TRP-100 User`s Manual 3 - Support Technique AURES
Contents
1. TRP 100 Receipt Printer User s Manual All specifications are subject to change without notice Disposal of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product x PRINTER COVER Open this cover to load or replace paper TABLE OF CONTENTS 1 Parts Identifications 3 2 Setting up the printer 4 2 1 Unpacking 4 2 2 Connecting the cables 5 2 3 Loading the roll paper 9 2 4 Dip switch setting 11 3 Control panel and other functions 17 3 1 Control panel 17 3 2 Error Indicating 17 4 Self Test 18 9 Hexadecimal Dump 19 6 Specifications 20 6 1 General Specifications 20 6 2 Auto Cutter Specifications 22 6 3 Interface 22 6 4 Electrical Characteristics 22 6 5 Environmental Reguirements 23 6 6 Reliability 23 6 7 Certification 23 6 8 Black Mark specifications 24 7 Command List 25 TRP 100 User s Manual 1 Parts Identifications CONTROL PANEL2. s Manual 6 8 Black Mark specifications Cut position Upper margin 17 5mm or more lt Note gt Printing direction a Reverse Front side of the paper 10mm or more T 1 The cut position shown above is adjustable 2 The black mark s PCB value must be 0 90 or more 24 Adjustable 3mm or more Bottom margin 7 Command List TRP 100 User s Manual No Command Function REMARKS 1 HT Horizontal tab 2 LF Print and line feed 3 CR Print and carriage return 4 FF Print and return to standard mode in page mode 9 CAN Cancel print data in page mode 6 DLE EOT Real time status transmission T DLEENG Real time reguest to printer 8 DLE DC4 Generate pulse at real time 9 ESC FF Print data in page mode 10 ESC SP Set right side character spacing 11_ ESC Select print mode s 12 ESC Set absolute print position 13 ESC Select cancel user defined character set 14 ESC amp Define user defined characters 15 ESC Set bit image mode 16 ESC Turn underline mode on off 11 ESC2 Select default line spacing 18 ESC3 Set line spacing 19 ESC Select peripheral device 20 ESC Cancel user defined characters 21 ESC Initialize printer 22 ESCD Set horizontal tab positions 23 ESC E Turn emphasized mode on off 24 ESC G Turn double str
3. Features LED indicators to indicate printer status and switches to operate the printer COVER OPEN LEVER Pull down this lever to open the printer cover POWER SWITCH Used to turn on off power to the printer gt INTERFACE CONNECTOR PERIPHERAL DRIVE CONNECTOR POWER CONNECTOR TRP 100 User s Manual 2 Setting Up the Printer 2 1 Unpacking Your printer box should include these items If any items are damaged or missing please contact your dealer for assistance The Printer User s Manual Roll Paper Adaptor Option Interface Cable optional TRP 100 User s Manual 2 2 Connecting the Cables You can connect up the cables required for printing to the printer They all connect to the connector panel on the back of the printer which is shown below INTERFACE CONNECTOR PERIPHERAL DRIVE CONNECTOR POWER CONNECTOR For connection to a Connects to peripheral units For connection of host computer such as cash drawers etc the AC adapter Do not connect this to Never unplug the AC adapter a telephone while the printer is on Before connecting any of the cables make sure that both the printer and the computer are turned off TRP 100 User s Manual 2 2 1 Interface Connector 14 ed 000 000000000 0900000 00 00 0000 1 13 lt D SUB 25 Female
4. Serial gt lt Centronics Parallel gt Link END Status END 0000 00000 TRP 100 User s Manual Centronics Parallel Interface PIN SIGNAL I O DESCRIPTION 1 STROBE Input Synchronize signal Data received 2 9 DATAO 7 Input Output_ Data bit Transmitted 0 7 10 ACK Output Data receiving completed 11 BUSY Output Impossible to print of data receiving 12 PE Output Paper empty 13 SELECT Output Printer status for ON OFF line 14 AUTO FEED Input Paper auto feed signal 15 GROUND System ground 16 GROUND System ground 17 NC 18 LOGIC H 5V 19 30 GROUND System ground 31 INIT Input Initialize 32 ERROR Output Printer error 33 GROUND System ground 34 NC 35 5V 5V 36 SELLECT IN Input Printer select signal Ethernet Interface PIN SIGNAL I O 1 Data Out Output Data 2 Data Out Output Data 3 GND Ground 4 Data IN Input Data 5 Data IN Input Data 6 N C 7 N C 8 N C RS 232 lt USB COMBO gt lt Wi fi gt Serial Interface PIN SIGNAL 1 0 DESCRIPTION 2 TXD Output Printer transmit data line RS 232C level 3 RXD Input Printer receive data line RS 232C level 4 20 DTR Output Printer handshake to host line RS 232C level 6 DSR Input Data Send Ready le GND System Ground USB Interface PIN SIGNAL 1 0 DESCRIPTION 1 5V 5V 2 DATA Printer transmit
