap with the water serve approximately 200mls e insert a bottle without internal straw and perform some supplies in order to remove completely the water from the tap Replace the water with a new bottle of the wine to be served and supply Execute an intense cleaning before leaving your Enomatic Wine Serving System not operative for longer than three days Please note that dispensing sweet or particularly aged wines may result into severe wine deposit inside the ducts Intensify cleaning through citric acid solutions in case UM_2013_40_enoliving_it 21 Rev 01 July 2013 enomatic wine serving systems 11 Technical Characteristics Enoliving Enoliving USA _ Model Enoliving USA Size mm vesti oa s Frequency Electrical Hz armors wats O Ta a Fuses A Max cylinder pressure Bar 11 1 Equipment Not included 1 Foodgrade Argon canister E938 maximum height 30cm joint M11x1 2 Adapter for short bottles place it on the existing transfer UM_2013_40_enoliving_it 22 Rev 01 July 2013 D enomatic wine serving systems 3 joint for the connection of the dispenser to an external cylinder cylinder can be Argon or Nitrogen without distinction IMPORTANT NOTICE FOR THE USER As prescribed by Art 13 D L 151 July 25 2005 Attuazione delle Direttive 2002 95 CE 2002 96 CE e 2003 108 CE relative alla riduzione del
12. dgement are deemed to be defective in workmanship or materials because of a manufacturing defect detected within the first 12 months excluding software e the diagnosis and elimination of any errors found in the SOFTWARE programmes provided that the errors are recurrent and documented by way of supply of new corrected versions of the software for the first 6 months e the warranty shall include only the replacement of those defective parts and shall not include LABOUR This is the Company s entire liability in respect of such Warranty Enomatic shall provide warranty services directly or through its own authorized repair centres Materials covered by warranty must be sent to the Repair Centres free of charge for enomatic and shall be sent back at the customer s expense Any parts replaced shall remain the property of enomatic The Purchaser must save proof of the Installation Acceptance date as detailed on the Installation Acceptance Certificate together with the sales receipt or invoice stating the item numbers of the purchased Goods All claims for Goods under Warranty shall be forwarded to the Company together with proof of the Installation Acceptance date and a copy of this Statement of Warranty In the event that installation of the Goods is delayed by the Purchaser for more than 1 month from the original date of delivery of the Goods as requested by the Purchaser then the Installation Acceptance date shall be deemed to commence 1 mon
13. ecification supplied by the Purchaser g wilful or accidental damage misuse abuse or negligence h any modification whether by alteration deletion addition repair or otherwise to the Goods by the Purchaser or any other unauthorised persons unless the Purchaser has obtained the prior written consent of the Company If any such unauthorised modification is made then without prejudice to the Company s other rights and remedies the Warranty will be null and void i the use of any spare parts that are not originals as supplied by the Company j if the original identification markings on the Goods have been removed defaced or altered UM_2013_40_enoliving_it 26 Rev 01 July 2013 enomatic wine serving systems The Company will be under no liability under the above Warranty or any other warranty condition or guarantee a if the total price for the Goods has not been paid by the Purchaser by the due date for payment b for any indirect incidental or consequential loss damage cost or expense of any kind whatsoever whether arising under an accident contracts tort including negligence or otherwise c for compensation for any reasons whatsoever resulting from any inoperative down time of the Goods including any loss of wine or other beverage d If the labels or marks are removed from the machines If a defect or failure of the Goods is found upon investigation not to be the Company s responsibility under this Warr
14. enomatic wine serving systems enoliving Enoliving room temperature User s Manual Translation of the original instructions UM 40_ 2013 Rev 01 July 2013 Enomatic srl Via di Meleto 1 19 I 50027 Greve in Chianti Firenze Italy Tel 39 055 8547272 Fax 39 055 8547807 www enomatic it UM_2013_40_enoliving_it 21 2 Rev 01 July 2013 enomatic wine serving systems WARNING Should warranty terms be applied please return the product included original packing all accessories and documentation i e user s manual ATTENZIONE Nei casi in cui l applicazione della garanzia preveda la restituzione del prodotto il bene dovr essere restituito dal cliente nella confezione originale completa di tutte le sue parti compresi imballo eventuale documentazione ed accessori manuale di istruzioni UM_2013_40_enoliving_it Ze Rev 01 July 2013 enomatic wine serving systems INDEX WAT RIN IN Goatees tcc air ri dig di di ad ir 2 ATTENZIONE E 2 Warnia S aa E E 4 INnEFOauctioni acli 6 Model Identification ccccccececeeseeeecenseeseenseeecenseeseenseeseenneeseoaaes 6 Transportation and storage ccccceeesseeeeeeseeseenseeseeeneeeseeneeesees 8 UNPAacK cca 8 Installation einen E E E 9 Parts of the Enomatic Wine Serving System Electrical supply Gas COMICO Operating instructions s nsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnnm 14 OY OY D POT ONTNYNET AUR WN
