Garage Door Controller
Contents
1. AEOTEC BY AEON LABS ENS Garage Door Controller GEN View the expanded manual http aeotec com support 00 7 0 0 09 00 0 o 0 o 0 0 0 9 0 09 0 09 0 20990092 009 09 8 000 0000 D Aeotec by Aeon Labs Garage Door Controller Aeon Labs Garage Door Controller is a smart and wireless Garage Door Control system you can control the garage door to open close or stop moving via wireless signal on your gateway client or phone application You can also control it by using the external switch when your controller or mobile phone is not on hand Its 105dB speaker system will play alarm sounds and at the same time the indicator of the Garage Door Controller s Alarm LED will turn on in which will let you know that the garage door will start to open or close The Garage Door Controller allows you to configure different alarm sounds to indicate the door s action Each action alarm sound can be customized To change or update new alarm sounds for the Garage Door Controller connect the Garage Door Controller to your PC host with a USB cable and download your sound files to the flash memory 16 MB of the Garage Door Controller You can also manually switch the alarm sound To do this short press the button or button button on the Garage Door Controller which will switch the alarm sound to the next sound Press and hold the button or button to decreas2. Press any button on your Minimote to take it out of removal mode Reset your Garage Door Controller If your primary controller is missing or inoperable you may wish to reset your Garage Door Controller to its default factory settings To do this press and hold the Z Wave Button for 20 seconds and then release it Your Garage Door Controller will now be reset to its original settings and the Network LED will be solid for 2 seconds and then start slow blinking to confirm a success Technical specifications Model Number ZW062 Power Supply 5V DC Adapter for Garage Door Controller CR2 Lithium battery 3V 800mA for Sensor Max Alarm Power 2W Max Standby Power 1W Max Volume 105cB Operating Temperature 10 C to 45 C Storage Temperature 20 C to 70 C Supported Audio Formats MP3 and WMV within the bit rate of 320 Kbps Operating Distance Up to 980 feet 300 metres outdoors Warranty Aeon Labs warrants to the original purchaser of Products that for the Warranty Period as defined below the Products will be free from material defects in materials and workmanship The foregoing warranty is subject to the proper installation operation and maintenance of the Products in accordance with installation instructions and the operating manual supplied to Customer Warranty claims must be made by Customer in writing within thirty 30 days of the manifestation of a problem Aeon Labs sole obligation under the foregoing wa
3. Z Wave network its Network LED will no longer blink If the linking was unsuccessful and the Network LED continues to blink repeat the steps above 6 Press any button on your Minimote to take it out of inclusion mode With your Garage Door Controller now working as a part of your smart home you ll be able to configure it from your home control software or phone application Please refer to your software s user guide for precise instructions on configuring Garage Door Controller to your needs The speaker system is 105dB and you can reduce its volume via long pressing the Button or increase the volume via long pressing the Button When the Button or Button is pressed the default Garage Door Controller alarm sound will be triggered To switch to the next alarm sound short press the Button or Button Physically install your Garage Door Controller The Garage Door Controller must be installed in your home and near the garage door It cannot be installed outdoors in elements such as rain and snow 1 Utilize the provided 20mm screws to affix it to the desired surface 2 Connect the 2 Switch cables to the Switch Connector 1 and 2 on the Garage Door Controller and then use the Fast Wiring Clip to connect the 2 Switch Cables to the Motor Switch Cables see the figure below Motor Switch Motor Switch Cable Fast Wiring Clip P 4 Switch Cable 2 Fast Wiring Clip
4. ov Switch Cable 1 X lt SS Motor Switch Cable Switch Cable Oo Note The Fast Wiring Clip needs to be used with pliers When the Switch Cable and the Motor Switch Cable have been connected by Fast Wiring Clip you will need to use the pliers to clamp the Fast Wiring Clip see the figure above 3 Now lock the Garage Door Controller to the Back Mount Plate by twisting the Garage Door Controller Extemal Switch of Motor Garage Door Controller 0 90 29509000 059 90 0 000900000000 00 9 000000000 0000000 0 000070 0000900 0 I 000000000000 0000000000000000 1900900900509 00000 o 0000000020000000 0 0 0 g0 0000000092090 90 009000 TRN 0200 00 00000000020 j0 00000090000 0 E sees 000 5V DC Adapter LL Switch cabel 1 0000020 00950000 o eNO NISSAN 00900 LOO reo eX ey 000 099000 80000000000000 g 0000000000 0000000000000 99 90 070900000 0 990A HOG G O0009 990 9090009 8P 000 Switch cabel 2 Installing the Sensor on your garage door 1 Press and hold the Latch Button to unlock the sensor mounting plate Press and hold the Latch Button 2 Pull out the insulating sheet then you will see the Sensor LED blink once to indicate it has been powered on Insulating sheet 3 Affix your sensor mounting plate to the garage door The sensor mount pl
