USS DDE Server
Contents
1. For example if poked F12 value is 30 1 then the VAL field in telegram will contain 301 So to poke value 30 1 into parameter P012 the following Item names with corresponding values can be used Item F12 with value 30 1 Item R12 with value 3 01 Item 112 with value 301 USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 17 Item U12 with value 301 In all these cases the same telegram will be transferred to the drive Items representing Parameter Words PnimE usually are Read Write type The server does not check whether Item value can be changed in the Converter See Converter manual before try to write new value into Converter memory Process Data Words Items The USS Server supports a list of Items that allow to control the contents of messages sent to the controlled Converter and to check the response received from Converter Item names mainly depend on Siemens USS protocol for MicroMaster 6SE21 message fields naming as well as on this protocol extension for 6RA24 converters The number of Process Data Words in message depends on Converter and protocol type and can be configured during topic configuration The default values after server start up for items representing Process Data Words and Bits of Process Data Words are zeroes 0 When the Server is restarted the Process Data Words have default values zeroes again To perform the Converter control by items representing Process Dat2. RS232 RS485 converter must be used to communicate with converter devices The RS232 to RS485 converter must ensure alternately never at the same time activation of the Receiver and the Transmitter the RTS signal is not generated by host computer and therefore if the RS232 to RS485 converter uses RTS signal at RS232 side then RTS line must be connected to host computer Transmitter line see example wiring diagram The USS DDE Server is tested with the ENTRELEC model ILPH RS232 RS422 RS485 Serial Link Interface configured as RS485 link on one pair and where the activation of the Receiver and the Transmitter is performed depending on the status of the CTRL IN signal The following wiring diagram is useful if ENTRELEC converter is used to connect PC anda slave MicroMaster The RS232 between PC and ENTRELEC RS485 between ENTRELEC and MicroMaster i NN EECHER OPC oO O ENTRELEC Soe Spin female clamp clamp hicroMaster l ERR a 3 SD M RD erp tt a3 2RD 1 _ SD D SD DE N 14 E ema oe ERD ae E zeg oy OMS Se S e v ve SANS Jumpers Rt 120 ohms R ON OFF E ON OFF USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 5 Configuring the USS Server After the USS Server is initially installed a little of configuration is required Configuring the Server automatically creates an USS CFG file that holds all of the topic defi
3. faster than rate desired to update data from the network USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 6 NetDDE being used Select this option if you are networking using NetDDE Configuration File Directory This field is used to specify the path disk drive and directory in which USS will save its current configuration file The USS Server will use this path to load the configuration file the next time it is started Note Only the path may be modified with this field The configuration file is always named USS CFG Note There is no limit to the number of configuration files created although each must be in a separate directory When using the USS Server with InTouch it is good practice to place the configuration file in the application directory Once all entries have been made click on OK USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 7 Com Port Settings Command This command is used to configure the communication port that will be used to communicate with converters Invoke the Com Port Settings command The Communication Port Settings dialog box will appear Communication Port Settings CZ Com Port COM1 Reply Timeout Secs Baud Rate Odo 2300 O600 1200 2400 4800 95600 14400 19200 38400 Data Bits Stop Bits OF En Ai CO Parity Even Odd None Mak Space The following describe
4. 1 7 150xxm17 Klinkmann Automation USS DDE Server 11 Using the USS Server with InTouch To change process data words or to access items points on converters from InTouch the following steps all performed in WindowMaker are required To define the DDE Access Names in WindowMaker for each converter invoke the Special DDE Access Names command The DDE Access Name Definition dialog box will appear DDE Access Name Definition DDE Access Names Done H Delete Click on Add The Modify DDE Access Name Dialog Box will appear Modify DDE Access Name DDE Access Name DDE Application Server Name DDE Topic Name Handling of initial data values CH Request initial data D I Wait for change When to advise server O Advise all items Advise only active items Note If Add is selected then this dialog box will be blank when it initially appears Data has been entered here to illustrate the entries that are made The following three fields are required entries when entering a DDE Access Name Definition DDE Access Name Enter an arbitrary name that will be used by InTouch to refer to the topic converter It is recommended that the name defined for the topic converter in USS also is to be used here DDE Application Server Name Enter the application name USS which the DDE Server used accessing the converter USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 12 DDE Top
