DVD & CD Duplication systems DVD Duplication - CD
Contents
1. Yes the L and C for the example above will disappear Setting No will keep the display as above 23 Press MODE switch to change and GO to exit 1 10 1 21 Read cdda index 0 The setting controls the copying of data existing in index0 Seting Yes will copy the data and setting No will make it empty Press MODE switch to change and GO to exit 1 10 2 Edit The edit function located in the sub function menu is a track selecting function that can combine tracks on different CD discs onto one single CD disc For example you can make a collection of favorite songs from different music CDs and store them into one CD disc Switch to the Clear function to delete the data if any in the hard drive s partition intended to store the music tracks Switch to EDIT by pressing the MODE switch in sub function Load your master CD into the CD drive if there is no hard drive installed the blank CD R or CD RW discs must be inserted to the CD writers for track at once copy Duplicator will analyze the master CD and show total xx tracks on the LCD display and finally stop at gt Begin track 0 Quit Press the MODE switch to change the number of tracks song that you wish to start with and then press the GO switch to quit After quitting the LCD display will stop at End track 0 Quit The number selected must be same or larger than that selected in Begin track The same number2. writers the duplicator will automatically copy information onto the blank discs e When a copy is completed the target disc will be ejected automatically default setting Passed discs will be ejected This means that completed discs that 8 h are correctly copied will automatically eject themselves This setting can be changed according to your need For continuous duplication place additional blank disc s into the writer and repeat the above procedures Failed discs will remain in writer Press the eject button on the writer to eject the disc manually The duplicator will prompt you with an error message when you try to copy a partition that contains no data In this case switch to the Load function to load data first Do not press any switches on the duplicator during operation This will cause an interruption Any interruption termination of an operation will cause an error and might lead the duplicator to malfunction depending on writers installed The target disc will be ruined and cannot be used again BB Without hard drive a b Switch to Copy by pressing the MODE switch Place the blank target disc into the writer Duplicator will start copying when writer detects the target disc When Copy is completed the correctly copied CD DVD discs will be ejected automatically Default setting Passed or correctly copied discs will be ejected This can be changed according to your need For
3. for CDs and 5GB sections for DVD partitions The number of partitions available depends on the hard drive s capacity No pre formatting or software setup is required to install the hard drive Each partition in the hard drive will be labeled in alphabetical order starting from AA AB AC etc The current partition number can be selected under HDD partition in the Setup menu The duplicator will show an error message when you try to copy it from a partition that contains no data Switch to the proper partition or use Load function to load the master data onto the current partition 1 8 External External functions are reserved for releasing the control of devices installed on duplicator The external function will be activated when switching to this function for five seconds To return to other functions of the duplicator after the External function is activated you have to re start the duplicator 1 9 Quick erase This function only works with rewriteable discs The data on rewriteable discs will be erased after executing this function 1 10 Sub function In the main menu press and hold down the MODE switch for five seconds and the menu will be switched to sub function menu and vice versa 1 10 1 Setup Since there are many different settings for this duplication system we suggest that you use the original default settings for optimal performance Changes should be made only when you are familiar with the f
4. means you want to select a single track and larger number means you want to select a sequence of tracks in that particular CD After selecting the End track the duplicator will bring you back to the Begin track selection Repeat the same procedure to collect other tracks in a different sequence that you want to copy If no other tracks are selected press the GO switch directly at Begin track and press GO at End track to exit Duplicator will start loading those music tracks selected into the current partition of the hard drive After you finish loading the master CD will be ejected automatically and the LCD will display Pass You may change the master CD and run the Edit function again to gather more music tracks from different master CDs When finishing the collection switch the function to Copy and place blank CD discs or CD RW discs into CD writers for copying If there is no hard drive installed and selection of music 25 tracks from the master CD in CD ROM drive is completed the duplicator will prompt you the message Finalize No Quit If there are still other tracks that need to be collected the setting of Finalize must be No Press the GO switch to quit The duplicator will start to copy the selected tracks onto the blank CD disc After finishing the copy the master CD will be ejected automatically and prompt you to Pass in the LCD display You will note that the CD discs in the tar
