Stand assy manual
Contents
1. ER af M4 x 6 screw LA Adapter holder Step 2 Assembling the stand 1 Mount the vertical pipes to the feet pipes two Use the feet washers flat washers 88 5 mm bore diameter spring washers M8 x 50 mm hexagonal socket screws and the included hexagonal wrench M8 to securely fasten the vertical pipes and feet pipes Insert the vertical pipe caps into the vertical pipes Insert the feet pipe caps into the feet pipes front and back gt Vertical pipe cap Vertical pipe e When mounting is finished push the stoppers of the four casters to the lock side to lock the caster If the casters are not locked the stand will be unstable during assembly and this could lead to injury Locking unlocking the caster stoppers Press the bottom of the caster stopper to lock the caster Press the top to unlock Unlock Lock A Caster stopper 2 Mount the two transverse pipes to the vertical pipes Use the two long pipes 1136 mm as the transverse pipes Use the flat washers 85 5 mm bore diameter M5 x 40 mm hexagonal socket screws and the included hexagonal wrench M5 to temporarily fasten the transverse pipes to the vertical pipes Once the four screws have been temporarily fastened fasten them all securely Flat washer 98 5 mm bore diameter Spring washer M8 x 50 mm hexagonal s2. nuts M5 seeiecctecnesseeeuncisederegeeetieene 2 e Flat washers 05 5 mm bore diameter 18 e Sheet nuts e Upper brackets left and right e Lower brackets for horizontal installation 2 e Lower brackets for vertical installation 2 e USB extension cable used when installed vertically eee i e USB connector bracket used when installed vertically eeeee 1 a M3 X 4 MIM SCIEWS ainiaan a 4 MIX 8 MIM SGTENS sisi ia 2 e M5 x 8 mm hexagonal socket screws 10 e Hexagonal wrench M8 cceeeeeeeeeeeee 1 e Hexagonal wrench M5 ceeeeeeeeeeeee 1 Cable CDS 2 esctuictedecapescemeatepeencnnertyeneteees 5 Parts included with the CR 5 e Pen tray with pen tray cover and two M4 x 6 mm screws e Adapter holder with two Velcro and two M4 SCYVOWS woceeecesssseeeseteeeees Depending on the direction of installation some of the parts may not be used Velcro is a registered trademark of Velcro Industries Horizontal installation Vertical installation Assembly for Horizontal Installation Flow of assembly and installation Step 1 Mounting parts on the copyboard 1 Mount the sheet nuts two on the right two on the left in the rail groove Attach M3 x 4 screws to the four sheet nuts Be sure they do not stick out beyond the AIS Insert the sheet nuts into
3. using two M5 x 8 hexagonal socket screws and flat washers 65 5 mm bore diameter Temporarily fasten the lower bracket for vertical installation to the screw hole in the lower sheet nut using one M5 x 8 hexagonal socket screw and flat washer 25 5 mm bore diameter 3 Mount the pen tray to the bottom of the copyboard Temporarily fasten the pen tray in place at 2 points using the included M4 x 6 screws Do not let the screws pass through the board Insert the pen tray s rail into the rail groove at the bottom of the copyboard Now lift the pen tray to catch it on the copyboard then tighten the M5 x 8 hexagonal socket screw Top control panel side D Upper SS SS Flat washers 05 5 mm bore diameter A for vertical installation Hexagonal wrench M5 Y v Lower bracket screws to fasten the pen tray in place gt Rail groove in bot tom of copyboard eg M4 x 6 screw Pen tray rail Bottom M4 x 6 screws 2 points 4 Mount the adapter holder The adapter holder is for stowing the AC power adapter Rail groove in pen tray Adapter holder Temporarily fasten the adapter holder in place at 2 points using the included M4 x 6 screws Do not let the screws pass through the board Insert the adapter holder s rail into the pen tray s rail groove
4. PLUS Z WARNING Model CR 5 T Stand Assembly Instructions 22 3602 08C stand could tip over resulting in injury Be sure to install and assemble as described in these instructions Incorrect installation or assembly could lead to injury Mounting and removal of the CR 5 unit should be performed by at least two persons Be sure to lock the stand s caster stoppers when assembling Unlock the caster stoppers when moving the stand or the Assemble on a flat surface covered with a piece of cloth etc so as not to scratch the product Fasten the various parts using the specified screws The CR 5 unit can be mounted horizontally horizontal installation or vertically vertical installation on the dedicated CR 5 stand Install in the desired direction according to the purpose Note that parts included with the CR 5 unit are also used for assembly Prepare these parts as well Parts included in the stand package e Feet With casters 2 Feet caps oo eee e Vertical frames Framo CANS enini e Feet WASMEMS oiinirioiimoeni aaee raaa 2 e M8 x 50 mm hexagonal socket screws 4 Spring WASNErS socorro eaaa 4 e Flat washers 08 5 mm bore diameter 4 e Transverse pipes for horizontal installation GABE MAM ENO inas 2 e Transverse pipes for vertical installation 687 MM in length cceeesecesessseeeessseeeees 2 e M5 x 40 mm hexagonal socket screws 10 e Cap
