Dayton Audio DAX66 User Manual
Contents
1. mu ns T ZONEI ZONE2 ZONE3 SOURCE SOURCE2 SOURCE 3 PAIN ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE s ZONE 6 Ponce toc st olo 00 0 Gs em o o olo o oo HiHi zomea zones zones source SOURCES sources AL Lie sab Ta 12VOC TRIGGER OUTPUTS IR EMITTERS SYSTEM DC 12V daytonaudio com info daytonaudio com DAX66 INSTALLATION SPEAKERS INSTALLATION Speakers Use good quality 12 14 AWG stranded copper speaker wire Most jurisdictions require the use of CL2 rated in wall speaker wire refer to your local building code enforcement office for the proper cable type for your installation If speaker wires must be run parallel to AC wires keep the speaker wires and AC wires at least 10 inches apart If you must cross AC wires always cross at a 90 degree angle The DAX66 amplifiers are capable of driving 4 8 ohm speaker loads in stereo mode and 8 ohm loads in bridge mode Never connect more than two 8 ohm speakers wired in parallel to a single amplifier channel in stereo mode Never connect more than one 8 ohm speaker to a single channel in bridge mode Never connect the Left amp Right channels of the amplifier together or combine the negative channels of the amplifier Improp2. o looo O x Ga lo oo a On 0 5 Oz 006000 zov voles woes te zoles oo 8 8 oo EL e e E o o ojo o FECE Rotis Z Master Slave Select daytonaudio com info daytonaudio com DAX66 INSTALLATION RS 232 CONTROL DAX66 RS 232 Serial Port Control The DAX66 provides an RS 232 serial port for connection to and control by automation systems The DB 9 connector on the back of the unit supports bi directional RS 232 communication for third party automation systems An automation system can control all keypad and remote control functions for up to 18 zones 3 master controller units linked together using the included 18 pin expansion cable Baud Rate 9600 8 N 1 DB9 Connector Pin out TX RX GND DAX66 RS 232 CONTROL CR Carriage Return 0x0D No case capitalization lowercase CH Source Channel control CH 01 Control order structure lt xxPPuu CR 06 Source control Reply control order frame gt xxPPuu CR Inguiry command structure 1 xx CR xx stands for control object code xx stands for control object code 10 All Zone of Main unit 1 10 All Zone of Main unit 1 20 All Zone of Main unit 2 20 All Zone of Main unit 2 30 All Zone of Main unit 3 30 All Zone of Main unit 3 Zonel of Main unit 1 Zonel of Main unit 1 Zone2 of Main unit 1 Zone2 of Main
3. Set the MODE switch to STEREO 4 8 ohm speakers daytonaudio com info daytonaudio com DAX66 INSTALLATION SPEAKERS INSTALLATION Connecting 8 ohm speakers to the DAX66 in BRIDGE MODE In BRIDGE mode the amplifier LEFT and RIGHT outputs are combined into one large MONO amplifier thus doubling the output power to 50 watts with a minimum speaker load of 8 ohms Remove approximately 5 inches from the cable jacket strip 1 4 of insulation from the speaker wire and twist the copper strands Insert the speaker wires into the connector per the label below the output terminals and tighten the set screws Repeat for the remaining zones It is permissible to mix STEREO and Bridged MONO outputs on one DAX66 penson Vomer sarcros demo ege o ETUI ns232 o e gt a C et Aneis pm Pp S T I T INPUTS MK Es LE um zolee ANT HOME Zones source tomer SOURCES PAIN UN Loc oro l l OO 0 00 PEA i sons zones soma souca souices sacre mi corpo MO TIP x i tvoe TRIGGER OUTPUTS ie ewes sysrewoory ae FE CE RoHS Set the
4. BS Bass control BL Balance control CH Source control LS keypad connecting status Reply command gt xxPPuu CR daytonaudio com ued Baud Rate 9600 8 N 1 DB9 Connector Pin out Tx Rx GND Key in display Key in display Key in display Key in display Key in display Key in display Key in keypad Key in Key in 19200 Key in 38400 Key in 57600 Key in 115200 Key in 230400 1 lt CR change Source 1 Name aneeds to be 8 valid ASCII codes 2 lt CR change Source 2 Name 3 lt CR change Source 3 Name 4 lt 4 CR change Source 4 Name 5 lt 4 CR change Source 5 Name 6 lt 44 CR change Source 6 Name M lt CR change the name display on when turn on lt 9600 CR change RS232 speed rate to 9600 lt 19200 CR change RS232 speed rate to lt 38400 CR change RS232 speed rate to lt 57600 CR change RS232 speed rate to lt 115200 CR change RS232 speed rate to lt 230400 CR change RS232 speed rate to When unplugging and re plugging the AC power cord t ee Vol ff Tre gg Bas hh Bal ii Sou he baud speed rate returns to 9600 umecontrol status ble control status s control status ance control status rce control status jj keypad connect status info daytonaudio com DAX66 INSTRUCTIONS RS 232 CONTROL DAX66 RS 232 Serial Port Control continued Baud Rate 9600 8 N 1 DB9 Connector Pin out Tx Rx GND 00