5. quality or unstable disc writing Under this circumstance lowering the writing speed in this setting will help you get a higher success rate in disc writing However if you lower the writing speed the duplicator will take more time to copy CDs DVDs Press MODE to change the setting and GO to exit 1 10 1 7 DVD Write Speed This option is for DVD duplicating controller card only and is not available with the CD controller card This setting controls the DVD writing speed of the writer The default setting for the controller is MAX which would use the highest writing speed of the writer Sometimes using the maximum writing speed will cause a high failure rate that may be due to poor disc quality or unstable disc writing Under this circumstance lower the writing speed in this setting to get a higher success rate in disc writing Some DVD writer brands will restrict the writing speed on certain DVD discs due to an unauthorized patent This is due to the writer itself Press MODE to change the setting and GO to exit 1 10 1 8 CD ROM drive The ROM drive can be selected manually Default setting is AUTO and the duplicator will select the ROM drive automatically If the drives are installed correctly the setting option will be in series like ATA1 0 and the writer will be like ATA2 0 The 0 in ATA1 0 and ATA2 0 means the drives are in master mode and 1 and 2 means the channel number The digit after the dot represents the m
6. termination during operation The duplicator may malfunction and you can only reset the machine by re starting the power Note that the emulation function is useful when you want to test whether master disc can be copied onto target discs 1 4 Emu Copy This function combines the emulation and copy function within one selection First the machine will do the emulation and then continually copy the disc if no errors occur during the emulation process The correctly copied discs will be ejected and failed discs will remain in the writer Failed discs must be removed manually 1 5 Compare This function performs a data comparison between the master disc and target discs Only data discs will be compared fully VCDs music CDs or DVD movies will 12 perform the verification function instead 1 6 Verify This function does verifications of target discs A different disc in the writer and ROM drive can be verified together simultaneously 1 7 Load This function can only be used when a hard drive is installed in the duplicator Use the Load function to load the master data into the hard drive before performing another function Place the master disc into the ROM the duplicator will automatically detect and analyze the master disc and load its data into the current partition of the hard drive only if a hard drive is installed The hard drive installed on the duplicator will be automatically partitioned by 900MB sections
7. DVD amp CD Duplication systems DVD Duplication Controllers USER MANUAL AUN CONTENT Introduction ruvarvarvnrnvvrvnvrnrvnnnnnnsnvvnevnrnnsennennevnnnn 4 Installation Procedure rrrrurnunnnnnnnnvnnvnrnnvnnnnnnnvnnnn 5 O sesvacoacdcuosuasenees 7 FUNCTION seder 10 A GOUV EEE EE 10 4 2 Copy Compare rrrrnnnnnnnrnnnrrnnnnnnnrrnnnrrnnnnnnnre 11 TFT Prieur 11 4A EMU COP 12 AN ore 12 TOVE O A OE 13 7 FAY o A A 13 TEE Enlai 14 4 JOUICEK CASE m kene 14 4 10 SUD FUNCION vasen 14 AAO SOU en 15 24 O A E T T 24 28 4 GC We gt eee ee eer N a 28 ASV OA ClO Ale sr 28 A EK CODY XT EE 29 4 106 emulate xi 2 eden 29 A lO CODY AA E E ce 30 4 10 8 emulate X2 una 30 F10TC00 hint 30 4 10 10 emulate X4 oeeie enait aae 30 ANOA CODY XO das 31 4 10 12 emulate X8 tarta net eases 31 4 10 13 burn in AA EAE beans a essere 31 4 10 14 Update oocccccccconconccccocconcnononnnncnnnancnns 32 4 10 1510560L asked ddeintede 32 5 Standard CQuipMent ccccccceceeeeeeeeeeeeeeeees 39 6 Circuit CrAWING ccccceceeeeeeeeeeeeeeeeeeeeaeeaeeess 34 TTroubleshoolng ca is 35 Device SUPPO sir seas see 38 SJ 0 0151 6 gt Gee ei dci 40 1 Introduction Thank you for choosing this CD DVD duplication controller duplicator This duplicator system will surely help you achieve your duplication needs Features 1 Stand alone design no PC or software required 2 Easy to operate No training requir
8. It only means that it can reach a maximum speed of 52X during a certain stage and is not always at this speed A qualified reader must always sustain the 38 reading speed above the writing speed if you need to do on the fly copy from CD ROMs to CD Rs For IDE DVD ROM 1 Teac DV 516D 2 EPO DVD 8216 Note To link with the maximum target numbers of the DVD writer some brands of DVD ROM will be a little bit slow in data transfer bandwidth and such DVD RW writers are not suggested for use with the controller board since it might reduce the target numbers If a hard drive is added this consideration can be omitted For IDE CD R RW writer 1 Plextor W4824TA W5232TA 2 Lite On LTR 48245 52327 3 Teac W552G 4 Sony 230E For IDE DVD writer 1 Pioneer 106 A06 107 A107 2 Teac W58D 3 Plextor 708A 4 NEC 2500A The brands models of the DVD CD writers listed above are supported by our duplication controller cards or 39 duplication systems Most other drives that are not listed above will work as well 8 Appendix CONTACT THE DISTRIBUTOR IF TROUBLE OR PROBLEMS ARISE FOR PROMPT FEEDBACK amp IMMEDIATE SERVIGE PLEASE MAKE NOTE OF FULL DETAILS FOR DIAGNOSIS 40