5. 1 7 150xxm17 Klinkmann Automation USS DDE Server 18 Cl For Server versions from v1 0 to v1 3 the default value of STW is 3191 In Server version 1 4 and later the default value is 0 zero Notes 1 The item STW represents first Process Data Word in the send message Items STW 0 STW 15 represent bits of the first Process Data Word STW For 6RA24 the item STW is used instead of PZDO Word Each bit in STW Word has a predefined meaning which depends on Converter and protocol type 2 The item HSW is second Process Data Word in the send message and represents the frequency demand For 6RA24 the item HSW is used instead of PZD1 Word For MicroMaster the values 0 32767 represent 0 200 values 32768 65535 represent reversed 0 200 For 6SE21 the negative demand is not supported and frequency demand above 100 is clipped to 100 If only positive frequency demand values are supported then the item UHSW can be used For 6RA24 the frequency demand to the converter is scaled as follows the value 16384 represents 100 value 16384 represents 100 i e reverse therefore an Item HSW must be used 3 The item ZSW represents first Process Data Word in the response message Items ZSW 0 ZSW 15 represent bits of the first Process Data Word ZSW For 6RA24 the item ZSW is used instead of PZDO Word 4 The item HIW is the second Process Data Word in the response message and represents the output frequency of the Converter For 6RA24 the
6. DDE Server 24 POKE channel itemname Data_Reference POKEs the value contained in the Data_Reference to the specified item name actual parameter on the drive via the channel number returned by the previously executed INITIATE function Data_Reference is the row column ID of the cell containing the data value For itemname use some of the valid item names described in the Item Point Naming section TERMINATE channel Closes the channel at the end of the macro Some applications have a limited number of channels Therefore they should be closed when finished Channel is the channel number returned by the previously executed INITIATE function RETURN Marks the end of the macro The following is an example of Excel macro used to poke value from cell B2 to topic unit1 item U33i4E PokeMacro Ctrl a INITIATE USS unit1 POKE A2 U33i4E B2 ON TIME NOW 0 01 TerminateDDEChannel RETURN TerminateDDEChannel TERMINATE A2 RETURN Note Refer to the Microsoft Excel manual for complete details on entering Remote Reference formulas for cells USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 25 Troubleshooting WIN INI entries The first time you run the USS Server configuration most of the items in the following list will automatically appear in the WIN INI file It is usually in the C WINDOWS directory It is an ASCII file and can be altered manually if you wish w
7. USS DDE Server for Microsoft Windows and InTouch Applications User Manual Ver 1 x Rev 1 7 DR150 05 DR150 10 KLINKMANN AUTOMATION P O Box 38 FIN 00371 Helsinki Finland tel int 358 9 5404940 fax int 358 9 5413541 www klinkmann com Klinkmann Automation USS DDE Server i Table Of Contents USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 1 USS DDE Server The USS DDE Server hereafter referred to as the USS Server is a Microsoft Windows 32 bit application program that acts as a DDE Dynamic Data Exchange Server and allows other Windows application programs an access to data from converter devices supporting USS protocol MICRO MASTER 6SE21 6RA24 6RA22 etc The Server is primarily intended for use with Wonderware InTouch but it may be used by any Microsoft Windows program that is capable of acting as a DDE Client What is DDE DDE is a complete communication protocol designed by Microsoft to allow applications in the Windows environment to send receive data and instructions to from each other It implements a client server relationship between two concurrently running applications The server application provides the data and accepts requests from any other application interested in its data Requesting applications are called clients Some applications such as InTouch and Excel can simultaneously be both a client and a server To obtain data from another application
8. a Words or Bits of Process Data Words the corresponding Items must be activated in user application and necessary values must be assigned to them For example to allow the MicroMaster to run the user application must set an Item STW value to 3199 If any Process Data Words Item value is changed the Server sends message with changed Process Data Word value All next messages sent by the Server will contain the changed Process Data Word value until the user application changes the Process Data Word value again To recognise the right sequence for changing of Process Data Word values see your hardware manual The table below lists the Item point names representing Process Data Words and bits of these words Item name Type DDE Tag Value Range Default Type S ZE SI Word Integer TI 0 65535 o swa m Dees o oon men Word Signed Integer 16384 16384 Lt UHSW_ Word neger TI 0 65535 0 Zen Word Integer Tag 0 ZSW n Bt Discrete o oam 0 HIW Word Signed Integer 16384 16384 To UHIW Word Integer TI teen 0 n Word Deal Teens 0 PKE_CONTROL Word Integer 0 15 TI ERROR COD Word Integer 0 255 PZDSn Word Signed Integer 32768 32767 2to15 0 UPZDSn_ Word Integer 0 65535_ _ 2toi5 0 PZDRn Word Signed Integer 32768 32767 2to15 0 HEZDpn Word Integer TI 0 65535_ 2toi5s 0 USS DDE Server Ver 1 x User Manual Rev