5. data line 3 DATA Printer transmit data line 4 GND System Ground TRP 100 User s Manual 2 2 2 Cash Drawer Connector The printer can operate two cash drawers with a 6 pin RJ 11 modular connector The driver is capable of supplying a maximum current of 1 0A 24VDC for 510ms or less when not printing PIN SIGNAL DESCRIPTION 1 Signal GND 2 Drawer kick out drive signal 1 Output 3 Drawer open close signal Input 4 24V 5 Drawer kick out drive signal 2 Output 6 Signal GND Caution To avoid an overcurrent the resistance of the drawer kick out solenoid must be 24 Q or more TRP 100 User s Manual 2 3 Loading the Roll Paper Notes Be sure to use paper rolls that meet the specifications Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly Turn off power switch 1 Make sure that the printer is not receiving data Otherwise data may be lost 2 Open the paper roll cover by pushing down the cover open button 3 Remove the used paper roll core if there is one inside 4 Insert new paper roll as shown TRP 100 User s Manual 5 Be sure to note the correct direction that the paper comes off the roll S Z 6 Pull out a small amount of paper as shown Then close the cover 7 Tear off the paper as shown 10 2 4 Dip Switch Setting TRP 1
6. 00 User s Manual The printer is set up at the factory to be appropriate for almost all users On the other hand offers some more settings for users with special requirements It has DIP switches that allow you to change communication setting such as handshaking and parity check as well as print density Your printer has two sets of DIP switches The functions of the switches are shown in the following tables Note Power off And open the cover of Dip Switch and change setting 2 4 1 Serial Interface Specification DIP Switch Set 1 Functions SW FUNCTION ON OFF DEFAULT 1 Data Receive Ignored Print OFF 2 Hexadecimal HEXDUMP NORMAL OFF 3 Hand Shaking XON XOFF DTRDSR OFF 4 Data Length 7bits 8bits OFF 5 Parity Check ENABLED DISABLED OFF 6 Parity Check EVEN ODD OFF Baudrate selection Transmission speed 4800 bps 9600 bps 19200 bps 38400 bps OFF OFF Print Density Print Density SW 9 SW 10 Low Power ON ON Normal OFF ON Normal ON OFF Dark OFF OFF 11 TRP 100 User s Manual 2 4 2 Parallel Interface Specification DIP Switch Set 1 Function SW FUNCTION ON OFF DEFAULT 2 Hexadecimal HEXDUMP NORMAL OFF 5 Bi Parallel mode DISABLED ENABLED OFF Print Density Print Density SW 9 SW 10 L
7. Enable disable Automatic Status Back ASB 57 GSf Select font for HRI characters 58 GSh Set bar code height 59 GSk Print bar code 60 GSr Transmit status 61 GSv0 Print raster bit image 62 GSw Set bar code width lt Add gt 1 ESCi Full cut 2 EsCm Partial cut 3 FS Set print mode s for Kanji characters 4 FS amp Select Kanji character mode 9 FS Turn underline mode on off for Kanji character 6 FS Cancel Kanji character mode 7 _ FS2c1d1 dk_ Define user defined Kanji characters 8 FSC Select Kanji character code system 9 FSS12 Set Kanji character spacing 10 FSW Turn quadruple size mode on off for Kanji character 26 Rev 2 0
8. ace Ethernet Interface 10Mbps Wi fi 802 11b 6 4 Electrical Characteristics 1 Input Voltage DC 24V 10 2 Current Consumption Operating Approx 1 5 A at ASC II printing Peak Approx 10 A at print duty 100 For 10 seconds or less Stand by Approx 0 15A 3 Power Connector PIN2 No CONNECTION 22 TRP 100 User s Manual Important When connecting or disconnecting the power supply from the printer be sure that the following cautions are observed 1 Use a power supply Limited Power Supply of DC 24V 10 and more than 2 5A 2 Be careful about installing the printer in an area where there is noise 3 Take the appropriate measure to protect against electrostatic AC line noise etc 6 5 Environmental Requirements 1 Operating Temperature 5 C to 40 C Humidity 10 to 90 RH without condensation 2 Transport Storage except paper Temperature 20 C to 60 C Humidity 10 to 90 RH without condensation 6 6 Reliability 1 MCBF 60 million lines based on an average printing rate of 12 5 with paper thickness in the range of from 65m 751m 39 million lines based on an average printing rate of 12 5 with paper thickness in the range of from 76m 1501m 2 Head Life 100 million pulses 100Km 3 Cutter Life 1 0 million cuttings if the paper thickness is between 65 and 100mm 6 7 Certification 1 FCC PART15 CLASS A 2 CE EMCD LVD 3 UL CUL 4 4 MIC 23 TRP 100 User
