Single and triple channel video only link
Contents
1. 1M LASER DIODE DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTI CAL INSTRUMENTS APPLICABLE STANDARD IEC60825 1 2001 The CRT103 is a three channel optical transmitter for uni directional video transmission in a multimode fibre The current consumption is 300 mA 12 VDC Frame Installation The CRT103 module is to be pushed along the guide rails into the installation frame e g CSR216 or 316 series and secured with the two locking screws The unit can be freely positioned in any slot in the frame The empty positions in the frame should be blanked off with cover plates The supply voltage is to be provided by a CPS384 or CPS390 power supply unit which are installed back of frame Stand alone Installation The unit can be installed for stand alone use by using a CMA011 module adapter The module should be mounted to a vertical surface The 12 VDC supply voltage is supplied by the means of a separate mains adapter with a regulated output e g CPS221 The permitted supply voltage range is 10 5 14 VDC The current consumption is 300 mA The permitted operational temperature range is from 34 74 C Video connections CRT103 5 OPTICAL TRANSMITTER EEE The impedance of the video inputs BNC female is 75 Q The nominal input level is 1 Vpp CRT103 Optical Transmitter 1 Locking screw 2 pcs 2 Video input BNC female 3 Optical output ST Link status indicator LEDs In the u2. The permitted supply voltage range is 10 5 14 VDC The current consumption for CRR101 is 130 mA and for CRR103 300 mA The permitted operational temperature range is from 34 74 C Video connections and indicator LEDs The impedance of the video outputs BNC female is 75 Q The nominal output level is 1 Vpp Link status indicator LEDs When the optical input signal level is adequate and syncronization on link level is achieved the LINK STATUS led on the front panel is green If optical input signal is missing or it s level is too low the LINK STATUS led is yellow CFO100 Digital Series user manual rev001 top view ST Connectors Make sure the key is aligned in the slot properly before tightening CFO100 Digital Series user manual rev001 Fibre connection The optical connector is of the type ST Minimum optical intput level is typically 23 dBm No adjustments for input are needed The operating wavelenght is 1310 nm When installing the fibre optic cable do not exceed the minimum bending radius when connecting cable to the system Note For correct optical operation ensure that all optical connec tors are cleaned immediately before mating Connectors should always be cleaned using high purity alcohol e g methyl or isopropyl alcohol Dry the surfaces using clean compressed air or other equivalent pressurised gas The female ST optical connec tors on the equipment should always be protected with dustc
3. within the specified temperature power supply and duty cycle ranges CRR101 103 Single and triple channel video receiver CRR103 5 OPTICAL RECEIVER SO CRR103 Optical Receiver 1 Locking screw 2 pcs 2 Video output BNC female 3 Optical input ST 4 Link status indicator led 5 Handle with unit information See further information on dedicated sections Note CRR101 is a single channel version of CRR103 The CRR101 is a one channel optical receiver for uni directional video transmission in a multimode fibre The current consumption is 130 mA 12 VDC The CRR103 is a three channel optical receiver for uni directional video transmission in a multimode fibre The current consumption is 300 mA 12 VDC Frame Installation The CRR101 103 module is to be pushed along the guide rails into the installation frame e g CSR216 or 316 series and secured with the two locking screws The unit can be freely positioned in any slot in the frame The empty positions in the frame should be blanked off with cover plates The supply voltage is to be provided by a CPS384 or CPS390 power supply unit which are installed back of frame Stand alone Installation The unit can be installed for stand alone use by using a CMA011 module adapter The module should be mounted to a vertical surface The 12 VDC supply voltage is supplied by the means of a separate mains adapter with a regulated output e g CPS221
4. Typical values unless otherwise stated 4 65 dB weighted BNC female Video Video CRR101 CRR103 CRR103 multimode fibres p to 6 5 km Video Video Video Video Video Video multimode fibres up to 6 5 km Video Video CRT103 Video multimode fibres p to 6 5 Km Video Video Video CFO100 Digital Series user manual rev001 Copyright acknowledgements Information in this document is subject to change without notice and does not represent a commitment on the part of Teleste Corporation Copyright Teleste Corporation All Rights Reserved No part of this document may be reproduced transmitted stored in a retrieval system or translated into any other language without the express permission of Teleste Corporation Teleste Corporation Video Networks P O Box 323 FIN 20101 Turku FINLAND www teleste com WEEE directive Directive 2002 96 EC of the European Parliament and of the Council on waste electrical and electronic equipment WEEE obliges that producers appropri ately mark electrical and electronic equipment with the symbol indicating separate collection This obligation applies to the equipment put on the market in EU after 13 August 2005 Teleste devices which belong to the scope of the directive have been marked with the separate collection symbol shown below The marking is according to the standard EN 50419 The symbol indicates that the device has to be collected and treated sepa
