Drum Mower User`s Manual
Contents
1. Sa FiMAKS DRUM MOWER USER S MANUAL APPENDICES 01 INDEX 02 INTRODUCTION 03 MACHINE DIMENSIONS 04 WORKING AND TECHNICAL SPECIFICATIONS A WORKING SPECIFICATIONS B TECHNICAL SPECIFICATIONS 05 MAIN INFORMATIONS FOR MACHINE 06 THE MATTERS BEING CAREFUL DURING TRANSPORT 07 ASSEMBLY AND WORKING A ASSEMBLING OF MACHINE B SAFESTARTUP C CHANGING CUTTERS 08 OPERATING INSTRUCTIONS FOR SAFETY 09 MAINTENANCE INSTRUCTIONS 1 DAILY MAINTENANCE 2 ANNUAL MAINTENANCE 02 INTRODUCTION Drum mower is a kind of grass cutting machine which moved from tractor back pivot axle free rotary cuttered and can be hanging type 03 MACHINE DIMENSIONS 04 WORKING AND TECHNICAL SPECIFICATIONS A WORKING SPECIFICATIONS It cuts the crops requested height through cutters are located on reverse rotary pulleys and it has 4 times powered work value than its equal typed machine The biggest characteristic is putting down the crops over the floor regularly even by lower powered tractor and even if the crops are wet or bended through clearing drum dimensions and available free revolving of bottom ashtrays B TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS MODEL TYPE ST165 PULLEY NUMBER 2 CUTTER NUMBER 6 and 8 CUTTING WIDTH 165cm BACK PIVOT AXLE REVOLUTION 540 rom PULLEY REVOLUTION 1920rpm REQUIRED TRACTOR OUTPUT POWER 25 HP TOTAL WEIGHT 370kg 05 MAIN INFORMATIONS FOR MACHINE It is connected with a t2. 182 ST 183 gt Ref Description Protection Cover Bo f Strip for Protection Guard Guard Tube Nut Protection Guard Code ST 184 ST M3 8x20 ST 185 ST 186 ST M3 8 ST 187 Quantity 1
3. inside lag and outside of tractor rear right wheel and tighten strength bars Right bottom connection bar must be as obtain that cutters are parallel to earth Follow same way before machine start up al N 2 A A HR Al 2 7 HA S R S 192 199 AI O IBA gt N 4 N E IN 1 9 R N 4 hr 4 3 4 S 4 D US Lj SN up 1 2 PAL lt lt 1 84 N NS Y ed gt POSITION 1 Take the machine right position Approach the tractor to machine Connect the machine to tractor with three point after distance is adjusted Connect the clutch of shaft to tractor pivot axle POSITION 2 Open the pad lock after machine fix to tractor Obtain the back movement of tractor for cutting position POSITION 3 When the angle is 90 between machine and tractor that mean is cutting position fix it for cuffing position as automatic arm interlaces pad pin B SAFE START UP Before using machine the oil named SAE 140 must be filled up to not overflow from container which the plug near of gear box At the end of each cut of grass machine must be cleaned controlled oil lever kept in a suitable place The cutters of disks must not be missed Always equal sized cutters must be used for machine If cutter sizes are different the balance of disks can be spoil
4. 02 ST M10x25 ST M10 ST 103 ST 6305 2RS ST 104 ST 105 ST 25x2 ST 30x1 5 ST 106 ST 107 ST 30x0 25 ST 6206 2RS ST 108 ST 109 ST 110 ST 28x2 ST 111 ST 112 ST 113 ST 114 ST 115 ST 24x1 5 ST 116 ST 117 ST 45x62x8 Quantity 20 00 22 emniyet lamas arkadan g r n amp ao dol NO Description Nut Muhafaza Baglanti Vidasi Pin Bolt Nut Lid for Pui ey Guard Pulley Guard Bolt Lift Link Grease Nipple Spacer Nut Sub frame Transport Tube Jack Stand Nut Pin Slide for Breakaway Spring Washer Bolt Cotter Pin Tab Washer Bolt Bolt Ana Govde Baglanti Kolu Spring Clip Code ST M10 ST 118 ST 119 ST M10x25 ST M10 ST 120 ST 121 ST M16x35 ST 122 ST 5 16 ST 123 ST M16 ST 124 ST 125 ST 126 ST 1 2 ST 127 ST 128 ST 129 ST 130 ST 1 2x175 ST 4 30 ST 131 ST M16x30 ST M16x45 ST 132 ST 133 Quantity n aa e 00 Ref Description Lift Link Ana Govde Baglanti Borusu Lift Pivot Bracket Spacer Bolt Spring Cap Lift Link Cotter Pin Washer Spacer Pin 8mm Yayli Pim Kot Pimi Kol Pimi Circlip Washer Pivot
5. Sleeve Hitch Frame Pin Pin Cotter Pin Nut Lock Lever Bolt Code ST 134 ST 135 ST 136 ST 137 ST M10x85 ST 138 ST 139 ST 140 ST 4x30 ST 141 ST 142 ST 143 ST144 ST 145 ST 146 ST 60x2 ST 147 ST 148 ST 149 ST 150 ST 151 ST 152 ST 6 60 ST M10 ST 153 ST M10x75 Quantity AN ANDAN AH NO AH HAH NY AHN HH AH AN A Ref Description Shaft Small V pulley V belt Washer Nut Tension Bolt Nut Tab Washer Large V pulley Ball Bearing Tab Washer Drive Shaft Key Spacer Housing Cotter Pin Pin Code ST 154 ST155 ST 17x2850 ST156 STM16 ST 158 ST 30x1 5 ST159 ST160 ST 6207 ZZ ST 161 ST162 ST 163 ST164 ST165 ST 4x30 ST 166 Quantity dh Al td SP OO St gt ii IG T SO 24 Description Alien Screw Saucer Blade Percin Blade Holder Drum Bijon Hub Ball Bearing Ball Bearing Dokum Rulman Yatagi Celik Tas 3 mm Klip Spring Clip Hub Nut Tab Washer Bevel Pinion Oil Seal Circlip Ball Bearing Drum Shaft Ball Bearing Circlip Key Key Code ST 10 30 5 167 ST 168 ST 169 ST 170 ST 171 ST 172 ST 173 ST 6210 2RS ST 51109 ST 174 ST 175 ST 176 ST 177 ST 178 ST 24 15 ST 179 ST 180 ST 40x62x10 ST 62x2 ST 6305 ZZ ST 181 ST 6207 ST 35x2 5 ST
