2044CL-O (2044CL-O-T) User Manual
Contents
1. 2044CL O User Manual doc 2044CL O 6 300 Clip Instant Access System 1 REVISION HISTORY 081204 1 0 Original document 120104 Rev 1 1 Updated 57420 Troubleshooting section 063005 Rev 1 2 Added Video Reference instructions 051706 Rev 1 21 Added hash mark to looping function 2044CL O 6 300 Clip Instant Access System Getting Started 2 SYSTEM DESCRIPTION The 2044CL system includes DNF s most robust controller the ST400 with the industry s premiere Shotbox the ST420 The ST400 controls up to 6 video channels individually or ganged It features full transport functionality The LCD buttons on the Shotbox display clip names and delivery instant access to video clips on up to 8 channels The assign able keys on the ST420 Shotbox allow clip names to be organized on ten different banks of keys for easy access The 2044CL provides instant access to fill clip and key clip combinations with the press of one key The 2044CL O supports Odetics Broadcast protocol and requires that the Video Server be controllable under Odetics Broadcast Protocol The 2044CL provides instant access to existing video clips stored in the Grass Valley Group PROFILE the Leitch VR and other Video Servers supporting Odetics Broadcast Protocol Definitions Throughout this document DDR amp Video Server will be referred to collectively as Video Server Q The ST400 S SM will be referred to as ST400 Q The2. LED indicator will turn on Select the desired BANK by pressing the appropriate bank key Press and hold the desired Shotkey The LCD display on the Shotkeys will show the current assignment of all 8 VTRs for the pressed Shotkey Release the Shotkey and VIEW when done viewing Repeat steps a through e 20 CREATE CUE POINT LABELS Use LABELS mode to assign meaningful names to cue points Rather than viewing cryptic CLIP 105 on the Shotkeys LABELS provides a faster and easier method to select cue points If different parts of the same clip are assigned to many Shotkeys LABELS allows a unique name to be assigned to each Shotkey ON THE 1400 a b NOTE Select cue point to label Press the LABEL key Manually enter a label up to 8 characters in length using the numeric keypad ST420 Shotbox QWERTY keyboard or PC keyboard Press the LOAD shotkey on the Shotbox to assign the entered label to the selected cue point OR ENTER on the ST400 OR ENTER on the PC keyboard OR ESC to exit without save Labels are saved in non volatile memory in the ST400 not in the Shotbox They are not saved in the video server 2044CL O 6 300 Clip Instant Access System 17 Reference 21 SETUP MENU Press MENU The MENU indicator will turn on The display will show the following parameters with their current settings Turn the wheel to select a menu option Press the CHANGE softkey to modify the curren
3. Optional Press OUT to mark an OUT point The OUT LED will turn on On recall the clip will play to the OUT point then stop To delete an IN or OUT point press and hold DEL then press IN or OUT The IN OUT LED will turn off If no IN point is marked the current location of the clip will be learned as the IN point For GANGs repeat steps a b c for each channel Then press the GANG softkey Press VTR 1 2 3 4 5 or 6 key or VTR7 or VTR8 softkey to add it to the GANG The VTR LED will turn on Press the VTR key again to remove it from the gang The VTR LED will turn off Press ESC to exit GANG mode The LEDs of all GANGed VTRs will turn on Select the desired Cue Point by pressing NEXT CUE LAST CUE or by manually entering the Cue Point using the numeric keypad followed by ENTER The selected Cue Point number is shown on the bottom part of the display Press SHIFT MARK to initiate the LEARN The display will show Select VTRs to learn 2044CL O 6 300 Clip Instant Access System 8 Select the VTRs to learn by pressing keys 1 2 3 4 5 or 6 key or VTR7 or VTR8 softkey Press MARK to complete the learn process Note Learn will overwrite the previous contents of the Cue Pooint Press ESC anytime to escape without learning 2 BVW PROTOCOL a 2044CL O 6 300 Clip Instant Access System Select the desired Cue Point by pressi