15. he canister will completely finish the bottles led start to blink see image below related to the bottles led it will be possible to pour some other supplies before the complete emptying BOTTLES LED Use certified FOODGRADE Argon E938 UM_2013_40_enoliving_it 13 Rev 01 July 2013 enomatic wine serving systems 7 Operating instructions Plug the electrical cord to the socket Turn on the dispenser selecting ON the main switch 1 7 1 Inserting the Bottle Tube Insert the Bottle Tube into the centre of each Tap by pushing it firmly to create a secure fit see images below The Bottle Tube has a filter to prevent sediment from red wines entering the Tap valve Rev 01 July 2013 UM_2013_40_enoliving_it 14 enomatic wine serving systems 7 2 Loading the bottle 1 Press the cylinder downwards until it is blocked 2 Before bottle positioning place the curvy plastic coaster on the cylinders We suggest to place the curvy coaster in case of bottle with curvy bottom in case of flat bottom we suggest to remove the coaster UM_2013_40_enoliving_it 45 Rev 01 July 2013 enomatic wine serving systems 3 place the bottle on the cylinder paying attention that the coaster is matching with the bottom of the bottle itself same attention must be paid in case of bottle with flat bottom by removing the coaster 4 Once the bottle is placed on the cylinder push it downwards
16. l uso di sostanze pericolose nelle apparecchiature elettriche ed elettroniche nonch allo smaltimento dei rifiuti In respect of 2002 95 EC 2002 96 EC and 2003 108 EC about the reduction of dangerous material use contained in electric and electronic equipment and about waste disposal The symbol showing a crossed litter labelled on the device and or on the packing is to mean the need to separately dispose the equipment from normal domestic waste User must therefore forward the dead equipment to an authorized electric and electronic waste collection in order to ensure environment respectful disposal User can also forward the dead equipment to an authorized dealer and ask for substitution in case of same machinery purchase A correct disposal and treatment of expired equipment will result into reduced risks for population and increased environment respect Recycling process will be easier Illegal disposal is a crime persecuted by law All Enomatic models described in this manual are SUITABLE FOR DRY LOCATIONS ONLY SUITABLE FOR ENVIRONMENTS UP TO 32 In accordance to ISO 7000 Graphical Symbols for use on equipment UM_2013_40_enoliving_it 23 Rev 01 July 2013 enomatic wine serving systems DICHIARAZIONE CE DI CONFORMITA CE DECLARATION OF CONFORMITY DISTRIBUTORE AUTOMATICO PER VINI modello Enoline Enoliving AUTOMATIC WINE DISPENSER model Enoline Enoliving Noi Enomatic Srl Via di Meleto
17. l and quickly contact your Enomatic distributor in order to define a Supervising visit Please make sure that following items are included in the delivery 1 x system enoliving 1 x User Manual 3 x Plastic straws image 1 1 x drop rubber carpet image 2 1 x tap seals kit 2 x bottle coasters image 3 1 x eventual foodgrade Argon canister E938 image nr 4 Image 1 Image 2 Never leave the packaging contents plastic bags foamed polystyrene nails etc within the reach of children since they are a source of potential danger Please be eco friendly and recycle the packaging components UM_2013_40_enoliving_it 8 Rev 01 July 2013 enomatic wine serving systems 6 Installation For an optimum installation a technical inspection is needed where the installation will be performed in order to establish the correct positioning ensure there is an earthed electrical socket which complies with the regulations 1 ee After unpacking your Enomatic Wine Serving System place it on a solid and fire extinguisher desk or holder between 800 and 1300mm 31 51 from floor Verify the stability of the dispenser after placing it on the desk Tight the argon canister E398 see section 6 3 Connect the electrical cord to the net and turn the machine on From now on Your Enomatic wine Serving System is ready for bottles engagements Enjoy your wines Above mentioned operations mus
18. manually in the special thread placed in the higher part of the cabinet until the complete screwing before the complete screwing a gas venting will occur keep screwing see technical drawing below related to the canister insertion and replacement We suggest in case of dispenser moving due to failure or other reasons to remove the canister even if it is not empty following the sections 3 4 1 open the back panel by pressing on the upper part of the panel itself see picture above On the upper side there are two magnets pull the panel towards yourself when is partially open and remove it completely UM_2013_40_enoliving_it ae s Rev 01 July 2013 enomatic wine serving systems e 2 Check the threaded hole 1 where the gas canister will be screwed 3 Insert the canister joint in the special hole threaded and start to turn the canister itself keeping it from the lower part clockwise as showed in image above Turn the canister till the complete screwing before the complete operation a gas vent will occur keep on screwing UM_2013_40_enoliving_it 12 Rev 01 July 2013 enomatic wine serving systems 4 for the canister replacement unscrew the cylinder itself anticlockwise and remove it see image above Please consider that in case of empty canister a residual of gas could remain inside and a gas vent could occur Repeat sections 1 2 3 for the new canister placing Before t
