DVR User Manual
Contents
1. 2 4 5 3 Video loss Pic 2 19 Video loss Click alarm handling button turn to window as below Alarm Handling Alarm Pic 2 20 Video loss alarm handling The setup steps of video loss trigger are familiar with alarm handling User can also setup all channels with same parameters click Apply button to save the setting click Exit button to exit current interface Click Default button to resort default setting Disconnected from the network when the network connection is disconnected the system will automatically sent E mail to the user specified mailbox about the network disconnected 2 4 5 3 Alarm out The hardware does not support 2 4 6 Network configuration Network configuration includes four submenus network sub stream Email and other settings 2 4 6 1 Network 18 SS E E DECKER Se Pic 2 21 Network configuration HTTP port the default value is 80 If the value changed user needs to add the port number when typing IP address in IE address blank IE set HTTP port to 82 IP address http 192 168 0 25 user needs to input that address http 192 168 0 25 82 into IE browser Server port data and image communication port NO After selecting the Obtain an IP address automatically the device will distribute IP address subnet mask and gateway IP and DNS server Enable PPPoE to directly connect the DVR to internet via ADSL and then input the user name and password clic2. 2 4 8 1 serial port Pic 2 28 Serial port Click Start base on P T Z support Protocol to set Address Baud rate and Protocol User can setup all channels with same serial port parameters please tick off All and then to do relevant setup click Default button to resort default setting click Apply button to save the setting click Exit button to exit current interface Definitions and descriptions of serial port Baud rate Baud rate of the PTZ device Range form 110 300 600 1200 2400 4800 9600 19200 38400 57600 115200 230400 460800 921600 Protocol Communication protocol of the PTZ device Range from PELCOP PELCOP1 PELCOP5 PELCOD PELCOD1 HY PHILIPS SAMSUNG SHARP SONY SAMSUNG PANASMIC Control etc 2 4 8 2 Advance configuration Advanced Pic 2 29 Advance 22 SE In the Advance interface after clicking preset Setting button a dialog box will pop up as below Pic 2 30 Preset point setting In the preset set interface click Setting button to see a window as below Pic 2 31 Preset setting User can control the P T Z up up left down right down left left down right and up right and stop rotating can adjust the rotation speed of the PTZ focus focus and aperture choose preset arrange NO Click Save button to save the settings click al icon to hide the tool bar right key can remerge it click icon to exit the current interface In the
3. Main Menu Tr B S Data Backup ee dee I a wth Pic 2 4 Mian function Click configuration management display syswindows as pic2 5 Advanced H 264 DVR Pic 2 5 Configuration management Press MENU button on the front panel or the same button on remote control also cuold display the same window 2 4 Configuration management Configuration Management contains nine sub menu basic configuration on site configuration video configuration recording plan alarm configuration network configuration user management PTZ configuration and advanced configuration 10 E w 2 4 1 Basic configuration Click Basic configuration show window as pic2 6 The basic configuration contains two sub menu system date and time 1 system review patrol interv Show Guide Pic 2 6 System In this interface user can setup the device name device ID video format Video Output and language Screensaver and so on The definitions for every parameters display as below Device name It may display on the client end or CMS that help user to recognize the device remotely Device number Corresponding with the remote control number Video format two modes PAL and NTSC User can select the video format according to that of camera Password check Enable this option user needs to input user name and password can do corresponding operations with the relevant right in system configuration Show system time choose d
4. 2 1 4 Disconnect the power by keyboard and mouse Step1 enter into Menu then select System Shut Down icon the Shut down window will appear Step2 click OK the unit will power off after a while Step3 disconnect the power 2 2 Login Equipment start L RPOWER indicator light bright initial password is blank After equipment start press MENU key on panel or press right key on mouse trun to login interface as below User Login iser Name admin n Password Login Pic2 1 User login After Input matching user name and password you can enter system to setup and operation Live preview interface SS SE Sign recordin Manual He Ud A description g record H n state state gt Live playback Click Playbutton to playback the record D ter fast record playback as lelow picture User can do concrete operation by click the buttons on screen 2 3 Main menu setup guide Menu bar Click right mouse or press ESC button on the front panel the control bar will display on the bottom of the screen refer to pic2 2 switch Colour pqz playback N Mm HaQ4 gt a eu P Screen mode E zoom volume record Main menu Pic2 2 Menu bar Click the EI icon near Screen mode appear channel choose frame as below N SE as SE Pic2 3 Channel choose user could choose 1 channel from 1 4 to show live video click to save Click function menu LG will show dialogue frame as Pic 2 4
