TMO2D with lbl.004.f Software for 3 cal. Curves Operating Manual
Contents
1. You are now back at the Main Menu level MAIN MENU Select Channel Any data that you program into any of the other menus will now apply only to the channel that was selected above At this point you may either select another menu for programming or exit programming mode and return to the normal data display 2 of 10 January 2003 SEa _ SEEEaa Eo SS The Setup Menu The Setup menu includes the following submenus IMPORTANT The data entered in this menu applies only to the currently selected channel i e gas mixture Set Time unchanged see User s Manual for instructions e Set Date unchanged see User s Manual for instructions Set Backlight unchanged see User s Manual for instructions e Set Contrast unchanged see User s Manual for instructions Set Display see instructions below e Set Communications unchanged see User s Manual for instructions e Set Error Handling unchanged see User s Manual for instructions Note The Set Gas Units Scaling submenu that appears in the standard software is not present in this special software Setting the Display At the Main Menu press NO until the following screen appears Decimal Places SETUP MENU Press YES Set Display Select Decimal Place Use the arrow keys to place the 0 0 0 00 brackets around the option with the desired number of decimal places f2. see User s Manual e Select AutoCal Curve see below for instructions e Set Cal Gas Data unchanged except for identification of currently selected channel on display see User s Manual Set Settling Time unchanged see User s Manual e Set Error Handling unchanged see User s Manual e Perform AutoCal unchanged see User s Manual e Reset Drift unchanged see User s Manual e View Drift unchanged except for identification of currently selected channel on display see User s Manual In the special software the standard SetAutoCal Mode submenu is replaced with the following menu CALIBRATION MENU Select AutoCal Curve Select Calibration Curve 1ST 2nd 3rd CALIBRATION MENU Select AutoCal Curve Press YES Use the arrow keys to place the brackets around the desired channel number Press YES Press NO You may know proceed to any of the other submenus to continue programming the AutoCal parameters 8 of 10 January 2003 The System Log Menu To program the System Log menu at the Main Menu press NO until the following screen appears MAIN MENU Press YES System Log The programming of this menu is identical to the standard software and the details will not be repeated here For complete instructions see your User s Manual MAIN MENU You are now back at the main System Log menu level At this point
3. 913 274A GE Panametrics January 2003 Special TMO2D Software for Storing Three Gas Mixtures Introduction Your Model TMO2D Digital Display has been configured with a special software version LBL 004 F that permits the instrument to store calibration curves for three different gas mixtures This allows you to quickly display any one of three different gas mixtures using a single analyzer transmitter The full User s Manual for the TMO2D 910 084B will be referenced in this addendum as required IMPORTANT f your special software is version LBL 004 E or earlier do not use this document You should have User s Manual 910 084A and you should be using addendum number 913 218A instead Before proceeding be sure that your TMO2D has been installed and set up in accordance with the instructions in your User s Manual A complete set of standard menu maps may be found in Appendix B of that manual to assist in programming the unit Topics Covered Refer to the pages indicated for instructions on the following topics Note Each of the three different gas mixtures is referred to as a Channel in the TMO2D software The calibration data and channel label for each channel must be entered before accurate data displays can be obtained see next page e Programming the Channel Data page 2 e Setup page 3 e Select Channel page 2 e Outputs page 4 e Relays page 5 e Tests page 5 e Calibration page 6 e Syst
4. YES twice to enter and confirm the new value Use the arrow keys to place the brackets around DONE and press YES You are now back at the main menu level At this point you may either select another menu for programming or exit programming mode and return to the normal data display 913 274A 4 of 10 January 2003 The Relays Menu To program the Relays menu at the Main Menu press NO until the following screen appears MAIN MENU Press YES Relays As the programming of the Relays menu is identical to the standard software the details will not be repeated here The only difference is that the currently selected channel is identified in the Alarm Low Setpoint and Alarm High Setpoint prompts See your User s Manual for complete instructions MAIN MENU You are now back at the main Relays menu level At this point you may either select another menu for programming or exit programming mode and return to the normal data display The Tests Menu To program the Tests menu at the Main Menu press NO until the following screen appears MAIN MENU Press YES Tests As the programming of the Tests menu is identical to the standard software the details will not be repeated here The only difference is that the currently selected channel is identified in the Output and Gas DVM Input test display screens See your User s Manual for complete instructions MAIN MENU You are n