19. ntaining diluted citric acid E330 3 4 teaspoons each 750 ml of water ca 15 20 grams of product e run some citric acid cleaning solution pours wait some minutes and repeat the supply serve approximately 300mls each time Wait a few more minutes and remove the bottle containing the cleaning solution e inserta bottle of clean water and flush the Bottle Tube and Tap with the water serve approximately 200mls e insert a bottle without internal straw and perform some supplies in order to remove completely the water from the tap e Replace the bottle with a new bottle of wine to be served UM_2013_40_enoliving_it 20 Rev 01 July 2013 enomatic wine serving systems 10 3 Extraordinary maintenance An extraordinary maintenance must be run every six months in order to ensure perfect cleaning on the ducts and to avoid wine sediments all over them Change the wine bottle with one containing chlorine based cleaner non smelling diluted in clean water in accordance with the manufacturer instructions for example 2 of chlorine in 750ml of water e supply a few serves of the chlorine based cleaning solution wait 10 minutes and repeat the supply serve approximately 100mls Wait 5 minutes and remove the bottle containing the cleaning solution e replace the bottle with a bottle containing diluted citric acid 10 grams of citric acid added to a wine bottle of clean water and serve approximately 150mls e install a bottle of
20. o ensure that they do not play with the appliance Children shall not play with the appliance Always unplug the Enomatic model from the electrical socket before carrying out extraordinary maintenance operations In case of appliance moving don t lift it up or move it with bottles engaged Check the electrical components before using the appliance in case of any damage please call Enomatic Do not use electrical appliances inside the food storage compartments unless recommended by the manufacturer For any repairs contact only Service Centres authorised by the manufacturer or supplier and insist to get only original spare parts Failure to comply with the above may harm persons damage property and will invalidate the Warranty Do not operate the Enomatic Wine Serving System outdoors UM_2013_40_enoliving_it 4 Rev 01 July 2013 enomatic wine serving systems 11 Avoid the electrical cord hanging down the supporting Surface table counter etc and from coming into contact with hot surfaces Do not place the Enomatic model on top of its electrical cord Never connect a damaged cord but ask your local distributor for a Spare part Use original spare parts only 12 Keep the Enomatic Wine Serving System far away from heat sources 13 Avoid that the electrical cord remains dangling or in contact with heat sources Avoid the appliance positioning on its own electrical cord 14 Before plugging the Enomatic model into the elect
21. ottle or to engage a new one by pressing the bottle downwards the lifter will be blocked allowing the bottle replacement for the bottle engagement see section 7 2 UM_2013_40_enoliving_it 17 Rev 01 July 2013 enomatic wine serving systems 8 1 Volumes This function is to configure the dispensing quantities will be later on poured The dispenser by default is set in free pouring with free pouring set the wine will be Supplied at the button pushing until the button itself will be released To set a specific volume see the following instructions insert the plastic straw and the bottle in the dispenser see sections 7 1 and 7 2 Switch off the dispenser with the bottle engaged main switch in position 0 OFF while the dispenser is OFF press and keep pressed a pouring button while you are keeping pressed the button switch on the dispenser main switch in position I ON the button led after a while will turn off release the button the button led will start to blink while the buttons LEDs are blinking place a glass or a graduated cylinder under the serving spout press the button again the dispenser will start to supply when the desired volume is reached release the button During the programming mode the button can be pressed several times in order to adjust the volume is suggested the use of a graduated cylinder to verify the exact volume supplied see picture aside Important the minimum