4. ST420 SHOTBOX will be referred to as Shotbox SHOTKEY refers to the 1 30 switches on the Shotbox Q Words surrounded by brackets for example ENTER are keys on the ST400 or the SHOTBOX XXX XXX means hold the two keys down simultaneously The 6 keys directly below the display are referred to as Softkey Their function changes as indicated on the last line of the display i e GANG Shotkeys and Cue Points refer to the same memory locations Both terms are interchangeable 2044CL O 6 300 Clip Instant Access System 5 3 SYSTEM INSTALLATION SHOTBOX Video Server RS422 Serial Port 1 RS422 Serial Port 8 1 Plug one end of a standard 9 pin RS422 serial cable into the OUTPUT connector on the rear of the Shotbox Plug the other end of the cable into the SHOTBOX connector on the rear of the STAOO Connect the supplied POWER SUPPLY AULT SW300 into the POWER connector on the rear of the SHOTBOX Plug the Power Supply into an outlet 90 VAC 240 VAC ST400 S SM VTR DDR CONTROLLER 1 Plug one end of a 9 conductor RS422 serial cable into the 2 3 4 5 6 or Shotbox or PBIO connector on the rear of the 57400 Plug the other end of the cable into the 9 pin REMOTE connector on the Video Server NOTE 7 is connected to PBIO connector the back of the ST400 4 VTR8 is connected to Shotbox connector on the back of the ST400 Connect the supplied POWER SU
5. and hold the SHIFT key 3 Press the desired Shotkey to be cleared After the cue point is cleared the Shotkey will be blank 11 PLAY CLIP See LOAD A CLIP Section 5 or RECALL A CLIP Section 7 a ON THE ST400 1 Set an IN Point and OUT Point if desired Jog Shuttle to the desired IN point Press IN Jog Shuttle to the desired OUT point Press OUT OR Press SHI FT IN Manually enter the IN time on the numeric keypad Press ENTER Press SHI FT OUT Manually enter the OUT time on the numeric keypad Press ENTER 2 Press RECUE The clip will cue to the IN point 3 Press PLAY The clip will play from its current time to the OUT point then stop 2044CL O 6 300 Clip Instant Access System 12 b ON THE SHOT BOX 1 Press RECUE The clip will cue to the IN point 2 Press PLAY The clip will play from its current time to the OUT point then stop 12 LOOP CLIP ON THE ST400 a Load the clip using LOAD A CLIP Section 5 or RECALL A CLIP Section 7 The clip MUST be loaded from the 2044CL b Optional Set an IN Point and or OUT Point Jog Shuttle to the desired IN point Press IN Jog Shuttle to the desired OUT point Press OUT OR Press SHIFT IN Manually enter the IN time on the numeric keypad Press ENTER Press SHIFT OUT Manually enter the OUT time on the numeric keypad Press ENTER Press LOOP ENABLE The clip will immediately start loo
6. the Learned VTRs cue the clips to the Learned IN time then set the Learned GANG mode b ON THE SHOTBOX 1 Select the desired BANK by pressing BANK 1 2 3 4 5 6 7 8 9 or 0 The Shotkeys will display the assigned CLIP 105 for the selected bank 2 Press the desired Shotkey The selected clip or clip combination will be loaded on the learned channels and cued to the learned IN point The learned OUT point and GANG mode will be set RECUE CLIP a Press RECUE If an IN Point is marked the IN indicator is on the clip will RECUE to the IN Point If the IN point is not marked the clip will RECUE to the start of the clip b Press CUE OUT to cue to the marked OUT point REALI GN GANGED CHANNELS When the channels are Jogged Shuttled Slomoed in gang they may drift apart To bring the channels back to their initial offsets press SHIFT STOP 2044CL O 6 300 Clip Instant Access System 10 CLEAR CUE POINTS a ON THE ST400 1 Select the cue point to be cleared using NEXT CUE LAST CUE or manually entering the cue point number 2 Press SHIFT MARK The CLEAR softkey will be displayed on the bottom of the display 3 Press the CLR CUE softkey to clear the cue point The cue point will be cleared and the display will return to the normal screen OR Press ESC to escape without clearing b ON THE ST420 SHOTBOX 1 Select the desired BANK by pressing the desired bank key 2 Press
