Home
User manual
Contents
1. Important The rinse aid dispenser is fitted on all models the detergent dispenser only on some If both dispensers are present put the external detergent and rinse aid containers in place and insert the respective intake hoses on the rear of the machine into them Red hose detergent blue hose rinse aid Before inserting the hoses into the containers fit the weights needed to ensure that they always draw in liquid from the bottoms of the containers and the filters onto their ends as shown If the detergent dispenser is not factory fitted it can be by ordering the relative kit As an alternative an external dispenser can be fitted making the electrical connection by means of an H05 RN F 2x0 5 mm electrical cable which can be laid along the route shown in the TECHNICAL DATA diagram and connected as shown in the wiring diagram supplied with the dishwasher The dispenser must operate on 230V 50 Hz with maximum power absorption of 15 W Connect to the detergent dispenser outside the dishwasher using the red hose mentioned above IMPORTANT Whenever the type of detergent or rinse aid is changed it is ABSOLUTELY ESSENTIAL to flush out the peristaltic pumps by placing the external intake pipes in water for a few cycles Always use only products specifically recommended for use in a dishwasher The internal pipes of the detergent and rinse paid pumps should be replaced by the After Sales Service every 12 months or 15 000 wash cycl
2. E ELECTRICITY SUPPLY CABLE P PERISTALTIC HOSES DRAIN HOSE T EXTERNAL DISPENSER POWER SUPPLY CABLE ENTRY POINT TERMINAL BOARD A A MIN 820 3 Installation and positioning INSTALLATION and POSITIONING Bring the dishwasher to the installation site remove the packaging and check the appliance and components for damage any damage found must be reported to the transporter in writing The packaging components plastic bags expanded polystyrene nails etc must not be left within reach of children and pets since they are potentially dangerous All packaging materials used are environment friendly They can be kept without constituting any hazard or may be disposed of at a specialist waste disposal centre The plastic components suitable for recycling are marked as follows PE polyethylene external packaging film bag containing the instructions protective bags PP polypropylene straps PS expanded polystyrene corner guards top of packaging Wooden and cardboard components can be disposed of in accordance with the relevant regulations When the product is decommissioned it must not be dumped in the environment it must be disposed of in accordance with the relevant regulations All metal parts are in stainless steel and can be removed The plastic parts are marked with the symbol identifying the material used Models with aquastop The aquastop device prevents flooding in the event of water leaks In these models the
3. End flashes on the display The display returns to showing P1 Close the door again to start filling the tank prior to performance of a new wash cycle Remove the filters simply lift them out as shown here taking care that no large residues fall into the sump underneath Clean them to remove residues and rinse with plenty of water then put them correctly back in place do_not use sharp or pointed tools Clean away any limescale deposits to prevent excessive build ups If possible leave the door ajar when not in use Clean surfaces thoroughly and often with a damp cloth use neutral non abrasive detergents which do not use chlorine compounds which corrode and damage stainless steel Do not use the products mentioned above even when cleaning the floor underneath or in the vicinity of the dishwasher to ensure that fumes or drops cannot damage the steel surfaces IMPORTANT The dishwasher automatically performs program PO at the start of the day if water has been left in the tank and has dropped below the temperature of 40 C GA m 11 2 Periodic checks Remove the top and bottom spray arms by unscrewing the central screw and unscrew the caps from the ends of the rinsing arms as shown Do not unscrew the nozzles Clean the holes and nozzles under a jet of clean running water do not use tools which might cause damage Reassemble the spray arms with care Clean the outside of the appliance with a da
