GC-1317D Internal-System, Operation, English
Contents
1. 3 Attach grounding clamp assembly P N 17440 00 to the slave pump Attach here 4 Securely attach Clamp P N 7749 00 to permanently grounded rod or pipe 7749 00 1 NA GROUNDING ROD OR PIPE 7750 04 ANWR Before turning on main air check all On Off Ball Valves making certain all Valves the Off position and set all regulators their position Turn knob counter clockwise for OFF or reduced pressure setting 5 Place the mixing element straight into the front gun housing refer to gun user manual 6 Place the retaining nut along with the spray tip and spray tip spacer onto the gun housing refer to spray gun user manual 7 Push the slide valve to the open position 8 Open the air valve p n 3165 on the solvent tank and adjust the solvent pressure to 90 PSI 6 2 bar Open the ball valve p n 18470 05 on the solvent tank Next open ball valve p n 23518 00 on the gun to verify that solvent will flow out of the front of the gun through the dispense tip then close the valve Do not exceed 20 PSI 1 4 bar on the material regulator until a steady material flow has been established Regulator Valve ad Ball valve 3165 Here 13193 00 13193 00 7 7749 00 7750 04 9654 00 5 TO SLAVE PUMP lt 20 GC 1317D Start Up b Once primed increase the resin PSI until a2. a034 1 101 2 a034 1 101 2 Z0 098 WH agy a034 IWLOL 2 66 8500 96 NY 00 92971 aod r 66 1700 96 aod v 66 1 00 96 017999 031512348 ASIMYAHLO 5531 5 10 v 66 1700 96 L ALO 10 92971 ANY ALO 00 92971 AGNIONI SWALI CIHOYLLYNN v 66 Z 00 96 SV 79 8 OL NHHL INO v 66 100 96 NGA S NILLI4 JO 103 SMOHS MIIA NGA 00 16861 XZ LIM HSLVSH SGMIONI TINI SE OL INDHOL 00 26861 XZ Sub Assembly Drawings 21460 00 Heater Conversion Kit Assembly GC 1317D 28 Sub Assembly Drawings 21460 00 Heater Conversion Kit Assembly 20195 25 PART OF HOSE ASSY TO GUN 20260 00 PART OF TANK ASSY BACK TO TANK D 156 04 FROM PUMP MAY BE SHIPPED DISASSEMBLED INLET Part Number Description Qty 500479 96 0037 96 0041 GC 1317D Maintenance Before performing any maintenance on this Dispense Gun Follow pressure relief procedures on page 19 See Indy and Formula gun manuals for daily maintenance and parts replacement procedures 1 Clean filter at resin pump When opening pump relief valve make sure all resin and air is evacuated from surge bottle Fluid Filter Assembly 2 Inspect and clean filter on pick up wand 1 GC 1317
3. Up Clear Tubing 1 4 in GC 1317D Clear Tubing 1 8 in Solvent Pot Catalyst Bottle 20260 00 Recirculation Hose tape together with green material hose Do Not insert the hoses in the material drum until the system has been flushed Clear Tubing 3 8 in GAM 268 01 Pick Up Kit 17 Set Up SSP 175 Safety Guard Kit 20188 16C 7734 06 SSP 177 Ny 20188 16C 7734 06 20188 16C 7734 06 7486 13 SSP 173 20188 16C 7734 06 7486 13 7734 06 55 172 8 20188 6 7734 06 SSP 176 4 5 174 7486 05 55 175 Part SSP 173 LEFT PUMP GUARD AN N 5 X N S N N S X N WS N N Ns 20188 16 REMOVE PROTECTIVE FILM FROM BOTH SIDES OF THE SAFETY GLASS AND ATTACH IT TO THE COVER USING HARDWARE P N S 20188 16C AND M SSP 178 20188 16 7734 06 GC 1317D Pressure Relief Procedure To relieve fluid and air pressures 1 Push down Yellow slide valve P N 21402 00 to bleed off air to system 2 Open P N 21228 00 on catalyst pump to recirculation position GC 1317D 19 Start Up The following assumes that all connections are tight System Start Up Instructions 1 Select a clean dry air supply 2 Attach a 3 8 or larger air hose to the Air Manifold Inlet Do not use quick disconnect fittings
4. changes at any time without notice This manual contains English GC 1317 Graco Headquarters Minneapolis International Offices Belgium China Japan Korea GRACO OHIO INC 8400 PORT JACKSON AVE NW NORTH CANTON OH 44720 Copyright 2008 Graco Ohio Inc is registered to ISO 9001 www graco com Revised 06 2010