5. click exit button to exit current interface Video parameters instruction Parameter Meaning Every channel record switch Start use the channel record audio 2 4 3 2 Record bit rate Stream Alarm RecTime mp Resolution Fps Encode v 25 Fps hd 25 Fps v 25 Fps Ki 25 Fps Default Pic 2 12 Record bit rate Setup rate resolution quality encode and max bit stream User can setup all channels with same parameters tick off All then to do relevant setup Click Default button to resort default setting click Apply button to save the setting click Exit button to exit current interface 14 a 2 4 3 3 Record stream introduce menses Range from 1 30 NTSC 1 25 PAL The higher the value is the clearer the Quality Recorded image is Six options lowest lower low medium higher and highest Support CBRand VBR Select range 16Kb 32Kb 64 Kb Max stream 128 Kb 256 Kb 512Kb 640Kb 768Kb 1024Kb 1536Kb 2048Kb Stamp User can overlap the channel name and time stamp on video Pic 2 13 Character overlay Tick off camera name time stamp click Setting button and then user can use cursor to drag the camera name and time stamp in random positions Please refer to below Figures User can also setup all channels with same parameters Click Default button to resort default setting click Apply button to save the setting click Exit button to exit current interfac
6. preset interface click OK button to save the setting click Exit button to exit current interface In the Advance interface click cruise Setting button a dialog box will pop up as below Pic 2 32 Advance cruise Setting Click Add button to add cruise line max 32 cruise line can be added select a cruise line and click Setup button to see a window as below 23 E w e Pic 2 33 Cruise set preset pointsetting Click Add El icon to set the speed and time of preset point select a preset point and click Delete i icon to delete that preset poin click Modify icon el to modify the setting of a preset point User can click those icons to adjust the position of preset point topil up down SS and bottom E Click Preview button to preview the cruise line and then click OK button to save the setting Next click Exit button to exit current interface Select a preset point in the cruise line list box and click Delete button to delete that cruise line click Clear all button to clear all cruise line from the list box click OK button to save the setting click Exit button to exit current interface In the Advance interface click track Setting button to pop up a dialog box as below Pic 2 34 Track setting User can control the dome rotates up up left down right down left left down right and up right and stop rotating adjust the rotate speed and the value of zoom focus and iris of the dome click Star
7. CORD Press to start manual recording AUDIO MUTE 11 STOP Press to stop manual recording TIP When using the remote 12 EXTRA For the future use control to enter password 13 Playback controls and camera titles select the e H Increase reverse playback speed 2X 4X 8X field using the navigation e F Press to start playback buttons press ENTER and s kk Press to increase forward playback speed 2X then press the number 4X 8X buttons e H Press to slow playback speed by 1 2 1 4 1 8 e MIF Press to freeze playback to one frame then press again to advance frame by frame Check whether there is fluorescent light being used in the nearby For the convenience of readers read and quick queries the following sections with a example of 4 channel digital hard disk recorders to introduce the details and pictures are base on this model other model s operation interface are the same except channel and frame rate Corresponding parameter to the same settings individual parameters can be directly and so on 2 Basic function operation 2 1 On off Switching navigation 2 1 1 Start Before start Please ensure all parts connected well Power on Equipment start POWER indicator light is red 2 1 2 Power off User can power off the device by using remote controller keyboard and mouse 2 1 3 By remote controller Press Power button the Shut down window will appear click OK the unit will power off after a while
8. H 264 NETWORK Embedded DVR User Manual V1 1 4 8CH New Interface Thank you for purchase our product Please read this user manual carefully to ensure that you can use the device correctly and safely Attentions The DVR should be installed in a well ventilated place keep suitable space from ground benefit for machine cooling Be sure not to block its air vent keep away from heat sources and high temperaturea environment Please keep the level installation of this product should be avoid install at violently shaking place such as the back of car motor above high and rough luggage rake For avoid short circuit cause fire or other damage when wash the car please prevent DVR include camera and other parts touch water and wet the machine don t have waterproof The equipment consists of Precision Parts please do not try to disassemble or adjust any parts if need maintenance please contact the distributer or customer service Please select the hard disk which commended by the manufacturers suit the DVR work requirement to meet a long time largeamount of data read and write requests please purchase from the formal channels to ensure the hard disk quality This product can t bear heavy weight please do not place heavy object or multi layer laminated on the product Disclaimer The Company is do the best to make the contect correct and complete during the preparation of this manual if has any errors or omiss