5. ita ed Fil 0 O 00 0 0 OF Ole oy Waa oceans JU ome dem J l FE CE Ros X 12Vdc PA KEYPADS AC Input 12VDC trigger IN Input connects TRIGGER OUTPUTS to keypad hub activate external devices SPEAKER OUTPUTS 6 dedicated IR outputs Automatic Gain Control 50 watts 4 ohms in stereo mode and 1 global IR output brings low input levels 25 watts 8 ohms in stereo mode up to a pre set level 100 watts 8 ohms in bridge mode 12Vdc MUTE trigger IN daytonaudio com info daytonaudio com DAX66 KEYPAD FEATURES The DAX66 keypad is designed for ease of use with a maximum ability to control sound Soft touch backlit buttons and a backlit LED display provide convenient control of the zone ON OFF source 1 6 selection volume treble and bass A built in IR target or external IR target connected to the EXT IR terminals on the rear of the keypad relay commands to the DAX66 master controller Dedicated IR output jacks provide remote source control of the source equipment The built in IR target also provides complete zone control when using the DAXRC infrared remote control One DAXRC is included with each system and additional DAXRC are available from your Dayton Audio dealer Five LEDs on the keypad face indicate the operation mode of the keypad The EXT LED indicates that the system is receiving a trigger command from an external device Numeric LED Display Ext Mute PA selection LED Volume up down LED So
6. 12 Stereo mode 4 8 ohm speakers 70 volt speakers Powered Subwoofer daytonaudio com info daytonaudio com DAX66 INSTALLATION CONNECTING SOURCES Connecting Source Components to the DAX66 The DAX66 provides six source inputs that can be accessed by any zone Inputs 1 4 are stereo unbalanced line level source inputs via RCA style female connectors Input 5 provides a connection for a personal audio device or PC sound card via the 3 5mm stereo jack Input 6 provides one S PDIF input for a CD DVD cable or satellite box via the Toslink jack as well as a second 3 5mm jack The 3 5mm stereo jack on input 6 takes priority over the Toslink connector do not connect cables to both the Toslink and 3 5mm jack the same time Input 1 can be used as a paging or global all zones input When a source is connected to input 1 and 12Vdc is applied to the PA IN jack tip positive source 1 will be broadcast to all zones If there is no DC voltage is applied to the PA IN jack source 1 will operate like normal Infrared Emitter Outputs The DAX66 has an IR repeater system built in and each source has a corresponding Infrared IR emitter output The IR emitter output is tied to the corresponding source device or all global source control Program a universal remote to operate all six of the input devices
7. Point the universal remote at the DAX66 keypad to transmit the IR control codes through the DAX66 to the source devices With an IR emitter connected to an IR EMITTER output jack and the emitter placed over the source device IR receiver window the source devices can be controlled from any zone CD DVD or Music Player O RCA O i RCA go00000 T T Stereo IR Emitter Digital Optical EXPANSION T PRE cerca VOLTAGE SELECTOR omo main SS em MTO ECS ares ejo slo ZA T T T T T T 20461 m ONES SOME mn pE zone zone2 zones SOURCE SOURCE sowjces L ure coms CIO usti Heti s x j BEER Dios mes re a somces snes daytonaudio com info daytonaudio com DAX66 INSTALLATION 12V TRIGGERS Using the DAX66 12VDC Trigger Inputs and Outputs The DAX66 provides six 12Vdc trigger outputs which correspond to the six DAX66 zones When a zone is powered ON by the DAX66 keypad the corresponding zone s
8. Standby Standby Zone ON LED Peak LED Press the power button to turn the All zones are in standby mode until activated The PEAK LED indicates a connected system on and place all zones in by a keypad A BLUE LED indicates a zone source level is too high If the PEAK LED stand by mode is in standby mode a WHITE LED indicates emits a flashing or steady RED light reduce that a zone is active the zone input or output level daytonaudio com info daytonaudio com DAX66 MASTER CONTROLLER AMPLIFIER REAR PANEL Input 1 will override all zone inputs with 12Vdc applied to Bi directional the PA IN trigger jack RS 232 port a Input 5 3 5mm Stereo AVT ES Input 46 Toslink S PDIF ea eue or 3 5mm Stereo VOLTAGE EXPANSION IN OUT SELECTOR R Four stereo Connect up to 3 115V 230V MODE switch nj BRIDGE STEREO ROASINEUTS systems sonhe omrowvod cos 9 o ae e mM ERMI ot INPUT eT NS Em CN A a ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 i a k te orl o o o o 49 um O ani iri ri
