RIDGID R2611 User's Manual
Contents
1. Precautions that involve your safety Failure to keep your hands away from the blade will result in seri ous personal injury Failure to keep your hands away from the blade will result in serious personal injury Failure to keep your hands away from the blade will result in serious personal injury Failure to keep your hands away from the blade will result in serious personal injury To reduce the risk of injury or damage avoid contact with any hot surface SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product SYMBOL SIGNAL MEANING DANGER Indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION Indicates a potentially hazardous situation which if not avoided may i result in minor or moderate injury CAUTION SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair When servic ing use only identical replacement parts A WARNING Without Safety Alert Symbol Indicates a situation that may result in property damage A WARNING To avoid serious personal injury do not attempt to use this produ2. Model No R2611 Serial No
3. live wire will make exposed metal parts of the tool live and shock the operator Know your power tool Read operator s manual care fully Learn its applications and limitations as well as the specific potential hazards related to this tool Following this rule will reduce the risk of electric shock fire or serious injury Always wear safety glasses Everyday eyeglasses have only impact resistant lenses they are NOT safety glasses Following this rule will reduce the risk of serious personal injury Protect your lungs Wear a face or dust mask if the operation is dusty Following this rule will reduce the risk of serious personal injury Protect your hearing Wear hearing protection during extended periods of operation Following this rule will reduce the risk of serious personal injury Inspect tool cords periodically and if damaged have repaired at your nearest authorized service center Constantly stay aware of cord location Following this rule will reduce the risk of electric shock or fire Check damaged parts Before further use of the tool a guard or other part that is damaged should A WARNING E When servicing a power tool use only identical replace ment parts Follow instructions in the Maintenance sec tion of this manual Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of shock or injury be carefully checked to determine that it will operate properly and
4. products may vary HOW TO OBTAIN SERVICE To obtain service for this RIDGID tool you must return it freight prepaid or take it in to an authorized service center for RIDGID branded hand held and stationary power tools You may obtain the location of the authorized service center nearest you by calling toll free 1 866 539 1710 or by log ging on to the RIDGID website at www ridgid com When requesting warranty service you must present the original dated sales receipt The authorized service center will re pair any faulty workmanship and either repair or replace any part covered under the warranty at our option at no charge to you 15 WHAT IS NOT COVERED This warranty applies only to the original purchaser at retail and may not be transferred This warranty only covers de fects arising under normal usage and does not cover any malfunction failure or defect resulting from misuse abuse neglect alteration modification or repair by other than an authorized service center for RIDGID branded hand held and stationary power tools Consumable accessories pro vided with the tool such as but not limited to blades bits and sand paper are not covered RIDGID INC AND ONE WORLD TECHNOLOGIES INC MAKE NO WARRANTIES REPRESENTATIONS OR PROMISES AS TO THE QUALITY OR PERFORMANCE OF ITS POWER TOOLS OTHER THAN THOSE SPECIFI CALLY STATED IN THIS WARRANTY ADDITIONAL LIMITATIONS To the extent permitted by applicable law all i
5. left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations Dress properly Do not wear loose clothing or jewelry Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of these devices can reduce dust related hazards Do not wear loose clothing or jewelry Contain long hair Loose clothes jewelry or long hair can be drawn into air vents Do not use on a ladder or unstable support Stable footing on a solid surface enables better control of the power tool in unexpected situations POWER TOOL USE AND CARE Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source and or the battery pack from the power tool before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool ac
6. perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and any other conditions that may affect its operation A guard or other part that is damaged should be properly repaired or replaced by an authorized service center Following this rule will reduce the risk of shock fire or serious injury Make sure your extension cord is in good condition When using an extension cord be sure to use one heavy enough to carry the current your product will draw A wire gauge size A W G of at least 16 is recommended for an extension cord 50 feet or less in length A cord exceeding 100 feet is not recom mended If in doubt use the next heavier gauge The smaller the gauge number the heavier the cord An undersized cord will cause a drop in line voltage resulting in loss of power and overheating Inspect for and remove all nails from lumber before using this tool Following this rule will reduce the risk of serious personal injury Save these instructions Refer to them frequently and use them to instruct others who may use this tool If you loan someone this tool loan them these instructions also Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to cause cancer birth defects or other reproductive harm Some examples of these chemicals are e lead from lead based paints crystalline silica from bricks a
7. possible serious injury WARNING Do not use any attachments or accessories not recommended by the manufacturer of this tool The use of attachments or accessories not recommended can result in serious personal injury APPLICATIONS You may use this tool for the purposes listed below E Sanding wood or wood product surfaces E Sanding steel surfaces E Removing rust from steel surfaces ATTACHING THE FRONT HANDLE See Figure 2 E Unplug the sander E Place handle in the desired position E Tighten the handle by inserting the hex key into the handle hole engaging the hex screw inside and turning clockwise 10 la BEG TY BLOG SS MZF a HANDLE HEX KEY SANDING DISC SELECTION Selecting the correct size grit and type sanding disc is an extremely important step in achieving a high quality sanded finish Aluminum oxide silicon carbide and other synthetic abrasives are best for power sanding Natural abrasives such as flint and garnet are too soft for economical use in power sanding In general coarse grit will remove the most material and finer grit will produce the best finish in all sanding operations The condition of the surface to be sanded will determine which grit will do the job If the surface is rough start with a coarse grit and sand until the surface is uniform Medium grit may then be used to remove scratches left by the coarser grit and finer grit used for finishing of the surface Always
8. G ON THE SANDER See Figure 8 The sander is equipped with a lock on feature which is convenient for continuous sanding for extended periods of time A WARNING Before connecting the sander to a power supply make sure it is not in the locked on position Failure to do so could result in accidental starting of the tool resulting in serious injury To lock on the sander E Depress the switch trigger E Push in the lock on button E Release the switch trigger E Release the lock on button NOTE To release the lock depress the switch trigger 12 DUST BAG id 2 1 2 in VACUUM HOSE SWITCH TRIGGER Fig 8 If you have the lock on feature engaged during use and the sander is accidentally disconnected from the power supply disengage the lock on feature immediately Also do not lock the switch trigger if you might need to suddenly stop the sander OPERATION OPERATING THE SANDER See Figure 9 To operate the sander E Secure the workpiece to prevent it from moving during operation A WARNING Unsecured workpieces could be thrown towards the operator causing injury A WARNING Keep your head away from the sander and the sanding area Your hair could be drawn into the sander causing serious injury E Place the sander on the workpiece so that all of the sand ing disc surface is in contact with the workpiece CAUTION To avoid motor damage resulting from overheating do not cover
9. OPERATOR S MANUAL RANDOM ORBIT SANDER DOUBLE INSULATED VARIABLE SPEED R2611 RIDGID Your sander has been engineered and manufactured to our high standards for dependability ease of operation and operator safety When properly cared for it will give you years of rugged trouble free performance A WARNING To reduce the risk of injury the user must read and understand the operator s manual before using this product Thank you for buying a RIDGID product SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS WTPOGUCTI OM s siie aaa avec aad rend ERE aaa eaa N Ea AAE Ra NE LET a yee a aaia EEE bord Eaa 2 cenoral Saloy RULOS ipare i a EEE NERE A OBETUA AE AA NT TAE E EEEE AEA 3 4 Sece onee e RUSS E A E T E E E A E E A E A T 4 SDV ITIOOIS ei a E E S R 5 6 ea E E E E A enc didei bans douse ate nefeunaipesteadsueced sents eens awieas 7 Features rere os aa a a eran caceutenasa cs aacusecscohex cua peetaxaancaaadetmacenasarnet sensu ese cones nseenctaseshassco nenetsecassuueagetivevenuncchsates 8 9 ASSOMM DIY secuttt secant titateseneediteesvnt S sha etaaesecaevaaet recat dart hides atvelad i vieviaeeGrcbeiiessenees 9 OPS ALI OM te ws cava es de et i ae E E Sah ven SORA dace dag wate dab bate dale ves sua ne ce Sete eee eden neva A Were ts 10 13 WET niti8 fe la o gt a enenenerr eer err e a E tecrrrerreremrrercestrrtrrrer rere reer reese ter emer errr rere A error 14 WV ANU E ccc cea cedecesadascutctesasteceeassseaccsnsd