5. desired SSP 160 01 spray pattern is achieved Ya Pull and rotate Pivot knob to disengage the catalyst drive arm c After all pressure adjustments have been completed a finial spray test should be made Spray a test shot sample clean piece of paper The shot should be approximately five feet in length You can now check desired gel times and uniformity of curing b Turn the slave pump yellow ball valve to the open position d Flush the gun thoroughly with solvent after use 11 Make sure that the resin pump recirculation valve is off and that the bypass hose is in back in the the drum Adjust the resin pump regulator to 20 PSI 1 4 bar the pump will start to slowly cycle Allow the pump to load the cycle rate should slow indicating the pump is primed Close the recirculation valve C Hand prime the pump until a steady stream of cat alyst flows back to the bottle d Close the ball valve Hand stroke the pump until it devel opes 300 400 PSI 21 28 bar If you are using the optional Formula gun set the trigger air regulator to 100 PSI 7 bar The trigger air IS NOT to exceed 100 PSI 7 bar Recirculation Valve Resin Pump Regulator 10 Trigger the Gun into a container until all the air is purged from the resin side of the system It may be necessary to Hand stroke the Catalyst Pump several times while the gun 15 triggered to positively deliver a steady stream of catalyst Let
6. not require any diluents GlasCraft strongly recommends that dilu ents not be used Diluants add to the possibility of con taminates entering the catalyst system Never dilute MEKP with acetone or any solvent since this can pro duce an extremely shock sensitive compound which can explode Use only original equipment or equivalent parts from GlasCraft in the catalyst system i e hoses fit tings etc because a hazardous chemical reaction may result between substituted parts and MEKP To prevent contact with MEKP appropriate personal protective equipment including chemically imperme able gloves boots aprons and goggles are required for everyone in the work area Polyester Resins and Gel Coats Servis materials containing polyester resin and gel coats creates potentially harmful mist vapors and atomized particulates Prevent inhalation by providing sufficient ventilation and the use of respirators in the work area Read the material manufacturer s warnings and ma terial MSDS to know specific hazards and precautions related to polyester resins and gel coats To prevent contact with polyester resins and gel coats appropriate personal protective equipment including chemically impermeable gloves boots aprons and goggles are required for everyone in the work area Spraying and Lamination Operations Remove all of overspray sand ings etc from the building as they occur If this waste is allowed to build
7. p n FM 494 over the hose assembly and leave it loose until the hoses are attached to the gun E E E E 15 a Group the hoses together as shown and wrap them with tape about every 2 feet b Start approx 12 in back from the gun and tape the end of the black scuff jacket with black tape Spread the black scuff jacket out so it fits snug around the hoses and tape the other end with black tape Rotate trigger lock to stop the trigger from being activated 12 Attach the black p n 21694 material hose to the material inlet fitting on the back of the gun 13 Attach the yellow p n 236 or 236 xx solvent hose to the inlet fitting on the back of the gun 10 GC 1317D Set Up Secure the four hoses to the boom with binding straps p n 22546 00 Route the four hoses between the two springs Secure the four hoses to the boom with binding straps p n 22546 00 16 Start At This End Route the four hoses from the gun through the boom as shown using binding straps p n 22546 00 to secure the hoses to the boom GC 1317D 11 Set Up Indy Dispense Gun 17 Attach all hoses and tubing as shown This diagram 1 for displaying point to N point hook up ONLY and DOES NOT suggest actual routing of hoses and tubing All hoses and tubing should be routed neatly free of any moving components From Boom Fluid Section 21179 00 Red Tubing 20190 xx Catalys
8. up spillage of catalyst is more likely to start a fire If cleaning solvents are required read material manufacture s warnings and material MSDS to know specific hazards and precautions GlasCraft recom mends that clean up solvents be nonflammable GlasCraft recommends that you consult OSHA Sections 1910 94 1910 106 1910 107 No 33 Chapter 16 17 NFPA No 91 for further guidance Grounding This equipment needs to be grounded Ground the dispense gun through connection to an GlasCraft approved grounded fluid supply hose Check your local electrical code and related manuals for detailed grounding instructions of all equipment in the work area N A grounding wire clamp are provided assembly p n 17440 00 with all FRP equipment Notice The Mast must be secured in the retracted position and held secure to prevent rotation before transporting the system GC 1317D Set Up Any mounting option cart mast and boom floor 3 Slide catalyst jug bracket over the mast and DO NOT mount or wall mount should be completely TIGHTEN assembled before starting the following steps Tools Required 1 Standard wrench amp socket set 2 Standard hex key set 3 Tape measure or yard stick All Required tools are standard sizes MAST 1 Attach casters to base plate CATALYST JUG BRACKET 170 7755 42 NUT 7754 1010 WASHER 7486 04 FLAT WA