9. disconnect Ol connected Reply command gt xxPPuu CR Inquiry command structure 2 xxPP CR needs to be 8 ASCII codes xx stands for control object code Key in 1 lt CR change Source 1 Name display 10 All Zone of Main unit 1 Key in 2 lt CR change Source 2 Name display 20 All Zone of Main unit 2 Key in 3 lt CR change Source 3 Name display 30 All Zone of Main unit 3 Key in 4 lt CR change Source 4 Name display 11 Zenel of Main unit 1 Key in 5 lt CR change Source 5 Name display 12 Zone2 of Main unit 1 Key in 6 lt CR change Source 6 Name display 13 Zone3 of Main unit 1 14 Zone4 of Main unit 1 Key in M lt CR change the name in the display 15 Zone5 of Main unit 1 On the keypad when the keypad is turned on 16 Zone6 of Main unit 1 Key in lt 9600 CR change RS232 speed rate to 9600 Key in lt 19200 CR change RS232 speed rate to 19200 PP Stands for control action code Key in lt 38400 CR change RS232 speed rate to 38400 PA PA control Key in lt 57600 CR change RS232 speed rate to 57600 PR Power control Key in lt 115200 CR change RS232 speed rate to 115200 MU Mute control DT DT control vo Volume control TR Treble control BS Bass control BL Balance control Key in lt 230400 CR change RS232 speed rate to 230400 When unplugging and re plugging the AC power cord the Baud speed rate will return to 9600 CH Source control LS keypad conne
10. 2 ZONE 3 ON JONPFF ONIOFFION ON OFFIOFA Each keypad must have a distinct address to communicate correctly with the controller amplifier Select zone address numbers 1 through 6 by using the chart ON 124112441128 to the right A DIP switch in the up position is ON a DIP switch in the down A H ZONE 4 ZONE 5 ZONE 6 position is OFF 123 JOFFJONJON FF ONDFF OFF OFH ON 12 3 123 1 2 3 NOTE When attaching AVTA 1 CE White and Green a keypad to an electrical 5 m7 PA 2 HH Green box use a screwdriver 3 CEM DI White and Orange to reduce the chance of 4 EEE Orange damage to the keypad 5 CI White and Blue da 6 EEE Bie PE ijo 2 D o Keypad O o NO Gn o O Keypad Hub daytonaudio com info daytonaudio com TT E Onono DAX66 INSTALLATION KEYPADS INSTALLATION Keypads Use high quality Cat5e 6 cable between the controller amplifier and the keypads Proper installation techniques will guarantee that the keypads will work properly up to 600 feet from the controller amplifier The use of terminal blocks on the keypads and keypad hub ultimately reduces the frustration associated with terminating UTP cable with RJ45 plugs The PCB is labeled 1 6 at t
11. MODE switch MONO to BRIDGE 1 E 8 ohm Gi speaker daytonaudio com info daytonaudio com DAX66 INSTALLATION PRE AMP OUTPUTS Using the DAX66 PRE AMP OUTPUTS The DAX66 provides six stereo unbalanced line level PRE AMP outputs which correspond to the six zone outputs The PRE AMP outputs can be used to connect powered subwoofers to a zone or additional amplifiers to expand the available power in a large zone or multiple zones The DAX66 can be used as the master controller in large commercial audio systems with constant voltage 25 70V amplifiers connected to the PRE AMP outputs The PRE AMP output levels are variable and are controlled from the DAX66 keypad Infrared remote or RS232 from an automation system For best performance the PRE AMP output cables should be less than 25 feet long and be high quality shielded cables J tS PRE AMP OUTPUTS wma 2 3 4 EXPANSION VOLJAGE SELECTOR e omrownj New ov Eu pam o gm 5 Om ee ni purs ZONE 3 ZONE 4 ZONE S ZONES ZONE ZONE2 ZONES SOURCE SOURCEZ SOURCES PAIN l JO L sprae oves HO O fu Mene 1206 TRIGGER OUTPUTS IR EMITERS SYSTEM DO
12. avronun 6 SOURCE 6 ZONE DISTRIBUTED AUDIO SYSTEM Model DAX66 User Manual SAFETY INSTRUCTIONS WARNING TO REDUCE THE RISK OF CAUTION TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT SHOCK DO NOT REMOVE THE COVER EXPOSE THIS APPLIANCE TO RAIN NO USER SERVICABLE PARTS INSIDE OR MOISTURE REFER SERVICE TO A DAYTON AUDIO AUTHORIZED DEALER IMPORTANT SAFETY INSTRUCTIONS e Read and keep these instructions Heed all warnings and follow all instructions contained within this manual Do not use this unit near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the unit Only use attachments accessories specified by the manufacturer Unplug this unit during lightning storms or when unus