5. bore diameter M5 x 40 mm hexagonal socket screws and the included hexagonal wrench M5 to temporarily fasten the transverse pipes to the vertical pipes Once the four screws have been temporarily fastened fasten them all securely Flat washer N 95 5 mm bore diameter N S M5 x 40 mm Ne hexagonal socket screw Hexagonal wrench M5 Step 3 Mounting the copyboard on the stand Check again that the caster stoppers are locked Catch the upper brackets left and right on the back surface of the copyboard to the front surface of the stand the side on which the feet pipes are longer Loosen the M3 screws of the lower sheet nuts then tighten the screws lining them up with the positions of the holes in the vertical pipes left and right Mount the lower brackets for vertical installation to the stand using the M5 x 40 hexagonal socket screws flat washers 25 5 mm bore diameter and M8 cap nuts left and right M5 x 40 Hexagonal wrench M5 flat washers socket screw Nes o TR 05 5 mm bore Cap nuts diameter M5 T T hexagonal of 10 installation I Lower bracket for O i 0 A Rs 2 C e 4 Sheet nut M3 screw Front surface Insert the USB e
6. d M4 x 6 screws Do not let the screws pass through the board Insert the pen tray s rail into the rail groove at the bottom of the copyboard Now lift the pen tray to catch it on the copyboard then tighten the screws to fasten the pen tray in place positions B and D D Upper bracket Flat washers M5 x 8 hexagonal socket screw Hexagonal wrench M5 f Lower bracket for horizontal installation Main unit JENE Sheet nut insertion slot Used when mounting at a height of 1450 mm A Used when mounting at a height of 1700 mm JID 1700mm 1450mm Stand Or O v M4 x 6 screw tom of copyboard Rail groove in bot Pen tray rail Rail groove in bottom of copyboard 4 Mount the adapter holder The adapter holder is for stowing the AC power adapter Temporarily fasten the adapter holder in place at 2 points using the included M4 x 6 screws Do not let the screws pass through the board Insert the adapter holder s rail into the pen tray s rail groove Now lift the adapter holder to catch it on the pen tray then tighten the screws to fasten the adapter holder in place The position in which the adapter holder is mounted can be changed to the left side of the rail groove on the bottom of the copyboard M4 x 6 screws 2 points Rail groove in pen tray
7. i M4 x 6 screw S rail J OS Now lift the adapter holder to catch it on the pen tray then tighten the screws to fasten the adapter holder in place Step 2 Assembling the stand 1 Mount the vertical pipes to the feet pipes two Use the feet washers flat washers 98 5 mm bore diameter spring washers M8 x 50 mm hexagonal socket screws and the included hexagonal wrench M8 to securely fasten the vertical pipes and feet pipes Insert the vertical pipe caps into the vertical pipes Insert the feet pipe caps into the feet pipes front and back gt Vertical pipe cap 68 5 mm bore diameter Spring washer socket screw Flat washer ae 2 G V EBS a 2a amp M8 x 50 mm hexagonal Feet washer Ww Hexagonal wrench M8 Vertical pipe e When mounting is finished push the stoppers of the four casters to the lock side to lock the caster If the casters are not locked the stand will be unstable during assembly and this could lead to injury Locking unlocking the caster stoppers Press the bottom of the caster stopper to lock the caster Press the top to unlock Unlock Lock A Caster stopper Feet pipe cap 2 Mount the two transverse pipes to the vertical pipes Use the two short pipes 687 mm as the transverse pipes Use the flat washers 85 5 mm
8. le for when the wall outlet is on the right side Use the same procedure to attach the cable clips and secure the power cord when the wall outlet is on the left side or elsewhere This completes installation of the stand Check again that the copyboard is securely mounted on the stand and that the various screws are securely tightened Set the copyboard s software for vertical installation The software is set for horizontal installation upon shipment from the factory Refer to the PLUS TOOLBOX software manual included with the copyboard and select Vertical at Position under Hardware Setup USB connector DC plug USB connector AC power adapter included with copyboard AC power cord included with copyboard
9. ocket screw Hexagonal wrench Feet pipe cap Transverse pipes for horizontal installation Ne Flat washer 5 5 mm bore diameter K hexagonal N socket screw M5 x 40 mm Hexagonal wrench M5 Step 3 Mounting the copyboard on the stand Check again that the caster stoppers are locked Transverse pipes for horizontal installation Catch the upper brackets left and right on the back surface of the copyboard to the front side of the stand the side on which the feet pipes are longer Loosen the M3 screws of the lower sheet nuts then tighten the screws lining them up with the positions of the holes in the vertical pipes left and right Mount the lower brackets for horizontal installation to the stand using the M5 x 40 hexagonal socket screws flat washers 95 5 mm bore diameter and M8 cap nuts left and right XZ Front surface B M5 x 40 he nt screw 7 Hexagonal wrench M5 Flat washers 05 5 mm bore diameter Lower bracket horizontal installation T rT T xagonal socket e N Cap nuts M5 for Step 4 Fastening the power cord to the stand Refer to the Copyboard CR 5 User s Manual for instructions on connecting the copyboard and AC power adapter Five 5 cable clips are included Use them to conceal the cord behind