5. em Log page 9 e Resume page 9 e Selecting the Channel to Display page 10 January 2003 Programming the Channel Data The Select Channel Menu 913 274A In order to display accurate data for each of the three channels the correct information must be entered into the TMO2D To enter programming mode from the normal data mode proceed as follows This is the normal data mode screen with channel x displayed CHx HH MM SS X XX Alm Press NO Enter Code Press 1 2 and 3 in sequence X XX Alm with no more than a 10 second pause between keystrokes You are now in programming mode at the Main Menu level MAIN MENU Setup Only those programming steps that differ from the standard software will be described in detail in this addendum Refer to Chapter 3 Operation in your User s Manual for instructions on using the TMO2D keypad and or a connected PC for programming the unit IMPORTANT You should always be sure that the Select Channel menu in the following section has been completed before using any of the other menus The Select Channel menu must be completed before programming any of the other menus At the Main Menu press NO until the following screen appears MAIN MENU Press YES Select Channel Use the arrow keys to place the brackets around the desired channel number Press YES Select Channel to Edit 1ST 2nd 3rd
6. he generic channel labels shown in the above data screens may be replaced by labels of your choosing For instructions on doing so see page 6 913 274A 10 of 10
7. ion Data CHx of Points Y Z Point 1 CHx a aa b bb Point 1 mA c cc d dd Press YES Enter the number of available data points on the calibration curve for the selected channel Press YES twice to enter and confirm the new value Enter the gas percentage for the first data point Press YES twice to enter and confirm the new value Enter the corresponding mA output for the first data point Press YES twice to enter and confirm the new value The above two prompts repeat until the total number of data points specified have been entered Then the following screen appears Working CALIBRATION MENU Edit Calibration Data This screen appears while the calibration is being performed Press NO Proceed to the next page to enter the AutoCal parameters for the currently selected channel 7 of 10 January 2003 The AutoCAL Menu 913 274A Note See Chapter 4 of your User s Manual for a complete description of the TMO2D AutoCAL procedures and options CALIBRATION MENU Auto Cal Parameters Enable AutoCal YES no Press YES Use the arrow keys to place the brackets around the desired option and press YES After enabling AutoCal at the above prompt the following submenus become available e Set Auto Verification unchanged see User s Manual Set Time Interval unchanged
8. or the data display Press YES SETUP MENU Press NO three times Set Display SETUP MENU Press YES Done You will now find yourself back in the Main Menu at the Setup submenu Either select another menu for programming or exit programming mode and return to the normal data display 913 274A 3 of 10 January 2003 The Outouts Menu To program the Outputs menu at the Main Menu press NO until the following screen appears IMPORTANT The data entered in this menu applies only to the currently selected channel i e gas mixture Note For this example we will program Output A of Channel 1 with an output range of 4 20 mA Other outputs channels and ranges are programmed in a similar manner MAIN MENU Outputs Select output to set A B done 0 20 4 20 A Output Range mA Output A 4 mA Value CH1 x xx y yy CH1 x xx z zz Output A 20 mA Value Select output to set A B DONE MAIN MENU Outputs Press YES Use the arrow keys to place the brackets around the desired output and press YES Use the arrow keys to place the brackets around the desired output range and press YES Enter the gas that should generate a 4 mA signal for Output A in Channel 1 Press YES twice to enter and confirm the new value Enter the gas that should generate a 20 mA signal for Output A in Channel 1 Press
9. ow back at the main Tests menu level At this point you may either select another menu for programming or exit programming mode and return to the normal data display 913 274A 5 of 10 January 2003 The Calibration Menu To program the Calibration menu press NO at the Main Menu until the following screen appears Note Be sure to enter the calibration data for all three channels Refer to the Calibration Data Sheet supplied with your O2X1 for the correct calibration data MAIN MENU Calibration CALIBRATION MENU Select Channel Select Channel to Edit 1ST 2nd 3rd CALIBRATION MENU Select Channel CALIBRATION MENU Edit Channel Label Press YES Press YES Use the arrow keys to place the brackets around the desired channel number Press YES Press NO Press YES Note The label entered at the next prompt will appear at the upper left corner of the data display screen to identify the channel Channel X YYYYYYYY lt ABCDEFGHIJKLMNO gt CALIBRATION MENU Edit Channel Label Enter a channel label of up to 8 characters see your User s Manual for entry instructions When done press Press NO Proceed to the next page to enter the calibration curve data for the channel selected above 913 274A 6 of 10 January 2003 The Calibration Data Menu 913 274A CALIBRATION MENU Edit Calibrat
10. you may either select another menu for programming or exit programming mode and return to the normal data display The Resume Menu To use the Resume menu at the Main Menu press NO until the following screen appears MAIN MENU Press YES Resume Note f you wish to continue programming the TMO2D press NO at the above prompt instead CHx HH MM SS You are now back at the normal X XX Alm data mode screen with channel x displayed You have now completed the programming of the channel data for your meter 913 274A 9 of 10 January 2003 Selecting the Channel While your TMO2D is in normal data mode you can easily select any one to Display of the three programmed channels for display To do so proceed as follows IMPORTANT When you select a new channel for display the analog output and alarm relay parameters change to the currently programmed settings for the new channel CHx HH MM SS X XX Alm Select Channel 1 2 3 X XX Alm This is the normal data mode screen with channel x displayed Press YES Press 1 2 or 3 to select the channel i e gas mixture you wish to display Note Jfa valid key is not pressed within 10 seconds you are returned to the previous data mode screen without changing the displayed channel CHy HH MM SS Y YY Alm You are returned to normal data mode with the channel selected above now displayed Note T
Download Pdf Manuals
Related Search