VCL-Ethernet over FE1 - Data Sheet
Contents
1. 48V DC Input The back panel of the 10 100 Base T Ethernet over E1 equipmentis as follows with DC Input Ground Positive Negative DIP switch SW1 settings on the back panel are as follows Switch 1 Switch 2 Switch 3 Switch 4 Function OFF OFF OFF OFF 10 M 100 M Auto negotiating Full Half Duplex mode OFF OFF ON OFF 10 M 3 Full Half Duplex mode OFF OFF OFF ON 100 M Full Half Duplex mode ON ON ON OFF 10M Half Duplex mode ON OFF ON OFF 10M Full Duplex mode ON ON OFF OFF 100 M Half Duplex mode ON OFF OFF OFF 100 M Full Duplex mode Orion Telecom Networks Inc 2009 10 8 VCL Ethernet over E1 FE1 DIP switch SW2 settings on the back panel are as follows Switch ON OFF Number Switch 1 Internal Clock Network Clock Switch 2 E1 External Loop back Forbidden E1 External Loop back Allowed Switch 3 Auto resetting function Forbidden Auto resetting function Allowed Switch 4 Auto resetting Delay by 16 seconds Auto resetting Delay by 8 seconds Switch 5 Manual Resetting Closed Manual Resetting Opened Switch 6 Switch 7 E1 Line Impedance 75 Q E1 Line Impedance 120 Q Switch 8 IN 75 Q Represents the E1 unbalanced 75Q input OUT 75 Represents the E1 unbalanced 75Q Output 3 Bottom Panel The bottom panel of the 10 100 Base T Ethernet over E1 equipment is as follows Working Mode 1 S15 17 S31 The occupie2. 8 NC Ethernet RJ 45 Crossover Pinouts Ethernet RJ 45 Crossover Pinouts PIN No Definition of function Signal Direction 1 TX transmitted data Data Output 2 TX transmitted data Data Output 3 RX received data Data Input 4 NC 5 NC 6 RX received data Data Input 7 NC 8 NC Orion Telecom Networks Inc 2009 10 10 VCL Ethernet over E1 FE1 General 1 Power Supply AC Mains Input Optional DC Input Power Consumption 2 Service Conditions Ambient temperature Relative humidity 3 Dimensions 4 Weight Ordering Information 220V 20 AC Mains Input Model 48V SW 0 C 50 C 90 at 35 C 20cm x 15cm x 4 3cm 750g S No Part No Product Description Qty VCL Ethernet over E1 FE1 DC 10 100 Base T Ethernet 1 electrical to 1E1 FE1 120 Ohms 75 Ohms Interface Converter with 48V DC power input VCL Ethernet over E1 FE1 AC 10 100 Base T Ethernet 1 electrical to 1E1 FE1 120 Ohms 75 Ohms Interface Converter with 220V AC power input Note Operation and maintenance of network equipment require professional knowledge and experience We recommend the equipment to be managed only by qualified technicians Should you require technical assistance please consult the provider or contact our SUPPORT DESK at support oriontelecom com Orion Telecom Networks I
3. TELECOM NETWORKS ORION TELECOM NETWORKS INC VCL Ethernet over E1 FE1 E1 10 100 Base T Interface Converter Data Sheet amp User Manual Headquarters Phoenix Arizona Orion Telecom Networks Inc 16810 Avenue of the Fountains Suite 108 Fountain Hills AZ 85268 U S A Phone 1 480 816 8672 Fax 1 480 816 0115 E mail sales oriontelecom com Website http www oriontelecom com Regional Office Miami Florida Orion Telecom Networks Inc 4000 Ponce de Leon Blvd Suite 470 Coral Gables FL33146 U S A Phone 1 305 777 0419 Fax 1 305 777 0201 E mail sales oriontelecom com Website http www oriontelecom com Orion Telecom Networks Inc 2009 10 VCL Ethernet over E1 FE1 Notice Warranty This Orion product is warranted against defects in material and workmanship for a period of one year from the date of shipment During the warranty period Orion will at its discretion either repair or replace products which prove to be defective For warranty service or repair this product must be returned to a service facility designated by Orion The buyer shall prepay shipping charges to Orion and the company shall pay shipping charges to return the product to the buyer However the buyer shall pay all the shipping charges duties and taxes for products returned to Orion from another country Limitation of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate ma
4. d Time slots at ON The occupied Time slots at ON Multiple Framed ON ra pZ g OFF Orion Telecom Networks Inc 2009 10 VCL Ethernet over E1 FE1 E1 Time Slot Setup For E1 time slot setup the DIP Switch settings on the bottom panel are as follows Working Mode Switch Setting Unframed All switches are set to OFF Framed CCS SO set to OFF and the occupied time slots to ON Multi Framed CAS All switches SO S31 set to ON but S16 is set to OFF Example 1 Ifyou wish to use only first 5 time slots then you need to set the SO time slots to OFF and switch S1 to S5 to ON and time slot S16 will be set to ON Example 2 Ifyou wish to carry first 8 time slots on 512Kbps then you need to set the SO time slot OFF and switch S1 to S8 to ON i e since each time slot consumes 64Kbps so 8 time slots will consume 8 x 64Kbps 512Kbps and time slot S16 will be set to ON Example 3 If you wish to carry 20 time slots on 1 28Mbps 64Kbps x 20 then you need to set time slot SO OFF and S1 to S21 time slots to ON Please remember that the time slot S16 will be used as signaling time slot 4 E1 RJ 45 to RJ 45 Crossover Pinout Details 1209 RJ45 pin out PIN No Definition of function Signal Direction 1 TX transmitted data E1 Data Output 2 TX transmitted data E1 Data Output 3 NC 4 RX received data E1 Data Input 5 RX received data E1 Data Input 6 NC 7 NC