5. UCTS WHETHER BASED ON NEGLIGENCE STRICT LIABILITY BREACH OF WARRANTY BREACH OF AGREEMENT OR EQUITABLE PRINCIPLES IS EXPRESSLY LIMITED TO AT AEON LABS OPTION REPLACEMENT OF OR REPAYMENT OF THE PURCHASE PRICE FOR THAT PORTION OF PRODUCTS WITH RESPECT TO WHICH DAMAGES ARE CLAIMED ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY 30 DAYS FROM AEON LABS S DELIVERY OR THE DATE FIXED FOR DELIVERY IN THE EVENT OF NONDELIVERY THE INDEMNITY AND WARRANTY IN ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER INDEMNITIES OR WARRANTIES WHETHER EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE FCC NOTICE for USA THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT SUCH MODIFICATIONS COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT STORE INDOORS WHEN NOT IN USE SUITABLE FOR DRY LOCATIONS DO NOT IMMERSE IN WATER NOT FOR USE WHERE DIRECTLY EXPOSED TO WATER This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B
6. alibrate the Sensor once For detailed calibration steps please refer to the Configuration Parameter 34 in the engineering spec document of Garage Door Controller Advanced functions Removing your Garage Door Controller from a Z Wave network The following instructions will tell you how to remove your Garage Door Controller from your Z Wave network via an Aeotec by Aeon Labs Z Stick or Minimote controller If you are using another Z Wave controller as your main controller please refer to their respective manual on how remove devices from your network If you re using a Z Stick 1 If your Z Stick is plugged into a gateway or a computer unplug it 2 Take your Z Stick to your Garage Door Controller 3 Press the Action Button on your Z Stick 4 Press the Z Wave Button on your Garage Door Controller 5 If your Garage Door Controller has been successfully removed from your network its Network LED will blink If the removal was unsuccessful the Network LED will not blink 6 Press the Action Button on the Z Stick to take it out of removal mode If you re using a Minimote Remove 1 Take your Minimote to your Garage Door Controller 2 Press the Remove Button on your Minimote 3 Press the Z Wave Button on your Garage Door Controller 4 lf your Garage Door Controller has been successfully removed from your network its Network LED will blink If the removal was unsuccessful the Network LED will not blink 5
7. ate should be installed on the top of the garage door on the left middle or right side Now affix your sensor mounting plate to the surface Your mounting plate can be affixed using screws or double sided tape If you are using screws attach the mounting plate to the respective surface using the two 20mm screws provided PEN ame HIR Emme H If you are using double sided tape wipe the two surfaces clean of any oil or dust with a damp towel When the surface has completely dried peel one side of the tape back and attach it to the corresponding section on the rear side of the mounting plate 4 Lock your Sensor on the mounting plate Press and hold the Latch Button and then push the Sensor into the mounting plate le The Latch Button should face the up of direction After completing all installation steps you may need to test your Garage Door Controller to see if it has been successfully installed You can implement this via short pressing the Switch Button on the Garage Door Controller When you press the Switch Button you will see the alarm LED blink and ring the alarm sound After about 5 seconds the garage door will move to a full open or closed position If you press the Switch Button again the garage door will immediately stop moving If not please check or repeat the steps above Note If you have confirmed the installation is successful you need to c
8. digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consul the dealer or an experienced radio TV technician for help Warning Do not dispose of electrical appliances as unsorted municipal waste use separate collection facilities Contact your local government for information regarding the collection systems available Certifications regional Z Wave and Z Wave Plus are registered trademarks pe of Sigma Designs and its ip subsidiaries in the United A States and other countries Version 501005600002 AA www aeotec com AEOTEC BY AEON LABS
