OPERATOR`S MANUAL Tiller/Cultivator
Contents
1. EARTH The Clean Alr Choice Peer de E F Ea d E r i r Ma a a OPERATOR S MANUAL Tiller Cultivator This product is covered by U S patents and other international patents Copyright All Rights Reserved Model TC70001 ea 244026 This product has been engineered and manufactured to our high standard for dependability ease of operation and operator safety Properly cared for it will give you years of rugged trouble free performance A WARNING To reduce the risk of injury the user must read and understand the operator s manual before using this product Thank you for your purchase DO NOT RETURN THIS PRODUCT TO THE STORE OPERATING ASSEMBLY PARTS SERVICE QUESTIONS CALL 1 800 313 5111 BETWEEN 7 30AM 4 30PM EST FOR ASSISTANCE SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS Product Specifications o o oooooo o 2 Maintenance 0 aaa 9 Symbols a 3 SIONS sia wad crga AA O ON a AA AA 10 Safety Warnings a 4 5 Troubleshooting 0 00 cee eee ee 10 Assembly Lo 6 Warranty 0 aaa 11 Operating 0 2 aaa 7 8 PRODUCT SPECIFICATIONS Model TC70001 Power supply voltage 120V 60HZ Working width 11 Idle Speed 320 RPM Working depth max 8 Power Consumption 8 5 Amp Parts List O aanib Y anO Switch and power cable assy RTC00057 Wheel RTC00042 Cm a 7T Wing nut RTC00054 Tine Assembly right R2. If the tiller cultivator strikes a foreign body turn it off immediately wait for the tines to stop and check for damage lf necessary repair before restarting If the tiller cultivator starts to vibrate abnormally turn it off immediately and check for the cause Vibration is generally a warning of trouble DANGER RISK OF CUT Wear gloves and use caution when cleaning or performing maintenance on the tiller cultivator Always turn off the tiller cultivator disconnect from the power supply and wait until the tines come to a complete stop before carrying out any maintenance or repairs CAUTION Tines do not stop immediately after the tiller cultivator is turned off CAUTION Risk of injury Do not put hands feet or any body part or clothing near the rotating tines WARNING California Proposition 65 This product contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm WARNING Some dust and debris created by the use of this tool could contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Some examples of these chemicals are chemicals in fertilizers compounds in insecticides herbicides and pesticides arsenic and chromium from chemically treated lumber Your risk from exposure to these chemicals varies depending on how often you do this type of work To reduce your exposure work in a well ventilated
3. Fig 2 7 WARNING If any parts are damaged or missing do not operate this product until the parts are replaced Failure to heed this warning could result in serious personal injury Call our customer service help line at 1 800 313 5111 for assistance WARNING Do not attempt to modify this product or create accessories not recommended for use with this product Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury WARNING Do not connect to power supply until assembly is complete Failure to comply could result in accidental starting and possible serious personal injury 2 1 M5 X 12 OPERATING STARTING Make sure the wheel frame is raised before you start the tiller To raise the frame pull out the lock pin Step A rotate the wheel frame upward beyond the lock button on the back of the motor housing Step B release the lock pin The wheel frame will be locked in place by the lock button See Fig 3 3 Val gt gt Secure the extension cord into the cord retainer 5 The loop of the extension cord must be long enough for the cord retainer to freely slide from one side to the other Plug the extension cord into the power cord plug on the tiller Use the tiller cultivator for breaking sod preparing seed beds and for cultivating gardens and flower beds The tiller cultivator can also dig small holes for planting sap
4. area and with approved safety equipment such as dust masks that are specially designed to filter out microscopic particles ASSEMBLY This product must be assembled correctly before use 1 Remove the screws M5 X 12 and washers from wheel frame Insert the wheels on the axle of wheel frame then attach washers and screws M5 X 12 to secure Fig 2 1 Press the wheel covers into the wheel and cover the ends of the axles You may use a hammer to seat them securely into the wheels Fig 2 1 To lower wheel frame push the lock button on back of motor housing to release the frame Step A Low er the wheel frame Step B and pull out the lock pin on lower handle section Step C Align lock pin to the hole in wheel frame then release it to lock the wheel frame in position Fig 2 2 Slide the cord retainer 5 onto the center handle section 4 Fig 2 3 Attach the center handle section 4 to the lower handle sections 9 using the two supplied M6 X 45 bolts 6 and wing nuts 7 Fig 2 4 Fasten the upper handle section 1 to the center handle section 4 using the two supplied M6 X 45 bolts 6 and wing nuts 7 Fig 2 5 2 Tre ml a CAP Huai NAA Na Y 65 Seo a INN Bi 7 Install the switch and power cable assembly onto the upper handle section using the two supplied bolts ST3 9 x 19 Fig 2 6 8 Use the two supplied cable clips 3 to secure the cord