9. actual panel AUDIO IN VIDEO IN Connectors on Rear Panel mn Jensen Jesse O lee ees emm Jesemeee eet Lrsesssceregg net Irene VGA output VGA output RS485 RS 485 for connecting PTZ e Video output One video output for connecting TV or monitor BNC SS E 1 5 Remote control In device operation the enter key on remote control has the same function as left click of the mouse The remote control is the secondary input device For navigating the system s interface To use the remote control 1 STANDBY When DVR on constantly press the STANDBY LOGIN LOCK RED button on the top for 3 seconds the DVR will be in standby status Under standby mode press one time for immediate start 2 LOGIN LOCK If Security has been enabled in the Setup menu press to open the user password login screen 3 Number Channel buttons While in menus press buttons 0 9 to enter values during live viewing press to view channels in full screen 4 Press to switch between quad and split screen displays 5 MENU Opens the main menu 6 PTZ Press to open the PTZ control window LR 7 EXIT Close menu windows _ es 3 8 Navigation OK e A Move cursor in menus up gt Move cursor in menus right a Move cursor in menus left e W Move cursor in menus down e OK In menus press to confirm selections during playback and preview press to view system information 9 In menus press to adjust values 10 RE
10. e 2 4 3 4 Recycle record Tick off recycle record to enable the recycle record function It will cover the earlier recorded files and keep recoding when HDD is full if disenabled it will stop recording when HDD is full Note general the image quality frame rate and resolution parameters setting higher the more take up disk space Click Default button to resort default setting click Apply button to save the setting click Exit button to exit current interface 2 4 4 Schedule configuration Schedule configuration includes two sub menus schedule and motion 2 4 4 1 Schedule 15 Se EE E e The volume means the seven days of a week from Monday to Sunday the row means 24 hours of a day Click the grid to do relevant setup Blue means checked area gray means unchecked area Pic 2 14 Schedule Copy User can apply the schedule setting of certain channel to other or all channels Just only select channel and click Copy button Click Default button to resort default setting click Apply button to save the setting click Exit button to exit current interface 2 4 4 2 Motion B O T L O g 0 Pic 2 15 Motion The setup steps of motion are familiar with schedule Note the default schedule of motion detection is full selected that is the color of schedule setting interface is blue 2 4 5 Alarm configuration Alarm configuration includes five sub menus sensor motion video l
11. elevant information click default button to resort default setting click apply button to save the setting click exit button to exit current interface Note the user select a domain name is bound by the Domain Name Service for DVR you must first landing the website of the ISP registered user name and password and then apply fora domain name for the server online After the application is successful the user could enter the domain name to access the server in IE side 2 4 7 User management 20 E Se Enter User management as below pic Pic 2 25 User management Clicking Add button a dialog box will pop up as below Add User Pic 2 26 General D General Input user name password select user type input the MAC address of the PC click OK button this user will be added into the user list box click Exit button to exit the current interface 2 Authority Pic 2 27 Authority In the authority interface assign the definite operation right for that user In the user management interface click Setup button to modify user name user type and binding PC MAC address Select the user that user wants to delete in the user list box and then click Delete button to delete this user click Change password button to modify the password and then click Exit button to exit the current interface 21 e EE Se 2 4 8 P T Z configuration P T Z configuration includes two submenus serial port and advance