9. e or increase the volume The Garage Door Controller is also a security Z Wave device and supports the Over The Air OTA feature for the product s firmware upgrade Familiarize yourself with your Garage Door Controller Package contents Garage Door Controller Sensor 5V DC Adapter USB Cable Switch Cable x2 Screw x6 Back Mount Plate Fast Wiring Clip x2 Double Sided tape OONDAARWNDY Button Speaker System Button Z Wave Button Alarm LED Network LED Switch Button Latch Button Sensor LED Security Temper Switch Switch Connector 1 Switch Connector 2 USB Connector 5V DC Adapter Port Port Quick start Power on your Garage Door Controller Step1 Unlock the Back Mount Plate of Garage Door Controller by twisting the Back Mount Plate and separating the two parts of your Garage Door Controller 000049 00000 000002000000 430000090090050000 0000000000000000 0 0 4 000000002000900000 0 0 0 0 00 000000020002009000 007 0 0 0000000000300020009900 00 00 0 000 Ra 90860 00 00 ONORA Re Step2 Power your Garage Door Controller by connecting the 5V DC Adapter to the input Z Wave Button Network LED aime 5V DC Adapter Now that your Garage Door Controller is powered on you will see the Network LED blinking slowly While the Network LED is blinking this indicates tha
10. olders directors officers employees contractors agents and other representatives harmless from all demands claims actions causes of action proceedings suits assessments losses damages liabilities settlements judgments fines penalties interest costs and expenses including fees and disbursements of counsel of every kind i based upon personal injury or death or injury to property to the extent any of the foregoing is proximately caused either by a defective product including strict liability in tort or by the negligent or willful acts or omissions of Customer or its officers employees subcontractors or agents and or ii arising from or relating to any actual or alleged infringement or misappropriation of any patent trademark mask work copyright trade secret or any actual or alleged violation of any other intellectual property rights arising from or in connection with the products except to the extent that such infringement exists as a result of Aeon Labs manufacturing processes IN NO EVENT SHALL AEON LABS BE LIABLE FOR ANY INDIRECT INCIDENTAL PUNITIVE SPECIAL OR CONSEQUENTIAL DAMAGES OR DAMAGES FOR LOSS OF PROFITS REVENUE OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY WHETHER IN AN ACTION IN CONTRACT OR TORT OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES AEON LABS LIABILITY AND CUSTOMER S EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF THE PROD
11. rranty is at Aeon Labs option to repair replace or correct any such defect that was present at the time of delivery or to remove the Products and to refund the purchase price to Customer The Warranty Period begins on the date the Products is delivered and continues for 12 months Any repairs under this warranty must be conducted by an authorized Aeon Labs service representative and under Aeon Labs RMA policy Any repairs conducted by unauthorized persons shall void this warranty Excluded from the warranty are problems due to accidents acts of God civil or military authority civil disturbance war strikes fires other catastrophes misuse misapplication storage damage negligence electrical power problems or modification to the Products or its components Aeon Labs does not authorize any person or party to assume or create for it any other obligation or liability in connection with the Products except as set forth herein Aeon Labs will pass on to Customer all manufacturers Material warranties to the extent that they are transferable but will not independently warrant any Material Customer must prepay shipping and transportation charges for returned Products and insure the shipment or accept the risk of loss or damage during such shipment and transportation Aeon Labs will ship the repaired or replacement products to Customer freight prepaid Customer shall indemnify defend and hold Aeon Labs and Aeon Labs affiliates shareh
12. t the Garage Door Controller is ready to be included into a Z Wave network Add include link your Garage Door Controller to a Z Wave network The following instructions will tell you how to link your Garage Door Controller to your Z Wave network via an Aeotec by Aeon Labs Z Stick or Minimote controller If you are using another Z Wave controller as your main controller please refer to their respective manual on how add new devices to your network If you re using a Z Stick 1 Connect 5V DC Adapter to the Garage Door Controller Its Network LED will begin to blink 2 If your Z Stick is plugged into a gateway or a computer unplug it 3 Take your Z Stick to your Garage Door Controller 4 Press the Action Button on your Z Stick 5 Press the Z Wave Button on the Garage Door Controller 6 If Garage Door Controller has been successfully linked to your Z Wave network its Network LED will no longer blink If the linking was unsuccessful and the Network LED continues to blink repeat the steps above 7 Press the Action Button on the Z Stick to take it out of inclusion mode If you re using a Minimote Include 1 Connect 5V DC Adapter to the Garage Door Controller Its Network LED will begin to blink 2 Take your Minimote to your Garage Door Controller 3 Press the Include button on your Minimote 4 Press the Z wave Button on your Garage Door Controller 5 If Garage Door Controller has been successfully linked to your
Download Pdf Manuals
Related Search