Manual : Wireless Model WTSL-SN-1
Contents
1. HOWTO LEARN IN THE ALARM CONTROL UNITTO A WIRELESS NETWORK 1 Using a ballpoint pen briefly push and release the learn button on the back of the control unit The red LED next to the learn button will flash briefly then light up for approximately 5 seconds During these 5 seconds you need to briefly press the test button on an alarm already in the network to wirelessly interlink the two The alarm will give an audible sound consisting of two cycles of three loud beeps The red LED on the back of the control unit will flash to indicate that it has been learned in successfully If the test button is not pressed quickly enough the learn in process will fail If this happens repeat the process 4 To complete the installation simply slide the control unit onto the bracket until it clicks into place The control unit is now part of the whole network The method above assumes you have already installed your alarm network prior to installing your Alarm Control Unit If you want to install your Alarm Control Unit first you can learn your smoke heat and CO alarm into it by following the instructions in your alarm manual using the Alarm Control Unit as alarm 1 and holding the Test button of the Alarm Control Unit for at least 2 seconds MAKING THE ALARM CONTROL UNIT TAMPER PROOF Do not complete this action until you have wirelessly interlinked all of your alarms The Alarm2. Please contact Technical This indicates an internal Support on 0800 171 2009 or fatal radio failure technicalsupport sonasafety com Flashing rapidly 18 Either the carbon monoxide indicator or the smoke heat indicator is flashing every 10 seconds This indicates that one of the alarms has previously been activated Please refer to the Locate section of this manual Either the carbon monoxide indicator or the smoke heat indicator is flashing Triple flashing every second An alarm on the network has lost communication with the Alarm Control Unit Please refer to Identifying an Alarm in the Network which has Lost Communication with the Alarm Control Unit Either the carbon monoxide indicator or the smoke heat indicator is flashing Double flashing every second An alarm on the network has developed a fault Please refer to Identifying a Faulty Alarm in the Network 19 TROUBLESHOOTING Indication No lights come on when press any of the buttons on the Alarm Control Unit Nothing will happen if you are pressing the Locate button when there s no alarm or fault condition This may indicate that the control unit has not been successfully activated see section Activating the Alarm Control Unit When pressing the test button nothing is happening This indicates that the control unit has not been successfully activated see sect
3. Control Unit is provided with an anti tamper feature ensuring where needed it cannot be removed from the wall To make use of this feature you will need to tap out the two blanking plates on the top right hand side of the bracket using a small screwdriver being careful to support the bracket fully whilst doing so Once the rest of the installation is complete and the control unit is fixed to the bracket it can only be removed using the following method Insert a small screwdriver into the hole on the top right hand corner of the control unit until it stops this will disengage the lock then gently ease the control unit up to release it from the USER GUIDE TESTING THE ALARM SYSTEM Press the Test Silence s button to confirm that the control unit is operating properly This will instigate a three minute test All networked alarms should sound To stop the test earlier than 3 minutes simply press the Test Silence tst button again This test should be performed on a weekly basis PRODUCT FUNCTIONALITY Function Description Test Silence button Test button This allows you to test all wirelessly interlinked alarms from one centralised location Silence button This will silence all wirelessly interlinked smoke and heat alarms and reduce the system sensitivity for up to 10 minutes Locate button This will silence all wirelessly interlinked alarms
4. except the initiating alarm which has sensed carbon monoxide smoke Smoke heat alarm indicator This indicates that a smoke heat alarm has been activated Carbon monoxide indicator This indicates that a carbon monoxide alarm has been activated Fault indicator This indicates a fault with the control unit or one of the alarms within the network 13 LOCATE BUTTON If the alarms are sounding and an alarm indicator is flashing but there s no obvious hazard pressing the Locate button Q will silence all wirelessly interlinked alarms except for the initiating alarm which has sensed smoke heat or carbon monoxide After two minutes the system will return to normal operation and the alarms will continue to sound if smoke heat or carbon monoxide is still present To make locating the alarm easier the control unit can be removed from it s bracket and carried around the property providing the tamper proof function has not been engaged allowing you to press the Locate or Test button whilst moving from room to room SILENCE BUTTON If the alarms are sounding and the smoke heat alarm indicator is flashing but there s no obvious hazard pressing the Silence button will silence all wirelessly interlinked alarms and reduce the System sensitivity for up to 10 minutes However if excessive smoke is sensed the silence function will be overridden The indicator will continue to flash unless the smoke disappear