10. Y RIDGID HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY Proof of purchase must be presented when requesting war ranty service Limited to RIDGID hand held and stationary power tools purchased 2 1 04 and after This product is manufactured by One World Technologies Inc The trademark is licensed from RIDGID Inc All warranty communications should be directed to One World Technologies Inc attn RIDGID Hand Held and Stationary Power Tool Technical Service at toll free 1 866 539 1710 90 DAY SATISFACTION GUARANTEE POLICY During the first 90 days after the date of purchase if you are dissatisfied with the performance of this RIDGID Hand Held and Stationary Power Tool for any reason you may return the tool to the dealer from which it was purchased for a full refund or exchange To receive a replacement tool you must present proof of purchase and return all original equipment packaged with the original product The replacement tool will be covered by the limited warranty for the balance of the 3 YEAR service warranty period WHAT IS COVERED UNDER THE 3 YEAR LIMITED SERVICE WARRANTY This warranty on RIDGID Hand Held and Stationary Power Tools covers all defects in workmanship or materials and nor mal wear items such as brushes chucks motors switches cords gears and even cordless batteries in this RIDGID tool for three years following the purchase date of the tool Warranties for other RIDGID
11. and any accessories from the box Make sure that all items listed in the packing list are included E Inspect the tool carefully to make sure no breakage or damage occurred during shipping E Do not discard the packing material until you have care fully inspected and satisfactorily operated the tool E If any parts are damaged or missing please call 1 866 539 1710 for assistance PACKING LIST Random Orbit Sander Sanding Disc 80 grit 3 Handle Assembly Dust Bag Assembly Hex Key Operator s Manual A WARNING If any parts are damaged or missing do not operate this tool until the parts are replaced Failure to heed this warning could result in serious personal injury WARNING Do not attempt to modify this tool or create accessories not recommended for use with this tool Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury AY WARNING Do not connect to power supply until assembly is complete Failure to comply could result in accidental starting and possible serious personal injury OPERATION A WARNING Do not allow familiarity with tools to make you careless Remember that a careless fraction of a second is sufficient to inflict severe injury A WARNING Always wear safety goggles or safety glasses with side shields when operating tools Failure to do so could result in objects being thrown into your eyes resulting in
12. center for repair Always use original factory replace ment parts when servicing ELECTRICAL CONNECTION This tool has a precision built electric motor It should be connected to a power supply that is 120 volts 60 Hz AC only normal household current Do not operate this tool on direct current DC A substantial voltage drop will cause a loss of power and the motor will overheat If your tool does not operate when plugged into an outlet double check the power supply EXTENSION CORDS When using a power tool at a considerable distance from a power source be sure to use an extension cord that has the capacity to handle the current the tool will draw An undersized cord will cause a drop in line voltage resulting in overheating and loss of power Use the chart to determine the minimum wire size required in an extension cord Only round jacketed cords listed by Underwriter s Laboratories UL should be used When working outdoors with a tool use an extension cord that is designed for outside use This type of cord is designated with WA on the cord s jacket Before using any extension cord inspect it for loose or exposed wires and cut or worn insulation Ampere rating on tool data plate 0 2 0 2 1 3 4 3 5 5 0 5 1 7 0 Cord Length Wire Size A W G 25 16 16 16 16 14 14 50 16 16 16 14 14 12 o e e a 2 w Used on 12 gauge 20 amp circuit NOTE AWG American Wire Gauge 7 1 12 0 12 1 16 0 A WARNING K
13. cidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or bind ing of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools Keep cutting tools sharp and clean Properly main tained cutting tools with sharp cutting edges are less likely to bind and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into account the working conditions and the work to be performed Use of the power tool for operations dif ferent from those intended could result in a hazardous situation GENERAL SAFETY RULES SERVICE E Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained A WARNING To reduce the risk of injury user must read instruction manual SPECIFIC SAFETY RULES E Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord Contact with a