13. cting status Reply command gt xxPPuu CR daytonaudio com info daytonaudio com DAX66 SPECIFICATIONS amp WARRANTY RMS Power 8 ohms 25 watts x 12 RMS Power 4 ohms 50 watts x 12 RMS Power 8 ohms Bridge Mode 100 watts x 6 SIN Ratio gt 85dB A Weighted THD lt 0 1 Frequency Response 20 20 000 Hz Input Impedance gt 47K ohms Input Sensitivity 250mv Amplifier Protection Overload Short Circuit amp Thermal Trigger Systems ON Voltage DC 12V Trigger External Mute Voltage DC 12V Infrared Frequency Band 38kHz Input Connectors 3 5mm stereo RCA Toslink Output Connectors Terminal Block RCA Power Supply switchable AC115V 60Hz 230V 50Hz Dimensions 16 9 W x 3 5 H x 16 4 D Weight 24 25 lbs Warranty 5 Years daytonaudio com Specifications are subject to change from time to time Without notice Contact Information Dayton Audio 705 Pleasant Valley Drive Springboro OH 45406 PH 937 743 8248 E Mail info daytonaudio com Web www daytonaudio com Warranty This Dayton Audio product is warranted free from defects in material and workmanship for a period of five years from date of purchase Product registration is not required however keep the original invoice as proof of purchase Warranty does not apply to misuse abuse neglect accident improper use etc To process a ret
14. ed for long periods of time Refer all servicing to qualified service personnel Servicing is required when the unit has been damaged in any way such as when the power supply cord or plug is damaged liquid has been spilled or objects have fallen into the unit the unit has been exposed to rain or moisture does not operate normally or has been dropped Operate the unit only with the voltage specified on the rear Fire and or electric shock may result if a higher voltage is used Do not modify kink or cut the power cord Do not place the power cord in close proximity to heaters and do not place heavy objects on the power cord and or the unit itself doing so may result in fire or electrical shock Do not touch the speaker terminals as electric shock may result Ensure that the safety ground terminal is connected to a proper ground Never connect the ground to a gas pipe as a severe explosion and or fire may result Be sure the installation of this product is stable avoid unlevel surfaces as the product may fall and cause injury property damage electrocution and or fire Note that when the unit is turned off it is not completely disconnected from the AC power outlet Do not open the cover REFER ALL SERVICE TO A QUALIFIED SERVICE TECHNICIAN daytonaudio com info daytonaudio com PRODUCT OVERVIEW Congratulations on your purchase of the Dayton Audio DAX66 6 Source 6 Zone Distributed Audio System You have chosen a unit that provides the
15. ends 12Vdc to the trigger output jack When the zone is powered OFF 12Vdc is disconnected from the trigger output The triggers can be used to automatically switch peripheral equipment ON OFF The DAX66 also provides a master control 12Vdc trigger output that sends 12Vdc to the CONTROL OUT jack when any zone is powered ON and disconnects the 12Vdc when all zones are powered off DAX66 Trigger outputs ZONES 1 6 Zone ON 12Vdc applied to the TRIGGER OUTPUT Zone OFF 12Vdc removed from the TRIGGER OUTPUT CONTROL Any zone ON 12Vdc applied to the CONTROL OUT All zones OFF 12Vdc removed from the CONTROL OUT DAX66 Trigger Inputs PA IN Apply 12Vdc for input 1 override on all six zones MUTE IN Apply 12Vdc to mute all zones PREAMP OUTPUTS Pa 2 3 a s eeeansion o oem e e ongownj aim Ta ENI 25 232 E meurs ZONE 3 ZONE 4 ZONE 5 ZONE 6 SMEJ ZONE ohra Eis l l al a nl oa db dono Bono El External Amplifier Control To Projection E EEE Screen 12 Vdc To External 2 saueue pansan O gt Trigger In Amp
