Home
EV S155(E) 网站版
Contents
1. DPress the ENTER button in AUTO menu then enter to the running the auto run auto programming program 2 Press the UP DOWN button to select ATO1 AT05 SPEED CHASEO1 CHASE05 3 Press the ENTER button to start running 5 9 EDIT AUTO PROGRAMMING PROGRAM 1 Press the ENTER button in PROGRAM menu then enter to the editing auto programming program 2 Press the UP DOWN button to select CHASEO1 CHASEO5 3 Press the ENTER button for confirmation and enter to the next menu 4 Press the UP DOWN button to select SCENEO1 SCENE20 5 Press the ENTER button for confirmation and enter to the next menu 6 Then press the UP DOWN button to select RED GREEN J BLUE WHITE AMBER Ultra Violet SHUT TIME warr 1 USE 7 Press the UP DOWN button to set up the parameter which are needed 8 Press the ENTER button to escape and save Illustrations When USE is set to be NO or the TIME parameter of TIME is 0 it will not run this scene When WAIT is set to be FADE time the running process isas the right chart showing X 5 10 CHECK THE LIGHTING INFORMATION 1 Press the ENTER J button in INFO menu then enter to the checking the lighting information 2 SOFT button is for software version information 3 LEDs button is for the LED quantity information 4 POW button is for the current information of power reduction It is 10096 output in no
2. UP DOWN button to select R G EB Ew 1 A1 wv 3 Press the UP DOWN button to set up the 0 255 numerical value 4 On the USE interface pressing ON button means valid otherwise OFF button invalid 5 Press the ENTER button to escape and save Illustrations When pressing the ON button which means valid on the USE interface the actual output value of RED GREEN BLUE WHITE is output in accordance with the percentage which the color cast calibration value divides 255 5 5 CHANNEL MODE SETTING 1 Press the ENTER button in CHMD menu then enter to the channel mode setting 2 Press the UP DOWN button to select 12cH 9CH 7cH 6cH 3 Press the ENTER button to escape and save 5 6 DIMMING MODE SETTING Illustrations When setting OFF in DIM menu there will be no delay dimming effect The dimming speed of DIMI DIM4 is from fast to slow It will be set OFF automatically in DIM menu when showing the shutter effect 1 Press the ENTER button in DIM menu then enter to the dimming mode setting 2 Press the UP DOWN button to select OFF DiM1 DIM2 DIM3 and DIM4 3 Press the ENTER button to escape and save 5 7 DISPLAY SETTING 1 Press the ENTER button in DISY menu then enter to the display setting 2 Press the UP DOWN button to select ON 2 MINITES OFF 3 Press the ENTER button to escape and save 5 8 RUN THE AUTO RUN AUTO PROGRAMMING PROGRAM
3. in series connection pattern the amount of the lighting can not be more than 32 PCS not available in parallel connection pattern Must add a signal Pn n 5 1S a se amplifier if the length of signal line exceeds 60M between controller and lighting or between OMIN two lightings l 2 R RED In the controller mode at the last fixture in the chain the DMX output GREEN has to be connected with a DMX terminator The DMX terminator is BLUE simply a connector with a resistor about 1200 COHMD connected Es across pins 2 and 3 of the Canon plug please see the picture ie in the right It can prevent the noise and reflection caused by DMX 512 signal during transmission cmo a OPOLTOIJOIPJOIOINIoF cIc ye DID DmIoJjosfojojyojojo pr N po i IO l0 Oo IM o ex 7mm B H wo FN am He 3 ey le 2 c c 0 n ct o O Fh 5 h NY Y WIN TN O1 O1 C1 O1 O1 C1 zy 5 PROG Program INFO Information Illustrations ATOT RUN t d EE a O ATO5 RUN dr ATSP 0 255 5 usu 99 HST RUN s a o a e e o ON JRUN cx 0 Do 0 0 a CHS1 E Chase 1 Scene 1 B BLUE W WHITE AMBER UV Ultra Violet HUT IME AIT R 0 G 0 0 255 moe SC20 Scene 20 a Chase 5 SOFT Software version LEDs X X UJ X X gt x Pes px gt lt Ix e3 X a c POW lios 80 50 Power reduction ee ol da YES NO YES NO t