4. Only one supplementary function can be selected for each program 10 1 Selecting the glassware function available in P1 P2 Reduces the program s rinsing temperature and duration Select the program required Pr RSS Hold down to select the glassware function then ne to confirm the program start 10 2 Selecting the extra rinse function available in P1 P2 P3 P4 Extends the duration of the rinse Select the program required 7 4 OPERATION Hold down to select the extra rinse function then gt to confirm the program start 15 10 3 Selecting the sanitisation function only available in P3 Increases the washing and rinsing temperature and the program duration Select the program required Foam Press to select the sanitisation function then D to confirm the program start the Sapa enana na remains selected until the program is changed or the dishwasher is switched off by pressing the button During the selected program the display alternates between showing the supplementary function and the duration LOADING THE DISHES Plates The basket is able to take 12 soup plates or 18 dinner plates Remove solid residues bones fruit peel stones etc and soak plates with dried residues of cheese egg etc in water before loading in the dishwasher Glasses Load glasses upside down Cutlery Use the special basket s Load cutlery loose preferably with the handle at th
5. the display Top up with salt when there is no water in the tank to prevent washing water from getting into the water softener device Caution use only salt of the specific type do not use cooking salt The salt tank has a capacity of about 1 kg of coarse grained salt The salt reservoir is in the bottom of the tank After removing the basket undo the cap and pour the salt in using the funnel supplied Remove any salt residues around the opening before screwing the cap back on 11 MAINTENANCE AND CLEANING Although no particular scheduled maintenance is required users are advised to have the dishwasher checked by a specialist technician twice a year N B the manufacturer accepts no liability for wilful damage or damage deriving from carelessness neglect failure to comply with instructions regulations and standards or incorrect connections 11 1 Daily cleaning The dishwasher has IPX4 protection but the use of direct water jets for cleaning is forbidden Cleaning the filter during the day In case of particularly heavy duty working conditions the filter should be cleaned every 30 40 cycles keeping the machine in operating conditions to do this carry out the partial tank pump out routine program PO EA R ae od a oe B Press the button and hold it down until P0 and the duration of 1 appear on the display Confirm by pressing gt light L2 turns orange At the end of the pump out the word
6. AND FOR PEOPLE ANIMALS OR ANY OBJECT LEANING OR SITTING ON THE OPEN DOOR OF THE DISHWASHER MIGHT CAUSE IT TO TIP OVER PUTTING PEOPLE IN DANGER NEVER LEAVE THE DISHWASHER DOOR OPEN SINCE PEOPLE MIGHT TRIP OVER IT DO NOT DRINK ANY WATER LEFT IN THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM THE APPLIANCE IS NOT SUITABLE FOR USE BY JUVENILES OR PERSONS WITH REDUCED PHYSICAL SENSORIAL OR MENTAL CAPACITIES OR THOSE WITHOUT THE NECESSARY KNOWLEDGE AND EXPERIENCE SUCH PERSONS MAY ONLY USE THE APPLIANCE UNDER THE SUPERVISION OF A PERSON RESPONSIBLE FOR THEIR SAFETY gt gt D D 2 Technical data TECHNICAL DATA Supply voltage V convertible to single phase version V Frequency Hz Max power absorption at 400V 3N kW PBB Max power absorption at 230V 1N kW Boiler heating element power at 400V 3N kW Po BO Boiler heating element power at 230V 1N kW Tank heating element power kW a S Water intake pressure kPa bar 100 600 1 6 Water intake temperature C Water hardness models with softener dF Rinse cycle water consumption Boiler capacity 1 Tank capacity Standard cycle duration with intake water at 50 C S Noise level dB A o O Degree of protection IPX Net weight kg ee Power supply cable type HARP P 0OVBN 230V1N pe S C a 2 8 kW 2 8 kW C Power Supply Cable S Master Switch R LOWER BACK PANEL FILLER HOSE EARTH TERMINAL
7. FETY CEI EN IEC 60335 2 58 61770 AND ELECTROMAGNETIC COMPATIBILITY CEI IEC EN 55014 1 2 61000 3 4 50366 THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR INJURY OR DAMAGE CAUSED BY FAILURE TO COMPLY WITH THE ABOVE REGULATIONS OR DERIVING FROM INCORRECT USE TAMPERING WITH EVEN JUST ONE PART OF THE APPLIANCE AND THE USE OF NON ORIGINAL SPARE PARTS THE APPLIANCE MUST BE IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY i REGULATIONS THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002 96 EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT WEE BY MAKING SURE THAT THIS PRODUCT IS DISPOSED OF CORRECTLY THE USER HELPS TO PREVENT POTENTIAL DETRIMENTAL EFFECTS ON HEALTH AND THE ENVIRONMENT THE A SYMBOL ON THE PRODUCT OR IN THE TECHNICAL DOCUMENTATION INDICATES THAT THIS PRODUCT MUST NOT BE TREATED AS ORDINARY DOMESTIC WASTE BUT MUST BE CONSIGNED TO THE SPECIAL COLLECTION POINT FOR THE RECYCLING OF ELECTRICAL AND ELECTRONIC EQUIPMENT WHEN DECOMMISSIONING THE APPLIANCE COMPLY WITH THE LOCAL WASTE DISPOSAL REGULATIONS FOR FURTHER INFORMATION ON THE TREATMENT RECOVERY AND RECYCLING OF THIS PRODUCT CONTACT THE COMPETENT LOCAL OFFICE THE DOMESTIC WASTE COLLECTION SERVICE OR THE SHOP WHERE THE PRODUCT WAS PURCHASED NEVER PLACE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE WHICH MIGHT CAUSE AN EXPLOSION INSIDE THE APPLIANCE NEVER LOAD DISHES DIRTY WITH ASH WAX OR PAINTS NEVER USE THE DISHWASHER OR ANY PART OF IT AS A LADDER SUPPORT OR ST