9. aced with one of the valid topic names defined during the Server configuration process Replace item with one of the valid item point names described in the Item Point Naming or Item Point Naming for 6RA22 section Reading Values into Excel Spreadsheets Values can be read directly into Excel spreadsheets by entering a DDE formatted formula into a cell as shown in the following examples USS pIc01 U33i4E USS pc PZDR6 USS converter1 HIW The status item can be read by entering the following formula in a cell USS topic STATUS Writing Values to USS Points Values may be written to USS Server from Microsoft Excel by creating an Excel macro that uses the POKE command The proper command is entered in Excel as follows channel INITIATE USS topicname POKE channel itemname Data_Reference TERMINATE channel RETURN The following describes each of the above POKE macro statements channel INITIATE USS topicname Opens a channel to a specific topic name defined in the Server in an application with name USS the executable name less the EXE and assigns the number of that opened channel to channel Note By using the channel INITIATE statement the word channel must be used in the POKE statement instead of the actual cell reference The applicationname and topicname portions of the formula must be enclosed in quotation marks USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS
10. cation portion of the DDE address is USS Topic is an application specific sub group of data elements The USS Server considers each converter device to be a separate topic The user creates a meaningful name for each device and uses this name as the topic name for DDE references Item indicates a specific data element within the specified topic For the USS Server an item is Converter s internal Parameter or Process Data Word or Bit of Process Data Word of communication message The item point names are described in the Item Point Naming and Item Point Naming for 6RA22 section Note In some cases the term point is used interchangeably with the term item Installing the USS Server The USS DDE Server installation package can be supplied 1 Asa self extracting archive 15010xxx EXE if downloaded from Klinkmann s web site the xxx is the current latest version of the Server 2 From installation on CD 3 On two or three distribution disks floppies To install the USS DDE Server from the self extracting archive run the 15010xxx EXE and proceed as directed by the USS Server Setup program To install the USS DDE Server on Windows NT 2000 XP or 95 98 1 Insert the CD with Klinkmann Software into CD drive or insert the USS DDE Server disk into a floppy drive A or B 2 Select the Run command under the Start menu 3 Run STARTUP EXE if installing from CD or SETUP EXE if installing from distribution disks f
11. es of items PZDS2 PZDS15 are interpreted as signed Integers If values must be interpreted as unsigned integers the items UPZDS2 UPZDS15 can be used USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 19 8 The items PZDR2 PZDR15 represent Process Data Words in the response message in case of 6RA24 converters The items ZSW and HIW are used instead of PZDRO and PZDR1 The values of items PZDR2 PZDR15 are interpreted as signed Integers If values must be interpreted as unsigned integers the items UPZDR2 UPZDR15 can be used Important In USS DDE Server version 1 4 and later the default values of all Process Data Words after Server startup are zeroes 0 The Server does not perform any communication while Process Data Word STW is default zero It allows the user application to set the necessary values into all Process Data Words before sending the first request to the equipment Otherwise the Server can send to drive a command with incorrect Process Data Words and so interrupt good performance of equipment While STW is zero the Server does not create any write command it is the Server does not react to pokes of Parameter data words at all To make the Server to communicate the following should be done Poke correct values into Process Data Words except STW For example in case of MicroMaster drive firstly poke value of HSW e g 16384 poke into STW correct non zero value for examp
12. file option Doing so it will allow the USS Server to find the configuration file automatically each time it is started Configuration File Location When the USS Server starts up it first attempts to locate its configuration file by first checking the WIN INI file for a path that was previously specified If the path is not present in the WIN INI file the Server will assume that the current working directory is to be used To start the Server from an application directory configuration file other than the default configuration file a special switch d is used For example invoke the File Run command in File Manager or Program Manager and enter the following USS d c directoryname Note There is no limit to the number of configuration files that may be created although each must be in a separate directory USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 9 Topic Definition Command The user provides each connected converter with an arbitrary name that is used as the DDE topic for all references to this converter The following steps are taken to define the Topic attached to the converter 1 Invoke the Topic Definition command The Topic definition dialog box will appear Topic definition gn ooe 2 To modify an existing topic select the topic name and click on Modify To define a new topic click on New To remove an existing topic click on Delete The USS Topic Definiti