6. hree pointed hanging system to tractor and it is specified as pulleyed rotary cuttered free cutting possibility There are three pointed hanging system gear box V belt pulley system two of cutter pulley 6 of leaf cutter jointed axle to move carrying bars connected to three pointed hanging system and carrying chassis on the Drum Mower The machine is designed as two different chassis Both three pointed hanging system and belt pulley system from the first chassis of the machine The gear box is the second chassis which bear the drums at the same time The gear box and first chassis are connected to each other with two piece of slider bearing by the side of machine The drum activate to gear is formed by bearing Furthermore two of chassis are connected to three pointed hanging system with two of parallel steel bar which has spring pressed and this causes to adjust the length of machine The drum mower is activated from upper side of machine The first movement is transmitted from tractor back pivot axle to three grooved V belt pulley system then it is transmitted to gear box and pulley axle through gears and last of all movement is transmitted to cutter disks At the first step movement is transferred with belt drum system and at the second step it is transferred to gear box then to cutter disks Fill up the gearbox with suitable oil Oil leakage is obtained with a joint There are double of gear which increase the movement comes from dru
7. ing operation 11 Use original cutters if olds are not run well 12 Do not approach to machine without stopping the tractor 13 Keep the machine transfer position when you do not use it 14 Do not allow the persons to approach to machine because the machine can throw some stones or hard things to people 15 Before cutting operations the field or area must be cleaned from stones or hard things These can damage the machine 16 Take care when you work in path or stony roads 09 MAINTENANCE INSTRUCTIONS 1 DAILY MAINTENANCE a Use the lubricating grease after every cutting operation b Check the cutters and belts after cutting operations 2 ANNUAL MAINTENANCE a Make a general cleaning at the end of reaping season b Check the all parts of machine Renew the damaged ones or unusable ones c Use the lubricating grease to lubricate all of lubricating hole d Keep the machine in a covered place after cleaning amp PO PO POP HH BH Y Description Bolt Spacing Tube Plug Alien Screw Nut Key Ball Bearing Spacing Tube Bevel Gear Circlip Nut Tab Washer V pu ley Raynel Ball Bearing Spacing Tube Bevel Gear Segman Yatagi Circlip Input Shaft Key Rulman Yatagi Bevel Gear Tab Washer Nut Drive Shaft Main Frame Oil Seal Code ST M10x25 ST 101 ST 1
8. m and two of double gear which transfer the movement to cutter disks in the gear box There are totally three double gears in the gear box 4 The movement is transmitted to conical gear of second drum by a metal bar dimensioned as 1070mm 25 mm This metal bar is beared as three point over it The conical gears are settled reverse sided on that metal bar So there is designed a grass barrel on the middle of the system There are spring pressed cutter on each of disks Both two side of cutter has cut featured The cutter can be use for others when it wears because of disks revolve opposite side The cutters can be changed easily with a special spanner without disks pull out The working safety of drum mower is kept with spring pressed safety system Also there is a spring safety coupling in main axle which movement transmitted from tractor pivot axle 06 THE MATTERS BEING CAREFUL DURING TRANSPORT The machine must be kept from hard blows and frictions during transport The machine must be fix to flour to not move during transport 07 ASSEMBLY AND WORKING WITH THE MACHINE A ASSEMBLY Bring the tractor near machine to fix all parts of machine Firstly fix left bottom connection bar secondly right bottom connection bar then the top connection bar to machine Lift up the support leg of machine and loose strength bar of tractor Take down the machine on a smooth place as being 5 cm diameter between continuation of middle point of
9. t can cause breakdown and machine life can be decrease Keep the tractor revolution lower at the first start up After than increase the revolution up to max 540 rpm Set the forward speed according to situation of crop and field If disks experience any difficulty that cause to readjust strength for working situation so stop the tractor immediately in this condition and get speed gear empty position Abolish the difficulty and set the machine to start up again C CHANGING CUTTERS The wore cutters can be change easily with a cutter dismantle spanner It must be lifted up to cutter fix pin gets free when the cutters dismantled When mantle of new cutters be careful to be cutting side is bottom 08 SAFE OPERATING INSTRUCTIONS 1 Stop the machine when setting and oiling 2 Change the plastic protection of shaft if it is damaged 3 Put on extra weight on the front of the tractor to balance between front side and rear side 4 Put on the protection screen before the cutting operation 5 Put on the shaft protection chain to side lifting bar so shaft would not be turn because of protection 6 Get the machine parallel to earth before start up 7 There must not be any living creature between tractor and machine to start up machine 8 Turn the machine to side after machine is parallel to earth 9 Do not over revolution as 540 rpm as stated in operating instructions 10 Be careful that cutters are true settled after chang
Download Pdf Manuals
Related Search