8. PROFESSIONAL DISHWASHER CEN 1 Precautions for safety and use 2 Technical data 3 Installation and positioning 4 INSTALLATION INSTRUCTIONS FOR THE AFTER SALES SERVICE 5 Start up 6 Settings 7 Malfunctions shown on the display for the technician 8 INSTRUCTIONS FOR THE USER 9 Choosing the program 10 Supplementary Functions 11 Maintenance and cleaning 12 Troubleshooting 13 Malfunctions shown on the display for the user You are advised to read all the instructions in this manual carefully to become familiar with the right conditions for the proper use of your dishwasher TECHNICAL INSTRUCTIONS These are intended for the qualified staff who are to install commission and test the appliance and carry out any servicing and repairs These provide recommendations for use a description of the controls and the correct procedures for cleaning and maintaining the dishwasher 1 Precautions for safety and use THIS MANUAL IS AN INTEGRAL PART OF THE DISHWASHER AND MUST ALWAYS BE KEPT WITH THE APPLIANCE POSITIONING CONNECTIONS COMMISSIONING TROUBLESHOOTING AND REPLACEMENT OF THE POWER SUPPLY CABLE MUST BE CARRIED OUT BY SKILLED STAFF THE DISHWASHER IS INTENDED ONLY FOR PROFESSIONAL USE BY TRAINED STAFF IT IS DESIGNED TO WASH TABLEWARE PLATES CUPS BOWLS OVEN DISHES AND CUTLERY AND SIMILAR ITEMS IN THE RESTAURANT AND INSTITUTIONAL CATERING SECTOR AND COMPLIES WITH THE INTERNATIONAL STANDARDS ON ELECTRICAL AND MECHANICAL SA
9. after the parameter modification procedure explained in the previous point Indicator lights as follows O off green orange flashing With the dishwasher powered up access programming mode by pressing the on off button for a few seconds at the beep release the button and press it again quickly within 0 5 seconds The peristaltic pumps continue to operate until the same buttons are pressed again The rinse aid and detergent symbol lights remain on as long as work is in progress bear in mind that the rinse aid peristaltic pump fills the circuit in about 7 minutes while for the detergent it only takes 2 minutes 7 MALFUNCTIONS SHOWN ON THE DISPLAY The dishwasher is able to identify a number of malfunctions and show them on the display If the problem persists after the dishwasher has been switched off and back on proceed as described below The anti flooding system has been activated oa Eron for the relevant models only Large water leak check the origin of the problem Erro4 Tank temperature probe malfunction Tank temperature probe disconnected or not working Check dynamic pressure in intake system inspect water intake filter and clean if necessary If the problem persists tank pressure switch has failed continuous empty reading leak from pipe connected to air trap valve vent exhaust pipe blocked Tank water filling malfunction Inspect the filters for dirt and that the drain ho
10. d for the dishwasher must serve this appliance only The user must have a master switch and a differential safety breaker with rating suitable for the machine s characteristics installed on the electricity supply line in accordance with the relevant regulations These switches must be installed close to the dishwasher be easily accessible after installation and provide complete disconnection from the electrical mains in overvoltage class IIl conditions Warning The dishwasher is always powered up unless the master switch is turned off Connect the appliance to the user s earth system The Y terminal for the connection is in the bottom right hand corner of the appliance The earth wire PE is yellow green in colour the neutral wire N is blue and the live wires L1 L2 L3 are black grey and brown In the event of single phase connection 230V 1N the connection to the electrical mains must be made using a cable with plug compliant with the relevant regulations IN THE EVENT OF DAMAGE TO THE SUPPLY CORD HAVE IT REPLACED BY THE MANUFACTURER OR AN AUTHORIZED TECHNICAL SERVICE CENTRE IN ORDER TO AVOID ANY RISK 5 START UP FIRST START UP The electrical protection system must undergo a functional test before the appliance is put into operation The appliance must be installed and or inspected by the qualified staff who will start it up for the first time and provide the relevant operating instructions PREPARING FOR USE