13. ging between Server and Converter as well as to control the Converter performance Parameter Items The Items representing Parameter Words are used to access the Converter internal parameters ltem point names representing Parameters generally may be described as PNn Where P prefix that identifies the type of Item The following characters can be used B b Discrete Item I i signed Integer Item U u unsigned Integer Item value 0 65535 F f Float Hem Item with value adjusted in 0 1 steps Hir Float Item Item with value adjusted in 0 01 steps N prefix that identifies the Parameter name The following characters can be used P p specifies the Parameters POO to P177 n values 0 177 correspond to parameter numbers 00 to 177 d D specifies the Parameters d00 to d30 n values 0 30 correspond to parameter numbers 200 to 230 H h specifies the Parameters H0O to H89 n values 0 89 correspond to parameter numbers 300 to 389 n specifies the Parameter number Do not use Parameter numbers unsupported on your Converter If the Server does not accept Item name without prefix that identifies the type of Item is it Discrete or Integer or other type then the error message in WWLogger file Invalid item point name appears In this case Item name should be modified so that type of Item is set in Item name by prefix Define the item type according to your hardware see Converter manual For example
14. ic Name Enter the name defined for the topic in USS to identify the converter the USS Server will be accessing Note This will usually be the same as the DDE Access Name although if desired they may be different However it must be the same name used when the topics were configured in section Configuring the USS Server Request Initial Data This option may be selected if the Server is other than a Wonderware DDE Server and the Server does not return data values immediately when a window is displayed This option is not applicable to the USS DDE Server Wait for Change This option should be selected for USS DDE Server Advise all Items This option may be selected if the Server is to poll for all data whether or not it is in visible windows alarmed logged or trended Use of the option is not recommended Advise only active Items Selecting this option will cause the USS Server to poll only points in visible windows and points that are alarmed logged or trended USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 13 Defining the Tag names To define the Tag names associated with the new DDE Access Name invoke the Special Tagname Dictionary command in WindowMaker The Dictionary Tagname Definition dialog box will appear Dictionary Tagname Definition Details Alarms C Both None 5ystem gt Read only Read Write O Log Data O Log Events O Retentive Yalue CI Rete
15. item HIW is used instead of PZD1 Word The item value is formatted in same way as for the HSW field For MicroMaster 6SE21 and other converters supporting only positive HIW values the item UHIW can be used The 6SE21 returns the current value scaled to 0 1 Amps in HIW field if the STW field bit 15 was set to 1 In this case the item FHIW must be used 5 The item PKE_CONTROL value is extracted from the response message s PKE word control bits with addresses 12 13 14 and 15 The possible values are 0 no action 1 parameter value is in the response VAL field 4 indexed parameter value transferred 7 error in the received command 8 the Converter is in Local Control parameter change request not possible 6 If the PKE_CONTROL value is 7 then the item ERROR_COD value contains the error code The possible error codes are 0 Illegal Parameter Number 1 Read Only Parameter not supported on 6SE21 2 the parameter value requested in PKW word 3 is beyond the minimum or maximum limits of acceptable values 3 the index sent in PKW word 2 is undefined 11 the request code sent in PKW word 1 is not implemented 101 the request code function sent in PKW word 1 is not implemented 102 the parameter is an indexed parameter If no errors ERROR_COD value is 255 7 The items PZDS2 PZDS15 represent Process Data Words in the send message in case of 6RA24 converters The items STW and HSW are used instead of PZDSO and PZDS1 The valu
16. ith any text editor e g MS Windows Notepad do not use a program that formats text such as MS Word or Write unless the file is saved as DOS text The following is a typical entry for the USS Server USS ProtocolTimer 50 RequestTimer 1000 ValidDataTimeout 60000 DDEBlockSize 4096 WriteRetryindefinitely 0 ConfigurationFile C USS Winlconic 0 WinFullScreen 0 WinTop 112 WinLeft 0 WinWidth 200 WinHeight 168 ShowSend 0 ShowReceive 0 ShowErrors 1 For 6RA22 device the following Items can be added to change the default values for communication telegram words E2 E3 E5 E6 E7 E8 E9 and E10 6RA22_E2 0 6RA22_E3 0 6RA22_E5 0 6RA22_E6 0 6RA22_E7 0 6RA22_E8 0 6RA22_E9 0 6RA22_E10 0 Set values you need instead of zeroes USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 26 Troubleshooting menu The following debugging choices are appended to the Server s System Menu the menu that appears when you click the box in the upper left hand corner of the Server window Suspend Protocol Resume Protocol these choices permit you to turn protocol processing on and off what allows you to suspend access to the Converter s Show Send if checked then all outgoing data is displayed in hexadecimal format Show Receive if checked then all incoming data is displayed in hexadecimal format Show Errors if checked then all information about errors is displayed Dump displays al