9. CO These items sold but not manufactured by Graco such as electric motors switches hose etc are subject to the warranty if any of their manufacturer Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties In no event will Graco be liable for indirect incidental special or consequential damages resulting from Graco supplying equipment hereunder or the furnishing performance or use of any products or other goods sold hereto whether due to a breach of contract breach of warranty the negligence of Graco or otherwise FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document as well as all documents notices and legal proceedings entered into given or instituted pursuant hereto or relating directly or indirectly hereto be drawn up in English Les parties reconnaissent avoir convenu que la redaction du presente document sera en Anglais ainsi que tous documents avis et proc dures judiciaires executes donn s ou la suite de ou en rapport directement ou indirectement avec les procedures concern es Graco Information TO PLACE AN ORDER contact your Graco distributor or call to identify the nearest distributor Phone 1 800 746 1334 or Fax 1 330 966 3006 All written and visual data contained in this document reflects the latest product information available at the time of publication Graco reserves the right to make
10. D 3 Clean pump lube cup and add fresh pump lube 29 30 Technical Data Category Data 050 Catalyst Chemically coated aluminum stainless steel chemically resistant o rings Resin Carbon steel carbide chemically resistant rings GC 1317D Notes GC 1317D 31 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use With the exception of any special extended or limited warranty published by Graco Graco will for a period of twelve months from the date of sale repair or replace any part of the equipment determined by Graco to be defective This warranty applies only when the equipment is installed operated and maintained in accordance with Graco s written recommendations This warranty does not cover and Graco shall not be liable for general wear and tear or any malfunction damage or wear caused by faulty installation misapplication abrasion corrosion inadequate or improper maintenance negligence accident tampering or substitution of non Graco component parts Nor shall Graco be liable for malfunction damage or wear caused by the incompat ibility of Graco equipment with structures accessories equipment or materials not supplied by Graco or the improper design manufacture installation operation or maintenanc
11. Operation GLASCRAFT COMPOSITES EQUIPMENT BY GRACO Internal System GC 1317D Low Emission Internal Mix Gel Coat For use with Polyester Resin and Gel Coat Maximum fluid working pressure 20864 05 1300 psi 9 MPa 90 bar 21780 01 1700 psi 12 MPa 117 bar 22026 01 2000 psi 14 MPa 138 bar Maximum air pressure 100 psi 0 7 MPa 7 bar Important Safety Instructions Read all warnings and instructions in this manual Save these instructions Contents Warnings WV ENING a va er a bi 3 oalet IMMOFMAUOM ae ane ach eee eee aes 5 CO 6 Set up De UMS IMU CHONG 7 aaa 19 eee 20 22 A 23 ASSembDIV Drawings aa E Ba aja Na aa alang SUDFASSEMDIY ane 24 Maintenance eee eee eer eee eee eee 29 Technica
12. SHER 8 NG SA lt 18291 01 20568 00 CASTER 4 Loosen clamp bolts to expose pump mounting bracket Attach pump mounting bracket to the air motor Use thread locker on the threads and tighten bolts as tight as possible 2 Insert mast into base socket and secure with supplied bolts PUMP MOUNTING BRACKET 19890 00 GC 1317D Set Up 5 a Stand pump assembly next to the mast and 6 Mount catalyst bottle approximately 26 from the top of install the pump mounting bracket the base plate to the bottom of the catalyst bracket PUMP MOUNTING BRACKET b Lift to desired height approximately 36 from the top of the base to the bottom of the pump mount ing bracket Use 3 4 wrench and tighten as tight as possible PUMP MOUNTING BRACKET TaN 36 APPROX GC 1317D Set Up 8 Remove the pump inlet saftey cap and drain the testing oil into an open container Attach green pick up hose to the pump inlet fitting and tighten 9 Attach green pick up hose to the pick up tube 9 FOR INDY GUN INSTALLATION BEGIN STEPS 10 THRU 17 FOR FORMULA GUN INSTALLATION BEGIN STEPS 18 THRU 26 Fo i le GC 1317D Set Up Indy Gun Option 14 Attach the stainless steel p n 20190 xx catalyst hose to the catalyst inlet fitting on the back of the gun 10 a Lay all of the hoses out straight VOKI AT b Slide the supplied black scuff jacket