10. ove three on the left two on the right When doing this for the left side start by inserting first the sheet nut to which no screw is attached This sheet nut is used to fasten the USB connector bracket position adjustable Step 4 Mounting the USB extension cable The left and right sides referred to here are as seen when looking at the copyboard from the 1840mm front Slide the sheet nuts with screws to their mounting positions in the rail groove and tighten the screws with the screw heads inserted into the round cut The mounting height is fixed to 1840 mm The positions of the round cuts in the rail groove are the positions for mounting the sheet nuts to mount the copyboard Mounting position for sheet nut with no screw as desired Top control panel side Rail groove Upper mount position Lower mount position WS Sheet nut insertion slot SS Sheet nut Round cut Main unit Step 5 Fastening the power cord to the stand Mount the USB connector bracket within this range as desired lt Upper mount position lt Lower mount position lt Sheet nut insertion slot Stand Bottom M3 screw 2 Mount the brackets to the sheet nuts left and right Securely fasten the upper bracket to the upper sheet nuts
11. the copyboard Peel off the backing of the cable clips and attach them in the desired positions Backing S Place the power cord through the cable clips Push down the clip section to lock the clip This completes installation of the stand Check again that the copyboard is securely mounted on the stand and that the various screws are securely tightened Sheet nut M3 screw AC power adapter DC plug included with copyboard AC power cord included with copyboard This diagram shows an exampl e for when the wall outlet is on the right side Use the same procedure to attach the cable clips and secure the power cord when the wall outlet is on the left side or elsewhere Assembly for Vertical Installation Flow of assembly and installation a a Step 1 Step 2 Step 3 Mounting parts Assembling Mounting the on the copyboard the stand copyboard on the stand Step 1 Mounting parts on the copyboard 1 Mount the sheet nuts two on the right three on the left in the rail groove Attach M3 x 4 screws to the four sheet nuts Be sure they do not stick out beyond the thickness of the sheets Do not attach a screw to one of the sheet nuts Insert the sheet nuts into the sheet nut insertion slots in the rail gro
12. the sheet nut insertion slots in the rail groove two on the left two on the right Slide the nuts to their mounting position see the diagram at the right and tighten the screws with the screw heads inserted into the round cut The diagram below is for when thickness mounting of the sheets at a height of 1450 mm positions Selecting the stand mount height The positions of the four round cuts in the rail groove are the sheet nut mount When mounting at a height of 1450 mm Mount the sheet nuts to sheet nut mount positions A and C When mounting at a height of 1700 mm Mount the sheet nuts to sheet nut mount ja gt gt a Step 1 Step 2 Step 3 Step d Mounting parts Assembling Mounting the Fastening the on the copyboard the stand copyboard on power cord the stand to the stand lt d d lt Sheet nut Round cut M3 screw Bottom 2 Mount the brackets to the sheet nuts left and right Securely fasten the upper bracket to the upper sheet nuts using two M5 x 8 hexagonal socket screws and flat washers 65 5 mm bore diameter Temporarily fasten the lower bracket for horizontal installation to the screw hole in the lower sheet nut using one M5 x 8 hexagonal socket screw and flat washer 05 5 mm bore diameter 3 Mount the pen tray to the bottom of the copyboard Temporarily fasten the pen tray in place at 2 points using the include
13. xtension cable s USB connector into the USB port on the copyboard oN 5 To install at an angle mount the screws to the 5 or 10 holes Attach the USB extension cable s USB connector port USB cable side to the USB connector bracket using two M3 screws Put the USB cable into the rail groove in the copyboard Slide the sheet nut to the position for attaching the USB connector bracket as desired then fasten the USB connector bracket using two M5 x 8 hexagonal socket screws and flat washers 25 5 mm bore diameter USB connector bracket USB connector Flat washers 95 5 mm be diameter M5 x8 A hexagonal O socket screw y Hexagonal wrench M5 Step 5 Fastening the power cord to the stand Refer to the Copyboard CR 5 User s Manual for instructions on connecting the copyboard and AC power adapter Five 5 cable clips are included Use them to conceal the cord behind the copyboard Backing Peel off the backing of the cable clips and attach them in the desired positions Place the power cord through the cable clips When cable clips have been attached to the top of the copyboard also pass the USB cable through them Push down the clip section to lock the clip This diagram shows an examp
Download Pdf Manuals
Related Search