9. e hexadecimal codes and the second column gives the ASC characters that correspond to the codes Hexadecimal Dum 1B 21 00 1B 26 02 40 40 amp 1B 25 01 1B 63 34 00 1B c4 41 42 43 44 45 46 47 48 ABCDEFGH A period is printed for each code that has no ASC equivalent 3 Turn off the printer and make sure that Dip sw 1 2 off 4 Turn on the printer 19 TRP 100 User s Manual TRP 100 User s Manual 6 Specifications 8 Overall dimension Appendix A Specifications 6 1 General Specifications 1 Printing Method Direct line thermal printing 2 Print speed 150mm sec Approx 35 4LPS ms 4 3 Dot density Le i 180 DPI Hor Ver 180 180 0 141mm 0 141mm dot 203 DPI Hor Ver 203 180 0 125mm 0 141mm dot 4 Printing Width Max 72mm 512 dots 4 Max 72mm 576 dots 5 Number of print columns No of columns 6 Roll paper Refer to chapter 2 for details on the recommended roll Paper Paper width 80mm 0 1mm Roll diameter Max 83 0mm 7 Weight 1 6Kg 20 21 TRP 100 User s Manual 6 2 Auto Cutter Specifications 1 Cutting Frequency Max 30 cuts per minute 2 Thickness of paper 0 065 0 1 mm 3 Cutter Life 1 0 million cuttings if the paper thickness is between 65 and100yum 6 3 Interface RS232C Serial Interface Centronics Parallel Interface IEEE1284 USB Interface USB COMBO Interf
10. ike mode on off 25 ESC J Print and feed paper using minimum units 26 ESC L Select page mode 21 ESCM Select character font 28 ESC R Select an international character set 29 ESC S Select standard mode 30 ESCT Select print direction in page mode 31 ESC V Turn 90 clockwise rotation mode on off 32_ ESC W Set printing area in page mode 33 ESC Set relative print position 34 ESC a Select justification 35 ESC c3 Select paper sensor s to output paper end signals 36 ESC c4 Select paper sensor s to stop printing 37 ESC c5 Enable disable panel buttons 38 ESC d Print and feed paper n lines 39 ESC p General pulse 40 ESCt Select character code table 25 TRP 100 User s Manual No Command Function REMARKS 41 ESC Turn upside down printing mode on off 42 FSp Print NV bit image 43 FSg Define NV bit image 44 GS Select character size 45 GS Set absolute vertical print position in page mode 46 GS Define downloaded bit image 47 GS Print downloaded bit image 48 GSB Turn white black reverse printing mode on off 49 GSH Select printing position of HRI characters 90 GSI Transmit printer ID 91 GSL Set left margin 92 GSP Set horizontal and vertical motion units 93 GSV Select cut mode and cut paper 54 GSW Set printing area width 55 GS Set relative vertical print position in page mode 96 GSa
11. is jammed with cutter the top cover might be stuck In this case repeat power on and off several times If the top cover is still stuck please follow the steps to release the papers from jamming 1 Make sure the printer is turned off 2 Take out cutter cover as shown 16 TRP 100 User s Manual 3 Control panel and other functions 3 1 Control panel You can control the basic paper feeding operations of the printer with the button on the control panel The indicator lights help you to monitor the printers status Control Panel QO POWER OERROR QO PAPER FEED Button The button can be disabled by the ESC c 5 command Press the FEED button once to advance paper one line You can also hold down the FEED button to feed paper continuously 3 2 Error indicators This section explains the different patterns signaled by the three LED indicators located on the top cover of the printer STATUS REMARKS Power dif OFF OFF OFF a power is not supplied to the Power on OFF OFF ON Normal power is supplied to the printer On line OFF OFF ON Normal error free mode Cover open OFF ON ON Close cover Paper empty OFF ON ON Insert new paper roll Test mode OFF OFF ON Ignored error led 17 TRP 100 User s Manual 4 Self Test The self test lets you know if your printer is operating properly It checks the control circuits printer mechanisms print quality ROM version and DIP swi