7. video source SOURCE such as a VIR The SOURCE is connected to the VTR6 connector on the rear of the 2044CL O Prior to performing a capture press MENU Set the PREROLL value for the SOURCE VTR Typical value is 5 seconds Set the RECORD DELAY value This is the record latency of the video server Typical value is 3 frames Select the destination Video Server Channel The destination channel may be any VTR except VTR6 a Press VTR 6 to initiate the Capture function b Set an IN point on the SOURCE VTR Jog Shuttle to the desired IN point Press IN OR Press SHIFT IN Manually enter the IN time on the numeric keypad Press ENTER Set OUT point the SOURCE VTR Jog Shuttle to the desired OUT point Press OUT OR Press SHI FT OUT Manually enter the OUT time the numeric keypad Press ENTER d Press SHIFT RECORD The display will prompt for a CLIP ID Manually enter a ID maximum of 8 characters using the numeric keypad the Shotbox QWERTY keyboard or PC keyboard Press ENTER to accept the entered CLIP ID The SOURCE VTR will preroll to its IN point then play The video server will start recording at the SOURCE s IN point and stop recording at the SOURCE s OUT point The created clip will be loaded on the destination channel 2044CL O 6 300 Clip Instant Access System 16 19 VIEW SHOTKEY ASSIGNMENTS ON THE SHOTBOX a Press and hold VIEW The VIEW
8. 0 57400 V5 30 and up 3 Press a key that corresponds to the version of the ST400 that you are using 2044CL O 6 300 Clip Instant Access System 26 25 KEY LAYOUT ST400 VTR DDR Controller Fle e N SIEUT 2044CL O amp 4040CL O T amp PBIO 2044CL O 6 300 Clip Instant Access System 26 DNF CONTROLS LI MI TED WARRANTY DNF Controls warrants its product to be free from defects in material and workmanship for a period of one 1 year from the date of sale to the original purchaser from DNF Controls In order to enforce the rights under this warranty the customer must first contact DNF s Customer Support Department to afford the opportunity of identifying and fixing the problem without sending the unit in for repair If DNF s Customer Support Department cannot fix the problem the customer will be issued a Returned Merchandise Authorization number RMA The customer will then ship the defective product prepaid to DNF Controls with the RMA number clearly indicated on the customer s shipping document The merchandise is to be shipped to DNF Controls 12843 Foothill Blvd Suite D Sylmar CA 91342 USA Failure to obtain a proper RMA number prior to returning the product may result in the return not being accepted or in a charge for the required repair DNF Controls at its option will repair or replace the defective unit DNF Controls will return the unit prepaid to the customer The met
9. 12843 Foothill Blvd Suite D Sylmar CA 91342 818 898 3380 voice 818 898 3360 fax E fs www dnfcontrols com Model 2044CL O 8 amp 2044CL O T 8 300 CLIP INSTANT ACCESS SYSTEM Odetics Protocol User Manual Table of Contents 1 REVISION HISTORY GETTING STARTED 2 SYSTEM DESCRIPTION DEFINITIONS 3 SYSTEM INSTALLATION a SHOTBOX b ST400 S SM VTR DDR CONTROLLER 4 VIDEO SERVER SETUP 5 LOAD ON THE ST400 6 LEARN A CLIP OR CLIP COMBINATION a ON THE ST400 b ON THE SHOTBOX 7 RECALL A CLIP OR CLIP COMBINATION a ON THE ST400 b ON THE SHOTBOX 8 RECUE CLIP 9 REALIGN GANGED CHANNELS 10 CLEAR CUE POINTS a ON THE ST400 b ON THE ST420 SHOTBOX 11 PLAY CLIP a ON THE ST400 b ON THE SHOT BOX 12 LOOP CLIP ON THE ST400 13 TIMECODE SEARCH 14 BVW MODE ADVANCED FEATURES 15 SHOTBOX SHOTKEY MAPPING TO SHOTLIST LOCATIONS 16 SHOTBOX CONTROL SWITCHES 17 CREATING A CLIP ON THE ST400 18 CAPTURE 19 VIEW SHOTKEY ASSIGNMENTS ON THE SHOTBOX 20 CREATE CUE POINT LABELS ON THE ST400 2044CL O 6 300 Clip Instant Access System REFERENCE 21 SETUP MENU 22 FUNCTION TABLE 23 SPECIFICATIONS a ST400 b ST420 SHOTBOX 24 TROUBLESHOOTING ST420 TROUBLESHOOTING 25 KEY LAYOUT 26 DNF CONTROLS LIMITED WARRANTY Manual 1 21 051706
