Aurora Reusable Cartridge Handling Manual
Contents
1. plus or minus symbol appears on the display to indicate that thermal control is operating If a star appears press Start again Begin the run From the home screen of the Aurora software load and run the protocol appropriate for your application ex 106 0001 CA D AURORA DNA CLEAN UP PROTOCOL as described in the Operating the Aurora section of the Aurora User Manual Create an experiment folder for the run to save the logs The run will typically complete in 2 4 hours depending on the protocol that you are running Sample extraction After a run is complete Pull gently outward at both left and right sides of the cartridge drawer until the drawer slides out and latches in the open position e Lift the cartridge from the platform taking care not to spill any liquid and place the cartridge on a flat work surface 17 Examine the concentration gel and ensure that there are no large bubbles present Presence of large bubbles indicates that the gel overheated during the run which will adversely affect the quality of the output e Using forceps or gloved fingers remove the clear film covering the extraction well in the center of the gel e Transfer concentrated DNA from this well using a pipette taking care not to disturb the concentration gel e Typically two pipetting steps are required in order to extract most of the liquid from the extraction well Be sure to extract any sample that is suspended on the walls of t2. the gel and the post and then gently pull it straight out of the cartridge Do not cover the hollow center region of the post with your finger when removing it as this will create a small vacuum and could damage the gel e Inspect the well formed by the post the walls should be straight and clean and the center of the well should be free of any gel If there are any gel fragments in this well use forceps or a bent wire to remove it taking care to avoid damage to the sides of the well Filling buffer chambers Materials required same buffer that was used to make the gel e Serological pipette 5 10 or 20 ml Procedure a workbench prepare the cartridge for running Add5mlof buffer to each of the buffer chambers D and and then add 4 ml of buffer to buffer chamber F see Figure 1 e Place the electrode plate on top of the cartridge so that the 2 plastic alignment pins fit inside the respective hole and slot The graphite electrodes should not mechanically interfere with the floor of the cartridge however it is acceptable if they come very close to the floor e Add 60 ul of buffer to the extraction well Cuta piece of PCR tape into a rectangle sized 28 mm x 10 mm Boreal Genomics recommends MicroAmp Optical Adhesive Film available LIFE Invitrogen 4311971 e Remove the white backing from the piece of PCR tape and place it on top of the extraction well as shown in Figure 6 One edge of the film
3. 5 BOREAL GENOMICS Aurora Reusable Cartridge Handling Manual 2015 Boreal Genomics Inc All rights reserved All trademarks are property of their owners http www borealgenomics com support borealgenomics com 1 604 822 4111 Table of Contents ESR ONS SG 4 AC 4 SALE AV ard g PEE AE E NI 4 PECK 5 7 Preparing nas cla aed O 7 8 Preparing thesample 9 Preparing he Cartier 9 Castine 6 12 DUTTON AE 14 17 Prepare the Ay Ui Olea 17 BEGIN CMC WU 17 Sampie extracto 17 Cleaning cartridges ACCESS ONS 2 R 18 Replacing graphite ClECLVOO CS 20 D
4. ISPOSA 20 POUDI 20 orderne and SUD DONE 25500 1660 caus 22 Experienced 23 Introduction This manual describes the proper method of preparing a reusable cartridge for use with the Aurora loading the sample in the cartridge extracting the purified DNA from the cartridge once the Aurora purification is complete and cleaning the cartridge Details on preparing a variety of sample types prior to loading them into the Aurora cartridge can be found in separate Aurora protocol documents on the Boreal Genomics website http www borealgenomics com customer service Cartridge compatibility The procedures described in this manual apply to Aurora Reusable Cartridge 211 0004 AA D Safety guidelines Cartridges are made from non hazardous plastics graphite electrodes and aluminum Appropriate precautions should be taken if hazardous samples are used with the cartridges Wear gloves during all stages of the protocol Avoid skin contact with all reagents Refer to safety guidelines in Boreal Genomics Protocol documents for further information Pack list One reusable cartridge kit contains the following items and quantities Reusable electrode plate top With 6 graphite electrodes pre inserted Wit