5. Set to correct working depth Worn blades Replace damaged or worn blades CALL US FIRST Call us first with questions about operating or maintaining this product at 1 800 313 5111 between 7 30 a m 4 30 p m Eastern Standard Time or send emails to earthwise reelin com EARTH WSL The Clean Air Choice The Great States Corporation American Lawn Mower Company 830 Webster Street Shelbyville IN 46176 www americanlawnmower com 10 WARRANTY This product is manufactured for The Great States Corporation American Lawn Mower Company The Great States Corporation American Lawn Mower Company Shelbyville Indiana has been making lawn mowers for over 100 years and it warrants to the original owner that each new product and service part is free from defects in material and workmanship and agrees to repair or replace under this warranty any defective product or part from the original date of purchase for two 2 years except for the conditions and circumstances listed below Proof of purchase original dated sales receipt must accompany all warranty claims THIS WARRANTY IS NOT TRANSFERABLE AND DOES NOT COVER Products sold damaged or incomplete sold as is sold reconditioned or used as rental equipment Delivery installation or normal adjustments explained in the operator s manual Damage or liability caused by shipping improper handling improper installation incorrect voltage or improper wiring improp
6. if the tiller cultivator is not of children being used for longer than a month wipe over all metal surfaces with an oil impregnated cloth to protect them During extended periods of storage ensure that the tiller from corrosion or spray with a fine coat of oil Fold the cultivator is protected against corrosion and frost guide bar down and store the tiller cultivator in a suitable place TROUBLESHOOTING Motor does not start Unit not plugged in Plug in the unit No electricity Check power supply Defective cable Check cable Repair or replace if required Defective safety switch plug Arrange for repair Overheat protection activated 1 Working depth too large set to a shorter depth 2 Blades blocked remove the blockage 3 Soil too hard select correct work depth and move forward and backward several times while slowing down the operation speed Wait until the motor cools down for about 15 minutes before further use Abnormal noises Blade is jammed Switch off Wait till tines comes to a complete stop Remove jammed objects Lubrication running out Tiller cultivator must be repaired Call our customer service help line at 1 800 313 5111 for assistiance Bolts nuts or other components are Tighten all components Arrange for repair if noises loose continue Abnormal vibrations Blades damaged or worn Replace damaged or worn blades Working depth too large Set to correct working depth Poor results Working depth too small
7. precautions should always be followed to reduce risk of fire electric shock and personal injury including the following READ ALL INSTRUCTIONS GENERAL SAFETY CHECK FOR DAMAGED PARTS Before further use of the product any part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and any other condition that may affect its operation Any part that is damaged should be properly repaired or replaced For assistance call our customer service help line at 1 800 313 5111 AVOID DANGEROUS ENVIRONMENTS Don t use this product in rainy stormy damp or wet locations Do not operate in gaseous or explosive atmospheres Motors in these products normally spark and the sparks might Ignite fumes KEEP CHILDREN AWAY All visitors children and pets should stay at a safe distance from the work area DRESS PROPERLY Don t wear loose clothing or jewelry and wear protective hair covering to contain long hair They can be caught in moving parts Use of rubber gloves and substantial footwear is recommended when working outdoors USE SAFETY GLASSES Wear safety glasses with side shields or goggles that are marked to comply with ANSI Z87 1 standard when operating this product Use face or dust mask if environment is dusty DOUBLE INSULATION The tiller cultivator has double insul