17. l information about opened ports active topics and data items All debug is displayed via the Wonderware Logger which must be active for these commands to work Warning if you check Show Send and or Show Receive then the debug output grows very fast USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 27 Aug 95 Jan 96 Jan 96 Oct 96 Sep 97 Jan 2001 Mar 2001 Mar 2002 Rev 1 0 Rev 1 1 Rev 1 2 Rev 1 3 Rev 1 4 Rev 1 5 Rev 1 6 Rev 1 7 KLINKMANN AUTOMATION USS DDE Server Revision History First Release Changed Default Values of Process Data Words Added Access to 6RA22 Converter Modification of manual contents Chapters Files on the USS Distribution Disks Installing the USS DDE Server Manual file name changed Minor changes Corrected Item Point naming for 6RA22 Converter Corrected Item Point naming Installation from CD information added USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17
18. l the range of values that will be accepted from the server and how the values are scaled If no scaling is desired Min EU should be equal to Min Raw and Max EU equal to Max Raw O Use Tagname as Item Name Enter the USS item point name to be associated with this tag name in the Item field in the Details box Initial Value 0 Metty Ma EU 9999 Deadband ft e Min Raw f s Max Raw 9999 Eng Units Nl Lonya on is amp Linear A Square Root ltem O Use Tagname as Item Name Log Deadband 0 7 USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 15 Refer to the Item Point Naming and Item Point Naming for 6RA22 section below for complete details Where applicable the Use Tag name as Item Name option may be selected to automatically enter the tag name in this field Note The tag name can only be used if it follows the conventions listed in the Item Point Naming and Item Point Naming for 6RA22 section Once all entries have been made click on the Save button in the top dialog box to accept the new tag name To define additional Tag names click on the New button To return to the WindowMaker main screen select Done Converter STATUS Item For each topic there is a built in discrete item that indicates the state of communication with the Converter The discrete item Status is set to 0 when communication with the Converter fails and set to 1 when communicatio
19. le value 3199 in case of MicroMaster For each Topic there is also a built in discrete item STATUS that indicates the state of communication with the Converter This discrete item is set to 0 when communication with the Converter fails and set to 1 when communication is successful The items STW STW n HSW UHSW UPZDSn and PZDSn are Write Only The items ZSW ZSW n HIW UHIW FHIW PKE_CONTROL ERROR_COD PZDRn and UPZDRn are Read Only Item Point Naming Examples The following examples show the valid item names 133 converter parameter number 33 interpreted as Integer U12E converter parameter number 12 change in RAM and EEPROM interpreted as unsigned Integer f51i2E converter parameter number 51 indexed parameter change in RAM and EEPROM index value 2 interpreted as Float i78i1 converter parameter 78 indexed parameter index value 2 interpreted as Integer PZDS3 the third PZD Control Word for 6RA24 in send message STW 4 Bit number 4 in the STW Control Word USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 20 Item Point Naming for 6RA22 This chapter deals with Item Point naming for communication with 6RA22 type converter The USS Server can access up to 390 Parameter Words from the 6RA22 Converter internal memory The Server supports additional items representing Telegram Data Words which allows user to check the contents of messages and to control the data exchan
20. loppies 4 If installing from CD select Protocol Servers DDE SuiteLink OPC find USS DDE Server and click on Setup 5 Proceed as directed by the USS Server Setup program When installation is finished the subdirectory specified as a folder where to install the USS DDE Server will contain the following files USS EXE The USS Server Program This is a Microsoft Windows 32 bit application program USS HLP The USS Server Help file USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 3 USS CFG An example configuration file LICENSE TXT Klinkmann Automation software license file WWCOMDLG DLL Dynamic Link Library necessary for USS Server To uninstall the USS Server start Control Panel select Add Remove Programs and select the USS DDE Server from the list of available software products Click on Add Remove and proceed as directed by the UnInstallShield program Note The HASP key is needed for full time running of USS Server The HASP Driver setup is performed during the Server setup Without HASP Driver installed the USS Server will run only 1 hour with all features enabled USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 4 Wiring Diagram The run time system consists of one or several converter devices slaves connected to the host computer The RS232 serial interface is used at computer side and