13. distributor for information Route hoses and cables away from traffic areas sharp edges moving parts and hot surfaces Do not kink or over bend hoses or use hoses to pull equipment Keep children and animals away from work area Comply with all applicable safety regulations PRESSURIZED ALUMINUM PARTS HAZARD Do not use 1 1 1 trichloroethane methylene chloride other halogenated hydrocarbon solvents or fluids containing such solvents in pressurized aluminum equipment Such use can cause serious chemical reaction and equipment rupture and result in death serious injury and property damage GC 1317D Important Safety Information Methyl Ethyl Ketone Peroxide MEKP MEKP is among the more hazardous materials found in commercial channels Proper handling of the unstable reactive chemicals presents definite challenge to the plastics industry The highly reactive property which makes MEKP valuable to the plastics industry in producing the curing reaction of polyester resins and gel coats also produces the hazards which require great care and caution in its storage transportation handling processing and disposal Workers must be thoroughly informed of the hazards that may result from improper handling of MEKP especially in regards to contamination and heat They must be thoroughly instructed regarding the proper action to be taken in the storage use and disposal of MEKP and other hazardous materials used in the laminat
14. e of structures accessories equipment or materials not supplied by Graco This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect If the claimed defect is verified Graco will repair or replace free of charge any defective parts The equipment will be returned to the original purchaser transportation prepaid If inspection of the equipment does not disclose any defect in material or workmanship repairs will be made at a reasonable charge which charges may include the costs of parts labor and transportation THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE Graco s sole obligation and buyer s sole remedy for any breach of warranty shall be as set forth above The buyer agrees that no other remedy including but not limited to incidental or consequential damages for lost profits lost sales injury to person or property or any other incidental or consequential loss shall be available Any action for breach of warranty must be brought within two 2 years of the date of sale GRACO MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES EQUIPMENT MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRA
15. end of the black scuff jacket with black tape Spread the black scuff jacket out so it fits snug around the hoses and tape the other end with black tape GC 1317D Set Up Secure the four hoses to the boom with binding straps p n 22546 00 Route the four hoses between the two springs Secure the four hoses to the boom with binding straps p n 22546 00 25 Start At This End Route the four hoses from the gun through the boom as shown using binding straps p n 22546 00 to secure the hoses to the boom GC 1317D 16 Set up Formula Dispense Gun 26 a Remove the plug from the side of the air manifold and install the regulator kit p n 22632 00 Be sure to PTFE tape the threads b Attach all hoses and tubing as shown c Connect material hose 20195 xx with supplied fitting 14626 00 This diagram is for displaying point to point hook up ONLY and DOES NOT suggest actual routing of hoses and tubing All hoses and tubing should be routed neatly and free of any moving components 22632 00 TI Z TI 9 Va gt J7 20190 Catalyst Hose Fluid Section From Boom 9704 03 Clear Tubing 21179 00 Red Tubing 236 or 236 Solvent Hose 20195 xx Material Hose Air Lines Clear Tubing mu Material Hoses mum Catalyst Hose GC 1317D Set