8. TC00025 left RTC00036 SQ E SYMBOLS Some of the following symbols may be used on this product Please study them and learn their meaning Proper interpretation of these symbols will allow you to operate the product better and safer Precautions that involve your safety Read the instruction manual and follow the warning and safety instructions SWITCH OFF Remove plug from outlet immediately if the cable is damaged or cut POL SWITCH OFF Remove plug from outlet before cleaning or maintenance 7 Do not use in wet weather conditions Wear eye and ear protection Keep bystanders at a safe distance DANGER Rotating blades Keep hands and feet at a safe distance US DANGER Of being hit by thrown objects Waste electrical products should not be disposed of with household waste Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice HA TO REDUCE RISK OF INJURY Before any use be sure everyone using this product reads and understands all safety instructions and other information contained in this manual CAUTION Wear appropriate personal hearing protection during use Under some conditions and duration of use noise from this product may contribute to hearing loss TUN IMPORTANT SAFETY WARNINGS N Save these instructions and review frequently prior to use and in instructing others WARNING When using electric gardening appliances basic safety
9. ation This means that all external met al parts are insulated from the electrical supply This is achieved by introducing an insulation layer between electrical and mechanical parts The double insulation guarantees you the greatest possible safety EXTENSION CORD Make sure your extension cord is in good condition When using an extension cord be sure it is heavy enough to carry the current your product will draw An undersized extension cord will cause a drop in line voltage resulting in loss of power and overheating The following table shows the correct size to use depending on cord length and nameplate ampere rating If in doubt use the next heavier gage The smaller the gage number the heavier the cord Minimum Gage for Cord Sets Total Length of cord in Feet 0 25 26 50 51 100 101 150 0 50 51 100 101 200 201 300 Ampere Rating More Not More Than Than American wire Gage 16 14 14 12 14 12 Not Recommended WARNING Use outdoor extension cords marked SW A SOW A STW A STOW A SJW A SJTW A or SJTOWA These cords are rated for outdoor use and reduce the risk of electric shock It is possible to tie the extension cord and power cord in a knot to prevent them from becoming disconnected during use Make the knot as shown then connect the plug end of the power cord into the receptacle end of the extension cord This method can also be used to tie two extension cords together Be aware of the extension cord
10. ce operations disconnect power supply Before each use check the extension cord for Replace worn or damaged parts with original signs of damage or ageing Replace the cable if replacement parts only Parts from another tiller it is cracked split or otherwise damaged Check the cultivator may not fit properly causing an unsafe condition of the tines and ensure that all threaded situation connections are securely tightened If the tines become dull or blunt sharpen or replace them Call Make sure all protective devices are secure and in our customer service help line at 1 800 313 5111 good condition Repair or replace if necessary for assistance Lubrication Fig 7 The tines drive transmission Once per season lubricate the tines and shaft At case has grease installed at the factory It is not the end of the season check the tiller cultivator for required that the grease level be checked nor damage prior to storing Repair or replace damaged recommended that grease be added during the or broken parts first 2 years of use After the second season of use follow the directions as described below AN CAUTION Always clean the tiller cultivator after each use Failure to carry out proper cleaning can result in damage to the tiller cultivator or result in poor performance M10 X 6 Clean the underside of the motor support plate and housing around the tines with a scrub brush and a soft cloth dampened with a mild soap and water
