MOD. UBF 28 NEW - Fiorentini SpA
Contents
1. 4 7 3 Side Brush Replacement 4 4 7 4 Waste Tank Emptying manual version essere 4 7 5 Waste Tank Emptying automatic 4 7 6 Suction Engine 0 0 20 0 4 4 4 4 7 7 Filter Shaker Engine 2 2 4 7 8 Petrol engine maintenance endothermic motor 4 7 9 Controls for endothermic motor 2 2 MAINTENANCE 5 1 Maintenance TEE 5 2 Batteries Maintenance RIRs nennen nsn nnn Ui aca edle san co D22 Water cadeva 2 2 9 Cae limi 5 2 4 Off duty or inactive batteries 2 92 5 Ballenes disposali ice 5 3 Petrol engine maintenance endothermic motor 5 9 1 Electric System Gonirol lina 54 Testedo be carred Utah illo delia 5 5 Maintenance SERVICE Register CET 6 1 Adresses for technical assistance 6 2 Claim Report 21 21 23 23 24 25 25 26 27 27 28 29 30 30 31 31 31 31 31 32 32 32 33 34 35 FEATURES2. STARTING AND USE INSTRUCTIONS UBF 28 NEW 4 STARTING AND USE INSTRUCTIONS 4 1 TRANSPORT AND HANDLING The machine is delivered to the purchaser in a proper package see picture 4 1 below A black arrow on the package indicates the barycentre This arrow must be in the middle of the elevator or transpallet forks The package must be carefully handled Do not place one package on another one If agreed with the purchaser the machine can be delivered without package placed on a pallet and fixed by means of straps The purchaser must make sure that the machine has not been damaged during the transport and that all papers on the machine Otherwise the purchaser must 7 immediately contact FIORENTINI order to sort out the problem The purchaser is responsible for the transport of the machine if not differently agreed with FIORENTINI face PICTURE 4 1 The machine must be handled with proper devices as stated in the scheme below Make always sure that the black arrow on the package is in the middle of the elevator forks or the straps Anchorage and or strapping points are set up in order to keep the machine on balance during the transport PACKAGE HANDLING EQUIPMENT Carton box or plywood box on a Fork elevator pallet Bands used for lifting the machine up must have the same loading capacity as the machine load Handling operations must be done without causing a loss of stability of the machine Otherwise t
3. EN 12100 1 EN 12100 2 Norme applicate Harmonized Standard Applied Angewandte harmonisierte Normen Normes Harmonis es Appliqu es Ing O Fiorentini S r l Il titolare chairmen g rant Piancaldoli Ing O Fiorentini Luogo e data Firma ii Eo E In caso di modifiche apportate alla macchina questa dichiarazione non e piu MAL FEATURES AND TECHNICAL DATA OF THE MACHINE UBF 28 NEW 2 FEATURES AND TECHNICAL DATA OF THE MACHINE 2 1 IDENTIFYING THE MACHINE A silver label is stuck on the metal sheet under the seat and clearly shows the data referring to the CE brand Ing O Fiorentini S r l MADE 50030 Piancaldoli FI IN CE FIGURA N 2 1 The label has never to be removed and should always be kept readable In case of 7 damage t is necessary to ask for a duplicate The sweeper machine cannot be sold without the label 2 2 DESCRIPTION AND PARTS OF THE MACHINE The machine UBF 28 NEW is designed for the treatment of flat surfaces through the process of brushing and the following process of collection of dirt in a sharps container The system of power is supplied by a series of accumulators batteries battery version or a gasoli motor endothermic motor version which feed all the motors and the electric control By means of a rotating brush set in front of the machine the dust is put in the middle of the machine The main brush takes it into the waste tank T
4. ING SpA INDUSTRIAL CLEAN NGMACH NES SWEEPER Mon UBF 28 NEW USER AND MAINTENANCE MANUAL Rev 00 Congratulations for your choice FIORENTINI S p A thanking you for the preference to our product would like to remind you that FIORENTINI s S p A production covers manufacture and marketing of industrial cleaning machines and is currently a leading company in this sector Our tradition and competence guarantee technical quality of your choice actually all our products are being built first quality materials through criteria that can give reliability solidity and functionality satisfying every kind of customers FIORENTINI has recently obtained the quality system certificate conforming to the requirements of UNI EN ISO 9001 2000 We wish therefore inviting you to contact us unhesitatingly for every kind of request as technical or commercial we ll be pleased to be at your disposal for any information you may need INDEX 1 GENERAL INFORMATION pag Tels esce aoe VERE Cl ss TT 1 95 Mania Bair WN CIA AIM ACI oO R5 A 2 FEATURES AND TECHNICAL DATA OF THE MACHINE 21 dening TNC Machine m T 00 2 2 De