21. m Data Word value All next messages sent by the Server will contain the changed Telegram Data Word value until the user application changes the Telegram Data Word value again The table below lists the Item point names representing Telegram Data Words Value En Word Signed Integer _ 32768 32767 2 10 0 Uen 1 Word Unsigned Integer eso 2 10 0 Sn L Word Signed Integer _ 32768 32767 1 10 0 Usn Word Unsigned Integer eso Ip 0 Values of Speed Reference Items are limited to 16384 16384 or 0 16384 USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 22 Notes 1 The items En represent Telegram Data Words in the send message Value of En is interpreted by the Server as signed integer If values must be interpreted as unsigned integers the items UEn can be used Value of E1 is generated by the Server and is not accessible by application Value of word EA UE4 is set by the Server when operates not in a broadcast mode for read messages 0 for write messages value to be placed in the parameter identified in word E1 When in a broadcast mode this word value is set by application and contains a bit mask to allow selective operation of the control bits in word E3 All other Telegram Data Word values can be changed by an application Write only type 2 The items Sn represent Telegram Data Words in the response message Value of Sn is interp
22. message where only the control commands of word E3 are processed by the converter When value of P1023 is changed by application from 0 to 1 the Server sends a broadcast message where only the control commands of word E3 and the setpoint of word E2 are processed by the converter Telegram Data Words Items A 10 word telegram is used for communication with 6RA22 Converter The USS Server supports a list of Items that allows to control the contents of messages sent to the 6RA22 Converter and to check the response received from Converter The default values for items representing Telegram Data Words in Host to Drive telegram are zeroes 0 To change the default values add the following WIN INI file Items 6RA22_E2 6RA22_E3 6RA22_E5 6RA22 EG 6RA2Z2 E7 6RA22 E8 6RA22 EY and 6RA22 E10 with necessary default values into WIN INI file see chapter Troubleshooting The default values are set into the send messages after the Server startup To change contents of message during Server performance an application must assign correct values to E2 E3 E5 E6 E7 E8 E9 E10 Items Important Set correct values to GRA22_E2 6RA22_E3 6RA22_E5 6RA22_E6 6R 22_E7 6RA22_E8 6RA22_E9 and 6RA22_E10 in WIN INI file before Server start up Otherwise the Server can send to drive a command with incorrect Telegram Data Words and so interrupt good performance of equipment If any Telegram Data Words value is changed the Server sends message with changed Telegra
23. meter data in the message To configure topic for messages containing 3 Parameter Data Words enter value 3 in this field Default value is 3 Note Value set in this field must correspond to hardware settings For example on the 6RA24 the corresponding value is set in parameters P782 P792 For converter type 6RA22 this option is not effective in this case the Server operates with 10 word telegram Set the number of Process Data Words in the Master PC to Slave converter message and in the response Valid values in this field are from 0 to 15 Note Value set in this field must correspond to hardware settings For example on the 6RA24 parameters P781 P791 contain number of Process Data Words the control word If value of parameters P781 P791 is 3 then value 2 must be entered in the Process Data Words field Default value is 2 For converter type 6RA22 this option is not effective in this case the Server operates with 10 word telegram Note Value 3 in the Parameter Data Words field and value 2 in the Process Data Words field corresponds to simple protocol when each message contains 14 bytes Such values must be set for Siemens converters MicroMaster 6SE21 Check the 6SE21 checkbox if converter type is 6SE21 check the 6RA22 checkbox if converter type is 6RA22 In other cases do not check checkboxes When all entries have been made click on OK to process the configuration for this topic USS DDE Server Ver 1 x User Manual Rev
24. n is successful From InTouch the state of communications with the Converter may be read by defining a DDE Discrete tagname and associating it with the topic configured for the Converter and using Status as the Item name Initial Yalue Input Conversion On Msg DDE Initialized On Oor Direct O Reverse Off Msg DDE Uninitialized DDE Access Name f plc0l Item STATUS O Use Tagname as Item Hame From Excel the status of the communications may be read by entering the following formula in a cell USS topic STATUS USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 16 Item Point Naming This chapter deals with Item Point naming for communication with all types of converters except 6GRA22 The USS Server can access up to 1023 Parameter Words from the Converter internal memory The Server supports additional items representing Process Data Words and bits of these words which allows user to check the contents of messages and to control the data exchanging between Server and Converter as well as to control the Converter performance Parameter Items The Items representing Parameter Words are used to access the Converter internal parameters ltem point names representing Parameter Words generally may be described as PnimE Where P prefix which identifies the type of Item The following characters can be used D d Discrete Item I i signed Integer Item U u unsigned I