5. User Manual Single and triple channel video only link CFO First Mile series consist of fibre optic modems which 2 provide a high quality and losless video transmission for variety of CCTV applications over multimode fibre OPTICAL RECEIVER Video Networks CFO100 Digital Series user manual 59300292 rev001 Contents CFO100 Single and triple channel video only link uuuusnn n0nnnonnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnannnnnnnnnnnnn nun E Mpeg te a raioane iata aan e ae fii aa an du ER ei ata dora n ai aaa ER EHER ta ENTER FOUE S sint ineaca deea ada a aa a i ata na up n dt t alea a ta CPT101 Mini sized stand alone video transmitter eu s 0n0nn0nannnn nn nan nn nnn nun an nun nn nun nn nun nun ma na mana nana na nana GENE A nee m iti ai atu cere ia a einen TOE ehesten VOGO 9 8 0 ea ee iad i ete alti dani arat ia at ia DIDI COMME COLON aaa ee tea i legi isa elan aut aa as E tn dna iai deea aaa stand alone Ca EI OEI seen tan aul ia idea tu CRT103 Triple channel video transmitter ee eee neoane ee nenea nenea menee nenea nenea nenea nenea nenea nnnnnea nenea nenea nenea GENE scoata iat dia roi nalt pacii aa nainte aan e b i d at bea nada tea a ba iai dia Frame BENS eV Tl Oi sie iii ca ia ta aa ai oi na il acu e tiu ai etno aia a Stand alone Installation Video COHNEEUON Se ee aa it ara ri alta ie aia ai a m i ae a ata va Lk Stats mdicator ED Scot cane nestiinta le c
6. a to a monitoring centre DIGITAL CFO100 series consist of mini sized stand alone video trans mitter followed by standard 5HP size CFO cards for triple channel video transmitter as well as for single and triple channel receiver operation The CPT101 stand alone transmitter is temperature hardened and is capable of using both 12 VDC or 24 VAC supply voltage CPT101 unit is a compact size housing for special stand alone installations requiring minimal installation space Also as an optional DIN rail mounting is possible item code CIK001 CRT103 and CRR101 103 cards are compatible with all CFO rack systems Stand alone options are available with the CMA011 module adapter and separared CPS series mains adapter As with all CFO platform products these specific models do meet all typical EMC as well as other environmental and manufacturing related requirements The permitted operational temperature range is 34 74 C Note New generation CFO100 products are based on digital transmission and are not therefore compatible with previous analog 100 series gt gt Low cost video transmission gt gt High performance uncompressed zero delay digital video transmission SNR 65 dB typical 10 bit video sampling gt gt One CVBS PAL NTSC video channel gt gt Transmission over on one or three multimode fibre up to 6 5 km gt gt Card format applicable both for rack mount and stand alone installations gt gt One and triple channel un
7. aps when there is no fibre inserted Optical connection meets class 1M laser safety requirements of IEC 60825 1 2001 and US department of health services 21 CFR 1040 10 and 1040 11 1990 when operated within the specified temperature power supply and duty cycle ranges Technical Specifications Optical Wavelength Output power Input sensitivity Bit rate Link distance Optical connector Video Number of channels Standard Input level Input overload level Impedance Sampling resolution Sampling rate Bandwidth Insertion gain C L gain inequality C L delay inequality Differential gain Differential phase SNR Video connector General 1310 nm multimode fibre Supply voltage 10 5 14 VDC regulated 4 dBm max 16 28 VAC CPT101 25 dBm max Current consumption max 130 mA CPT CRR101 200 Mbps 300 mA CRT CRR103 6 5 km max Power supply connector 2 pin screw terminal CPT101 ST Dimensions H x W x D CRT103 amp CRR101 103 3U 5HP 190 mm without CMA CPT101 25 48 62 mm without connectors 1 uni directional CPT CRR101 Weight 0 2 kg CPT101 3 uni directional CRT CRR103 0 5 kg CRT103 amp CRR10x PAL NTSC CVBS Alarms indicator LEDs 1 Vpp Link status LED CRR101 103 1 75 Vpp Power LED CPT101 CRT103 75 ohm Operating temperature 34 74 C 10 bit Storage temperature 34 74 C recommended 20 0 MHz Humidity 0 95 non condensing 8 MHz 1 dB EMC compatibility EN61000 6 3 1 dB EN50130 4 CE 4 AO ns Notes 2