9. N different usages Our design provides an easy way for customers to reset their controller boards as noted below 1 Turn off the duplicator and wait for about 10 seconds If the duplicator is not in use at the moment ignore this step and go directly to procedure 2 2 Press and hold down the MODE switch and turn on the power of duplicator at the same time Release the button until the clear setup message is shown on the LCD display 3 If the clear setup message is not shown repeat the whole procedure above 4 All settings on the duplicator will be restored to its factory default settings after a correct reset procedure Standard equipment Controller only Controller fixed on a 5 25 bay 20 x 2 LCD display on 5 25 bay Operation manual ATA 66 IDE cables eight pieces Other equipment according to agent s assembly 5 Circuit drawing LCD BIOS UP TEITE EE JR akk Gehen oy fr LE E E EE AAA ka IDES LE E oe RR PCR 3 COM2 COM1 CD DVD ROM HDD POWER CD 398 amp DVD 3000 Controller card 6 Trouble Shooting A Check whether the connection of the power cable and the power outlet s environment is normal B Check the power supply fan It should rotate if the power is on If not the power supply might have a 35 problem Turn off the power of the machine Open the duplicator case to check whether the power cable is fixed 2Q There s
10. an error message shown on the LCD A During the use of functions such as Copy Emulate Write compare and verify you may press the MODE switch to abort the operation An Error message will be shown on the LCD Aborting when using certain writers might cause the duplicator to lock up If this occurs you must re start the power to return the duplicator back to normal A failed reading may cause the error message shown on the LCD display Change the master disc to try again During operation if you read a message indicating buffer under run or writing error occurs the LCD will show an error message like Pass xx failed xx If there is no device connected and detected by the duplicator during power on the duplicator will show an error message on the LCD before entering the main menu 3Q The ROM doesn t read disc and shows an error message Check the format of the master disc or the master disc itself for damage 36 B Use any of the writers to read the master If it works the ROM drive may be defective or incompatible with the disc 4Q Switches do not function A May still be busy on the task B Button malfunction C Faulty board 5Q COPY is completed but the target disc is not readable executable A Use the compare function to check B Change to another ROM drive to test 6Q The failure rate is high A Lower the speed of writers and try again B Quality of blank disc is poor C Check for
11. aster 0 and slave 1 mode The digit before dot represents the channel number E g ATA2 1 means the channel 2 in slave mode Press MODE to change the setting and GO to exit 1 10 1 9 Autoloader This duplicating controller card can be used as an independent controller card for external autoloading If the autoloader is installed this setting must be set to an appropriate setting such as CDF 4800 classic or extended The default setting is No Press MODE to change the setting and GO to exit 1 10 1 10 Load nonblank disc This setting is mainly for the autoloader and controls the loading of a non blank disc in any writer If the setting is Yes whenever there is a non blank disc detected by the writer the duplicating controller card will automatically go to the Load function and start loading the data from that non blank disc into current partition of hard drive Through this function you can control the autoloader to copy multiple master discs automatically Press MODE to change the setting and GO to exit 1 10 1 11 CD DA load speed Normally when reading music tracks the ROM drive will automatically lower the reading speed significantly An unstable reading situation may occur if we use the maximum default soeed of ROM drive to read music track This will affect the quality of music CD duplicated This setting selects the speed of music 20 track loading to enhance stability of mus
12. continuous duplication place additional blank target discs into the writer and repeat the above procedures c Failed discs will remain in the writer Default setting Failed disc NOT ejected This can be changed according to your need Press the eject button on the writer to eject discs manually 4 Function The function explained below is based on the factory s default setting Different settings will cause duplicator to react differently Please press and hold down the MODE switch while turning on the power the duplicator will return to the factory s default setting 1 1 Copy Make sure the present partition in hard drive is correct and it contains data with hard drive installed or the master CD DVD is inserted in the ROM drive without hard drive installed before copying Place blank target disc into the writer When writer detects the target disc the duplicator will start copying automatically When a copy is finished correctly copied discs will be ejected automatically and failed ones will not be ejected You can remove failed discs by pressing the eject button on the writer manually Put a new target disc in the writer for additional copying Rewriteable discs containing data can also be copied by the duplicator if writers installed are capable of rewriteable 10 disc writing Data stored in the rewriteable disc will be erased automatically before copying new data No special setting or procedure is required to erase