5. Directives on product safety Therefore we suggest to all authorized operators to read carefully this manual contacting FIORENTINI S p A for any explanation The manual has to be used every time the operator forgets a procedure or when new operators have to be trained For publishing reasons pictures and drawings can look different from the reality but without arising doubts Special symbols and bold type and or sloping get the attention of the reader on remarkable information in particular for safety The revision index is written on the left at the bottom of every page The list of those pages that have been updated has to be found at the end of the manual 1 4 WARRANTY Warranty conditions are stated as below when not differently specified in the order confirmation WARRANTY OBJECT The machine has been designed and built for a long lasting use without relevant problems Anyway if problems arise during the warranty period FIORENTINI S p A is engaged to repair or substitute for free those parts that are broken or damaged by defective materials working defects or imperfect assembly FEATURES AND TECHNICAL DATA OF THE MACHINE UBF 28 NEW Warranty is not given for parts whose early breaking or wear and tear are due to Non respect of instructions included in this manual Breaking and or changes made up without FIORENTINI s approval Not use of genuine spare parts Interventions made up by unauthorized personnel
6. 353314 Via Ponte Corvo 20 Tel 0774 357184 353015 STABILIMENTO 50030 PIANCALDOLI FI Fax 055 817144 Loc Rombola Tel 055 8173610
7. A Fax 0774 353419 353314 Via Ponte Corvo 20 Tel 0774 357184 353015 STABILIMENTO 50030 PIANCALDOLI FI Fax 055 817144 Loc Rombola Tel 055 8173610 Most of the technical problems can be sorted out with short intervention This is why FIORENTINI S p A suggest to read carefully this manual before using the machine On the contrary if the customer needs a FIORENTINI S technician please inform us about the problem in order to sort it out with the right material 6 2 CLAIM REPORT Please fill in the format below if the machine shows particular problems Rev 00 18 02 09 Pag 34 36 TECHNICAL ASSISTANCE UBF 28 NEW Company Operator s name Role Date Signature Machine MINISWEEPER Type Purchase date S N Warranty ves L wo Work hours Where does the machine normally work Code of the defected Description component Fault Fault short description Mechanical component Wrong functioning Electric system Engine Missing component Estremely noisy Water leak Other Customer s suggestion 00 18 02 09 Pag 35 36 Mat n Serial no Nr de serie Data di spedizione Date of shipment Date de spedition Distributed by ING O FIORENTINI S p A THE BEST IN FLOOR MACHINES FILIALI 20132 MILANO Fax 02 2592779 Via Palmanova 211 a Tel 02 27207783 2564810 00012 Guidonia Montecelio ROMA Fax 0774 353419
8. AND TECHNICAL DATA OF THE MACHINE UBF 28 NEW 1 GENERAL INFORMATION 1 1 SYMBOLS This symbol is used to get the operator s attention on procedures or precautions to be followed in order to avoid damages to users or to the support This symbol is used to get the operator s attention on general information 1 2 WARNING FIORENTINI S p A is the only owner of this manual The reproduction of all or part of the manual or the transmission to third parties with mechanic or electronic devices are forbidden without a written manufacturer s authorization This manual is supplied to the customers in one original copy when differently specified in the order This manual is supplied to the customer with the machine and it must be kept with it even when the machine has to be transferred Please keep the manual in a safe place and for all the machine lifetime In case of loss ask for a duplicate to FIORENTINI S r l FIORENTINI S r l is not responsible for any kind of damages caused by people or things due to the non observance of the instructions dealt in this manual FIORENTINI reserves the right to add at any time and without notice all the technical and commercial changes considered useful for the customer Therefore data and information in this manual can be updated 1 3 MANUAL CONSULTING This manual deals exhaustively with all arguments that are necessary for an easy and safe use of the machine as it is recommended by European