5. ht through when connecting to an Ethernet switch HUB The length of the ethernet cable shall not exceed 100m Grounding When the device is used with the AC 220V power supply the 3 core socket must be grounded for protection The other equipment e g optical terminal connected with the converter shall also be grounded to earth for protection Installation Step1 Power up the Ethernet over E1 equipment Please ensure that Ethernet over E1 equipment is powered up prior to connecting the ethernet and the E1 links Step 2 Connect E1 line on the premise that transmission device interface converter and Ethernet converter have safely grounded BER test may be conducted on each E1 link using a BERT tester to ensure that the E1 errors are within the permitted limits threshold Step 3 Please configure the ethernet mode of the Ethernet over E1 equipment at both sides as well as the ethernet interfaces of the devices that are connected to the Ethernet over E1 equipment Connect the ethernet links The equipment is used to bridge two LANs Please ensure that the LANs on both sides of the link are operating in the same IP domain Step 4 Ping over the ethernet connection from one side to the other near end to the far end to verify that the Ethernet connection has been established between the two LANs After succeeding in ping the user may also check the integrity of each E1 link by connecting E1 link and then transporting e
6. intenance by the buyer the buyer supplied firmware or interfacing unauthorized modification or misuse operation outside of the environmental specifications for the product or improper site preparation or maintenance Exclusive Remedies The remedies provided herein are the buyer s sole and exclusive remedies Orion shall not be liable for any direct indirect special incidental or consequential damages whether based on contract or any legal theory Notice This manual contains information that is proprietary to Orion Telecom Networks Inc No part of this publication may be reproduced in any form whatsoever without prior written approval by Orion Telecom Networks Inc Safety Warnings The exclamation point within a triangle is intended to warn the operator or IN service personnel of operation and maintenance factors relating to the product and its operating environment which could pose a safety hazard Always observe standard safety precautions during installation operation and maintenance of this product Only qualified and authorized service personnel should carry out adjustment maintenance or repairs to this instrument No adjustment maintenance or repairs should be performed by either the operator or the user Duar ASSURANCE PROGRAM Orion s products are designed and manufactured under a strict Quality Assurance Program based on the ISO 9001 2008 philosophy and principles Orion pays very special attention to its vendor develop
7. matic Ethernet negotiation function Supports 10M 100M and working modes of both full duplex and half duplex e Available with MAC address list filtration learning and updating functions e Available with auto resetting function When network port stops receiving or sending data for about 8 seconds the auto resetting circuit will be able to start automatically to reduce and maintain workload for the system e Equipment supports two working modes of internal clock and network clock e Supports RLOOP E1 port external loop back function E1 Interface Specifications Line Rate E1 2 048 Mbps 50 bps Framing Un Framed PCM 30 PCM 31 Electrical As per ITU T G 703 Jitter As per ITU T G 823 Impedance 120 Ohm RJ 45 Impedance 75 Ohm BNC Ethernet Port specifications Interface Types 10 100BaseT Standards Compliance IEEE 802 3 Transmission Bit Rate 10 100BaseT transmission rate limited Connectors RJ 45 10 100 BaseT Electrical Clock Internal and network clock Orion Telecom Networks Inc 2009 10 5 VCL Ethernet over E1 FE1 Installation and Commissioning 3 Qualifying the network Please ensure that the error code rate each of the E1 circuits connecting to the equipment is lower than 10 The transmission time delay difference between the various E1 circuits shall not exceed 8ms The Ethernet wire type shall be crossover when connecting with PC and straig