4. EV LIGHT e IEEE ande IAN Id mm i 0 FECHNICKL PARANIETER seiner indani errata eee iae T WGHTINGINSTALLATION eo terse ENEE 4 4 POWER SUPPLY CONTROL SIGNAL CONNECTIONS rennen 4 EV S 1 55 5 OPERATION MENU irienna eane sateen Sp Ebr ru yXR RE YPF MEE ira D nR 25 Ed BUTTON CORE RATION ssmszrirmensrsSsceuussss nere vUFI Se nsra Sj rani EEEREN sia ego ita enr a E JDNMBCADDBESS CODE SETTING mik eastten rase Intt ohsnbstaetsn vss sanaaa desunt 7 B ATACO ETTING oare ESEA A SA COLORCASTCALBRATION SETTING tutis tansan Ip ERr Bay 55 CHANNELMODESETTING Ssemases isesvensecessenszssnesdonseanexseensmentaadenaiceasessanseeeet oF e6 DIMITING RIOD SETTING wecesece sts videancdsstesestenscnerserersnceseteanctandcanaiasieersaveosney 7 e DEPAY Re Fe 5 8 RUN THEAUTO RUN AUTO PROGRAMMING PROGRAM eee E Eg EDIT AUTO lt PROGRAIMIMING BROGRAIVsssusmagdeedetststsbaeeseu eaedem oua g 5 10 CHECK THE LIGHTING INFORMATION sicteteclvecuse certs Guns e usasu sin oco aoa su g cii TIOHTING SETTING PARAMETER RESET wsetganetstdstegedatmesstye EU vet Ut psu g 5 12 PROG AUTO PROGRAMMING PARAMETER RESET eette lt lt EGS TOOBTINIG FR Se Wve segeretescy erences gence EEEN E E REENE ENEE A _Q 5 14 LIGHTING PARAMETER DOWNLOADING EACH OTHER nn 8 Gene MANIIENANCE tsscettssohau uie naanin ra ex opa Ape nn OEIL teres 9 2 TROUBLESHOOTING Ric i E aonsea eae b E Ru S NE MER UU ER tv Cep Mapa UP AE en Sa Uo aepo NN SNP ced E De S A 9 B DO
5. MDXPROTOCO LssssdisudmemedpiisaRe reis pubic ndtreo tan iap a opuv i eaa 10 ACCESSORIES These items are packed together with the lighting please check USER MANUAL Please read it carefully l SAFETY GUIDELINE Please keep this manual ina safe place for further reference Please make sure they also have this user manual if you sell this lighting to other users Every unit is packed properly by the manufacturer Please operate this lighting according to the user manual Any damage caused by improper use will not be assumed by the manufacturer When receiving the lighting please dispose the carton check and inspect there is any damage or not Should there be any damage caused by transportation do not use the lighting and consult your dealer or the manufacturer This lighting can be used indoors IP20 The lighting is only intended for installation and operation by qualified personnel 9 Do not mountthe lighting directly onto inflammable surface Ensure power supply voltage correspond to device requirements before running e It is essential that each lighting is correctly earthed and that electrical installation conforms to all relevant standards When the lighting is hanged to a high place please use a safety cord provided to pass through the lighting handles as a secondary safety fixing for safety seasons For details refer to LIGHTING INSTALLATION section Avoid direct exposur
6. e Amber UV 0 proportional Light Blue Blue full White full Red Green Amber UV 0 step White full Blue down Red Green Amber UV 0 proportional Light Amber White full Amber full Red Green Blue UV 0 step White gt down Amber full Red Green Blue UV 0 proportional Amaranth pink Amber full Ultra Violet full Green Blue White O step Ultra Violet full Amber down Red Green Blue White 0 proportional Amaranth Red full UV full Green Blue White Amber O0 step Red full UV down Green Blue White Amber 0 proportional Bright mauve Red full Amber full UV full Green White Amber 0 step Red gt down Amber full UV full Green Blue White 0 proportional Half White Red half Green half Blue half White half Amber half UV half step Use menu setting dimmer mode Dimmer off Dimmer 1 Dimmer 2 Dimmer 3 Dimmer 4 Use menu setting dimmer mode Reset Cat least 5S 10 EV LIGHT GUANGZHOU CO LTD ADD EV INDUSTRIAL PARK 68 CHUANGYE ROAD TAIPING DEVELOPMENT ZONE GUANGZHOU TEL 486 20 37929678 FAX 186 20 37929298 WEBSITE Http www evlightpro com
7. e to the light from the lamp specially for people with epilepsy The light is harmful to eyes Do not project the beam onto inflammable surfaces The minimum distance between the lighting and irradiated object should be 1 m Exterior surface temperature of the lighting will be 65 C when working please do not touch it with bare hands To prevent electric shocking please do not touch the power cord when the lighting is running Never let the power cord mix with other cables TheLED lens should be changed if deeply scratched or cracked There is no user serviceable parts inside the lighting Before using the device please check whether the covers or housing are well installed or not and whether the screws are installed firmly or not Do not open the housing and never operate the lighting with the covers removed Always disconnect a lighting from the power supply when the device is not in use or before cleaning it or before attempting any maintenance work Electrical connection must only be carried out by qualified personnel Please use the original packing material for second transportation If you have any questions or suggestions please do not hesitate to consult your dealer or our factory 2 TECHNICAL PARAMETER Input Voltage AC100V AC240V 50 60HZ Power Consumption 60W Lamp Specifications 5 pcs six in one RGBWA UV high efficiency 12W LED rated life 50000 hours Len