9. ARGE STARTING AND USE INSTRUCTIONS UBF 28 NEW 4 7 FUNCTIONING Switch the sweeper on and start both the side brush and the central brush by means of the levers Then start the suction engine which intake and collect the rubbish into the recovery tank The brushes start working by means of the accelerator lever Drive the machine with a regular speed during the sweeping process Do always keep the suction engine clean from dust As a consequence the filter is always clean and can work properly Before any operation make sure that all protections well fixed 4 7 1 LEVERS AND PEDALS FUNCTIONING This machine is equipped with following levers gt accelerator lever picture 4 7 detail 1 select forward gear by means of the lever on the operator s right hand Select reverse speed by means of the lever on the operator s left hand 5 The accelerator lever start all the mobile parts of the UBF28 NEW Therefore brushes work 7 only after having started the lever side brush lever picture 4 7 detail 2 push the lever down and the side brush goes down onto the floor flap lifting pedal picture 4 7 detail 3 central brush lever picture 4 7 detail 4 push the lever down and the central brush goes down onto the floor pull the lever to put the brush in its original position Endothermic motor version parking brake detail 5 With this pedal it is possible to slow down the machine till complete stop This pedal works a
10. C MOTOR The endothermic motor requires few and simple operations to allow a long and perfect function Apart from this manual the customer receives also together with the machine the maintenance manual of the motor given by the manufacturer company For any kind of inconvenience it is therefore recommended to refer to the endothermic motor manual Here following are some necessary operations to be done on the motor gt VV Vv v to fill the machine with fuel it is necessary to unscrew the plug detail 1 picture 4 15 and fill the proper tank the oil tank detail 2 contains the lubricant necessary for the motor functioning Unscrew the plug to refill the lubricant oil the air filter is protected by cover detail 3 Unscrew the fixing wheel to reach the filter detail 4 when it is necessary replace the sparking plug detail 5 the battery detail 6 is required to start the machine 3 4 IMAGE N 4 15 STARTING AND USE INSTRUCTIONS UBF 28 NEW 4 7 9 CONTROLS FOR THE MACHINE WITH ENDOTHERMIC MOTOR On the machine with endothermic motor it is important to know two simple operations that grant a better efficiency of the motor Before starting the motor pull the STARTER lever detail 1 image 4 16 Once the motor is switched on push the lever to its original position Next to the STARTER lever there is the accelerator lever detail2 The machine speed can be varied using this control For the other contr
11. F 28S NEW UBF 28B NEW MAIN SPECIFICATIONS SWEEPING WIDTH e WITH 1 SIDE BRUSH e WITH 2 SIDE BRUSHES 4200 4200 m h 3500 m h FLTERING SURFACE em om GENERAL specications o FRONT FRONT FRONT MOTOR WHEEL HYDROSTATIC HYDROSTATIC W ELECTRO BRAKE 10 10 75 dB 75 dB ELECTRIC SYSTEM 6V 320A h MOTORS OO O S MOTOR BRAND LOMBARDINI HONDA 4 Da coume AR AIR 1 _ DIMENSIONSANDWEIGHT _ i390mm 1390mm i390mm WEIGHT empiy machine _ 338kg 338k9 270k9 enon ELECTRO ELECTRO DUVPNGHEGTH 1320 mm isiomm measures mA oron SS ___ ooo 24V 180W 3000 RPM 24V 650W 1800RPM 33A 24V 100W 90RPM 5A The above mentioned characteristics not binding for the manufacturer they be changed without any notice ING O FIORENTINI Co is always at disposal for any information par 6 1 FEATURES AND TECHNICAL DATA THE MACHINE UBF 28 NEW MEASUREMENT UNITS CONVERSION 1 bar 100 kPa 14 5 psi Length 1 inch 1 25 4 mm Power 1 kW 1 36 CV 1 34 BHP Temper 710 110 SAFETY UFB 28 NEW 3 SAFETY 3 1 RIGHT USE OF THE MACHINE This sweeper has been designed for an industrial use It can sweep on flat surface or with 10 slope 3 2 WRONG USE
12. Missing maintenance Natural calamities WARRANTY CONDITIONS Warranty is granted for 24 months since the delivery date of the machine This is a single warranty term and it cannot be extended RETURNED GOODS Intervention demands must be sent to FIORENTINI Service Dpt only after a careful analysis of the problem and its causes Following information have to be given to FIORENTINI s agent e Serial number you get it from the silver label sticked on the machine 2 1 e Code and position of the component taken from the spare parts list e A detailed description of the problem and its causes The components considered under warranty are delivered ex factory Those ones being substituted belong to FIORENTINI Co Please send defected electric or electronic material separately in order to divide and recycle material with dangerous substances see directive about RAEE 2002 96 1 5 Expandable materials like brushes squeegee blades and materials whose lifetime cannot be predetermined are not under warranty More FEATURES AND TECHNICAL DATA OF THE MACHINE UBF 28 NEW APPLICATION MODALITY Defective components must be sent back to FIORENTINI S p A in order to establish the anomalies causes and apply therefore the warranty Repair and replacement under warranty will be done in FIORENTINI workshop by third parties or in loco In case of repair