16. go of the trigger and hand stroke pump again to develop 300 400 PSI 21 28 bar STOP a Solvent flush the gun STOP MDA Do not exceed 20 PSI 1 4 bar pressure on the Material Regulator until steady material flow has been established GC 1317D 21 Shut down 2 Push down the yellow slide valve P N 21402 00 on the inlet air to bleed off air on system Shut Down Instructions Follow pressure Relief Procedure on page 21 Due to the different O Ring materials and lubricants used in the Guns never submerge or soak any dispense gun in any type of solvent Submerging or soaking any Gun will immediately void the Gun warranty 3 Turn catalyst yellow ball valve P N 21228 00 to Open Recirculation position to dump psi and close the valve 1 Activate trigger lock to stop the trigger from being activated Refer to gun manuals if needed 4 Pressure should be maintained on the resin hose If you are using the Indy gun install the night plug p n 23527 00 N Refer to gun manuals for service and maintenance ush in and rotate trigger lock p n 23774 00 Formula Gun 22 GC 1317D Parts Model Internal Gel Coat System Standard Equipment Part SSP 160 01 SUPER CATALYST SLAVE PUMP ASSEMBLY GAM 268 01 MATERIAL PUMP PICK UP KIT 21694 25 MATERIAL HOSE ASSEMBLY 25 FT 17440 00 GROUNDING CLAMP ASSEMBLY Pump Options Part Descript
17. ing operation MEKP is flammable explosive as well as potentially damaging to the eyes and skin Read material manufacturer s warnings and material MSDS to know specific hazards and precautions related to MEKP Contaminated MEKP can become explosive Prevent contamination of MEKP with other materi als which includes but is not limited to polyester overspray polymerization accelerators and promot ers and non stainless metals Even small amounts of contaminates can make MEKP explosive This re action may start slowly and gradually build up heat which can accelerate until fire or an explosion result This process can take from seconds to days Heat applied to MEKP or heat build up from con tamination reactions can cause it to reach what is called its Self Accelerating Decompisition Tempera ture SADT which can cause fire or explosion Spills should be promptly removed so no residues remain Spillage can heat up to the point of self ignition Dispose in accordance with manufacture s recommendation Store MEKP in cool dry and well ventilated area in the original containers away from direct sunlight and away from other chemicals It is strongly recom mended that the storage temperature remain below 86 F 30 Heat will increase the potential for ex plosive decomposition Refer to NFPA 432 Keep MEKP away from heat sparks and open flames GC 1317D Current catalysts are premixed and do
18. instructions Use only grounded hoses Hold gun firmly to side of grounded pail when triggering into pail If there is static sparking or you feel a shock stop operation immediately Do not use equipment until you identify and correct the problem Keep a working fire extinguisher in the work area See additional information on MEKP in the MEKP Section of this manual PERSONAL PROTECTIVE EQUIPMENT You must wear appropriate protective equipment when operating servicing or when in the operating area of the equipment to help protect you from serious injury including eye injury inhalation of toxic fumes burns and hearing loss This equipment includes but is not limited to e Protective eyewear e Clothing and respirator as recommended by the fluid and solvent manufacturer e Gloves Hearing protection TOXIC FLUID OR FUMES HAZARD Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin inhaled or swallowed e Read 505 to know the specific hazards of the fluids you are using e Store hazardous fluid in approved containers and dispose of it according to applicable guidelines e Always wear impervious gloves when spraying or cleaning equipment GC 1317D Warnings SKIN INJECTION HAZARD High pressure fluid from gun hose leaks or ruptured components will pierce skin This may look like just a cut but it is a serious injury that can result in amputation Get immediate surgical treatment Do not