14. continue sanding with each grit until surface is uniform OPERATION ATTACHING HOOK AND LOOP SANDING DISC See Figure 3 To attach hook and loop sanding disc E Unplug the sander E Align the holes in the sanding disc with the holes in the hook and loop backing pad Press the sanding disc against the backing pad as firmly as possible NOTE To provide for the best adhesion we recom mend that you clean the backing pad and the sanding disc backing occasionally by brushing them lightly with a small brush SELECTING THE ORBIT DIAMETER See Figure 4 The dual random orbit selector allows you to choose between two orbits the 1 8 in orbit setting produces a finer surface finish while the 1 4 in orbit setting increases the removal rate With the sander held in normal operating position the dual random orbit selector should be positioned to the left of the switch trigger for a 1 4 in orbit diameter The dual random orbit selector should be positioned to the right of the switch trigger for a 1 8 in orbit diameter VARIABLE SPEED DIAL See Figure 5 The variable speed dial allows the sander to operate at speeds that can be adjusted by rotating the dial from A to F The dial is conveniently located on the motor housing allow ing operator control of disc speed To increase sanding disc speed turn the variable speed dial to a higher setting Turn dial to a lower setting to decrease sanding disc speed Recommended speed se
15. ct until you read thoroughly and understand completely the operators manual Save this operator s manual and review frequently for continuing safe operation and instructing others who may use this product The operation of any power tool can result in foreign objects being thrown into your eyes which can result in severe eye damage Before beginning power tool operation always wear safety goggles safety glasses with side shields or a full face shield when needed We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields Always use eye protection which is marked to comply with ANSI 287 1 SAVE THESE INSTRUCTIONS ELECTRICAL DOUBLE INSULATION Double insulation is a concept in safety in electric power tools which eliminates the need for the usual three wire grounded power cord All exposed metal parts are isolated from the internal metal motor components with protect ing insulation Double insulated tools do not need to be grounded AY WARNING The double insulated system is intended to protect the user from shock resulting from a break in the tool s internal wiring Observe all normal safety precautions to avoid electrical shock NOTE Servicing of a tool with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician For service we suggest you return the tool to your nearest authorized service
16. eep the extension cord clear of the working area Position the cord so that it will not get caught on lumber tools or other obstructions while you are working with a power tool Failure to do so can result in serious personal injury A WARNING Check extension cords before each use If damaged replace immediately Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury FEATURES PRODUCT SPECIFICATIONS Sanding Disc Diameter cccesseeeeeeeeseeceeeeessenees 6 in ADUT ereina 120 V 60 Hz AC only 4 Amps Orbit DiaAMSter sisisi siirinsesi 1 8 in or 1 4 in INGEVV iG Int criscini ar E 6 3 Ibs NO Load SPee ipisna 4 000 10 000 min VACUUM ADAPTOR LOCK ON BUTTON DUAL RANDOM ORBIT SELECTOR VARIABLE SPEED DIAL FRONT K up HANDLE SWITCH TRIGGER BACKING PAD LIGHTED PLUG Fig 1 FEATURES KNOW YOUR RANDOM ORBIT SANDER See Figure 1 Before attempting to use this product familiarize yourself with all operating features and safety rules ADJUSTABLE FRONT HANDLE For ease of operation the front handle can be adjusted using the supplied hex key BACKING PAD The hook and loop backing pad allows you to quickly and easily attach sanding discs CORD WRAP The 12 foot power cord has a built in cord wrap DUAL RANDOM ORBIT SELECTOR The random orbit motion provides overlapping sanding movements by combining orbital and
17. faces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded E Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of elec tric shock E Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock E When operating a power tool outdoors use an exten sion cord suitable for outdoor use Use of a cord suit able for outdoor use reduces the risk of electric shock PERSONAL SAFETY E Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury E Use safety equipment Always wear eye protection Safety equipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropri ate conditions will reduce personal injuries E Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents Remove any adjusting key or wrench before turning the power tool on A wrench or a key