13. OF THE MACHINE the sweeper cannot be driven by non authorized personnel this machine cannot work on surfaces with holes this machine cannot sweep on sloping surfaces The machine cannot sweep sloping surfaces whose gradient is higher than 8 The machine cannot be used in places with dangerous substances and in particular with explosive atmospheres or with a bad microclimate The machine cannot clean surfaces with inflammable products The machine cannot be used as a means of transport for people or other means of transport The protection devices of the machine cannot be modified or tampered Batteries must be recharged in a fanned room The operator have always to respect safety rules The operator cannot use equipments or devices that can create problems to the machine working The machine components cannot be modified without FIORENTINI s authorization The operator cannot use acids that can damage the machine gt The operator has always to respect the rules written in the user manual VV NON ON VV Y V NON Y Y Please read carefully and do not cover the labels sticked on the machine FIORENTINI S r l is not responsible for a wrong use of the machine 3 3 SUGGESTED EQUIPMENT In order to use the machine in a proper way we suggest to use the FIORENTINI s equipment and original spare parts FIORENTINI S r l Technical Dept is always at your disposal to design components or parts for a particular use o
14. anual must be carried out by FIORENTINIs technicians Interventions on the electric system must be carried out by a trained technician 5 4 TESTS TO BE CARRIED OUT FREQUENCY o CONTROLS Safety device 1 12yeas Professionaltechnician Eletricsystem 1 2years FIORENTINI technician Brakesystem _ 1 3years Professional technician Complete revision 5 FIORENTINI technician MAINTENANCE 470 Cleandusttank Daily 7 Operator Vacuumfiter Daily 7 Operatr Cleaning of vacuum hoses 1 Weekely Operator Check the water level on sele Professional technician are well fixed Check the motors carbon E a year Professional technician lumen iiid Check the motor oil level EE _ Replace the motor oil filter 3months Replace the motoroil Every month Operator Rev 00 27 04 09 Pag 32 36 MAINTENANCE UBF 28 NEW 5 5 MAINTENANCE REGISTER DATE OPERATOR INTERVENTION NOTES SIGNATURE Rev 00 27 04 09 Pag 33 36 TECHNICAL ASSISTANCE UBF 28 NEW 6 SERVICE 6 1 ADDRESSES FOR TECHNICAL ASSISTANCE Do not hesitate to contact FIORENTINI S p A service for any kind of information or request ING O FIORENTINI S p A THE BEST IN FLOOR MACHINES FILIALI 20132 MILANO Fax 02 2592779 Via Palmanova 211 a Tel 02 27207783 2564810 00012 Guidonia Montecelio ROM
15. f machine as requested by the customer SAFETY UFB 28 NEW 3 4 OPERATORS QUALIFY The below specs shows the qualify requested from the operators depending on the kind of maintenance to be done on the machine OPERATION OPERATORS QUALIFY Installation disinstallation Fiorentini technician Mechanical parts maintenance Fiorentini technician 4 FIORENTINI S r l suggests to train the operator before using the machine The operator also must be trained about safety rules and carefully read this manual the non observance of the instructions dealt within this manual FIORENTINI S r l is not responsible for any possible damage to people and or things caused by 3 5 PROTECTION AND WARNING DEVICES the machine is working e It is absolutely forbidden to tamper or disconnect safety and warning devices while e Itis important to check periodically safety and warning devices Fiorentini UBF 28 NEW is equipped with a central nylon brush which rotates Central brush when the machine is working The central brush is protected on both sides by a stainless steel panel and two cases which avoid the contact with dangerous protection components These protection devices can be only willingly removed from the machine STARTING AND USE INSTRUCTIONS UBF 28 NEW 3 6 SAFETY DEVICES The machine is equipped with the following safety devices gt Socket battery version picture 3 1 the same socket used
16. f the UBF28 NEW This is why the operator must regularly check the efficiency of the engine see 5 4 Please follow the following instructions in order to reach the suction engine gt gt gt gt gt remove the key from the dashboard in order to avoid that the machine starts lift the protection cover under the seat picture 4 13 detail 1 to reach the suction engine disconnect the plug picture 4 13 detail 2 and remove the suction engine detail 3 make the necessary maintenance follow the opposite steps in order to take the machine at the original status PICTURE N 4 13 4 7 7 MAINTENANCE OF FILTER SHAKER ENGINE The filter snaker engine remove dust from the filter in order to keep it always efficient By means of the button on the dashboard the operator starts the filter shaker engine see 4 6 1 Please follow the below instructions for basic maintenance of the filter shaker engine VVVVV remove the key from the dashboard in order to avoid that the machine starts lift the protection cover under the seat picture 4 14 detail 1 remove the protection panel detail 2 remove the two knobs detail 3 and pull the engine out detail 4 the operator can now reach the filters and make the due maintenance detail 5 follow the opposite steps in order to take the machine at the original status STARTING AND USE INSTRUCTIONS UBF 28 NEW 4 7 8 PETROL ENGINE MAINTENANCE MACHINE WITH ENDOTHERMI