16. er speaker installation can damage the amplifiers and void the warranty If you are unsure how to connect speakers to the DAX66 contact a qualified technician Remove the terminal block connector and make sure that all contacts are open by turning each set screw counter clockwise This helps insure that the speaker wire will not fray when inserted into the terminal INSTALLATION Connecting 8 ohm speakers to the DAX66 in STEREO MODE Set the amplifier mode switch to STEREO Remove approximately 5 inches from the cable jacket strip 1 4 of insulation from the speaker wire and twist the copper strands Insert the speaker wires into the connector per the label below the output terminals and tighten the set screws Repeat for the remaining zones EXPANSION 6 bavronauog VOUAGE SELECTOR vom PATO ie o am ah e He Q q CED A sla Ke Es ZONE nl zoles AT TONE ZONES SOURCE SOVRCEZ souces PAN e l l L seenen cus l l OJO 0100 no zal re o o 0 sto i E E E 0 0 0 ols ek i het in ti ri cons Lun cito FECE RAS E
17. he location corresponding to the terminal blocks Attach the conductors in the same order on each end of the cable See illustrations on the previous page Strip the insulation from the UTP Cat 5e cable about three inches Don t be concerned that too much insulation has been removed since the wire will be hidden in the wall behind the keypad Remove approximately 1 4 of insulation from the conductors and insert into the terminal block Tighten the screw terminal on the block to hold the wire in place Do not over tighten the screw to avoid stripping out the terminal Attach the terminal block to the mating connector on the keypad or the keypad hub Use standard electrical boxes or low voltage rings to mount the keypads and keypad hub Mount the keypad hub less than 7 10 feet from the controller amplifier Connect the keypad hub to the master controller amplifier using a standard Ethernet patch cable NOTE Always follow local building codes and use proper electrical boxes and low voltage rings Cat5e 6 9 8 7 10 feet o alo EXPANSION VOUAGE SECTOR LU tai e M
18. lifier 12VDC Trigger In comum o Di OO ie WIRING 3 5mm Mono Motorized Projection Screen plug lip Positive O E 5 daytonaudio com info daytonaudio com DAX66 INSTALLATION EXPANSION Expanding the DAX66 to 18 zones The DAX66 can be expanded to 12 zones with one additional DAX66 kit and to 18 zones with two additional DAX66 kits Stack three DAX66 one on top of another Connect the included 18 pin ribbon cable to the EXPANSION OUTPUT terminal of the bottom unit and the other end of the ribbon cable to the EXPANSION INPUT terminal of the second and then third unit Set the MASTER SLAVE 1 SLAVE 2 switch of the bottom unit to MASTER the center unit to SLAVE 1 and the top unit to SLAVE 2 The following data and control is transmitted between the three units all source audio all RS232 control data and all MCU communication data SLAVE 2 SLAVE 1 MASTER oe o eejo t eloelo AO 510000 di T zonta o e 8 6
19. o com DAX66 INSTALLATION OVERVIEW Install the DAX66 in a well ventilated location do not block the vents on the sides or top of the chassis proper ventilation is required for normal operation Do not expose the unit to excessive dust and do not allow dust to build up on the unit and block the vent holes in the chassis Do not place the DAX66 above or below heat generating components such as another audio amplifier Be sure to leave at least 2 inches of space to the sides of the chassis with open air flow above and below the unit Due to the weight of the unit we recommend using four post racks at minimum OVERVIEW 1 The DAX66 can be mounted in an equipment rack using the included rack mount kit 2 Always disconnect AC power before making connections to the DAX66 3 Use good quality 12 or 14 AWG stranded copper speaker wire for all speaker connections 4 Use good quality cable for connection of the keypads to the master controller amplifier we recommend Cat5e to connect keypads 5 The DAX66 uses a keypad hub all keypads will connect to the hub Install the keypad hub close to the master controller amplifier For ease of installation the keypads and the keypad hub are fitted with quick disconnect screw terminal blocks 6 The keypad hub connects easily to the master controller amplifier using a standard Ethernet patch cable NOTE Set the Address of each keypad using the DIP switches on back of the keypad ZONE 1 ZONE