13. d on the writer If it supports auto ejection the tray will be ejected after copying If not the tray will not be ejected even when setting is Yes Press MODE switch to change and GO to exit 1 10 1 16 Skip read error This setting controls error skipping during the master disc reading The default setting is No When an error is detected during loading the duplicator will stop to load and display an error message If the setting is Yes there will be no message shown even if there is an error during reading You can use this function to copy master discs that have errors Press MODE switch to change and GO to exit 22 1 10 1 17 MODE 2 compare This setting can be activated to compare some data format stored in MODE 2 disc Default setting is Press MODE switch to change and GO to exit 1 10 1 18 Startup command This setting specifies the first function to appear when the duplicator is turned on to avoid repeated selection Press MODE switch to change and GO to exit 1 10 1 19 LED offset This setting controls the offset position for the LED display on different kinds of cases Press MODE switch to change and GO to exit 1 10 1 20 LCD mile 2 digits This setting controls the display mode for processing meter during operations on the LCD display e g L12 C12 C12 C12 C12 The L represents the Load and C represents the Copy before the 2 digit number If you set this option to
14. determine whether or not it runs automatically when the master disc and target discs are both placed in the drives of the duplicator If the option is set to O it means the start of duplication must run manually You will have to press the GO button each time to activate the duplication If option set to 1 as soon as the master and target disc are ready in both drives on the duplicator duplication will start automatically For duplicating the same master disc it is suggested to set this option to 1 and this will enable you to start the duplication immediately when you re insert blank target discs into writers Pressing the MODE switch will change the option and press GO to bring you to next setting 1 10 1 5 Write method This setting controls the writing methods of CD discs such as Disc at once or Track at once Disc at once will be the default setting Some CD writers may support different writing methods If the method selected is not supported the duplicator will automatically switch to the other one This function is only available for CD disc writing but not for DVD writing Pressing the MODE switch will change the setting and the GO switch will bring you to next setting 1 10 1 6 CD Write Speed This setting controls the CD writing speed Default setting is MAX which uses the highest writing speed of the writer Sometimes maximum writing speed will cause high failure rate that may be due to poor disc
15. ease set hard drive to the master mode and ROM in slave mode and the other is for CD DVD writer 5 3 The BIOS is fixed and welded on the controller board and cannot be replaced directly The upgrade of BIOS program can be completed in two ways One method is to run the upgrade function from the machine and the other is to use the upgrade kit to upgrade the BIOS chipset directly though JP2 BIOS UP port built in on controller board 4 The USB 2 0 interface is not bundled with the controller card It will not be available if you have only purchased the controller card B Whole duplicator without ROM and writer installed 1 Unpack the package of duplicator b Prepare the CD DVD writer according to the device recommendations in this manual and refer to the Part A above for installation Please contact duplicator vendor for unlisted CD DVD writer if needed 1 Check the entire unit Return it to your supplier if the unit is damaged in any way 2 Assemble the duplicator according to your need 3 Make sure the input voltage is either AC 110V or 220V C Completed duplication system 1 Unpack the duplicator package 6 2 Check the entire unit Return it to your supplier if there are any problems 3 Make sure the input voltage is either AC 110V or 220V 4 If your system did not come with a hard drive you can still install one if you wish 3 Operation 1 Turn the system on by pressing the power button and
16. ed 3 Copy Compare Verify Emulate Editing etc Functions 4 Compatible formats MODE 1 CD ROM XA MODE 2 Photo CD CD I VCD CD DA Multi session CD Plus 5 On the fly direct copy from CD ROM to CD or DVD ROM to DVD disc 6 Track selection is available for copying music tracks 7 Compatible with many brands of CD or DVD writers such as Plextor Sony Sanyo Yamaha TDK Nichimen Teac Lite On Ricoh Panasonic OptoRite etc 8 USB 2 0 interface offers you the flexibility of connecting to a PC built in with the default case IMPORTANT NOTE 2 Make sure the outside input voltage is either at AC110V or 220V Stable input power is required for normal operation Duplicator should be placed in a safe area within a clean and cool working environment Check and clean the master target discs before starting the duplication Do not touch recording surfaces of the target discs Do not move the duplicator during operation Installation Procedure You may receive the CD DVD duplicator in three configurations A Controller card only 1 You will need the following equipment a CD ROM DVD ROM drives b CD or DVD writer C Suitable case d Power supply 2 Assemble all required devices mentioned above and make sure to set devices to master mode The connector with power inlet on the controller card is for CD ROM DVD ROM Hard drive if the ROM reader and hard drive are both connected pl