17. for the battery charger In case of emergency this socket must be taken away from the plug by means of its handle The operator must be trained about safety rules Do never restore this safety system before the problem has been sorted out If it is necessary ask for the technician help PICTURE 3 1 gt Micro under seat picture 3 1 under the operator seat there is a micro that prevent the machine from working if the operator is not seat onboard In the same way if the operator lifts up without switching off the motor the machines stops automatically To start the machine again set the ignition key to off seat on the machine then switch it on again 3 7 OTHER DANGERS FIORENTINI S r l analyzes starting from the design of the machine all the dangers that can occur while the machine is operating in order to prevent or at least low the operator s accidents Thanks to a series of signals on the machine the operator can avoid many risks that can occur SQUASHING DANGER This kind of ranger can occur e during the brushes regulation e during the batteries endothermic motor maintenance Whilst regulating the side brushes the central brush and the central washing brushes the ignition key must be kept away from the dashboard in order to avoid the casual starting of the machine Whilst the batteries recharge the operator must pay attention that any parts of his her body enter the batteries room Special labels stuck on the br
18. he machine can be damaged or the operator can de in danger Morgan STARTING AND USE INSTRUCTIONS UBF 28 NEW FIORENTINI suggest to use authorized personnel see 6 2 3 to handle the machine LOADING SYSTEM SI PICTURE N 4 2 4 2 STORAGE The machine must be stored in a closed and dry place if not immediately installed in order to keep every part safe Relative humidity must be lower than 80 and the storage temperature must be between 3 C lt t 45 C 4 3 HOW TO UNPACK THE MACHINE Cut the straps paying attention to the back spring Remove clips that join pallet and carton in case of plywood box please remove clips from both sides and basis of each panel Cut the strips that hold the machine Lay the machine on the floor VVVVV 4 4 HANDLING THE UNPACKED MACHINE 4 4 1 Battery version machine gt Check the machine and install the batteries if not already installed gt Fora brief transport of the machine please disconnect the batteries cables and remove brushes for a longer transport please use the original package of the machine STARTING AND USE INSTRUCTIONS UBF 28 NEW 4 4 2 Endothermic motor version gt Check the machine and especially the motor paying attention to the level of oil and cooling liquid gt Fill the machine with fuel gt Fora short transport of the machine empty the fuel tank and remove the brushes For a longer transport please use the original pac
19. his machine must be used on dry or at least humid surfaces By means of the dashboard the operator can control the functioning of the machine through a signalling system made of LEDs The dashboard is equipped with a battery charger indicator too Functions of the machine which can be operated from the dashboard switch on off the machine Activate the side brush Activate the filter shaker Activate the central roller brush Activate the vacuum motor VNN NN FEATURES AND TECHNICAL DATA OF THE MACHINE UBF 28 NEW The machine frame is made of zinc plated or stainless steel in order to avoid oxidation which could compromise the reliability of the machine Following are the main components of the machine zinc plated or stainless steel frame right side brush left side brush optional main brush suction and collecting system driving wheel two idle wheels seat Discharge system manual or automatic VV VV ON ON ON V WV FIORENTINI Co taking the new CE safety rules under consideration manufactures the machine following the CE directives about safety and health The materials high quality the high technology and FIORENTINI s experience guarantee the performance and the reliability of this machine Each machine is tested during the manufacturing process and the final check is done before the machine is shipped out FEATURES AND TECHNICAL DATA OF THE MACHINE UBF 28 NEW 2 3 TECHNICAL DATA UBF 28D NEW UB