8. ghtings for series connection pattern when using 220V AC it can t exceed 6 PCS lightings for series comection pattern when using 110V AC SAFETY CORD POWER OUT POWER IN PICTURE ONE PICTURE TWO SUPPORT The lighting can be hanged at the high place with using the lamp hooks as showed in picture one Use the safety cord provided to pass through the handles and hang it as a second safety fixing evel 2 Level 3 Thelighting also can be used on the ground as showed in picture 2 Address STAT 255 EE Static control 255 PO 255 a Note 255 EE Ensure support loading ability at least 10 times more than product weight and e also make sure the lighting is installed steadily 255 CAL RED gt The lighting must be installed by the qualified personnel Please install it Calibration GREEN 255 at the place where no one goes through BLUE 255 W WHITE 2255 AMBER 255 4 POWER SUPPLY CONTROL SIGNAL CONNECTIONS V Ultra Violet 0 255 S NO CHMD Make the XLR signal line connect with the lighting one port connects with the output port of Channel mode lighting another one connects with the input port of another lighting DIM Dimming mode Due to the output and input of the lighting keep connecting all the time so the DMX circuit still can be keep connecting when the power of certain unit occurs turn off XLR signal line only can be used
9. hting is idle for a long time damp dust can cause greater accumulation of dirt on its cover or housing So it should be cleaned to maintain an optimum light output and at the same time to prevent it from corrupted by dust and acid gas Cleaning frequency depends on the lighting operation frequency and the environment in which the fixture operates Soft cloth and typical glass cleaning products should be used for cleaning It is recommended to clean projector at least once every 20 days Do not use any organic solvent e g alcohol to clean housing of the apparatus T TROUBLESHOOTING PROBLEM REASON AND ACTION The lighting can t be started normally Out of console s control The beam appears dim the brightness declines obviously Check the power connection is correct or not Please detect the voltage Power supply is damaged or incorrect connected Calla qualified personnel to fix it Connection of control board is not correct Call a qualified personnel to fix it Please check the DMX connector and the power connection is connected correctly or not It means having signal if it shows twinkling of the decimal point which in the lower right corner of the screen when exiting the screen saver Please check the DMX address setting of lighting is correct or not Check CHMD setting is correct or not Please check whether the DMX line is near to the high voltage wire or not In that case it will damage or interfe
10. re the DMX electric circuit Check whether the CAL is started or not and the set value is too small Check whether the POW is in over temperature protection situation or not if yes please take measures for ventilation 8 DMX PROTOCOL Function Dim all Red Green Blue White Amber Ultra Violet No strobe Strobe slow fast Random Strobe slow gt fast Electronic Squarewave slow gt fast No effect WHITE 1 3200K WHITE 2 3400K WHITE 3 4200K WHITE 4 4900K WHITE 5 5600K WHITE 6 5900K WHITE 7 6500K WHITE 8 7200K WHITE 9 8000K WHITE 10 8500K ATO1 R G B W A UV RG RB RW RA RUV GB GW GA GUV BW BA BUV WA W UV AUV RGB RGW RGA RGUV GBW GBA GBUV BWA BWUV WAUV RGBW RGBA RGBUV GBWA GBWUV RGBWA GBWAUV RGBWAUV ATO2 R t RV Gt GY Bt BY Wt Wy At AtY UVt UV4 ATO3 R TGTt RVGY RtTBt RIYBY RtTWt RIVWY RTAT RIA Tok PUY Tok GUY Gey ip seu oepwi Gbw GrAy eGd A GtTUVt GYJUVY BtWt BIWY BtAt BYAY BtUVt By UV L WTAT WIAL WtUVt W4UVL ATUV f ALUVI ATOA RT 6G Bw tA th UV I RG Baw AY Uvi4t ATOS Rainbow effect B BG t BG B 4 G G GR t GR GI R R RB SRB RVB CHASE1 CHASE2 CHASE3 CHASE4 CHASES Reserved 0 255 S Auto speed fast gt slow when AUTO 1 AUTO 5 effective Virtual colour wheel No effect Blue Blue full Red Green White Amber UV 0 step Blue full Green up Red Whit