5. Sonn WTSL SN 1 Alarm Control Unit with Wi Safe 2 Installation and User Guide Search vin Tube sona control unit install For use with Wi Safe 2 Smoke Heat and Carbon Monoxide Alarms PLEASE READ THIS GUIDE IN FULL BEFORE USING YOUR WTSL SN 1 ALARM CONTROL UNIT This user guide is also available in large text and other formats Please call 0800 171 2009 for further information Battery powered Alarm Control Unit with Test Silence Locate function Non replaceable 3V DC battery W2 module contained within product independently tested to RF standard ETSI EN 300 220 2 V2 3 2 2010 02 by TRaC Global Ltd Email technicalsupport sonasafety com Web www sonasafety com Technical Support Line 0800 171 2009 ce x o A Sprue Brand Sprue Safety Products Ltd Vanguard Centre Coventry CV4 7EZ UK 2 GN3019R2 INSTALLATION GUIDE Features l l s Positioning Installation 2 dx ERE Wireless Interlink Making the Alarm Control Unit TamperProof Ln USER GUIDE Testing the Alarm System 12 Product Functionality 13 When an Alarm Sounds 17 LED Indicators 18 Troubleshooting 20 Maintenance 21 Disposal ae 86 ba ek ee 22 Watraltyzu s odes e ERR be 23 INSTALLATION GUIDE FEATURES Wi Safe 2 technology enabling wireless interlinking between other Wi Safe 2 products Test Silence 7Est sx button al
6. fly push and release and then push and hold the learn in button The red LED will remain illuminated during this process When the red LED goes out release the button it will then flash twice followed by three further flashes to illustrate that the alarm has successfully been un learnt from the network 2a Once the faulty unit has been un learnt the Alarm Control Unit will continue to flash for up to 24 hours After which the flash pattern will change to a triple flash at this point follow the process described in 2a Deleting a Faulty Alarm from the Alarm Control Unit s Memory Identifying an Alarm in the Network which has Lost Communication with the Alarm Control Unit If the amber fault LED is triple flashing every second this shows that an alarm on the network has lost communication with the Alarm Control Unit To identify the alarm in question press the TEST button on the Alarm Control Unit All alarms in the network will sound a test pattern except the alarm which has lost communication If this fault cannot be resolved you will need to delete the alarm from the Alarm Control Unit s memory see 2a below Deleting a Faulty Alarm from the Alarm Control Unit s Memory To delete the alarm from the Alarm Control Unit s memory simply press and hold the Locate button for 5 seconds The Alarm Control Unit will stop flashing and the faulty alarm will be deleted from the memory It will take the Alarm Control Unit 2 minutes to reco
7. ion Activating the Alarm Control Unit Unable to remove the control unit from its bracket You need to disengage the locking pins Refer to the Making the Alarm Control UnitTamper proof section 20 MAINTENANCE This Alarm Control Unit will act as a remote interface between the alarms in your home when maintained properly To ensure the reliability of the control unit Keep the control unit free from dust by gently vacuuming the case with a soft brush attachment every 3 months Never use cleaning solutions on the control unit Simply wipe with a damp cloth Do not paint the control unit Do not spray aerosols on or near the control unit Do not use any solvent based products near the control unit Do not attempt to repair the control unit Do not attempt to change the battery Do not remove any screws or open the main casing of the control unit Any attempt to do so may cause malfunction and will invalidate the warranty 21 DISPOSAL Waste electrical products should not be disposed of with your other household waste The Alarm Control Unit is ideally suited for disposal within the waste electronic and electrical equipment WEEE recycling scheme Please recycle where facilities exist Check with your local authority retailer or contact ourTechnical Support team for recycling disposal advice as regional variations apply WARNING Do not burn or dispose of in fire WARNING If your Alarm C
8. lowing you to regularly test all wirelessly interlinked alarms on a network Pressing the silence button will reduce the sensitivity of alarms for up to 10 minutes unless carbon monoxide has been detected in which case you can use the Locate function below to find the source alarm Locate button Q allowing you to silence all alarms but the initiating alarm during an alarm condition During a fault condition this feature will allow you to locate the alarm in fault in a similar way e 5 year warranty Fault indicator Smoke Heat alarm indicator alarm indicator Locate button Test Silence button Alarm Control Unit emma POSITIONING This Alarm Control Unit is suitable for use in domestic premises only It should be installed at an accessible point on the wall in a location where it will not be accidentally operated or knocked The Alarm Control Unit should be installed at a distance of approximately 1 4m from the floor lower if required so that it is fully accessible INSTALLATION e Ensure this Alarm Control Unit is installed by a competent person who feels able to install it according to the instructions e Read all installation instructions prior to installing this product WARNING To prevent injury this Alarm Control Unit must be securely attached to the wall in accordance with the installation instructions To mount the bracket onto a wall Please ensure tha
9. nfigure its memory During this period the Test and Locate functions will be disabled WHEN AN ALARM SOUNDS Never ignore an alarm If there is a fire evacuate the premises and call the fire brigade If the source of the alarm is not immediately apparent check which indicator is flashing on the control unit If the CO indicator is flashing e Keep calm and open the doors and windows to ventilate the property e Stop using all fuel burning appliances and ensure if possible that they are turned off e Evacuate the property leaving the doors and windows open e Ring your gas or other fuel supplier on their emergency number keep the number in a prominent place LED INDICATORS Red Smoke i Red CO LED Heat LED Amber Fault LED Status Action required Please refer to the Wireless Flashing for 10 Flashing for 10 Flashing for 10 The Alarm Control Unit is Interlink section to learn ds ds ds s seconds every SeGORUSHevery See Onde every not part of a network in the control unit to the hour hour hour network Flashing rapidl Alarm A carbon Keep calm and open the ve end x monoxide leak has been doors and windows to y detected ventilate the property Flashing rapidly Alarm Smoke heat has Keep calm and evacuate the every second been detected property Low battery condition or the end of the product life The control unit should be replaced as soon as possible Flashing once every 5 seconds