20. kage of the machine 4 5 INSTALLATION Installation must be carried out by authorized personnel after reading this manual 4 5 1 BATTERIES INSTALLATION BATTERY VERSION MACHINE Please follow the instructions below to install the batteries the batteries room is under the operator s seat protected by a cover lift the cover of the batteries room up picture no 4 4 detail 1 install the batteries in their room picture 4 4 detail 2 and make sure the batteries boxes are not broken do never add distilled water after batteries recharge clean the surfaces for the cables connections use the handles on the batteries to move them YYY NN WV PICTURE N 4 4 STARTING AND USE INSTRUCTIONS UBF 28 NEW 4 6 CONTROL DEVICES 4 6 1 DASHBOARD The dashboard is made of a series of switches that activate or disactivate all the machine functions The function of each switch is shown by a picture Picture 4 6 shows the dashboard of the machine and the switches function is explained in the scheme in the following page 7 8 9 3 1 4 5 6 2 PICTURE N 4 6 SIDE BRUSH ACTIVATION BATTERY CHARGE INDICATOR BATTERY VERSION MOTOR PROTECTOR KEY SWITCH BATTERY VERSION STARTING AND USE INSTRUCTIONS UBF 28 NEW KEY SWITCH ENDOTHERMIC MOTOR VERSION VACUUM ACTIVATION OF DUST COLLECTOR AND FILTER SHAKER CENTRAL BRUSH ACTIVATION LIFT UP DOWN OF DUST COLLECTOR VERSION WITH AUTOMATIC DISCH
21. lowing instructions in order to empty the recovery tank remove the key from the dashboard in order to avoid that the machine starts remove the hook that holds the recovery tank to the machine picture 4 11 detail 1 remove the recovery tank and empty it the operator can easily move the recovery tank thanks to the wheels picture 4 11 detail 2 follow now the opposite instructions in order to put the recovery tank in its original position VVVVV PICTURE N 4 11 STARTING AND USE INSTRUCTIONS UBF 28 NEW 4 7 5 RECOVERY TANK EMPTYING AUTOMATIC VERSION Please follow the following instructions in order to empty the recovery tank gt turn the key on the control board and switch the motor on if the machine is a version with endothermic motor Press the proper key on the control board in order to lift up the recovery tank see par 4 6 1 to check the right key to use Once reached the required dumping height particular 1 pict 4 12 release the key Move the machine to reach the right position above the discharging area particular 2 pict 4 12 When the machine is in the right position pull the handle to discharge the rubbish particolar 3 picture 4 12 Follow the opposite instructions to bring the machine at the original status Vv VV WV fiorefytini D PICTURE N 4 12 STARTING AND USE INSTRUCTIONS UBF 28 NEW 4 7 6 SUCTION ENGINE MAINTENANCE The suction engine is an important component o
22. lso as parking emergency brake In the battery version machine the electrobrake works on the front wheel stopping the machine when the forward pedal is released Y VV WV PICTURE N 4 7 STARTING AND USE INSTRUCTIONS UBF 28 NEW 4 7 2 MAIN BRUSH REPLACEMENT Please follow the following instructions in order to replace the main brush gt gt gt gt gt remove the key from the dashboard in order to avoid the machine to start remove the metal protection on the machine side picture 4 8 detail 1 after having removed all fixing screws picture 4 8 detail 2 remove the brush support by rotating it clockwise replace the brush and make sure that the new brush holders are fixed in the correct way picture 4 9 re install the brush support and metal protection following the inverse instructions lly v z7 PICTURE N 4 8 PICTURE N 4 9 4 7 3 SIDE BRUSH REPLACEMENT STARTING AND USE INSTRUCTIONS UBF 28 NEW Please follow the following instructions in order to replace the side brush remove the key from the dashboard in order to avoid that the machine starts stop the side brush as described in 4 7 1 remove all the screws that fix the side brush picture 4 10 detail 1 replace the side brush do follow now the opposite instructions in order to complete the side brush replacement VVVV V PICTURE N 4 10 4 7 4 RECOVERY TANK EMPTYING MANUAL VERSION Please follow the fol
23. ment que la machine erkl rt unter ausschlieBlich eigener Verantwortung die Maschine declara bajo su propia exclusive responsabilidad que la maquina FIORENTINI Modello model modele modell modelo Matricola serial number numero matricule serienummer numero matricula Anno year annee jahr ano 2010 Fabbricata nel rispetto delle direttive e decreti and moreover is built according to the directives and decrees et est fabriqu es i en outr conform ment aux directives et ou d crets und da sie unter Einhaltung folgender Verordnungen und oder Dekrete hergestellt worden sind y que adem s ha sido fabricada en conformidadcon las directivas decretos 2006 42 CE EC EG Direttiva macchina Machines Directive Maschinen Richtlinie Directive machines 2004 108 CE EC EG Compatibilit elettromagnetica Electro Magnetic Compatibility Elektromagnetische Vertraglichkeit Compatibilit lectromagn tique 2002 95 CE EC EG Restrizione sostanze pericolose Restrictions of Dangerous Substances Beschr nkung der gef hrlichen Mitteln Restriction des substances dangereuses 2003 10 CE EC EG Protezione da rumore Exposure of Workers to Noise Gef hrdung der Arbeitnehmer durch Ger usch Exposition des travailleurs aux Bruits E conforme alle seguenti norme conform to the following laws est conforme aux norms mit den folgenden Normen bereinstimmen esta conforme a lassiguientes normas