20. ultimate audio control in six stereo zones expandable to 18 stereo zones The DAX66 is a true matrix audio system that delivers an extensive list of features for professional and residential installations The DAX66 was designed for ease of installation by the integrator and to be simple to operate for the user The DAX66 provides six analog line inputs and one Toslink S PDIF digital audio input Play music from CD DVD satellite or cable box PC or personal audio device The RS232 interface allows an automation system to manage and control the DAX66 Built in IR repeater provides a path to control source devices through the IR target in the keypad Operates with 4 8 ohm speakers in stereo mode 8 ohm speakers in bridged mono mode and provides a generous level of output power Please read and retain this manual to get the most from your Dayton Audio DAX66 6 Source 6 Zone Distributed Audio System The DAX66 kit includes the following parts 1 x Master Controller Amplifier 2 6 x Keypad Controllers 3 1 x In Wall Keypad Hub Connection Plate 4 1 x Infrared Remote Control 5 6 7 1 x Expansion Ribbon Cable 1 x Rack Mounting Kit 1x Installation Guide Operation Manual DAX66 MASTER CONTROLLER AMPLIFIER FRONT O O omrowund f E 7 i o o o o o o pe o o o o o o STANOSY ON STANDBY ON STANDBY ON STANJBY ON STANDEY ON STANDEY ON O DAXSS 6 SOURCE 6 ZONE DISTRIBUTED AUDIO SYSTEM O Power On Off
21. unit 1 Zone3 of Main unit 1 Zone3 of Main unit 1 s Zonel of Main unit 2 PP Zone2 of Main unit 2 PR Power control Zone3 of Main unit 2 PROO Power off PR0l Power on MU Mute control Reply command gt xxaabbceddeeffgghhiijj CR MUOO Mute off MUO1 Mute on aa PA control status DT Do Not Disturb control bb Power control status 5 Backup Zone Power DT00 DT control off Status DTO1 DT control on only on zone VO Volume control cc Mute control status VO 00 38 Volume control dd DT control status TR Treble control ee Volume control status TR 00 14 Treble control ff Treble control status BS Bass control gg Bass control status BS 00 14 Bass control BL Balance control BL 00 20 Balance control daytonaudio com info daytonaudio com DAX66 INSTALLATION RS 232 CONTROL DAX66 RS 232 Serial Port Control con hh Balance control status ii Source control status jj keypad connecting status 00 disconnect 01 connected Inquiry command structure 2 xxPP CR xx stands for control object code 10 All Zone of Main unit 1 20 All Zone of Main unit 2 30 All Zone of Main unit 3 11 Zonel of Main unit 1 12 Zone2 of Main unit 1 13 Zone3 of Main unit 1 14 Zone4 of Main unit 1 15 Zone5 of Main unit 1 16 Zone6 of Main unit 1 PP Stands for control action code PA PA control PR Power control MU Mute control DT DT control vo Volume control TR Treble control
22. urce selection LED Down volume treble bass un mute Treble up down LED Bass up down LED Up volume treble bass un mute Source select 1 6 descending Source select 1 6 ascending Power ON OFF amp mode select Press and hold for zone on off press to toggle through volume source treble and bass adjustment mode Use the select button with the volume up down buttons to adjust volume levels treble and bass levels Infrared IR target The select button emits a soft glow when the zone is powered off daytonaudio com info daytonaudio com DAX66 INFRARED REMOTE CONTROL FEATURES The DAXRC infrared remote control provides complete zone control through the IR receiver located on the DAX66 keypad All keypad functions can be accessed using the DAXRC In addition to the keypad functions the DAXRC has a MUTE button to temporarily mute audio in the zone Once the MUTE function is activated the keypad s LED display will flash indicating the mute status Press the MUTE button to continue playing music or press the keypad volume up or down buttons to un mute the zone One DAXRC is included with each system and additional DAXRC are available from your Dayton Audio dealer Infrared IR Emitter Mute Zone power ON OFF Source toggle 1 6 Treble up down Bass up down Volume up down Balance left Balance right Balance Balance pmrowund daytonaudio com info daytonaudi
23. urn or have your product replaced under warranty please contact your Dayton Audio reseller to to obtain an RA Pack merchandise carefully to avoid further damage and complete the Return Form on the bottom of the invoice Record customer and RA numbers on the outside of the box Ship merchandise back to your Dayton Audio reseller prepaid 2014 Dayton Audio all rights reserved All trademarks are the property of their respective owners Specifications are subject to change without notice Dayton Audio cannot be held liable for typographical errors or omissions info daytonaudio com Dayton Audio Last Revised 4 20 2015
Download Pdf Manuals
Related Search