19. ion Number 20864 05 MATERIAL PUMP ASSEMBLY 11 1 RATIO 21780 01 MATERIAL PUMP ASSEMBLY 17 1 RATIO 22026 01 MATERIAL PUMP ASSEMBLY 20 1 RATIO Material Spray Nozzles See gun manuals for spray tip options GC 1317D 23 Sub Assembly Drawings LPA 165 Bottle ARE 21044 01 21039 00 21040 00 INCLUDES NUTS 24 Part Description Number 167 1 BOTTLE LPA 172 SCREEN REVISION o f ueo 4 2 Mun 4 4 TT REVISION GC 1317D Sub Assembly Drawings GAM 268 01 Material Pick Up Kit 20395 00 0520 72 20394 00 Parl ar 20394 00 PICK UP TUBE 20395 00 ELBOWFITTING 20397 01 MESH FILTER 20398 02 MATERIAL HOSE Filter FilterOptions 0 0 Part Description Number 20397 02 100 MESH 20397 03 50 5 20391 01 REVISION GC 1317D 25 Sub Assembly Drawings 18318 02 Part 23555 00 Air Manifold 8113 03 14626 017 REVISION 20794 01 Solvent Tank Part ee Description Qty Number Bi 20655 01 SOLVENT TANK ENG RM 8 6 04 ISD 141 3 20324 00 Part Sh REVISION D 26 GC 1317D 27 1 11 00 16006 618922 91 6978 NOILONYLSNI DLW 598 08 335 1 Z00Z91L HOLVINSNI LYH Ec cveVv 00 26 112
20. l Data Technical Dala 30 NOIES 31 Graco Standard Warranty 32 Graco Olio Informati n 32 Non Applicable 2 GC 1317D Warnings The following warnings are for the setup use grounding maintenance and repair of this equipment The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure specific risk Refer back to these warnings Additional product specific warnings may be found throughout the body of this manual where applicable e See Important Safety Information MEKP Polyester Resins and Gel Coats and Spraying and Lamination Operations section of this manual FIRE AND EXPLOSION HAZARD Flammable fumes such as solvent and paint fumes in work area can ignite or explode To help prevent fire and explosion Use equipment only in well ventilated area Eliminate all ignition sources such as pilot lights cigarettes portable electric lamps and plastic drop cloths potential static arc Keep work area free of debris including solvent rags and gasoline Do not plug or unplug power cords or turn power or light switches on or off when flammable fumes are present Ground all equipment in the work area See Grounding
21. point gun at anyone or at any part of the body Do not put your hand over the dispense outlet Do not stop or deflect leaks with your hand body glove or rag Engage trigger lock when not spraying Follow Pressure Relief Procedure in this manual when you stop spraying and before cleaning checking or servicing equipment MOVING PARTS HAZARD Moving parts can pinch or amputate fingers and other body parts Keep clear of moving parts Do not operate equipment with protective guards or covers removed Pressurized equipment can start without warning Before checking moving or servicing equipment follow the Pressure Relief Procedure in this manual Disconnect power or air supply EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury Do not operate the unit when fatigued or under the influence of drugs or alcohol Do not exceed the maximum working pressure or temperature rating of the lowest rated system component See Technical Data in all equipment manuals Use fluids and solvents that are compatible with equipment wetted parts See Technical Data in all equipment manuals Read fluid and solvent manufacturer s warnings For complete information about your material request MSDS forms from distributor or retailer Check equipment daily Repair or replace worn or damaged parts immediately with genuine manufacturer s replacement parts only Do not alter or modify equipment Use equipment only for its intended purpose Call your
22. t Hose a 21694 m Air Lines Clear Tubing Material Hoses mum Catalyst Hose 12 Material Hose GC 1317D Set Up Clear Tubing 1 4 in Clear Tubing 1 8 in 236 or 236 xx Solvent hose Solvent Pot GC 1317D Catalyst Bottle 20260 00 Recirculation Hose tape together with green material hose Do Not insert the hoses in the material drum until the system has been flushed Clear Tubing 3 8 in GAM 268 01 Pick Up Kit 13 14 Set Up Formula Gun Option 18 a Lay all of the hoses out straight b Slide the supplied black scuff jacket p n FM 494 over the hose assembly and leave it loose until the hoses are attached to the gun NANG ANNA ANANA PE NANA ANNA ANAN 19 Push in and rotate the trigger lock to stop the trigger from being activated 21 Attach the clear p n 9704 03 trigger air tubing to the trigger air inlet fitting on the back of the gun 22 Attach the yellow p n 236 or 236 xx solvent hose to the solvent inlet fitting on the back of the gun 23 Attach the stainless steel p n 20190 xx catalyst hose to the catalyst inlet fitting on the back of the gun 24 a Group the hoses together as shown and wrap them with tape about every 2 feet b Start approx 12 in back from the gun and tape the
Download Pdf Manuals
Related Search