17. ess MODE to number 8 at End track and Quit Press the GO switch to finish the selection for the 1 CD The duplicator will start to collect the tracks that you selected just now into the current partition of the hard drive After successfully loading the duplicator will eject your master CD and show Pass on the LCD Place No 2 CD into the CD drive and continue the selection for the second CD disc Repeat procedures d to k above Once the accumulated length of tracks selected reach the maximum 80 min capacity the 27 duplicator will stop accepting additional tracks o Switch to the Delete function to delete the last track stored in the current partition in the hard drive if necessary p Switch to the Copy function to start copying your own collection of music CD Example 2 No 1 CD All tracks No 2 CD 4 6 tracks a Load the No 1 CD disc normally by using LOAD function Data if any in the current partition will be erased and replaced automatically tracks of this CD b Load No 2 CD disc by using EDIT function but keep the data stored in hard drive The is no need to do Clear Master as described in Example 1 or you will lose the data of No 1 CD disc c Repeat the other procedures described in Example 1 1 10 3 Delete If the last music track stored in hard drive is not the one you wish to keep switch to the delete function and press the GO switch to delete it You may always use thi
18. get CD writers will not be ejected at this moment Duplicator will analyze the master data and bring you to the Begin track message on the LCD You can repeat the procedures described above to collect more tracks If the master CD is the last one that you collect change the setting Finalize to Yes and press the GO switch Duplicator will start to copy and close the CD discs in the CD writers If all of the CD discs are correctly copied they will be ejected from the CD writers automatically Please study the following examples carefully and follow the instructions step by step You will find it is easier to collect tracks through the duplicator Example 1 To make a new collection of two CDs listed below with hard drive installed 26 No 1 CD 4 6 8 songs 6 9 2 No 2 CD 3 6 9 13 16 songs a Switch to the Clear Master function and press the GO switch to clear data in the existing partition of hard drive Switch to the Edit function Place No 1 CD disc into CD drive under the EDIT function and wait for duplicator to analyze it Press the MODE switch to number 2 at Begin track and Press GO switch to quit When End track screen is shown on the LCD press the GO switch to quit directly since the first song number is 2 Press the MODE switch to number 4 at Begin track and Quit Press the GO switch again to quit Press the MODE function at number 6 at Begin track and Quit Pr
19. ic track reading Default setting is AUTO Press MODE to change the setting and GO to exit 1 10 1 12 Eject disc This setting controls the ejection of discs by the writer Three options are available Always means the writer will always eject the target disc no matter whether the operation is successful or failed No means disc will remain in the writer when job is completed You will have to eject the disc from the writer manually The Pass setting will eject the correctly copied discs automatically and leave failed ones in the writer Press MODE to change the setting and GO to exit 1 10 1 13 Buzzer This setting controls the ON and OFF of the buzzer Default setting is On Press MODE switch to change and GO to exit 1 10 1 14 CD G This setting activates the copy capability of the CD G format It cannot be copied if the writer doesn t support this format Default setting is No 21 Press MODE switch to change and GO to exit 1 10 1 15 Copycomp eject This setting controls the ejection of writer s tray under the copy compare function If the setting is Yes the tray will eject the passed disc after copying It will also re insert the disc again for subsequent comparison between the target disc and the source disc If the setting is No the tray will not be ejected between copy and compare The default setting is Auto which means the ejection of the tray will depen