25. nitions entered as well as the communication port configurations This file will be placed automatically in the same directory in which USS EXE is located unless the path where the configuration file will be placed is specified via the Configure DDE Server Settings command To perform the required configurations start the USS program If the Server starts up as an icon then double click on the icon to open the server s window To access the commands used for various configurations open the Configure menu USS Configure Com Port Settings Topic Definition LB Server Settings DDE Server Settings Command A number of parameters that control the internal operation of the Server can be set In most cases the default settings for these parameters provide a good performance and do not require changing However they can be changed to fine tune the Server for a specific environment To change the Server s internal parameters invoke the DDE Server Settings command The DDE Server Settings dialog box will appear DDE Server Settings Protocol Timer Tick msec O HetDDE being used Configuration File Directory CAUSE The following describes each field in this dialog box Protocol Timer Tick This field is used to change the frequency at which the Server checks for work to do at this frequency one message is sent to the network and one reply from network is processed This should be approximately 2 to 4 times
26. nteger Item F f Float Item Item with value adjusted in 0 1 steps R r Float Item Item with value adjusted in 0 01 steps n specifies the Parameter number Do not use Parameter numbers unsupported on your Converter l optionally used suffix I or i indicating that Item value is accessible by Indexed parameter value request or Indexed parameter value change message m Index for Parameter Number Value m will be set in the PKW Word 2 of message Index m is used only with suffix i E optionally used suffix E or e indicating that Item value must be changed both in RAM and EEPROM If two suffixes E e and I i are used simultaneously then Indexed parameter value must be changed both in RAM and EEPROM Set the item type according to your hardware see Converter manual For example the MicroMaster parameter P015 has only two possible values 0 and 1 and item type can be Integer or Discrete Valid item names are D15 115 and U15 The MicroMaster parameter P016 has three possible values In this case item type must be Integer and valid item names are 116 and U16 The MicroMaster parameter P012 values may be set between 0 0 and 650 0 Hertz i e parameter value is adjusted in 0 1 steps In this case the data format is scaled to 0 1 and item name F12 is useful If poke F12 then the Server takes the Float value of F12 converts it to 16 bit Short Integer scaled in 0 1 steps and puts it into VAL field of send telegram
27. ntive Parameters Click on New and enter the Tag Name The tag name defined here is the name InTouch will use The USS Server does not see this name Select the tag type by clicking on the Type button The Choose tag type dialog box will appear Choose tag type Mee ao E In order to access USS items the type must be DDE Discrete DDE Integer or DDE Real Select the DDE type The Details dialog box for the tag name will appear Initial Value 0 Min EU o Ma EU 9999 Deadband fs Min Raw f s Max Raw 9999 Eng Units oo at aa i amp Linear i Unassigned CH Square Foot O Use Tagname as Item Name Log Deadband fs Select the USS topic converter by clicking on the DDE Access Name button The DDE Access Name Definition dialog box will appear USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 14 DDE Access Name Definition DDE Access Names Select the appropriate topic name and click on Done If the DDE Access Name has not been defined as previously described click on Add and define the DDE topic now The Details dialog box will appear displaying the selected DDE Access Name Initial Value 0 Metty Ma EU 9999 Deadband oo Z o e Hin Raw DN Man Raw 9999 SE Conversion Eng Units SRA Linear CH Square Foot Log Deadband 0 For integers and reals fill in the Min EU Max EU Min Raw and Max Raw fields These fields contro
28. on dialog box will appear USS Topic Definition Station number Com Port COM1 Max paints Update Interval Parameter Data Vfords Process Data Words 6SE21 LJ 3 Enter the Topic Name that corresponds to the DDE Topic Name The DDE Topic Name is entered in the DDE Access Name Definition dialog box described in the Using the USS Server with InTouch section USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 10 10 11 Enter the Station number for this converter device Note Each converter must have a unique address from 0 to 30 Station number 255 can be used as a broadcast address If some data is sent to this address then all connected converters will receive these data It is impossible to read data from topic with Station number 255 Click on the Com Port button to associate a topic with the communication port Note Additional topics may be associated with the same communication port later Set the Max supported points for topic converter Set the number of really used polled items points or little higher not maximum allowed Default value is 128 Set the Update Interval field to indicate the frequency the items points on this topic will be read polled Default value is 1000 milliseconds Set the number of Parameter Data Words in the Master PC to Slave converter message and in the response Value less than 3 in this field means that there is no para