8. ea avea ne tea at ie aul aa tt at Fibre connection CRR101 103 Single and triple channel video receiver mcnn enron enaea nenea nenea nea anno oneanennananeaas CO CINE AL stiau donat d iarta daia aa ada ia anii ue uta et d a at bena ab te a bage ii Frame Installation aia ia ta aa ai oi na il acu e neti ai tn iai Stand SOS UT tala ON se ci e soarele daia ate date bla lac aia el i aliati ia a ai od dili au Video connections and indicator LES estuar ea ae nee EINK S ALS indicator LEDS PR RR RR ec RI RN RR see CR CER NI IRI RR NI ANII DR O INI ee Fibre connection Technical Specifications vases ataca bon aa aa cinta een lili a e ta ta iai anal i di ai li aia Copyright acknowledgements 2 nenn ee ee ea iai te WEEE directive CFO100 Digital Series user manual rev001 CF0O100 Single and triple channel video only link CFO100 Digital First Miles series offers a 10 bit video transmission over one mutimode fibe video channel for fixed camera applications VV Vv gt CFO100 Digital Series user manual rev001 Welcome and thank you for purchasing Teleste s CFO Products DIGITAL CFO100 First Mile series offers a highly cost effective single channel composite video transmission over one multimode fibre High quality video image can be transmitted over distances up to 6 5 km depending on the type of multimode fibre in use A typical application is a point to point transmission from a fixed CCTV camer
9. its available for both transmitter and receiver gt gt Transmitter unit available in a special compact size stand alone design gt gt Feasible for field hardened operation gt gt Mechanically compact and ruggedised gt gt EMC and environmental conformance CPT101 Mini sized stand alone video transmitter side view CPT101 Digi Pixi CPT101 Optical Transmitter 1 Video input BNC female 2 Optical output ST 3 Power led 4 Power supply connector 2 pin screw terminal 5 Grounding top view 4 7 Loy iil ST Connectors Make sure the key is aligned in the slot properly before tightening CAUTION THESE OPTICAL UNITS USES CLASS 1M LASER DIODE DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTI CAL INSTRUMENTS APPLICABLE STANDARD IEC60825 1 2001 The CPT101 is a one channel optical transmitter for uni directional video transmission in a multimode fibre The current consumption is max 130 mA 12V DC Video Input The video input impedance BNC female is 75 O The nominal input level is 1 Vpp Fibre connection The optical connector is of the type ST The optical output level is typically 4 dBm For testing purposes the CFO100 series transmitter and receicer can be connected with a short fibre patch cable The operating wavelenght is 1310 nm When installing the fibre optic cable do not exceed the minimum bending radius when connecting cable to the sys
10. ni directional CRT103 units the LINK STATUS led is only monitored by the optical receiver CRR101 103 Therefore the LINK STATUS led in CRT103 units has no real value and is always green 4 Link status indicator led 5 Handle with unit information See further information on dedicated sections 4 CFO100 Digital Series user manual rev001 top view ri 47 ST Connectors Make sure the key is aligned in the slot properly before tightening CFO100 Digital Series user manual rev001 Fibre connection The optical connector is of the type ST The optical output level is typically 4 dBm For testing purposes the CFO100 series transmitter and receicer can be connected with a short fibre patch cable The operating wavelenght is 1310 nm When installing the fibre optic cable do not exceed the minimum bending radius when connecting cable to the system Note For correct optical operation ensure that all optical connec tors are cleaned immediately before mating Connectors should always be cleaned using high purity alcohol e g methyl or isopropyl alcohol Dry the surfaces using clean compressed air or other equivalent pressurised gas The female ST optical connec tors on the equipment should always be protected with dustcaps when there is no fibre inserted Optical connection meets class 1M laser safety requirements of IEC 60825 1 2001 and US department of health services 21 CFR 1040 10 and 1040 11 1990 when operated
11. rately from unsorted municipal waste User manual revision history note The latest version is always available in pdf format on our web site www teleste com CFO100 Digital Series user manual rev001 TELESTE www teleste com
12. tem Note For correct optical operation ensure that all optical connec tors are cleaned immediately before mating Connectors should always be cleaned using high purity alcohol e g methyl or isopropyl alcohol Dry the surfaces using clean compressed air or other equivalent pressurised gas The female ST optical connec tors on the equipment should always be protected with dustcaps when there is no fibre inserted Optical connection meets class 1M laser safety requirements of IEC 60825 1 2001 and US department of health services 21 CFR 1040 10 and 1040 11 1990 when operated within the specified temperature power supply and duty cycle ranges CFO100 Digital Series user manual rev001 Stand alone Installation The CPT101 units are designed for stand alone installation The unit should be mounted with a help of wall bracket to a installation place The supply voltage can be either 12V DC or 24V AC The supply voltage is provided by either a surveillance camera unit or by an external mains adapter The permitted supply voltage range are 10 5 14 VDC and 16 28 VAC In DC use the 12V DC supply voltage is supplied by the means of a separate mains adapter with a regulated output e g CPS231 The permitted operational temperature range is from 34 to 74 C 18 4 Wall bracket dimensions CFO100 Digital Series user manual rev001 3 CRT103 Triple channel video transmitter CAUTION THESE OPTICAL UNITS USES CLASS
Download Pdf Manuals
Related Search