10. 2v 1 0A 12V 0 6A Size L x W x H 12 3 4 x 8 x 1 3 4 front 3 5 8 rear 8 5 8 high to top of display Weight 10 Ibs Rear Panel Connectors 2 3 4 5 6 All DB9F DBF25F Power DB9M SHOTBOX DB9F PBIO DB9F Keyboard 6 pin mini DIN Ref Video In BNC Ground Threaded stud Display Easy to read back lit LCD display Jog Shuttle Wheel With mechanical detents RS422 SERI AL CONNECTOR 9 Pin D Type Female DB9F Pin 1 Frame Ground 2 Receive A 3 Transmit B 3 4 Transmit Common 5 Spare POWER CONNECTOR 9 Pin D Type Female DB9M Pin 1 5v DC 2 5v DC 3 Ground 4 12 VDC 5 12 VDC 2044CL O 6 300 Clip Instant Access System CON OND Receive Common Receive Transmit A gt Frame Ground 5 VDC Ground Ground Ground 23 GPI I N OUT CONNECTOR 26 Pin D Type Female DB26F I N I N Pin OUT Function Pin OUT Function 1 OUT GPO 0 No function 14 IN LAST CUE 2 OUT GPO 1 No function 15 IN RECALL CUE 3 OUT GPO 2 No function 16 No Connection 4 OUT GPO No function 17 No Connection 5 OUT GPO 4 No function 18 Ground 6 OUT 5 No function 19 5V 7 OUT 6 No function 20 5V 8 OUT GPO 7 No function 21 No Connection 9 Ground 22 No Connection 10 IN PLAY 23 No Connection 11 IN STOP 24 No Connection 12 IN RECUE 25 No Connection 13 IN NEXT CUE 26 Ground 2044CL O 6 300 Clip Instant Access System b 51420 SHOTBOX Power
11. 6 key or VTR7 or VTR8 softkey b Press CLIP LIST to view the list of 10 that are resident on the Video Server The CLIP LIST indicator will turn on Press CREATE to create load a new clip Creating a clip is described in the CREATING A CLIP section OR Turn the Wheel to view the existing CLIP IDs on the video server Turn the Wheel clockwise to scroll forward or counter clockwise to scroll backward through the list of available CLIPs Backward scrolling is limited to the last 10 screens of CLIP 165 Press LOAD to load the highlighted CLIP ID After loading the selected clip the CLIP LIST function will terminate The CLIP LIST indicator will turn off OR Press ENTER to manually enter a Clip ID using the ST400 numeric keypad or Shotbox QWERTY keyboard or PC keyboard Press ENTER to load the entered CLIP ID for playout OR Press ENTER on PC keyboard d Repeat steps a c to load clips on desired VTRs 2044CL O 6 300 Clip Instant Access System 7 6 LEARN CLIP CLIP COMBINATION a ON THE ST400 1 ODETICS PROTOCOL a Press VTR 1 2 3 4 5 or 6 key or VTR7 or VTR8 softkey to select the channel to learn Load a clip on the selected channel See Section LOAD A CLIP Use the transport functions to view the clip Press IN to mark an IN point The IN LED will turn on On recall the clip will cue to the IN time not the beginning of the clip
12. PDATE When exiting SLOMO mode the last used speed is saved in the Preset Speed register STATIC The Preset Speed register is NOT updated when exiting SLOMO mode It is only changed by SHIFT SLOMO PRESET SLOMO Press SPD RNG softkey to toggle between SLOMO speed ranges 0 gt 1 OR 02 2x RECALL Press NORMAL or REDIRECT MODE REDIRECT When one and only one clip is learned into a Cue Point the Clip will be REDIRECTED to load on the currently selected VTR NORMAL The cue point will load on the learned VTR GANG PERM Permanent Gang MODE The GANG can be created and undone only with the GANG softkey TEMP Temporary Gang Quickly create a GANG by pressing and holding a VTR key then pressing other VTR keys Quickly undo the GANG by pressing any VTR key Video Reference must be connected for frame accurate playout of ganged channels 2044CL O 6 300 Clip Instant Access System 19 PARAMETER DESCRIPTION RECORD Enter delay value Used by CAPTURE function DELAY PREROLL Enter Preroll value DESTINATION Select VTR1 VTR2 VTR3 VTR4 or VTR5 to be the CHANNEL destination recorder channel for Capture Function SELECT VTR6 cannot be selected REF VI DEO Select the appropriate softkey to enable or disable the reference video Set each channel as required Select NOT SUPPORTED to have TC search on the GVG servers or SUPPO