18. mplied war ranties including warranties of MERCHANTABILITY or FIT NESS FOR A PARTICULAR PURPOSE are disclaimed Any implied warranties including warranties of merchantability or fitness for a particular purpose that cannot be disclaimed under state law are limited to three years from the date of purchase One World Technologies Inc and RIDGID Inc are not responsible for direct indirect incidental or conse quential damages Some states do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential dam ages so the above limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state One World Technologies Inc P O Box 35 Hwy 8 Pickens SC 29671 983000 861 3 24 06 REV 02 OPERATOR S MANUAL RANDOM ORBIT SANDER DOUBLE INSULATED VARIABLE SPEED R2611 Customer Service Information For parts or service contact your nearest RIDGID authorized service center Be sure to provide all relevant information when you call or visit For the location of the authorized service center nearest you please call 1 866 539 1710 or visit us online at www ridgid com The model number of this tool is found on a plate attached to the motor housing Please record the serial number in the space provided below When ordering repair parts always give the following information
19. nd cement and other masonry products and e arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles SYMBOLS Some of the following symbols may be used on this tool Please study them and learn their meaning Proper interpreta tion of these symbols will allow you to operate the tool better and safer SYMBOL NAME Volts Amperes Hertz Watt Minutes Alternating Current Direct Current No Load Speed Class Il Construction Per Minute Wet Conditions Alert Read The Operator s Manual Eye Protection Safety Alert No Hands Symbol No Hands Symbol No Hands Symbol No Hands Symbol Hot Surface DESIGNATION EXPLANATION Voltage Current Frequency cycles per second Power Time Type of current Type or a characteristic of current Rotational speed at no load Double insulated construction Revolutions strokes surface speed orbits etc per minute Do not expose to rain or use in damp locations To reduce the risk of injury user must read and understand operator s manual before using this product Always wear safety goggles safety glasses with side shields or a full face shield when operating this product
20. ng surface coatings such as polyurethanes linseed oil etc can self ignite in the sander dust bag or elsewhere and cause fire To reduce the risk of fire always empty the dust bag frequently while sanding and never store or leave a sander without totally emptying its dust bag Also follow the recommendations of the coatings manufacturers To empty the dust bag E Unplug the sander E Remove the dust bag from the sander E Shake out the dust E Reattach the dust bag to the sander For a more thorough cleaning of the dust bag remove dust bag from frame and shake out dust Replace dust bag over frame then install dust bag assembly on sander MAINTENANCE A WARNING When servicing use only identical RIDGID replacement parts Use of any other parts may create a hazard or cause product damage WARNING Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust If operation is dusty also wear a dust mask GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use Use clean cloths to remove dirt dust oil grease etc A WARNING Do not at any time let brake fluids gasoline petroleum based products penetrating oils etc come in contact with plastic parts Chemicals can damage weaken or destroy plastic which may result in serious pers
21. onal injury Electric tools used on fiberglass material wallboard spack ling compounds or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings brushes com mutators etc Consequently we do not recommended using this tool for extended work on these types of materials How ever if you do work with any of these materials it is extremely important to clean the tool using compressed air LUBRICATION All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions Therefore no further lubrication is required 14 BRUSH REPLACEMENT See Figure 11 E Unplug the sander A WARNING Failure to unplug the tool could result in accidental starting causing possible serious injury Remove screws 7 from top cover of sander Remove top cover Disconnect lead terminals from brush tubes Remove brush assemblies 2 Check for wear Replace both brush assemblies when either has less than 1 4 in length of carbon remaining Do not replace one side without replacing the other E Reassemble using new brush assemblies Make sure curvature of brush matches curvature of motor and that brush moves freely in brush tube E Reassemble by reversing the steps listed above E Tighten all screws securely Do not over tighten WARRANT
