- MIGHTY SEVEN
Contents
1. User s Manual AIR SANDER Read this manual carefully before installing operating servicing or repairing fTi7 E Working environment 1 Using these tools in any potentially explosive environment is strictly prohibited 2 lt is always recommended that these types of tools must be operated when standing on a solid or firm location 3 Always use these tools in a well ventilated area 4 Slipping stumbling and falling are the major causes of potential serious injury therefore a clean and clutter free surface in the working area before operating the tools is strongly recommended Air supply and connection requirements 1 The maximum recommended air pressure during operation must not exceed 90 psi 6 3bar Higher air pressure may create unsafe operating conditions for the tool and the user 2 The compressed air should be cooled and have a water filter installed at the outlet end of the compressor Even with a water filter installed some water may still condense in the piping or hose and will enter the tool mechanism causing premature damage to the tool Therefore it is recommended to install an air filter lubricator device somewhere between the tool and the compressor 3 Always use an air compressor of the proper capacity to operate each tool 4 Clean the hose with a blast of compressed air before connecting the hose to the air tool This will prevent both moisture and dust inside the hose from entering the t2. the shroud need to be cleaned by 5 Follow all the recycling laws of waste disposal once this tool is no longer usable Accessory installing A Suitable for QB 56 series Dirt outlet Three options to be connected here 1 Supplied dirt collecting bag 2 Vacuum cleaner 3 Central dirt collecting system Air inlet connect here to air hose Pad changing 1 Insert the supplied spanner into the shroud and hold in place 2 Manually turn the pad counterclockwise to loosen it CE No NDEx No DESCRIPTION QTY A 27 B 58502P27 FRONT PLATE 1 BALANCER 5 1 QB 58502T50 STAINLESS MESH 3 PCS QB 58502P51 SHIM QB 58502P52 PIN 3 12 4 31 QB 1 4 33 9B A 334 41 2B 1 SET 4 47 9B 49 bd 1 3 4 6 8 9 0 QB 58502P41 5 PAD HOOK UP QB 58502P42 EXHAUST SLEEVE 3 6 T 9 1
3. arts Oc Alelo MELLE 1 Before connecting the air hose to this tool or after operating apply 4 or 5 drops of pneumatic oil into the air inlet and run it for several seconds referring this operation to the attached picture compressed air occasionally Regular maintenance Accessory installing B Suitable for QB 56 series Dirt collecting b Connect here to air hose Part List Item No QB 58502 No NDEx No DESCRIPTION aT e a8 s8502P03 screw mre 1 SCREW M412 E a as seso2Poa Jorne 7 x 6 o s5s502P06 BUSHING 7 x e oB 58502P08 vve SiC 4 e o ss502P09 srne r 10 a 5e502P10 PACKING Te 13 a8 s8502713 O RING 2PCS TSET 19 QB 58502T19 RUBBER BUSHING 1 SET 2 PCS A 20 oB 5e502P20 SNAPRING 7 A 21 oB 58502P21 BEARINGE000zz 1 A 22 oB 58502P22 REAR PLE 1 D 23 06 58502723 ROTOR BLADE 5 PCS 1 SET A 26 aB 58502P26 orne 2 Maintain this tool regularly by performing the same oiling application every 3 to 4 hours of operation 3 Do not lubricate tools with flammable or volatile liquids Use only the lubricant recommended by Mighty Seven or authorized dealers Any other lubricant will lead to reduce performance of the tool and permanent damage Whenever any unauthorized lubricant is used by accident flush it immediately with recommended pneumatic oil 4 To maintain the tool always in good function the components inside
4. d should meet the exact specification which is specified in the attached data table shown on the next page 14 Make sure the allowed operation speed of the self felt sanding paper or polisher which is going to be used must be higher than 15000R P M 15 Make sure that the direction of the sparks generated from the sanding paper is properly directed so it will not create a hazard 16 Always turn off the air supply and disconnect the air hose before replacing sanding paper polisher or making any adjustments on this tool 17 While replacing the self felt sanding paper make sure that it is placed concentrically on the support pad 18 Release the throttle lever to avoid danger if there is a failure of energy supply and when connecting or disconnecting the air hose 19 Make sure there is no gas or combustible material stored near the tool when servicing changing sanding paper polisher or storage 20 Prolonged use will cause user fatigue Periodic breaks are recommended for user safety 21 It is recommended to stop operating the tool whenever the user experiences discomfort tingling or pain during use 22 Beware if the compressed air hose breaks unexpectedly or is being connected or disconnected improperly This whipping action may Cause injury 23 Avoid storing this tool where it is subject to high humidity 7 Air Sander Item No QB 585072 MIGHTY SEVEN The consumable parts The replacement parts amp The non replacement p
5. od Any application or use of this tool other than what it is designed for is strictly prohibited 3 High sound levels may cause hearing damage Always wear hearing protection when operating this tool 4 Wearing eye face protection can reduce the danger of high speed materials being emitted from the tool 5 User must wear proper clothing Loose clothing long hair stings straps belts and jewelry should not be worn when operating this tool 6 Always wear gloves to reduce the risk of cuts or burns 7 Working with certain materials may create emission of dust and fumes which may cause a potential explosive environment and a hazard to the health Therefore wearing proper breathing protection and taking some preventive measures are recommended 8 Never use sanding paper which was exposed to moisture Also avoid using this tool when it is wet that will affect the function and durability of the pad 9 Do not use any grinding or cutting wheels on this tool 10 Test run the tool to confirm the rotation direction before practical use This will reduce the potential hazard due to unexpected rotating direction 11 Never operate the tool away from the work area in case the accessories may detach from the tool this may cause injury to personnel nearby 12 Use only recommended self felt sanding paper or polisher which is in good condition and is intended for use on these types of sanders 13 The diameter of the self felt sanding paper to be use
6. ool and causing possible rust or malfunction MIGHTY SEVEN EC DECLARATION OF CONFORMITY Original Language Serial Number Please refer to the tool Air Random Orbital Sander Item No QB 54502 QB 54602 QB 54702 QB 55502 QB 55602 QB 56502 QB 56602 QB 58602 QB 58502 QB 57602 QB 59602 We declare under our own responsibility that the above machinery fulfils all the relevant provisions of Machinery Directive 2006 42 EC and its amendment and is manufactured and tested according to the following standards EN 792 8 EN ISO 15744 EN 28662 1 and EN ISO 8662 8 Declared in Taichung Taiwan Dated 01 01 2010 Signature Sonne Chen Jonney Chen Declared by QA Manager Manufacturer Authorized contact to compile the technical files Mighty Seven International Co Ltd King Tony France No 70 25 Ching Qunag Rd Wu Jih Shiang 3 Rue des imprimeurs ZI R publique Nord 1 86000 POITIERS FRANCE TEL 33 5 49 30 30 90 Taichung Hsien 41466 Taiwan www mighty seven com E MAIL christian aubineau kingtony eu Overall Sound Vibration Air Hose Pressure level Item No Length Illustrator QB 58502 5 90 9 7 16 0 4 2 6 3 8 Uncertainty K 0 5a if a lt 5 m s or K 0 4a if a gt 5 m s Arne A 1 This tool should only be used as a hand operated tool It is powered by compressed air and is not insulated against electric shock 2 This tool is specifically designed for sanding or polishing a surface of metal or wo
Download Pdf Manuals
Related Search