13. PPLY APX 4108 into the POWER connector on the rear of the ST400 Plug the Power Supply into an outlet 90 VAC 240 VAC Attached Video Ref cable from House Ref to Ref Video in the rear of the ST400 to utilize the capture function or the gang function Video Reference must be connected for frame accurate playout of ganged channels and for Capture function Check SETUP MENU prior to using the ST400 to confirm proper Record mode and other User settable modes Installation is complete 2044CL 8 Connection Diagram 57400 Controller VTRs 52252 t POWER SUPPLY 2044CL O 6 300 Clip Instant Access System 4 VIDEO SERVER SETUP a Select ODETICS Broadcast communications protocol on the VIDEO SERVER to be controlled b Assign a serial port on the VIDEO SERVER through which the ST400 will control it NOTES The VIDEO SERVER may not support LTC or VITC time modes in ODETICS Broadcast mode The ST400 will default to Tape Time if a non supported time mode is selected In ODETICS Broadcast mode the VIDEO SERVER may ONLY allow Full Record INSERT and ASSEMBLE record modes may be disabled The Grass Valley Group PROFILE does not support search to a time location using Timecode LTC or VITC in ODETICS Protocol Tape Time mode TM must be selected on the ST400 5 LOAD ON THE ST400 a Select a VTR by pressing VTR 1 2 3 4 5 or
14. RTED for all other servers LEARN Press softkey to select CLEAR ON The IN and OUT points will be cleared after the cue is learned OR OFF The IN and OUT points will remain after the cue is learned SERVICE DEFAULTS SOFTKEY Set ST400 to factory defaults Follow the prompts on the display CLEANUP Deletes all cue points Follow the prompts on the display Press ENTER to continue or press ESC to exit without changing ST400 2044CL O 6 300 Clip Instant Access System 20 22 FUNCTION TABLE B ls Press TO OUT OUT I OUT point is marked cue to the OUT point POINT FFWD Press and HOLD to shuttle Release key to stop Set WIND Speed in MENU GOTO SHIFT RECUE Search the VTR to the manually entered time ENTERED TIME Use the ST400 numeric keypad Press ENTER or RECUE GANG SETUP GANG Individually press the VTR keys to be included in the gang The LED above the key will turn on Press the VTR key again to remove from gang The LED above the key will turn off Press ESC to exit Upon exiting all members of the gang will have their VTR LEDs turned on The flashing LED shows which VTR is currently selected LAST CUE LAST Step to the previous Cue Point Location to the previous Cue Point Location LOOP LOOP ENABLE NN the currently loaded clip a continuous loop NEXT CUE NEXT Step to the next Cue Point Location RECORD REC Places VTR into th
15. clip Optional Press OUT to mark an OUT point The OUT LED will turn on On recall the clip will play to the OUT point then stop To delete an IN or OUT point press and hold DEL then press IN or OUT The IN OUT LED will turn off If no IN point is marked the current location of the clip will be learned as the IN point d For GANGs repeat steps a and b for each channel Then press the GANG softkey Press VTR 1 2 4 5 or 6 key or VTR7 or VTR8 softkey to add it to the GANG The VTR LED will turn on Press the VTR key again to remove it from the gang The VTR LED will turn off Press ESC to exit GANG mode The LEDs of all GANGed VTRs will turn on 2 THEN PERFORM FOLLOWING ON THE SHOT BOX a Press LEARN The LEARN indicator will turn on b Select the desired BANK by pressing BANK 1 2 3 4 5 6 7 8 9 or 0 Press the desired Shotkey to complete the learn process The learned CLIP ID is displayed on the Shotkey d Press ESC at anytime to escape without LEARNing 2044CL O 6 300 Clip Instant Access System 10 7 RECALL CLIP OR CLIP COMBINATION a ON THE ST400 1 Select the desired Cue Point by pressing NEXT CUE LAST CUE or by manually entering the Cue Point using the numeric keypad The selected Cue Point number is shown on the bottom of the display 2 Press LOAD on the ST400 The ST400 will automatically load the Learned clips on
16. connector Size rear Weight Rear Panel Connectors RS422 SERIAL CONNECTOR 90 VAC to 265 VAC adapter supplied with IEC AULT Model SW300 5v 3 5A 12v 2A 12v 0 8A L XW x H 11 5 x 6 5 x 1 75 front 3 5 4 165 9 Pin D Type Female Pin 1 POWER CONNECTOR Frame Ground Transmit A 3 Receive Receive Common Spare 9 Pin D Type Male 5v DC 5v DC Ground No Connection No Connection 2044CL O 6 300 Clip Instant Access System Out GPI Power Aux DBF15F DB9M Transmit Common Transmit 3 Receive Frame Ground No Connection Ground Ground Ground 25 24 TROUBLESHOOTING 57420 TROUBLESHOOTING All Shotkeys are RED communication with the 57400 All Shotkeys DARK communication between the 57400 and the Video Server Set the ST420 version to match the 57400 On the ST420 V4 02 V4 03 V4 12 V4 13 1 Press SHIFT STOP PLAY The key that displays the current version is RED 2 The ST420 displays ST300 400 SELECT ST300 V2 X ST300 V3 X ST400 2044CL O ST400 2044CL L 3 Press the ST400 2044CL O key for communication with the ST400 On the ST420 V4 04 V4 14 and above 1 Press SHIFT STOP PLAY The key that displays the current version is RED 2 The ST420 displays ST300 400 SELECT ST300 V2 X ST300 V3 X 57400 V4 X V5 2