11. e bottom taking care not to injure yourself with fork prongs or knife blades TOTAL PUMP OUT AT THE END OF THE DAY The dishwasher is able to perform an automatic cleaning cycle at the end of the day Press the button UnLo and the duration appear on the display 8 S aie m Confirm by pressing gt light L2 turns orange OFF 9 At the end of the pump out the appliance sets in oY Ae OFF status 16 After a total pump out the filters should be cleaned as described above Never switch the dishwasher off with water in the tank pump out first TOTAL PUMP OUT AT THE END OF THE DAY Resin regeneration form models with water softener From time to time on models with water softener before the total pump out at the end of the day the user will automatically be reminded to carry out the resin regeneration cycle required after a number of washes which depends on the hardness of the water about 30 for average setting H03 In this case the sequence will be as follows Press the pump out button rEgE and the duration appear on the display E W209 gt oY seca a Confirm by pressing gt light L2 turns orange L OFF At the end of the pump out the appliance sets in oY D OFP status Topping up with regenerating salt for models with water softener Salt must be added when the no salt light appears on
12. en the door is closed Set at off for cycle start after confirmation with the start button 6 1 6 Regeneration frequency setup models with softener e Default value H00 modify the parameter to suit the mains water hardness e Generally H03 will be satisfactory for most users e At first use the salt tank has to be filled It is subsequently sufficient simply to fill up with regenerating salt when necessary Hardness Hardness dH german dF French Setting level Modify the value degrees degrees of the parameter Regeneration off Regeneration off by pressing With values over 60 dF an external water treatment device must be used and the regeneration frequency must be set on HOO 6 1 7 Customisation of duration of program P4 The duration of program P4 can be customised from 5 to 20 minutes using the appliance parameter modification procedure but the dishwasher must be set on program P4 After setting program P4 access the programming P fir procedure and scroll through to mF last parameter to ae appear then press the button to modify the duration of the cycle from 5 to 20 minutes After a few seconds without the user pressing any buttons the display will return to the normal operating O P 00 10 00 O ae status and the modifications will be saved TOO 2 10 6 2 Starting the peristaltic pumps rapid filling of detergent and rinse aid delivery circuit Perform
13. es Failure to comply with this recommendation leads to forfeiture of the warranty entitlement on the appliance s water system 6 SETTINGS Ai SETTINGS l During start up the functions parameters listed below must be set or adjusted On first installation a series of operations can be performed to allow the dishwasher to be customised to the user s needs A short testing cycle can also be performed to verify operation of all the components To perform these operations access programming mode as explained below 6 1 Dishwasher parameter modification procedure Indicator lights as follows O off green orange flashing Access programming mode by pressing the on off button for a few seconds UnLo 1 58 will appear on the display with the appliance on after the filling and heating phase at the beep release the button and press it again quickly within 0 5 seconds Keep pressing the button again to scroll through all the modifiable parameters in the following order Rinse aid delivery amount Detergent delivery amount Rinsing temperature Washing temperature Start on start off Set at on to start the cycle when the door is closed Set at off for cycle start after confirmation with the start button Regeneration frequency depending on water hardness if softener is installed Customisation of duration of program P4 N B the machine must be set on P4 see 6 7 Set