11. cultivator over the extension cord Make sure the cord is always in a safe position behind you When working on inclines always stand diagonally to the incline to retain a firm safe footing Do not work on extremely steep slopes OPERATING For preparing seed beds we recommend using one of these tilling patterns Tilling Pattern A Make two passes over area to be tilled the second at a right angle to the first Before use remove any visible stones or other foreign bodies from the area CAUTION Before moving the tiller cultivator from one area to another switch off the motor and wait for the tines to come to a complete stop Be careful not to let the tines touch the ground while moving the tiller cultivator The tines as well as the unit itself may be damaged even if the motor is switched off Tilling Pattern B Make two passes over area to be tilled the second overlapping the first Clearing foreign objects During operation a stone or root could become lodged in the tines or tall grass or weeds may become wrapped around the tine shaft To clear the tines or tine shaft release the trigger lever wait for the tines to come to a complete stop and unplug the tiller cultivator Dislodge or remove the foreign matter from the tines or tine shaft To simplify removal of tall grass or weeds from the tine shaft remove one or more of the tines See Tine Removal and Installation MAINTENANCE Before carrying out maintenan
12. e record your serial number in the space provided below e NAME OF ITEM Tiller Cultivator e MODEL NUMBER TC70001 e SERIAL NUMBER The Great States Corporation American Lawn Mower Company 830 Webster Street Shelbyville IN 46176 Phone 1 800 313 5111 www americanlawnmower com In a continued commitment to improve quality the Manufacturer reserves the right to make component changes or design changes when necessary Rev 2013 09 17 EARTHS A The Clean Air Choice CL MANUAL DEL OPERARIO Rotocultivador Este producto esta amparado por patentes de EE UU y otras patentes internacionales si A Copyright Todos los derechos reservados Modelo TC70001 ea 244026 Este producto fue disenado y fabricado de acuerdo con nuestros altos estandares de confiabilidad facilidad de operacion y seguridad para el operario Si se trata con cuidado esta herramienta le otorgar a os de ptimo rendimiento y resistencia A ADVERTENCIA Para reducir el riesgo de sufrir alguna lesi n el usuario debe leer y comprender el manual del operario antes de usar este producto Muchas gracias por su compra NO DEVUELVA ESTE PRODUCTO A LA TIENDA TIENE PREGUNTAS SOBRE EL FUNCIONAMIENTO EL MONTAJE LAS PIEZAS Y EL MANTENIMIENTO LLAME AL 1 800 313 5111 ENTRE LAS 7 30 Y LAS 16 30 HORA DEL ESTE DE LOS ESTADOS UNIDOS GUARDE ESTE MANUAL PARA CONSULTAS FUTURAS
13. er maintenance improper modification or the use of accessories and or attachments not specifically recommended Repairs necessary because of operator abuse or negligence or the failure to install operate maintain or store the product according to the instructions in the operator s manual Damage caused by cold heat rain excessive humidity corrosive environments and materials or other contaminants Expendable items that become worn during normal use Cosmetic defects that do not interfere with product functionality Freight costs from customer to vendor Repair and transportation costs of products or parts determined not to be defective ANY INCIDENTAL INDIRECT OR CONSEQUENTIAL LOSS DAMAGE OR EXPENSE THAT MAY RESULT FROM ANY DEFECT FAILURE OR MALFUNCTION OF THE PRODUCT Some states do not allow the exclusion or limitation on how long an implied warranty lasts so the above limitations may not apply to you ANY NON RESIDENTIAL USE OR COMMERCIAL USE VOIDS ALL WARRANTIES MEA SE EARTR OG The Clean Air Choice OPERATOR S MANUAL Tiller Cultivator This product is covered by U S patents and other international patents Copyright All Rights Reserved SERVICE Now that you have purchased your Tiller Cultivator should a need ever exist for repair parts or service simply contact us at 1 800 313 5111 Be sure to provide all pertinent facts when you call or visit REPAIR PARTS Pleas
14. lings or potted plants Move the tiller cultivator to the work area prior to starting the motor To lower wheel frame push the lock button on back of motor housing to release the frame Lower the wheel frame and pull out the lock pin on lower handle section Align lock pin to the hole in wheel frame then release it to lock the wheel frame in position See Fig 2 2 Hold the tiller cultivator firmly while starting The tines will pull the tiller cultivator forward during operation Lower the tines slowly with the guide bar To start the tiller cultivator press and hold the safety lock button A on the safety switch while pulling the trigger lever B up and against the handle bar The motor will start and the tines will begin to rotate To stop the tiller cultivator simply release the lever For breaking sod or deep tilling allow the tines to pull the tiller cultivator forward to the end of your arm s reach then firmly pull it back toward yourself You will achieve the best results by repeatedly allowing it to move forward and pulling it back By pulling the tiller cultivator back towards yourself the tines will dig deeper and more aggressively To prevent tripping take extra precautions when moving backwards and when pulling the tiller cultivator back toward yourself If the tiller cultivator digs deep enough to stay in one spot gently rock it side to side until it starts moving forward again Never pass the tiller