24. ols see paragraphs 4 6 1 e 4 7 1 IMAGE N 4 16 MAINTENANCE UBF 28 NEW 5 MAINTENANCE 5 1 MAINTENANCE PROGRAM A periodical maintenance is very important Please write down in the format you find below all the interventions done on the machine parts by means of suitable tools and equipments e Make reference to FIORENTINI S r l only for service and spare parts e Trained personnel only can service the machine and especially electric and electromechanical OPERATIO INTERVENTIO HOW OFTEN Clean the recovery tank Daily Cleaning Do not use corrosive substances gt Check the suction pipes Weekly gt Check the rubber suction blades of central brush room 15 days gt Check the battery water level gt Check the suction engine Check up gt Check and register the breaking system gt Check the connection of the battery cables gt Check the brushes of each motor Every year gt Check the safety devices gt Check the electric system 5 2 BATTERIES MAINTENANCE BATTERY VERSION MACHINE The operator has to check the batteries charge when the machine is on duty by means of the indicator on the dashboard which shows gt Green light charged battery gt Yellow light slightly charged battery gt Red light uncharged battery The operator must keep the battery room open during the batteries recharge Moreover It is forbidden to use flames and or to smoke near the bat
25. once a month with a final stream intensity until gas is spread and the batteries voltage and weight are constant for 3 4 hours This operation has to be done even if the absolute weight is high gt Keep the batteries in a dry room 5 2 5 BATTERIES DISPOSAL Old batteries are toxic wastes and they have to be thrown in a suitable and authorized place for the batteries disposal For a short storage old batteries must be located in an authorized room Moreover they must be stored in sealed plastic tanks whose capacity is not lower than the electrolyte Rev 00 27 04 09 Pag 31 36 MAINTENANCE UBF 28 NEW 5 3 PETROL ENGINE MAINTENANCE MACHINE WITH ENDOTHERMIC MOTOR The motor is supplied with its own user manual which must used every time that maintenance is needed It is recommended to respect the following periods from one operation and the other Check the moior oil level every 50 hours working and replace every 150 hours Replace the air filter every 100 hours working Replace the motor oil filter every 300 hours working Check the tension of alternator belt every 250 hours working Settino and cleaning of injectors every 1000 hours working Register the cocker lever slack every 1000 hours working 5 3 1 ELECTRIC EQUIPMENT CONTROL It is very important to check the electric system up every two years Disconnected cables or burnt cables must be immediately replaced Every kind of intervention not explained in the operator m
26. or replacement in loco energy sources and the use of particular equipment have to be paid by the customer himself INTERVENTION DEMANDS Intervention demands must be sent to FIORENTINI Service Dpt only after a careful analysis of the problem and its causes Following information have to be given to FIORENTINI s agent Machine model see the silver label stuck on the machine 2 1 Serial number you get it from the silver label stuck on the machine 2 1 A detailed description of the problem and its causes Controls or regulations effectuated Code and position of the component taken from the spare parts list The components considered under warranty are delivered ex factory Those ones being substituted belong to FIORENTINI Co The warranty of the machine is no more available in case of the loss of the silver label 1 5 CONFORMITY DECLARATION conformity declaration is released with the machine and the user manual FEATURES AND TECHNICAL DATA OF THE MACHINE UBF 28 NEW DICHIARAZIONE DECLARATION DECLARATION ERKLARUNG DECLARACION DICHIARAZIONE CE DI CONFORMITA DECLARATION OF CONFORMITE DECLARATION DE CONFORMITE UBEREINSTIMMUNGSERKLARUNG DECLARACION DE CONFORMIDAD ING O FIORENTINI s r l Loc Rombola 50030 PIANCALDOLI FI ITALIA Dichiara sotto la propria esclusiva responsabilit che la macchina Declares under its own responsability that the machine Declares sous sa responsabilit exclusive