12. ement the front panel interface button layout and type real product shall prevail The front panel buttons Description Buttons on Front Panel 1 IR Sensor Red Color IR receiver for the remote control 2 LED Indicators Shows status of alarm rec power link HDD 3 Playback During playback press the following e 44 Increase reverse playback speed 1X 2X 4X CU Press to freeze playback to one frame then press again to advance frame by frame b Press to start playback WW Press to slow playback speed by 1 2 1 4 1 8 bP Press to increase forward playback speed 1X 2X 4X 4 MENU OK Press to open close the main menu or confirm 5 Navigation Press the Navigation buttons to perform the following e In menus press to confirm selections in PTZ mode press to change the navigation buttons to control the connected PTZ camera not included Press to move cursor up in PTZ mode press to pan camera up Y Press to move cursor down in PTZ mode press to pan camera down Press to move cursor left in PTZ mode press to pan camera left gt Press to move cursor right in PTZ mode press to pan camera right 6 USB Connect a USB flash drive to the top port for data backup and firmware upgrades connect a USB mouse to the bottom port 1 4 Rear panel diagram Statement the rear panel interface button layout and type real product shall prevail below rear panel picture may be different with the
13. ent and version information and relevant information Log information Enter menu gt View system information gt Log information in the interface users can set the start amp end time of log you want to view select the type of log you want to view and click the search button searched the log information will be displayed in the log list box Note Users can export data files to be backed up on removable storage devices Network information Enter menu gt view information gt Network configuration in the interface Users can view the relevant parameters of the network information 2 8 Disk management Enter menu gt Disk management In the interface the user can view disk storage state also can choose to formatting the hard disk Please format the hard disk before record Specific operation as below Step1 enter into disk management interface The system will pop up the Disk Management window Step2 select a hard disk and click Format button to star format set the property of the disk then click Apply button to save the setting Note all recorded files in the hard disk will be lost after formatted 2 9 Upgrade Once have the new version the user can choose to upgrade the panel and the mianboard can get upgraded software from the buyers to upgrade the system Upgrade step user needs to copy the upgrade software which get from vendor into the USB storage device and then connect to the USB port Enter Menu Upgrade refr
14. esh list the upgrade software name is displayed in the upgrade list box select that software and click Upgrade button to start upgrading System will automatically restart on the upgrade process Please wait for a while when the system is rebooted Please don t cut off power during upgrading This system supports the upgrade of the USB device but it must be compatible with the USB device need to reboot the system after the upgrade completed to take effect Note If the upgraded software does not appeared in USB usually the USB devices are not compatible 28 2 10 Logoff Enter Menu gt Logoff Click Log off icon The system will exit the current user login If re wants to log in again click mian menu icon to enter into user name and password to re login 2 11 System shut down Click system shut down icon shut down system 29
15. ions without any liability the company reserves the right to change any hardware and software mentioned inthis manual at any time and without explain beforehand Thank you for choosing our products please read this manual carefully before use Due to not according to the specified operating losses company will not assume any financial liability and legal responsibility CONTENT dee te Age el te e DEEN 2 Oe UBM IAI EE 2 UE E la TUN Leite EE 4 1 3 Front panel buttons description 2 1 4 Rear een E ege EE 6 1 5 Remote Control T 2 Basic function operaton cee eee ceescccessccesssccsscecessseessscesssscessecesseecsssecesseecetseeeess 2 2 1 On off Switching Navigatoare a a e E 2 E e IN EE 8 2 3 Main menu Setup HEEN eege deet eg een 2 2 4 Configuration management 10 241 BASIC COMMOUPAUOM DEE 2 Z AD LIVE COMIGUPALOMN EE 2 2 4 3 Record CONMIGUIALION nade dela enn ea 2 2 4 4 Schedule Confguraton 2 2 AS Alani CONNQUIAUON cic Seier E ee 16 2 4 6 Network COMMGUIATION vos sescsssscsctisenncgursexcpodeceegecause cesaerasbens sonaveasuseeoudatedeavavees 2 2 4 7 User MaANAGCINGIN EE 20 24 Ore WZ e Te 2 2 4 9 Advance CONFIQUPATION cc cccccesccseccessecesccsssecesceessecessecesscesseeesecsseeeses 2 29 Data retrieval EE 2 EE 2 2022 EVENT SCAICM EE 2 ZO BAC KUD EE 2 21 CMEC MALO AON EE 2 2 8 Disk LAVA OVNI ee 2 Zo leie e Tel 2 2 OME oo 6 GE 2 2 11 System sh t GOWN E 2 1 Product Introduction 1 1 Summary Thi