11. rmal conditions but 8096 or 5096 output in over temperature protection situation 5 11 LIGHTING SETTING PARAMETER RESET 1 Press the ENTER button in ST L menu then enter to the lighting setting parameter reset 2 Press the UP DOWN button to select YES 3 Press the ENTER button to escape and save 5 12 PROG AUTO PROGRAMMING PARAMETER RESET 1 Press the ENTER button in PR L menu then enter to the PROG auto programming parameter reset 2 Press the UP DOWN button to select YES 3 Press the ENTER button to escape and save 5 13 LIGHTING RESET 1 Press the ENTER button in REST menu then enter to the lighting reset 2 Press the UP DOWN button to select YES 3 Press the ENTER button for confirmation of lighting reset 5 14 LIGHTING PARAMETER DOWNLOADING EACH OTHER 1 Press the ENTER button in SEND menu then enter to sending parameter to other lightings 2 Press the UP DOWN button to select YES 3 Press the ENTER button to confirm sending 8 Illustrations D Must disconnect the connection of projector and console before sending the parameter 2 The information of ADDR CAL can t be sent can t be downloaded each other 3 There will be an automatic reset of the other projectors after receiving parameter correctly 6 MAINTENANCE To prolong the life of lighting it is very important to do the maintenance work The environment is hash outdoors or if the lig
12. s Angle 25 optional 15 30 35 Color RGBWA UV linear color mixing Color Temperature color cast calibration setting color temperature output inside device Dimmer 0 100 linearly dimming 5 types dimmer modes smooth dimming flicker free Shutter independent electronic strobe Control Mode Standard DMX512 3 pin interfaces 4 channel modes 6 7 9 12 CH Master slave mode no need to set up the master and slave manually will receive the main engine data automatically 5 auto running modes rainbow channel and rainbow effect Other Functions Self programming function 5 chases each chase has 20 scenes fade function Lighting setting data self programming data can be downloaded each other Temperature Control Protection both of lamp holder and base have temperature control protection Waterproof Grade IP20 Work Environment Temperature 20 C 40 C Net Weight 2 3Kg DIMENSION 236 5 9 3 192 22 7 6 34 LIGHTING INSTALLATION e The transmission speed of DMX 512 signal is very quick It will affect the signal transmission if any damage of the signal line the weld is not firm or bad connection etc MOUNTING HOLE FOR LAMP HOOK l l l l l l The connector with 3 pins XLR is more universal than the one with 5 pins XLR 3 pins XLR PIN 1 GND PIN 2 signal PIN 3 signal 5 pins XLR PIN 1 GND PIN2 signal PIN3 signal PINA PIN5 UNUSED There can t be more than 12 PCS of li
13. z lt ae o d TETTE TERT VN tn eim m tz V O1 O1 When the menu is set as the information of position the projector will be set automatically to be the main engine and then send data to external Other projectors can receive these data and run synchronously with the main engine It still be run according to these setting parameter even if power reconnection after power off When setting YES in ST L menu The parameter will bereset to be the factory default value as which with underline of above chart 5 1 BUTTON OPERATION 1 MENU Toreturn to the previous menu 2 ENTER Enter to the next menu or save 3 UP Menu selection or increasing the parameter p 4 DOWN Menu selection or decreasing the parameter J T C J J ra 5 2 DMX ADDRESS CODE SETTING MENU UP DOWN ENTER 1 Pressthe ENTER buttonin ADDR menu then enter to the DMX address code setting 2 Press the UP DOWN button to select 1 512 numerical value 3 Press the ENTER button to escape and save 5 3 STATIC SETTING 1 Press the ENTER button in STAT menu then enter to the static setting 2 Press the UP DOWN button to select IER G B Ew A uv and SHUT 3 Press the UP DOWN button to set up the 0 255 numerical value 4 Press the ENTER button to escape and save 5 4 COLOR CAST CALIBRATION SETTING 1 Press the ENTER button in CAL menu then enter to the color cast calibration setting 2 Press the
Download Pdf Manuals
Related Search
Related Contents
Brother 882-D00 Sewing Machine User Manual Synway TEJ Series User Manual The CYBER 845: First Month`s Use Imation Defender F100 1GB EVT 4000e service manual vie quotidienne et droits sociaux des adultes en Mode d`emploi KVIE 2529/A MANUAL DE EXPLICACIONES Honda WB20XT, WB30XT Copyright © All rights reserved.
Failed to retrieve file