5. Next cast the sample gel between Type C and D dams Let the gel set for 20 min before carefully removing all the dams Place the electrode plate on top of the cartridge and add 5 ml 0 25xTBE buffer to Chambers A B C D and E and 4 ml to Chamber F Add 60 ul of buffer to the extraction well and seal it with PCR tape Use the extraction well tool to press down on the tape and ensure a good seal Add the 5ml sample to be concentrated lt 100 us cm into the sample chamber Prepare the Aurora Add 1 ml of water onto the center of the cold plate and load the cartridge Select and run the desired Aurora protocol 23
6. The gel will begin to set within minutes so ensure that this is done quickly To cast the sample gel pipette molten agarose into the sample gel region between the Type C and Type D gel dams on the far right side of the cartridge Use enough agarose to make the gel flush with the top of the cartridge typically slightly more than 1 ml Perform this step with the cartridge on a flat surface If any of the agarose leaks underneath a dam re adjust the dam and top up with agarose Figure 4 Casting the SCODA gel photograph Leave the cartridge on a flat surface at room temperature Visually inspect both gels for the presence of air bubbles The gel will begin setting immediately so if air bubbles are present immediately add more molten agarose Let the gel set for 20 min Carefully remove all the gel dams around the concentration gel by pulling them straight up while taking extreme care to ensure that the gel is not disturbed or delaminated from the plastic surfaces of the cartridge 13 e Carefully remove the gel dams surrounding the sample gel For the sample gel it is best to pull the dams horizontally away from the gel first and then pull them up this is to prevent the gel from being detached from the bottom of the cartridge which can result in sample loss e Use a spatula to remove any loose gel that may have leaked under the dams remove the extraction well post use gentle twisting motion to break the tension between
7. d set it aside The following steps should not be performed with the electrode plate installed Refer to Figure 2 and Figure 3 for insertion locations for each type of gel casting accessory Note that it is important to press the gel casting accessories down fully so that they create a good seal with the floor of the cartridge A good seal is essential to prevent leaks e Insert the extraction well post into the hole in the middle of the concentration gel region The post can be tight to insert Make sure the post goes all the way through the gel cavity and touches the floor of the cartridge o Acommon mistake is to not insert the post far enough which will result in a poorly formed extraction well e Insert 4 Type A gel dams into the grooves surrounding the gel octagon e Insert 2 Type B gel dams On the F buffer chamber side insert the gel dam about 4 5 mm away from the octagon wall at the location marked by etched lines on the reusable cartridge This gap will be used to cast the concentration gel o Inthe sample chamber insert a Type B gel dam flush against the octagon wall Insert the Type C gel dam to fit in the sample chamber the left side of the sample gel cavity e Insert the Type D gel dam to fit between the short walls on the right side of the sample gel cavity The cartridge should now resemble Figure 3 Ensure that the stainless steel tube and all the gel dams are vertical and in contact with the bottom surface of
8. der additional cartridges please contact support borealgenomics com This protocol uses the Aurora Reusable Cartridge part number 211 0004 AA D 22 Experienced User Protocol Please wear gloves at all times Materials required 10 11 12 0 2g agarose powder Lonza 5 LE Lonza Cat 50001 60ml 0 25xTBE running buffer Nuclease free water Decontaminated reusable cartridge and accessories e PCR tape and extraction well sealing tool In an Erlenmeyer flask add 20 ml 0 25xTBE buffer 0 26 agarose powder to make 1 gel Record the weight of the flask and heat the solution in a microwave until the powder has dissolved Note Only 5 ml is required for each cartridge Re weigh the flask and add nuclease free water to bring the flask back to its original weight Transfer the agarose to conical tube with a cap and incubate at 90 95 for 1 h After 1 h transfer the agarose into a 60 70 water bath and allow the temperature to equilibrate before casting Insert the gel casting accessories including the extraction post into the cartridge as shown below Type A Type C Type D Ts 9 JBQWES Sample Chamber ASHLEY f Extraction well post 9 _ Using a 1 ml pipette fill the concentration gel from the in Chamber F until the agarose is flush with the top of the cartridge