16. isplay time in liveor not Video output the resolution of live display interface range from VGA800 600 VGA1024 768 VGA1280 1024 and CVBS Language setup the menu language Simplified Chinese Traditional Chinese English Japanese German Russian French Portuguese Turkish spanish Italian Polish Hungarian Slovak Vietnamese greek Click the Default button the system restore the default things Click the Apply button will save the above settings Click the Exit button to exit the current interface Tip to change the menu language and video output the device will restart 2 Time amp date Pic 2 7 Time amp date E SS E o SE E SS E a Set the date format time format time zone at the date and time interface check the Keep synchronized with network time server to update the network time server You can alsomanually adjust the system time Note The system default is GMT time zone please choose GMT 8 in the time zone drop down frame Click the Default button the system restore the default settings Click the Apply button will save the above settings Click the Exit button to exit the current interface 2 4 2 Live configuration Click Live configuration enter window as pic2 8 Live configuration includes two submenus live and mask 2 4 2 1 Live configuration Pic 2 8 Live configuration Note Click Camera Name to see a soft keyboard User can choose different character format to inp
17. k TEST button to test the effectiveness of the relevant information Click Default button to resort default setting click Apply button to save the setting Click Exit button to exit current interface 2 4 6 2 Network Sub stream Network Network Sub stream ition Fps Default Apply Exit Pic 2 22 Network Sub strea select fps resolution quality user can also setup all channels with same parameters click Apply button to save the setting click Exit button to exit current interface network configuration network Parameter Meanimg gt gt O Range from 1 25 PPS Support CIF The higher the value is the clearer the record image Six options lowest lower low medium higher and highest 19 Se 2 4 6 3 Email Default Apply Pic 2 23 Email SMTP Server Port the name and port number of SMTP server Send address password sender s email address password Receive address receiver s email address Here user can add at least three mail addresses Click Test button to test the validity of the mailbox Click Default button to resort default setting click Apply button to save the setting click Exit button to exit current interface 2 4 6 4 Other settings Default Apply Pic 2 24 Other settings Enable DDNS server user needs to input user name password and host domain name of the registered website click TEST to test the effectiveness of the r
18. nding button on the screen to start concrete operations play pause Next section Colour control Volume exit StOP FF amp rewind E zoom Hide Last section Play process Pic 2 37 Playback buttons 2 5 2 Event search Step1 enter into Search configuration event search refer to below pic 26 vm vxOU Pic 2 38 Event search Step2 After clicking Search button the searched event information will displayed in the event list box double check a certain record file to playback Step3 User can select date channel Tick off Motion Sensor or All accordingly to search 2 6 Backup This unit supports backup by USB device User also can make backup by IE browser via internet Step1 enter into backup configuration interface as below pic Pic 2 39 Data backup Step2 set the start amp end time select channels and click Search button to display the searched data in the data backup list box Step3 checked a data file or tick off All to select all data files click Backup button Step4 in the backup information interface user can check the relevant information of backup files storage type save file type etc click Start button to starting backup 27 2 7 Check information Through this option the user can check system information system journal network information System Information Enter menu gt view information gt system information in the interface user can view the equipm
19. ompressed in real time by independent hardware The sound and image keep stabilized synchronization gt Backup Function It backups through USB port such as common U disk mobile hard disk etc The client computer can download and backup the files on the hard disk via the internet gt Video Playback Function Each channel can realize independent and real time recording while retrieval reverse play network monitoring video search and download etc can realize simultaneously Multiple playback modes slow forward fast forward reverse play and frame by frame play When playing back the video the exact time of the event can be displayed gt Network Operation Function Through the internet you can realize remote and real time monitoring remote video search and playback and remote PTZ control gt Communication Port With RS485 port and PTZ control With standard Ethernet port realizing network remote control function gt PTZ Control Support the PTZ decorder which communicates through RS485 Can expand multiple decoding protocols facilitating the realization of PTZ and dome camera control gt Intelligent Operation Mouse operation function For the same settings on the menu you can copy and paste quickly check equipment and accessories When you receive the product please check the accessories are complete or not DVR accessories generally include mouse power lines and data lines 1 3 Front panel buttons description Stat