20. latest BIOS version 7Q You can t boot up or it fails to upgrade BIOS A Contact your dealer to solve the problem Note you may be charged for this consultation B Check the BIOS program to determine whether it is correct Customers tend to download the wrong program or simply write the zipped file to CD which should be unzipped before writing 37 C Afailed upgrade might cause a failed boot up This can only be solved by returning the control board to the agent or the factory directly It is not necessary to return the entire system under a failed upgrade 7 Device support For IDE CD ROM l Any CD ROM drive that is compatible with all kinds of CD formats will be compatible if a hard drive is installed To install the 40X or above writer the accessing speed of CD ROM will definitely not be enough to support the high speed 40X 48X or 52X writing for direct copy from CD ROM to CD R The only way to improve the speed is to add a hard drive for the buffer Load first from the CD ROM to the hard drive and then copy from the HDD to a CD R If a direct copy from the CD ROM to CD R is preferred please lower the writing speed to less than 12X It will work with nearly all kinds of CD ROM readers in the market The 52 max reading speed listed on the front panel of CD ROM is not a reference that you may count on to run at speeds such as 40X 48X or even 52X on the fly writing from CD ROM to CD R 52X max
21. mulate x2 All operations will be the same as the Emulate write function except that the emulating speed will be twice as fast 1 10 9 Copy x4 Occasionally you will have to reduce the writing speed to 4x Switch to Copy x 4 All operations will be the same as the COPY except that the writing speed will be at 4x 1 10 10 Emulate x4 Under some conditions you will have to reduce the emulating speed of the writer to 4x instead of the normally faster speeds Switch to Emulate x4 All operations will be same as the Emulate write except that the speed will be at 4x 30 1 10 11 Copy x8 Occasionally you will have to reduce the writing speed of the writer to 8x Switch to the Copy x 8 function All operations are the same as COPY except that writing speed will be 8X 1 10 12 Emulate x8 Under some conditions you will have to reduce the emulating speed of writer to 8x Switch to Emulate x8 All operations will be same as the Emulate write except that the emulating speed will be at the 8x speed 1 10 13 Burn in This function is a burn in test function It will run the emulate write function continuously Between each cycle of the emulation the disc in the writer will be ejected automatically and re inserted again for continuous testing There is no real writing on the blank write once disc The disc will be remain blank throughout the process Re writeable discs that have data will be erased d
22. s function to delete the last track stored in the current partition of the hard drive 28 1 10 4 Clear This function clears the master data stored in the current partition of the hard drive When you want to EDIT a new collection of songs you must run this function first to clear the current partition of the hard drive Perform this function by pressing the GO switch and the LCD will show Master cleared 1 10 5 Copy x1 Under some conditions you will need to reduce the writing speed of the writer to a single speed Switch to Copy x 1 All operations will be the same as the COPY except that the writing speed will be on a lower speed Writing on the target disc using a lower speed will offer you better quality than using maximum speed You can use the disc copied under lower speed as a master for repeated duplication or use 1 10 6 Emulate x1 Under some conditions you will have to reduce the emulating speed of writer to single speed Switch to Emulate x 1 all operation will be the same as the Emulate write except that the emulating speed will be single time only 29 1 10 7 Copy x2 Occasionally you will have to reduce the writing speed of the writer to double the speed Switch to Copy x 2 All operations are the same as COPY except that the writing speed will be x2 1 10 8 Emulate x2 Under some conditions you will have to reduce the emulating speed of writer to double the speed Switch to E
23. t holds 5GB Using this system no space on the hard drive will be wasted Once you start copying discs onto the HDD each partition will be represented by two letters such as AG BD etc AC means A group C partition and BD means B group D partition If you get a 40GB hard drive installed with the CD controller you might have 42 partitions beginning from AA to AZ and ending with BA to BP There will be two groups in your hard drive A group contains 26 partitions and B group contains 16 All the configurations will be completed automatically so you don t have to run special software utility to create the partitions Note that this setting is not available if there is no hard drive installed 1 10 1 3 CD to CD This setting controls the source location of master data Select Yes to bypass the existing hard drive and you can copy directly from ROM to writer or select No to copy target disc from data stored in current 16 partition of the hard drive This setting will not be saved during rebooting of the duplicator You will have to reset it after rebooting if you wish to use CD to CD while there is a hard drive installed This setting is not available if there is no hard drive installed In this case the only option is to copy from ROM to writer directly Press the MODE switch to change setting and GO to bring you to next setting 1 10 1 4 Start writers This setting controls the behavior of the writer It will