27. scription and Parts of the Machine iii 8 2 3 10 3 SAFETY 9 Ront 12 3 2 Wrong Use of the Machine aaa 12 9 9 suggested 12 824 Operator Quali IT 13 3 5 Protection and Warning 13 8 62 DEVICES te nade 14 SN AME SUBIECTO TT STILE 14 ERE 15 4 STARTING AND USE INSTRUCTIONS 421 A amen Sido aT Ode 18 42 9 516 19 4 3 Unpacking the Machine ob ot 19 4 4 Handling the Unpacked 2 19 AAA Battery 9 4 4 2 Endothermic motor nennen nnns 20 NEUE 20 4 5 dT Battery INsialiglio nali bian 46 COO DEVICSS i a ea AO We ASM OAC RS RR A Te TAG OWING serer E TRES 271 bevers and Pedale alessia 4 7 2 Main Br shdeplacemoelibos avt nt CEN Rum 20
28. tections STARTING AND USE INSTRUCTIONS UBF 28 NEW The purchaser must replace danger signals on the machine if they are damaged It is absolutely forbidden to remove or temper danger signals Battery version What is it Explosion danger it may occur while recharging the batteries because of hydrogen spread During the batteries recharge please place the machine under a What to do suction chimney or in a ventilated area and keep it away from heat and corrosive substances TTL What Is It Risk of crashing due to overturning of the recovery tank What to do Whilst recharging the batteries please make sure that any parts of your body got in contact with the batteries room STARTING AND USE INSTRUCTIONS UBF 28 NEW The purchaser must replace danger signals on the machine if they are damaged It is absolutely forbidden to remove or temper danger signals Endothermic motor version What is it This signal indicates the prohibition of removing protections of hot parts when the machine is working What to do Make sure that the machine is switched off and the key has been disconnected from several minutes A PERICOLO Di USTIONE What is it This signal indicates the danger of crashing due to closing of motor cover or to the cooling fan when working What to do During maintenance or controls please make sure that the key is disconnected
29. teries Pay attention to the battery acid Do not develop sparks near the batteries Pay attention to the batteries gazes which can burst Do not invert battery polarities VNN NN Rev 00 27 04 09 30 36 MAINTENANCE UBF 28 NEW 5 2 1 _HYDROMETRY In order to check the batteries hydrometry the operator has to follow the instructions below gt Bymeansofa hydrometre draw a small quantity of electrolyte so that the floater reaches the surface gt Make sure that the floater inside the hydrometre is not blocked gt For a new measurement after having filled the batteries with distilled water the operator has to wait until the liquid inside each battery becomes homogeneous 5 2 2 WATER FILLING UP gt Fill distilled water up in each battery cell before the recharge The liquid inside the batteries has to be of 6 mm over the plates gt operator has to repeat the same operation every time the level decreases every week 5 2 3 CHARGE LIMITS It is not necessary to recharge the batteries if the hydrometry after a work day is not under 1 24 28 B The highest suggested temperature is 45 C If the electrolyte temperature increases more than 10 12 C compared to the outside temperature the batteries can be overcharged 5 2 4 OFF DUTY INACTIVE BATTERIES Inactive batteries looses their automatically their charge If batteries do not continually work the operator has to gt Charge the batteries
30. ush cover or on the recovery tank prevent dangers to the operator see 3 7 URNOVER STARTING AND USE INSTRUCTIONS UBF 28 NEW This kind of ranger can occur during the normal operating of the machine when you exceed sloping limits as specified in the manual and you use the machine to clean disconnected surfaces or with holes and high depressions Do not use the machine to wash sloping surfaces higher than 10 or surfaces with holes or depressions which might compromise the stability of the machine FIORENTINI is not responsible for accidents occurred to people or things provoked by a wrong use of the machine i e using the machine on surfaces which can compromise its Stability The purchaser must stick proper labels on the machine to show the operator its right use 3 8 SAFETY SIGNALS Among safety signals there are Dangers signals are triangular with black DANGERS pictures on a yellow background Prohibitions signals are round with black pictures and a red stripe During the installation or the maintenance make sure that the ignition key is not in the dashboard before removing the mobile protections While the machine is operating make sure that all covers are well fixed What is it Crashing danger it can be due to parts in movement of the machine What to do During the installation or the maintenance make sure that the ignition key is not in the dashboard before removing the mobile pro
Download Pdf Manuals
Related Search