12. ow Power ON ON Normal OFF ON Normal ON OFF Dark OFF OFF 2 4 3 USB COMBO lnterface Specification DIP Switch Set 1 Function SW FUNCTION ON OFF DEFAULT 2 Hexadecimal HEXDUMP NORMAL OFF COMBO Serial Option SW FUNCTION ON OFF 3 HANDSHAKING XON XOFF DTR DSR 4 DATA LENGHT TBITS 8BITS 5 PARITYCHECK ENABLED DISABLED 6 PARITYCHECK EVEN ODD Baudrate selection Transmission speed SW 7 SW 8 4800 bps ON ON 9600 bps OFF ON 19200 bps ON OFF 38400 bps OFF OFF Print Density Print Density SW 9 SW 10 Low Power ON ON Normal OFF ON Normal ON OFF Dark OFF OFF 12 2 4 4 USB Interface Specification DIP Switch Set 1 Function TRP 100 User s Manual SW FUNCTION ON OFF DEFAULT 2 Hexadecimal HEXDUMP NORMAL OFF Print Density Print Density SW 9 SW 10 Low Power ON ON Normal OFF ON Normal ON OFF Dark OFF OFF wenn ence SEE RES SEE ER EEEERE old USB DIP Switch Set 1 Functions SW FUNCTION ON OFF DEFAULT 1 Data Receive Ignored Print OFF 2 Hexadecimal HEXDUMP NORMAL OFF 3 Hand Shaking XON XOFF DTR DSR OFF 4 Data Length 7bits 8bits OFF 5 Parity Check ENABLED DISABLED OFF 6 Parity Check EVEN ODD OFF Baudrate selection Transmission speed SW 7 SW 8 4800 bps ON ON 9600 bps OFF ON 19200 bps ON OFF 38400 bps OFF OFF Print Density Print Densit
13. tch settings This test is independent of any other equipment or software Running the self test 1 Make sure the printer is turned off and the printer cover is closed properly 2 While holding down the FEED button turn on the printer using the switch on the front of the printer to begin the self test The Self Test prints the printer settings and then prints the following Cuts the paper and pauses Error LED On Self test printing Please press the PAPER FEED button 3 Press the FEED button to continue printing The printer prints a pattern using the built in character set 4 The self test automatically ends and cuts the paper after printing the following Completed The printer is ready to receive data as soon as it completes the self test 18 TRP 100 User s Manual 5 Hexadecimal Dump This feature allows experienced users to see exactly what data is coming to the printer This can be useful in finding software problems When you turn on the hex dump function the printer prints all commands and other data in hexadecimal format along with a guide section to help you find specific commands To use the hex dump feature follow these steps 1 After you make sure that the printer is off and Dip s w 1 2 is ON turn on the printer 2 Run any software program that sends data to the printer The printer prints Hexadecimal Dump and then all the codes it receives in a two column format The first column contains th
14. y SW 9 SW 10 Low Power ON ON Normal OFF ON Normal ON OFF Dark OFF OFF 13 TRP 100 User s Manual 2 4 5 Wi fi Specification DIP Switch Set 1 Function SW FUNCTION ON OFF DEFAULT 2 Hexadecimal HEXDUMP NORMAL OFF Print Densit Print Density SW 9 SW 10 Low Power ON ON Normal OFF ON Normal ON OFF Dark OFF OFF 2 4 6 Ethernet Interface Specification DIP Switch Set 1 Function SW FUNCTION ON OFF DEFAULT 2 Hexadecimal HEXDUMP NORMAL OFF Print Densit Print Densit SW 9 SW 10 Low Power ON ON Normal OFF ON Normal ON OFF Dark OFF OFF DIP Switch Set 2 Function Emulation FUNCTION SW 1 SW 2 Epson TM 88 OFF OFF IDP 3540 OFF ON Cutter SW FUNCTION ON OFF Remarks 3 Cutter FULL CUT PARTIAL CUT Only Epson mode 14 CAUTION TRP 100 User s Manual Turn off the printer while removing the DIP switch cover to prevent an electric short which can damage the printer 1 Make sure the printer is turned off 2 Remove the screw from the DIP switch cover Then take off the DIP switch cover as shown in the illustration below 3 Set the switches using a pointed tool such as tweezers or a small screwdriver 4 Replace the DIP switch cover Then secure it with the screw The new settings take effect when you turn on the printer 15 TRP 100 User s Manual amp CAUTION When the paper
Download Pdf Manuals
Related Search