20. oss and alarm out 2 4 5 1 Sensor The hardware does not support 2 4 5 2 Motion Motion includes one sub menus motion 1 gt Motion 16 SS SE SE SE Sst E SE e Detlay s Alarm Handling Area Pic 2 16 Motion Click start motion alarm and set alarm hold time It refers to after close motion alarm it delay to the preset setting time Click alarm Settings button show below window Alarm Handling Pic 2 17 Alarm handling Alarm configuration trigger video alarm handling linkage alarm handling and sensor alarm handling trigger settings is same Click on Regional Settings button at Motion detection interface trun to the following window Pic 2 18 Motion detection Regional Settings At area Setting interface users can drag the slider to adjust the sensitivity value 1 5 the default value is 4 1 5 sensitivity progressive increase Sensitivity influenced by the color of time day or night the users should adjust according to actual situation clickiisiicon set All locales for the detection region click el icon will clear setting detection region click La icon save setting click Ea utton exit from current interface User can setup all channels with same parameters please tick off all and then to do 17 SE EE SS relevant setup Click Default button to resort default setting Click Apply button to save the setting Click Exit button to exit current interface
21. s device is a digital monitoring and recording product specially designed for the security field It adopts standalone processor and standalone Linux operating system The device combines with the latest technologies in the IT field such as video and audio compression decompression large capacity HDD record TCP IP network etc The code is embedded in the FLASH chip which makes the system running more steadily This device has both features of digital video and audio recording DVR and digital video and audio server DVS It can not only work locally and independently but also compose of a powerful security monitoring net with networking With the use of professional network video surveillance platform network software it can fully reflect its strong networking and remote monitoring capability It can be used for the security protection in the fields of banking telecommunications electronic power justice traffic residential factory warehouse water conservancy facilities and other areas and departments 1 2 Main Functions gt Real time Monitoring It is with analogue video output port VGA port It can realize the monitoring function through the monitor or display It supports simultaneous TV and VGA output gt Storage Function It adopts special format to save data which cannot be tampered with and will be secured gt Compression Method It supports multi channel audio and video signal Each channel of audio and video signal is c
22. t Record button to record the move track of PTZ and click this button again can stop record click Start track button to play recorded track and click this button again can stop play The user can drag the slider to adjust the rate of P T Z movement Click icon to hide the tool bar right key can remerge it click icon to exit the current interface In the Advance interface click Default button to resort default setting click Apply button to save the setting click Exit button to exit current interface 24 d S a oe 2 4 9 Advance configuration Advanced settings include three sub menu factory settings andimport export and exit 1 Factory settings all settings back to factory settings 2 Import Export Users can export data files to be backed up onremovable storage devices you can also import the specified data file from a removable storage device to a DVR 3 Exit exit current interface Pic 2 35 Advance configuration 25 SE EE SS SE Returned to the main menu enter the data retrieval interface 2 5 Data retrieval Search configuration includes two submenus Time Search Event Search 2 5 1 Time search Step1 enter into Search configuration gt Time Search refer to below pic Pic 2 36 Time search Step 2 Select the channel the calendar date the start time and end time Step 3 click Play RA mon Playback will start from the set time bucket click the correspo
23. ut Tick off camera name and click Setting button to display a window as below trightness Hue taturation ontrast Default Save Pic 2 9 Live color adjustment In this interface user can adjust brightness hue saturation and contrast in live click Default button to resort default setting click OK button to save the setting user can setup all channels with same parameters please tick off all and then do relevant setup 2 4 2 2 Mask Private mask User can setup private mask area on the live image picture 12 Pic 2 10 Mask Setup mask area click Setting button enter into live image to press left mouse and drag mouse to set mask area refer to below picture Click Apply button to save the setting Delete mask area select a certain mask area click left mouse to delete that mask area click Apply button to save the setting Live image mask area 2 4 3 Record configuration Click Record configuration enter window as pic2 11 Record configuration includes four sub menus start record bit rate Character overlay recycle record 13 Se 2 4 3 1 Start Record Enable Stream CH Enable v Default Apply Pic 2 11 Start Tick off record channel channel audio User can setup all channels with same parameters tick off All then to do relevant setup Click Default button to resort default setting click Apply button to save the setting
Download Pdf Manuals
Related Search