14. filling WASHING PROGRAM DOES NOT START If the word CLOSE remains on the The word CLOSE remains on the display even with the door closed call display the after sales service Spray arm washing holes blocked Remove spray arms and clean them by dirt or limescale 10 2 Periodic checks Filter fouled See Cleaning the filter during the day Too little or unsuitable detergent or raee aid Check type and quantity of detergent Check that the detergent intake pipe Detergent intake blocked underneath the filter is unobstructed T in photo No or not enough detergent or rinse aid being supplied detergent or rinse aid not being taken from the relative container POOR WASHING RESULTS Pipe inside detergent and or rinse aid peristaltic pump worn or broke have it replaced by the After Sales Service Plates glasses badly arranged Arrange plates glasses correctly Check temperature shown on the Low washing temperature display call the after sales service if less than 50 Increase washing duration especially Inappropriate cycle set if dishes are very dirty or dirt has dried on Check that nozzles are clean and ensure that the softener is working properly if installed Spray arm nozzles fouled INADEQUATE RINSING l Limescale in boiler Rinse aid unsuitable or not being Check container of rinse aid and STAINS ON GLASSES AND delivered correctly whether type is suitable for the mains CUTLERY Water hard
15. he display containers container if the dishwasher 8 3 FIRST USE EACH DAY tank and boiler empty Indicator lights as follows O off green orange xt flashing Display shows Actions and what happens With the door closed j Press and hold it down the dishwasher fills the tank after the water in the boiler has heated up light L2 shows orange and the boiler heating element symbol appears on the display Wait for P1 to appear and LED L1 to change from orange to green the tank heating element comes on until the set temperature is reached The duration of this stage may vary depending on the mains water temperature and on the single phase connection Press the button to display the tank left and boiler right temperatures Load the dishes Select the program required by pressing Confirm the program start by pressing 2 and holding it down for 1 second light L2 changes from green to orange 13 Cycle in progress the time left until the end of the cycle ae i is displayed If the door is opened CLOSE flashes and a6 Dj o amp the program stops when it is closed again the program restarts from the beginning At the end of the program End flashes Unload the dishes With the door closed to change to a fresh program instead of repeating the last one press the button The programs available are displayed light L2 changes from orange to green If a p
16. intake tap is on and the dynamic pressure in intake system inspect water intake filter and clean if necessary If the problem persists contact the After Sales Service Water pump out malfunction dishwasher is left full of water Boiler water filling malfunction Check that the rinsing spray arm nozzles are not fouled Boiler emptying malfunction If the problem persists contact the After Sales Service Boiler emptying malfunction with tank full Contact the After Sales Service Err28 Boiler heating malfunction overheating 20
17. mp cloth and neutral soap rinsing and drying thoroughly 11 3 Lengthy periods out of use If the dishwasher is to be out of use for a fairly long period of time the detergent and rinse aid dispenser devices must be emptied to prevent crystallisation and damage to the pumps Remove the intake hoses from the detergent and rinse aid containers and place them in a container of clean water then perform a few wash cycles followed by a complete pump out Finally turn off the master switch close the water intake valve and leave the door ajar until the interior is completely dry The detergent and rinse aid intake hoses must be put back into the containers when the dishwasher is returned to service taking care not to swap them over red hose detergent blue hose rinse aid 18 12 TROUBLESHOOTING If the system fails to pump out because the drain pump is fouled as a result of incorrect filter positioning proceed as follows Bale out the dishwasher with a basin and disconnect it from the electrical mains Unscrew the screw A release the tang B and lift it Check that the impeller of the drain pump underneath the cover turns freely and is free from dirt limescale residues or pieces of glass Never use tools screwdrivers scissors etc PROBLEM POSSIBLE CAUSE POSSIBLE REMEDY LIGHT S1 DOES NOT COME ON Mains power failure Check electrical mains connection The dishwasher has not yet wait for the word FILL to go out finished