22. situsssaant tect saceacuctetses2euceena cute E E 2eetsazegaade E 15 CUSTOMEF Service INFOMATION 12 i sssszee ofevnecveneus copes ceded tenn r aa added dew saws Paaa ead d PEV anadan aaar AERE S AERE a te 16 INTRODUCTION This tool has many features for making its use more pleasant and enjoyable Safety performance and dependability have been given top priority in the design of this product making it easy to maintain and operate GENERAL SAFETY RULES A WARNING Read all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious injury The term power tool in all of the warnings listed below refers to your mains operated corded power tool or battery operated cordless power tool SAVE THESE INSTRUCTIONS WORK AREA SAFETY E Keep work area clean and well lit Cluttered or dark areas invite accidents E Do not operate power tools in explosive atmo spheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes E Keep children and bystanders away while operating a power tool Distractions can cause you to lose control ELECTRICAL SAFETY E Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock E Avoid body contact with earthed or grounded sur
23. the air vents with your hand E Turn onthe sander and move it slowly over the workpiece Make successive passes in parallel lines circles or cross wise movements E Turn off the sander and wait until the sanding disc comes to a complete stop before removing it from the workpiece Do not force The weight of the unit supplies adequate pressure to do the work Applying additional pressure only slows the motor rapidly wears the sanding sheet and greatly reduces sander speed Excessive pressure will overload the motor causing possible damage from overheating and can result in inferior work Any finish or resin on wood may soften from the frictional heat Do not sand on one spot too long as the sander s rapid action may remove too much material making the surface uneven Extended periods of sanding may overheat the motor If this occurs turn the sander off and wait until the sanding sheet comes to a complete stop Remove sander from workpiece Remove sanding disc then turn sander on and run it free without a load to cool the motor EMPTYING THE DUST BAG See Figure 10 For more efficient operation empty the dust bag when itis no more than half full This will permit the air to flow through the bag better Always empty and clean the dust bag thoroughly upon completion of a sanding operation and before placing the sander in storage 13 DUST BAG Fig 10 A WARNING Collected sanding dust from sandi
24. ttings are as follows Speed Surface Application A B plastic plexiglass C D metal finishing old paint removal E F wood coarse and fine sanding 11 SANDING DISC HOOK AND LOOP BACKING PAD 1 4 DUAL RANDOM ORBIT SELECTOR Fig 4 TO INCREASE SPEED TO DECREASE SPEED OPERATION ATTACHING THE DUST BAG See Figure 6 The dust bag provides a dust collection system for the sander Sanding dust is drawn up through the holes of the sanding disc and collected in the dust bag during sanding To attach the dust bag E Unplug the sander E Slide dust bag assembly onto blower exhaust turning clockwise to tighten ATTACHING THE SANDER TO A VACUUM See Figure 7 To attach the sander to a vacuum E Unplug the sander E Turn the dust bag counterclockwise to remove from sander E Attach the vacuum hose to the vacuum adaptor A WARNING When sander is not connected to vacuum always install dust bag back on sander Failure to do so could cause sanding dust or foreign objects to be thrown into the face or eyes which could result in possible serious injury NOTE A standard 1 1 4 in vacuum hose fits inside the smaller diameter hole inside the dust exhaust while a stan dard 2 1 2 in vacuum hose connection fits inside the larger hole of the dust exhaust TURNING THE SANDER ON OFF See Figure 8 Depress the switch trigger to turn the sander ON Release the switch trigger to turn the sander OFF LOCKIN
25. turning motion These overlapping sanding movements provide fast cutting action with excellent sanding results DUST BAG The dust bag attaches to the sander and keeps dust to a minimum ERGONOMIC DESIGN Your random orbit sander is designed for comfort and ease of operation in different positions and at different angles ASSEMBLY INTEGRATED BRAKE PAD The integrated brake pad prevents pad overspin This feature helps eliminate sanding scratches when you apply the sander to or remove it from a work surface LIGHTED PLUG The lighted plug helps to easily identify live tools LOCK ON BUTTON The lock on feature allows you to lock the switch trigger in the ON position Locking the switch trigger on allows you to operate the sander for extended periods of time SOFT START When a speed is selected with the variable speed dial and the sander is stopped and then reactivated the sander will gradually ramp up to the previous speed setting once the switch trigger is pressed again VACUUM ADAPTOR The vacuum adaptor allows you to connect to a 1 1 4 in or 2 1 2 in diameter vacuum hose to help keep the work area clean VARIABLE SPEED DIAL The variable speed feature allows the sander to develop a no load speed that can be adjusted from 4 000 to 10 000 orbits per minute by rotating the dial from A slowest to F fastest UNPACKING This product has been shipped completely assembled E Carefully remove the tool
Download Pdf Manuals
Related Search