10. ontrol Unit is dropped or damaged as a precaution it should be removed from the building and you should contact Technical Support on 0800 171 2009 or technicalsupport sonasafety com 22 WARRANTY Sprue Safety Products Ltd warrants to the original purchaser that the enclosed WTSLSN 1 Alarm Control Unit be free from defects in materials and workmanship under normal residential use and service for a period of five years from the date of purchase Provided it is returned with postage prepaid and proof of purchase date Sprue Safety Products Ltd hereby warrants that during the five year period commencing from the date of purchase Sprue Safety Products Ltd at its discretion agrees to replace the unit free of charge The warranty on any replacement WTSL SN 1 control unit will last for the remainder of the period of the original warranty in respect of the unit originally purchased that is from the date of original purchase and not from the date of receipt of the replacement product Sprue Safety Products Ltd reserves the right to offer an alternative product similar to that being replaced if the original model is no longer available or in stock This warranty applies to the original retail purchaser from the date of original retail purchase and is not transferable Proof of purchase is required This warranty does not cover damage resulting from accident misuse disassembly abuse or lack of reasonable care of the product or applications not in accordance
11. s Please Note An alarm cannot be silenced using the Alarm Control Unit if carbon monoxide has been detected however the Locate function will allow you to find out which of the CO alarms is the initiating alarm ALARM MEMORY If one of the alarm indicators is flashing every 10 seconds this indicates that a smoke alarm heat alarm or carbon monoxide alarm has previously been activated Pressing the Locate button Q will sound the source alarm so you can investigate this further The LED will continue to 14 flash for 10 minutes after the Locate button Q is pressed for the first time allowing you to press the button repeatedly until the source alarm is identified After 10 minutes the flashing LED s will clear fully compatible with the SONA Wi Safe 2 smoke heat and CO alarms FAULT DETECTION 1a Identifying a Faulty Alarm in the Network If the amber fault LED and a red alarm LED are flashing this indicates that an alarm on the network has developed a fault To identify the faulty alarm press the Locate button and the alarm in fault will sound an SOS sound pattern If the fault can t be rectified you must un learn it from the network see 1a below Removing a Faulty Alarm from the Network To remove a faulty alarm from the network you will need to perform a button press sequence consisting of a short press followed by a long press Using a ball point pen in the circular learn in hole in the back of the alarm brie
12. t you use the screws provided as they were chosen specifically for use with this product Drill holes into the wall and insert suitable wall plugs Screw the bracket in place ACTIVATING THE ALARM CONTROL UNIT The Alarm Control Unit has a sealed in non replaceable battery To activate the control unit remove the disabling clip Upon activating the control unit all three LED s should simultaneously flash twice to indicate that they are working Once the alarm is activated it is at this stage you will need to connect it into the wireless network before securing to the wall bracket WIRELESS INTERLINK The Alarm Control Unit is designed to be used as a remote interface between up to 50 products within the Wi Safe 2 product range The Alarm Control Unit can be used to test silence or locate any alarms on the Wi Safe 2 network It is not designed to communicate with wireless alarms from other ranges or manufacturers The control unit needs to be learned in or interlinked in order to communicate within the network Wi Safe2 enables wireless communication with any other product with Wi Safe 2 technology inside When one alarm detects smoke heat carbon monoxide the wireless module inside sends a wireless signal to all the connected alarms ensuring almost instantaneous reaction across the network CED 2 M MORELOS v IBEEHEEEHREREREREREERERHRIEI Wi Safe 2 enabled device Wireless Interlink 4 TZ QJ
13. with the user guide It does not cover events and conditions outside of Sprue Safety Products Ltd s control such as Acts of God fire severe weather etc It does not apply to retail stores service centres or any distributors or agents Sprue Safety Products Ltd will not recognise any changes to this warranty by third parties Sprue Safety Products Ltd shall not be liable for any incidental or consequential damages caused by the breach of any expressed or implied warranty Except to the extent prohibited by applicable law any implied warranty of merchantability or fitness for a particular purpose is limited in duration for five years This warranty does not affect your statutory rights Except for death or personal injury Sprue Safety Products Ltd shall not be liable for any loss of use damage cost or expense relating to this product or for any indirect or consequential loss damages or costs incurred by you or any other user of this product 23 Heat Alarm Smoke Alarm Wireless Wireless Non Wireless Non Wireless Carbon Monoxide Alarm Alarm Control Unit Wireless Wireless Wi Safe 2 Available on all wireless products
Download Pdf Manuals
Related Search