18. ness above 12 dF or water If the problem persists contact large amounts of dissolved salts the after sales service 19 Check that the dishwasher drain hose WATER IN TANK AFTER PUMP Drain hose incorrectly positioned and rain are unobstructed and the OUT or partially obstructed drain is not too high up see connection diagram 13 MALFUNCTIONS SHOWN ON THE DISPLAY The dishwasher is able to identify a number of malfunctions and show them on the display If the problem persists after the dishwasher has been switched off and back on proceed as described below The anti flooding system has been activated not for the relevant models only Contact the After Sales Service Eros Tank temperature probe malfunction Contact the After Sales Service Check that the water intake tap is on and the dynamic pressure in the intake system inspect the water intake filter and clean if necessary If the problem persists contact the After Sales Service Tank water filling malfunction Inspect the filters for dirt and check that the drain hose is not blocked bent or crushed Check that the drain pump is not blocked by dirt proceed as described in point 10 2 Periodic checks If the problem persists contact the After Sales Service Erro9 Tank water level too high Err23 Boiler heating malfunction does not heat Contact the After Sales Service up Err24 Boiler temperature probe malfunction Check that the water
19. pressure switch has failed continuous empty reading 8 1 Control panel L1 L2 Program selection button ee mer Start CONFIRM PAUSE button Total emptying button tank and boiler Additional function selection button L1 Main power on light em L2 Intake standby cycle in progress light orange green L3 Pump out in progress light No rinse aid symbol if a system for monitoring outside the dishwasher is provided Tank heating element on symbol No salt symbol if softener is fitted Boiler element on symbol No detergent symbol if a system for monitoring outside the dishwasher is provided 12 8 2 Before washing Use only detergents and rinse aids for industrial dishwashers Do not use detergents intended for hand washing We recommend the use of Smeg products specially developed for this dishwasher When topping up the tanks take care not to swap the products this might damage the dishwasher and cause malfunctions Do not mix different detergents this would damage the dispenser device Industrial dishwasher detergents may cause serious irritations Comply carefully with the instructions provided by the detergent producer on the pack Tamm on he re Fit tre mar mains water The level of That there is That the filters are in place switch user the tap user detergent and regenerating salt the spray arms rotate and word OFF appears rinse aid in the in the relative there are no foreign bodies in on t
20. rogram has already started hold gt down to e00 erupt it oQO ye change the program by pressing Confirm the program start by pressing gt and holding it 4 00 down for 1 second light L2 changes back to orange N B During heating of the water in the boiler the tank heating element E and boiler heating element e symbols may appear on the display Filter presence sensor on some models only The filter is fitted with a sensor which checks that it is properly fitted if it is not in the correct position the word FiLter appears on the display 14 9 CHOOSING THE PROGRAM PROGRAM TYPE OF DIRT DURATION a ee Ce Or e e iseanan 1 with glassware function active 2 with glassware function active Very dirty dishes and cutlery Long about 4 5 30 with sani function active P4 Depending on the duration set As required from 5 to 20 The cycle duration stated above refers to three phase appliances supplied with hot water at 50 C If the appliance is supplied with cold water the cycle duration might increase depending on the intake water temperature since the dishwasher is fitted with the HTR system which requires set temperature and pressure for rinsing 10 SUPPLEMENTARY FUNCTIONS Indicator lights as follows O off green orange lt t flashing To select a supplementary function when the program required is shown on the display P1 P2 P3 or P4 press the button
21. se is not blocked bent or crushed Check that the drain pump is not blocked by dirt by removing the insert on the sump from inside the tank If the problem persists with the tank empty tank pressure switch defect the contact is locked on full with tank full drain pump has failed with tank full see above water pump out malfunction Tank water level too high with tank empty safety pressure defect the contact is locked on full Water pump out malfunction circuit board relay failure contactor failure Boiler heating malfunction does not heat boiler safety thermostat failure up boiler temperature probe faulty or incorrectly positioned water continues to enter the tank due to tank pressure switch defect Err24 Boiler temperature probe malfunction boiler temperature probe disconnected or not working 11 pipe leaking disconnected check that rinsing spray arm nozzles are clean Boiler emptying malfunction boiler pressure switch has failed continuous full reading rinsing pump not working Boiler emptying malfunction with tank full Boiler pressure switch has failed continuous full reading e128 Boiler heating malfunction overheating Senden ta UrE pO 8 INSTRUCTIONS FOR THE USER Check that the water intake tap is on and the dynamic pressure in the intake system inspect the water intake filter and clean if necessary Boiler water filling malfunction If the problem persists boiler