8. ment program which ensures an end product of the highest quality at the most cost effective prices Orion Telecom Networks Inc 2009 10 2 VCL Ethernet over E1 FE1 Index INDEX Particulars General Description Typical Application Technical Feature Installation Open up and Commissioning 1 Qualifying the network 2 Grounding 3 Installation Function Description Front panel Back panel U0 OO WO NIN SODO DOAA Fi gt fe E1 Pinout Details Ethernet Pinout Details 1 2 3 Bottom Panel 4 5 General Parameters Power Supply Service conditions Dimensions Ordering Information Support CAUTION ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN OR HANDLE EXCEPT AT A STATIC FREE WORKSTATION Orion Telecom Networks Inc 2009 10 3 VCL Ethernet over E1 FE1 Description The VCL Ethernet over E1 E1 10 100 Base T Interface Converter provides the user with Ethernet over E1 conversion enabling the user to transport Ethernet data over an E1 link VCL Ethernet over E1 FE1 The equipment be always installed and used in pairs with one terminal being installed at either end of the network The VCL Ethernet over E1 E1 10 100 Base T Interface Converter is an Ethernet extension device utilizing TDM telecom infrastructure the telecom network of E1s or of PDH SDH and E1 E3 SDH microwave etc carrying E1s It c
9. nc 2009 10 VCL Ethernet over E1 FE1 Note Technical Specifications are subject to change without notice Windows is the registered Trademark of Microsoft Corporation USA Revision 08 January 16 2010 Headquarters Phoenix Arizona Orion Telecom Networks Inc 16810 Avenue of the Fountains Suite 108 Fountain Hills AZ 85268 U S A Phone 1 480 816 8672 Fax 1 480 816 0115 E mail sales oriontelecom com Website http www oriontelecom com Regional Office Miami Florida Orion Telecom Networks Inc 4000 Ponce de Leon Blvd Suite 470 Coral Gables FL 33146 U S A Phone 1 305 777 0419 Fax 1 305 777 0201 E mail sales oriontelecom com Website http www oriontelecom com Orion Telecom Networks Inc 2009 10 12
10. onverts the Ethernet data into E1 frame format for transmission over the existing TDM E1 links and then re converts the E1 back into Ethernet data the far end terminal to BRIDGE two Ethernet LANs over the existing E1 based telecom network The device can effectively utilize the redundant bandwidth of telecom operators existing TDM network to transport Ethernet data with low investment Application The equipment may be used for the following purposes Bridging Ethernet LANs over existing TDM E1 telecom network Extending Ethernet networks utilizing TDM E1 landline based telecom infrastructure e Using telecom network of E1s PDH SDH microwave etc carrying E1s to transport Ethernet data In all cases the equipment be always installed and used in pairs with one terminal being installed at either end of the network Typical Applications FE1 10 100 Base T _ FE1 10 100 Base T Interface Converter Interface Converter Application Diagram of FE1 10 100 Base T Interface Converter Orion Telecom Networks Inc 2009 10 4 VCL Ethernet over E1 FE1 Technical features The maximum transmission rate of Ethernet data over E1 links is 2 048Mbit s e E1 supports three working modes of transparent transmission framed CCS PCM 31 and multiple framed CAS PCM30 e _ Allows transparent transmission of super long frames in 1528 bytes without CRC and supports Ethernet switches with VLAN function e Auto
11. thernet data over that E1 link In the event that the Ethernet over E1 equipment resets repeatedly or lots of frame errors are noticed recheck the connection between E1 cable and interface converter or E1 cable and transmission device Orion Telecom Networks Inc 2009 10 6 VCL Ethernet over E1 FE1 Description of the Front Panel Figure of the front panel of E1 10 100 Bast T interface converter is as follows POWER LED The GREEN LED indicator lights of power supply is lit under normal working condition when the power supply is connected Definition of Indicators on front panel Switch Description PWR ON System is powered OFF System is not powere COL ON Conflict indication on LAN port OFF OK 100M ON Ethernet port rate is 100M OFF Ethernet port rate is not 100M 10M ON Ethernet port rate is 10M OFF Ethernet port rate is not 10M FDX ON Ethernet port is running in full duplex mode OFF Ethernet port is running in half duplex mode LINK ON LAN port connection Normal OFF No LAN connection on Ethernet port E1 ERR ON Solid E1 Signal lost Flushing E1 out of step OFF OK AIS ON Alarm indication of opposite terminal during transparent transmission OFF OK Orion Telecom Networks Inc 2009 10 VCL Ethernet over E1 FE1 2 A Back Panel AC Input The back panel of the 10 100 Base T Ethernet over E1 equipmentis as follows withAC Input B Back Panel
Download Pdf Manuals
Related Search