17. e Record mode selected by RECORD MODE in the SETUP MENU Press SHIFT RECORD sev and HOLD to shuttle Release key to stop O sa WIND Speed in MENU SHUTTLE Select SHUTTLE mode and enable Wheel SLOMO Press SLOMO to slo mo the VTR Turn the Wheel or move the T Bar if available to change the play speed Press SLOMO to STILL frame OR press any transport key to exit SLOMO SLO MO SHIFT For WHEEL ONLY Press SHIFT SLOMO to SPEED SLOMO preset the slo mo speed Turn the Wheel to select PRESET desired speed Press ESC or any transport key to exit STOP STOP Press once to STILL frame VTR Press again to put VTR into STOP mode 2044CL O 6 300 Clip Instant Access System 21 Press Description TIME ME MODE Press to toggle between Timecode TC VITC VT SELECT or Tape Timer TM display modes PLAY PLAY If an OUT point is marked play to the OUT point and stop If not OUT point is marked play normally If the CLIP ID ends with do loop play PLAY SIMPLE SHIFT PLAY Play to end of clip not Out Point RECUE RECUE If the IN point is marked cue to the IN point If IN point is not marked cue to the beginning of the clip Under BVW protocol no action occurs 2044CL O 6 300 Clip Instant Access System 22 23 SPECIFICATIONS a 1400 Power 90 to 265 VAC adapter supplied with IEC connector APX Model AP4108 5v 4A 1
18. hod of shipment is at the discretion of DNF Controls principally UPS Ground for shipments within the United States of America Shipments to international customers will be sent via air Should a customer require the product to be returned in a more expeditious manner the return shipment will be billed to their freight account This warranty will be considered null and void if accident misuse abuse improper line voltage fire water lightning or other acts of God damaged the product repair parts are to be supplied by DNF Controls either directly or through its authorized dealer network Similarly any repair work not performed by either DNF Controls or its authorized dealer may void the warranty After the warranty period has expired DNF Controls offers repair services at prices listed in the DNF Controls Price List DNF Controls reserves the right to refuse repair of any unit outside the warranty period that is deemed non repairable DNF Controls shall not be liable for direct indirect incidental consequential or other types of damage resulting from the use of the product 43 dd 2044CL O 6 300 Clip Instant Access System 28
19. ng NEXT CUE LAST CUE or by manually entering the Cue Point using the numeric keypad The selected Cue Point number is shown on the bottom line of the display Locate the clip to the desired IN time Press IN to mark the IN time Locate the clip to the desired OUT time Press OUT to mark the OUT time Press SHIFT MARK to start the LEARN The first line of the display will show Select VTRs The second line of the display will show Mark Lrn ESC cancel Press VIR 1 VTR 2 41 VTR 5 or VTRL 6 key or VTR7 or VTR8 softkey to select the VTR to be learned into the current Cue Point If the VTRs are ganged select VTR that is part of the Gang The rest of the Gang will learn automatically Press MARK to complete the LEARN NOTE Learn will overwrite the previous contents of the Cue Point OR Press ESC to exit without LEARNING The ST300 will LEARN save the VTR number 1 2 3 4 5 6 and current IN amp OUT time to the selected Cue Point b ON THE SHOTBOX 1 PERFORM FOLLOWING ON THE ST400 FIRST a Press VIR 1 2 4 5 or 6 key VTR7 or VTR8 softkey to select the channel to learn b Load a clip on the selected channel See section LOAD A CLIP Use the transport functions to view the clip Press IN to mark an IN point The IN LED will turn on On recall the clip will cue to the IN time not the beginning of the