29. reted by the Server as signed integer If values must be interpreted as unsigned integers the items USn can be used All Item S1 510 values are accessible by application but can not be changed by application Read only type Parameter value S4 is extracted by the Server and given to application as correspondent parameter Pn value For each Topic there is also a built in discrete item STATUS that indicates the state of communication with the Converter This discrete item is set to 0 when communication with the Converter fails and set to 1 when communication is successful Item Point Naming Examples The following examples show the valid item names id9 converter parameter number 209 interpreted as signed Integer Ud10 converter parameter number 210 interpreted as unsigned Integer E3 Telegram Data Word number 3 in send message interpreted as signed Integer 10 Telegram Data Word number 10 in response message interpreted as signed Integer US3 Telegram Data Word number 3 in response message interpreted as unsigned Integer USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 23 Notes on Using Microsoft Excel Data from topics may be accessed from Excel spreadsheets To do so enter a formula like the following into a cell on the spreadsheet USS topictitem Sometimes Excel requires the topic and or item points to be surrounded by apostrophes In the formula topic must be repl
30. s each field in this dialog box Com Port Select the Com Port and examine the characteristics of the selected Port To select a necessary Com Port click on the combo box button and make your choice from the list box Reply Timeout This field is used to enter the amount of time in seconds all converters using the selected communication port will be given to reply to commands from the Server Note The default value of 3 seconds should be sufficient for most configurations Baud Rate The selected Baud Rate must match the converter setting Note The default Baud Rate is 9600 Other communication parameters are following 8 Data Bits 1 Stop Bit Even Parity These parameters cannot be changed When all entries have been made click on Done to process the configuration for the communication port USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 8 Saving USS Configuration File If the configuration file does not currently exist or a new configuration path has been specified the Server will display the Save Configuration dialog box save Configuration Configuration File Directory C AUSS E Hake this the default configuration file This dialog box displays the path where the Server is going to save the current configuration file The path may be changed if necessary Also the path can optionally be recorded in the WIN INI file by selecting the Make this the default configuration
31. the client program opens a channel to the server application by specifying three things the server application name the topic name and the specific item name For example in the case of Excel the application name is Excel the topic name is the name of the specific spreadsheet that contains the data and the item name is the specific cell on the spreadsheet With InTouch the application name is View the topic name is the word Tagname when reading writing to an InTouch tag name and the item name is a specific tag name in the InTouch Data Dictionary When a client application sets up a link to another DDE program it requests the server application to advise the client whenever a specific item s value changes These data links will remain active until either the client or server program terminates the link or the conversation They are a very efficient means of exchanging data because when the link has been established no communication occurs until the specified data value changes InTouch uses DDE to communicate with DDE Servers and other DDE application programs USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 2 Accessing a Remote DDE Item from USS The DDE protocol identifies an element of data by using a three part address including Application Topic and Item Application refers to the name of the Windows program server that knows how to access the data element For the USS Server the appli
32. the parameter described in Converter manual as E73 has possible values 0 15 and item type can be integer or unsigned integer Valid item names are IP173 and UP173 Float items are useful if parameter value is adjusted in 0 1 or 0 01 steps In this case item names with prefix F f or R r are useful If poke some value into such Float item then the Server takes the Float value converts it to 16 bit Short Integer scaled in 0 1 or 0 01 steps and puts it into value field of send telegram For example if poked value of item with prefix F f is 30 1 then the value field in telegram will contain 301 So to poke value 30 1 the following Item names with corresponding values can be used Item name with prefix F f with value 30 1 Item name with prefix R r with value 3 01 Item name with prefix I i with value 301 Item name with prefix U u with value 301 In all these cases the same telegram will be transferred to the drive USS DDE Server Ver 1 x User Manual Rev 1 7 150xxm17 Klinkmann Automation USS DDE Server 21 Items representing Parameter Words Pn usually are Read Write type The server does not check whether Item value can be changed in the Converter See Converter manual before try to write new value into Converter memory Additional DDE Discrete Items P1022 and P1023 are supported by the USS DDE Server in broadcast mode for Topic number 255 When value of P1022 is changed by application from 0 to 1 the Server sends a broadcast
Download Pdf Manuals
Related Search