15. mixture Never use a water hose to clean the till er To remove soil and debris from the trans mission and tines use a stiff brush ora damp ened cloth Clean the vents on the motor housing and remove any remaining grass or dirt Once cleaned wipe the tines and shaft dry and apply a light coat of oil to prevent rust Tines Removal and Installation Fig 6 Worn tines invite poor performance and overload of the motor Check tines before each use Sharpen or replace the tine assemblies with new ones when Drain screw plugs are located on the right side of necessary Call 1 800 313 5111 for assistance transmission housing Lay the tiller cultivator on its left side and clean the transmission of dirt and debris prior to removing the drain screw plugs If necessary remove tine assemblies to have better access to the drain screw plug Use a 5mm hex key to unscrew the plugs Using a squeeze bottle or tube add approximately 2 4 oz 70ml of auto gear lube Do not overfill When completed reinstall both drain screw plugs into the transmission N WARNING Injury can occur while working on the tines Wear protective gloves To remove the complete tine assemblies from the shaft remove the M8 X 40 hex head bolt from the shaft Remove the tine assembly from the shaft Reverse above steps to install tines STORAGE Store the Tiller Cultivator in a dry clean area out of reach At the end of the season or
16. while operating the tiller cultivator Be careful not to trip on the cord Always guide the cord away from the tines OVERHEAT PROTECTION If the tiller cultivator is blocked by a foreign object or if the motor is overloaded the motor will switch off automatically by the protection device Release the trigger lever and wait for the motor to cool down approx 15 minutes before starting the tiller again GENERAL SAFETY GROUND FAULT CIRCUIT INTERRUPTER GFCI protection should be provided on the circuit or outlet to be used for the tiller cultivator Receptacles are available having built in GFCI protection and may be used DISCONNECT UNIT from the power supply when not in use or when servicing or cleaning Do not leave unattended DON T ABUSE CORD Never carry this product by the cord or yank the cord to disconnect from the receptacle Keep cord from heat oil and sharp edges USE RIGHT APPLIANCE Do not use this product for any job except that for which it is intended DON T OVERREACH Guide the tiller cultivator at a walking pace only Keep proper footing and balance at all times LIGHTING Only operate your tiller cultivator in daylight or good artificial light STORE IDLE UNIT INDOORS When not in use the tiller cultivator should be stored indoors in a dry area out of children s reach MAINTAIN UNIT WITH CARE Keep clean for best performance and to reduce the risk of injury Inspect extension cord periodicall
17. y and replace if damaged Keep handles dry clean and free from oil POLARIZED PLUGS To reduce the risk of electric shock this product has a polarized plug Polarized connections will fit together only one way Make sure that the receptacle end of the extension cord has large and small blade slot widths If the plug does not fit fully into the extension cord reverse the plug If it still does not fit obtain a suitable extension cord If the extension cord does not fit fully into the outlet contact a qualified electrician to install the proper outlet Do not change the plug on the tool or the extension cord in any way Do not operate the tiller cultivator on a slope that is too steep for safe operation When on slopes slow down and make sure you have good footing Before starting the tiller cultivator make sure the times are not touching any object and are free to move Grip the guide bar firmly with both hands Never operate the tiller cultivator with one hand CAUTION The tiller cultivator may bounce upward and or jump forward if the tines strike extremely hard packed soil frozen ground or buried obstacles such as large stones roots or stumps A A STAY ALERT Watch what you are doing Use common sense Do not operate the tiller cultivator when you are tired or under the influence of drugs or medication WARNING Do not operate the tiller cultivator near underground electrical cables telephone lines pipes or hoses
Download Pdf Manuals
Related Search