22. ting program P4 duration Displaying the cycle count When scrolling through the appliance parameters the item TL 856868 the total count of the cycles the dishwasher has performed since ree llation will be found This parameter cannot be modified or reset unless the software is reprogrammed O OO R 4 o O a re 88888 fre 8888 Di o wQO Indicator lights as follows O off green orange lt t flashing 6 1 1 Setting up rinse aid delivery Modify the value of the parameter by pressing Delivery time s Delivery quantity c c 0 0 6 0 7 12 1 3 default value factory preset 18 2 0 24 2 7 30 355 26 4 0 48 5 3 6 1 2 Setting up detergent delivery F A DETERGENT gt Modify the value of the parameter TOLA by pressing Delivery time Delivery s quantity c c oo ee a default value factory preset 6 1 3 Rinsing temperature setup Modify the value of the parameter by pressing Default value 85 C Min 71 C max 85 C QQ j l WO IEAn be m gt 00 gt Modify the value of the parameter by pressing i SEY SHY Default value 62 C Min 52 C max 62 C Indicator lights as follows O off green orange 4 flashing 6 1 5 Autostart function Modify the parameter ON OFF by pressing Set at on to start the cycle wh
23. tted The dynamic intake pressure must be between 1 and 6 bar if it is higher installation of a pressure reducer is recommended It is essential to fit a main stop tap on the water intake pipeline the tap must be accessible after installation of the appliance so do not install it behind the dishwasher The stated cycle duration refers to appliances supplied with hot water at 50 C If the appliance is supplied with cold water the cycle duration might increase depending on the intake water temperature since the dishwasher is fitted with the HTR system which requires set temperature and pressure for rinsing Drainage The dishwasher is fitted with a drain pump and can operate with drain connections on the floor or wall AN Caution make sure that the intake and drain hoses are not bent constricted or crushed after installation If the drain connection is to an outlet with valve the maximum height of the drain is reduced to 600 mm In all cases after installation check that the drain is fully functional by pumping out the tank completely PO cycle At 4 1 Electrical connection A The dishwasher and any additional equipment must be connected to the electrical system by authorised skilled staff in accordance with the relevant regulations also comply with the technical instructions for the connection The total rated power is stated on the appliance s technical data plate The electrical protection devices fitte
24. water intake hose is fitted with a solenoid valve Do not cut the hose and do not drop the solenoid valve into water In the event of damage to the water intake hose disconnect the appliance from the electricity supply POSITIONING Caution the indoor system and premises in which equipment for institutions is installed must comply with the relevant regulations The manufacturer declines all liability for direct or indirect injury or damage deriving from failure to comply with these regulations Before installation check that there are no objects or materials in the vicinity which may be damaged by steam or splashes of washing solution or that any such items are suitably protected Place the dishwasher in the chosen point and remove the protective film Level the dishwasher with the aid of a spirit level on its adjustable feet to ensure that it is stable all other mounting solutions must be approved by the manufacturer 4 INSTALLATION INSTRUCTIONS FOR THE AFTER SALES SERVICE At 4 1 Water connection Water supply and drain connection The water pipelines and electricity supply cable lead out of the bottom right hand corner of the appliance Connect the water intake hose to a connector with 3 4 gas threaded fitting fitting the filter A provided in models with aquastop the filter and ring nut form a single unit The connection to the water mains must only be made with new hoses the use of old or worn hoses is not permi
Download Pdf Manuals
Related Search
Related Contents
Tacens Radix III 420 取扱説明書 ジグソー Philips Softone ESaver E14, 5W LG DR787T Specifications Tiger PID Manual RCP1000_UM_UK_d4 Network Cameras ArchimedesMB User Manual Audiovox CDM-8200 Cordless Telephone User Manual Copyright © All rights reserved.
Failed to retrieve file