22. rical socket check that the main switch General is set to O off mode 15 Before supplying the Enomatic model check the voltage indicated on the Data Label it has to correspond to your country s standard voltage supply value You may require an adapter to plug the cable into your electrical socket 16 Do not clean with corrosive detergents or scraping tools Use only a soft and non abrasive damp cloth UM_2013_40_enoliving_it 5 Rev 01 July 2013 enomatic wine serving systems 2 Introduction This Operating Manual ts an integral part of the Enomatic Wine Serving System therefore we recommend you to keep it available for future references Before proceeding to install and operate your Enomatic Wine Serving System please read carefully the instructions contained in this Operating Manual They provide important information on safety during installation duty and maintenance The manufacturer will not be liable in any way for any damage that may be caused by unsuitable or unreasonable use and incorrect interpretation of the safety rules and installation instructions 3 Model Identification Every Enomatic model is identified with a unique serial number printed ona Data Label There is one Data Labels on the machine is placed on the rear panel The Data Label is the only means of identification authorised by the manufacturer and it contains all the data needed by the manufacturer to provide prompt and cle
23. settable volume is determined by the minimum pressing time of the button 17 Hence to set the volume is necessary to press the button for at least one second otherwise the dispenser still remains on free pouring afterwards the first push of the button for at least one second it will be possible to press the button itself to adjust the volume even for less than one second once the volume is set the LED of the button will stop the blinking saving the value in both positions the set volume will be the same for both positions While one position of the dispenser is pouring wine is not possible to pour in the other one it is necessary to wait the blinking end of the button related to the position that is ie _ pouring wine to eventually start to pour wine in the other position To return to the free pouring switch off the dispenser and then switch on again keeping pressed the pouring button stop pressing the button and wait until the blinking finishes The dispenser will return in free pouring automatically When the setting is completed the dispenser will blink in different ways due to the chosen function 1 Nr 3 blinks for programmed volume 2 Nr 1 blinks for free pouring UM_2013_40_enoliving_it 18 Rev 01 July 2013 9 Troubleshooting enomatic wine serving systems This guide is to provide a quick support in case of faulty behaviors There is a leak of gas
24. t be run after User manual reading UM_2013_40_enoliving_it 9 Rev 01 July 2013 i jak 6 2 COSE enomatic wine serving systems Parts of the Enomatic Wine Serving System Nr 2 pouring buttons Nr 2 pouring spout Nr 2 transfers for pneumatic pistons Nr 1 drop rubber carpet Nr 2 lateral panels in Baydur Stainless steel parts Panel for canister housing Main switch Electrical cord outlet Electrical supply The enoliving lite operates at from 100 to 240V 50 60HZ depending upon the country Exception for the dispenser dedicated to the USA and Canada markets it can be powered only to 115V see technical characteristics on section 11 Before connecting these models to the electrical sockets check the voltage detailed on the Data Label on the back panel The enoliving has one 1 switch located on the back For the switch O is OFF and or is ON The Enomatic models must be connected to a supply system equipped with an effective earth connection in accordance with the rules and provisions prescribed by law UM_2013_40_enoliving_it 10 Rev 01 July 2013 enomatic wine serving systems 6 3 Gas connection Enoliving needs foodgrade Argon E938 Canister housing is placed in the rear part of the dispenser see picture below Ascertain that the main switch would be positioned on 0 OFF and disconnect the electrical cord from the socket Argon canister E938 has to be screwed
25. th after the original date of delivery of the Goods was requested The Warranty only applies to the original Purchaser of the Goods and is not transferable All Warranty service will be provided by the Company during normal working hours Replaced parts become the property of the Company and repairs or replacements do not extend the Warranty period Any transportation costs including return shipment associated with a Warranty claim will be the responsibility of the Purchaser THE WARRANTY DOES NOT COVER any defect failure or damage arising from a failure to follow normal operating procedures and instructions or failure to ensure proper care use and regular maintenance as outlined in the documentation provided by the Company b incorrect transportation installation removal or handling c the effects of fair wear and tear rusting or damage to varnish enamel or paintwork d periodic general cleaning and any labour or part charges incurred as a result of service in the nature of maintenance and support including the replacement of consumable parts house fuses or resetting of circuit breakers e incorrect storage or exposure to unusual or excessive environmental chemical atmospheric mechanical electrical including defective house wiring or by operating the Goods on incorrect voltage or cycles or fluctuations or interruptions in the power supply or thermal stress during the course of installation or use f any drawing design or sp
Download Pdf Manuals
Related Search