24. the old data 1 2 Copy Compare This function will copy and compare the correctly copied disc with the master source With this function the accurate discs will be ejected and reinserted again into the machine automatically to be compared with the source disc The correctly copied discs will be ejected automatically after comparison The failed CD disc will remain in the writer Press the eject button on the writer to eject the failed discs Only data CDs will be compared with the master VCD or music CDs will be verified self reading instead of being compared with the master even if the Compare function is selected 1 3 Emulate This function performs a function similar to the Copy function except that data is not written onto the target disc The target disc will remain blank when emulation is completed For rewriteable disc that contains data the emulate function will quickly erase all old data before emulation You should NEVER emulate on a target disc that contains important data Please note that the machine does not support the emulation on 11 DVD R discs temporarily If the emulate function is selected on DVD R disc the disc will instead perform the copy function on the CD Termination during the Emulation process will not affect the target disc They will remain blank Note that the data on rewriteable discs containing data may be destroyed and cannot be retrieved again Some writers may not support sudden
25. unctions Also please note that the function settings listed below are summaries that cover all kinds of duplication controllers or duplication systems that we build and might not apply to the system you purchased 1 10 1 1 Show drive This setting shows the devices that are connected on the duplicator such as the CD DVD ROM writers and hard drive etc It also displays the version of drives currently installed on the duplicator 1 10 1 2 HDD partition group This setting assigns the current working partition group onto hard drive if installed Press the MODE switch to change the setting and press GO to exit After selecting the partition group pressing the exit button will bring you to the next sub function titled HDD partition of A for more selections for the partition number in that group After choosing the partition number press the exit button to bring you back to Copy function to the main menu Modern hard drives normally have large capacities In 15 order to organize and utilize the capacity well the controller will manage the capacity using two level management partition group and partition number The partition group serves as a folder and the partition number serves as an object in the folder By using this idea the controller can have up to 26 folders each folder has up to 26 partition numbers a total of 676 26x26 partition numbers For the CD controller each partition normally holds 900MB For DVD i
26. uring the burn in Please do not use re writeable discs with important data under burn in function 1 10 14 Update Functions of the duplicator will be improved for better performance or for other reasons when you update the BIOS This function will update your firmware to either later or previous versions for specific reasons Load the CD disc containing the desired firmware data BIOS CD disc into ROM drive and the duplicator will find the data and update its firmware automatically During updating don t turn the machine off because the update will not be finished until machine resets itself Note Turning off the machine during updating might cause severe problems such as a failure to boot Procedures to complete the upgrade 1 Get the BIOS firmware from your Vendor 2 Unzip the BIOS firmware you have gotten and write the file cdxxxx bin into the root directory of a blank CD R or CD RW disc The CD session has to be closed If the same CD disc still has capacity to add more data it can be used to store the newer version of BIOS When updating the BIOS program from the CD only the one in the last session will be used Other versions in previous sessions will be ignored 1 10 15 Reset The reset procedure is required for several reasons such as The assembling of the duplicator replacing a new brand of writers in an old duplicator or resetting the machine to factory default settings according to 32 2 Oe OO
27. you will see the self testing procedure running The following display will appear DVDxxxx V3 00 2003 Copy lt mode There will not be a message on top right corner if there is no hard drive installed 2 Different devices installed in the duplicator will require different operation procedures including two main categories AA With hard drive installed a The duplicator will automatically detect the hard drive and create partitions for it Each partition will have 900MB for CD duplicator and 5GB for DVD duplicator in capacity b You can select in the set up menu which partition will be the current partition to store the data in the HDD partition c If there is no data stored in present selected partition of the hard drive press the MODE switch to select Load function and place the master disc into the ROM drive The duplicator will automatically detect the master drive analyze and load the data into the present selected partition The master disc will be ejected when loading is completed In the case of an error the LCD will show the error message and the master disc will be ejected automatically You would then have to use another master disc to load the information onto the hard drive Master data can be stored in different partitions Please refer to HDD partition section for loading the master source d You can switch to copy function by pressing the MODE switch When you place blank discs into the
Download Pdf Manuals
Related Search