20. ows BANK 0 Shotkeys 1 gt 30 access cue point locations 001 gt 030 BANK 1 Shotkeys 1 gt 30 access cue point locations 101 gt 130 BANK 2 Shotkeys 1 gt 30 access cue point locations 201 gt 230 BANK 3 Shotkeys 1 gt 30 access cue point locations 301 gt 330 BANK 4 Shotkeys 1 gt 30 access cue point locations 401 gt 430 BANK 5 Shotkeys 1 gt 30 access cue point locations 501 gt 530 BANK 6 Shotkeys 1 gt 30 access cue point locations 601 gt 630 BANK 7 Shotkeys 1 gt 30 access cue point locations 701 gt 730 BANK 8 Shotkeys 1 gt 30 access cue point locations 801 gt 830 BANK 9 Shotkeys 1 gt 30 access cue point locations 901 gt 930 SHOTBOX CONTROL SWITCHES PLAY Plays out the selected clip RECUE Returns to the beginning of the clip STOP Stops playout of the clip CREATING A CLIP ON THE ST400 Press CLIP LIST Press CREATE The display will show the default CLIP ID Manually enter ID with a maximum of 8 characters from the ST400 numeric keypad OR a PC keyboard OR the Shotbox QWERTY keyboard NOTE For numbers on the SHOTBOX keyboard use bank keys O 9 Press CREATE The clip will be created with the entered CLIP ID If the selected CLIP ID already exists a warning message will be displayed Press any key to continue 2044CL O 6 300 Clip Instant Access System 15 18 CAPTURE This function allows clips to be recorded on to the Video Server from
21. ping NOTES If the CLIP ID ends with an asterisk or a hash mark it will automatically loop when either LOOP ENABLE or PLAY is pressed Loop Clip will only work from the 2044CL Loop Clip will not affect clips loaded from the user Interface 13 TIMECODE SEARCH In order to properly search by Timecode please select Timecode NOT SUPPORTED menu option for every channel connected to the Profile and Timecode SUPPORTED for all other channels To select Timecode option Press MENU key Turn the wheel until TI MECODE option is highlighted Press CHANGE softkey Press a softkey to select SUPPORTED or NOT SUPPORTED setting Press ESC twice to exit menu mode 2044CL O 6 300 Clip Instant Access System 13 14 BVW If you wish to control a tape machine a DDR with the 2044CL O system select control MODE BVW see Setup Menu section In this mode the media is accessed by timecode by clip names The cuepoints in mode consist only of IN point OUT point and Gang information The following functions are not available BVW mode View Clip ID Recue Clip Loop Clip Capture Create Clip All other functions work as described in the manual 2044CL O 6 300 Clip Instant Access System 14 Advanced Features 15 SHOTBOX SHOTKEY MAPPING TO SHOTLIST 16 17 LOCATIONS The Shotkeys on the Shotbox access the cue point locations in the ST400 as foll
22. t setting Press the EXIT softkey to exit the Setup Menu PARAMETER DESCRIPTION PROTOCOL Set each channel as required Select ODETICS or BVW ODETICS Select Odetics to allow clip functionality Load Create Recue View available Clips BVW Select BVW to control video server like In this mode the clip must have already been loaded STANDARD Press NTSC DF or PAL to select the video standard for time calculations WIND MODE Press Softkey to select HOLD fast wind is maintained only while key is depressed OR LATCH fast wind is maintained after key is released Set the fast wind speed 3 9 to 23 7 by pressing the SPEED softkey Set each channel as required RECORD MODE Set each channel as required Press softkey to select to select the desired record mode Lockout Crash Full 2044CL O 6 300 Clip Instant Access System 18 PARAMETER DESCRI PTI ON SLOMO Press the TBAR WHEEL softkey to select the T bar or wheel for slomo For T bar The T BAR has a speed range of 0 gt 2x with a detent at 1x play speed OR a range of 0 gt 1x detent at 1x Play speed Press SPD RNG softkey to toggle between SLOMO speed ranges 0 1 OR 02 2x Press BACK softkey to return to SLOMO MENU Press ESC to exit OR turn the Wheel to select another item For Wheel Press the PRSET sofkey to toggle between UPDATE and STATIC modes U
Download Pdf Manuals
Related Search