9. disposal Troubleshooting Please see the Aurora User Manual for more information about troubleshooting instrument faults Troubleshooting information related to processing your sample can be found in your protocol documentation 1 The Aurora or the camera does not connect to the computer 20 Unplug the instrument s USB cable wait five seconds and reconnect the cable 2 A cartridge fails a contact test Before each run the Aurora checks to make sure the instrument has good electrical contact with the cartridge Poor contact can be caused by misalignment of the cartridge Re seat the cartridge firmly within the registration features on the cold plate Check that the correct contact plate is installed If your contact plate has spring pin electrodes check to ensure that none of the spring pins are jammed in the up position If you notice stuck pins see the Aurora manual for cleaning instructions If your contact plate has coiled spring electrodes check to make sure there is nothing blocking contact with any of the springs and the graphite electrodes on the cartridge such as PCR tape or salt deposits 3 sample current is below minimum current limit warning appears The Aurora may not be making electrical contact with the cartridge Pause the run open the cartridge drawer check that the cartridge is firmly seated within the registration features on the cold plate close the cartridge drawer and press the play button
10. h 2 alignment pins pre inserted Reusable cartridge bottom Extraction well post Cleaning brushes Sheets PCR tape MicroAmp Optical Adhesive Film No image Spare graphite electrodes Type A gel dams e A type gel dams are coloured RED e Note A type dams are thinner than B type dams Type B gel dams e B type gel dams are coloured GREEN e Note B type dams are thicker than A type dams Type C gel dams e C type gel dams are coloured YELLOW e Note C type dams are thicker than D type dams Type D gel dams e D type gel dams are coloured BLUE e Note D type dams are thinner than C type dams Reagents required The following materials are required for each Aurora Reusable Cartridge These values assume you are making 195 agarose gel with 0 25x TBE running buffer Scale these values up to prepare enough reagents for multiple cartridges Molten agarose can be incubated in a water bath for up to three days prior to use Amount required per cartridge Agarose powder Lonza SeaKem LE Lonza Cat 50001 0 05 10x TBE Ambion Cat AM9863 1 25 ml Nuclease free water 48 75 ml Procedure overview e Prepare buffer e Prepare agarose e Prepare the sample e Prepare the cartridge e Cast agarose gel Fill buffer chambers Load the sample e Prepare the Aurora Begin the run e Sample extraction Preparing buffer This section describes the steps and materials required to prepare buffer for use wit
11. h the reusable cartridge Materials e TBE buffer stock Boreal Genomics recommends Ambion 10x TBE Ambion catalogue number AM9863 Nuclease free water e Optional Polystyrene cell culture flask Boreal Genomics recommends Costar 225 Cell culture flask Corning catalogue number 3000 Time required Approximately 5 min hands on time Notes e For sensitive or low copy DNA samples it is recommended that all handling steps be carried out in a biosafety laminar flow hood and that all glassware be autoclaved to avoid any exogenous DNA contamination Boreal Genomics protocols typically require 0 25x TBE buffer It is possible to prepare reusable cartridges with different buffer strengths consult Boreal Genomics for further details e tis recommended that buffer be prepared in bulk in advance e Buffer is used both to prepare agarose gel and to fill the buffer chambers of the reusable cartridges Each reusable cartridge run requires a total of about 50 ml of buffer Procedure e Dilute 10x TBE in nuclease free water to a concentration of 0 25x to the desired final volume A minimum of 50 ml of buffer is required for each cartridge however more can be made in advanced for multiple preparations e Optional to further sterilize the buffer fill a cell culture flask up to a quarter of its capacity ex 125 ml of a 500 ml flask place the flask containing buffer under UV light on a rotating platform overnight It is essen
12. he extraction well e The expected output volume is 50 60 ul but may vary from 40 70 ul depending on sample and run conditions Cleaning cartridges and accessories Important The user is responsible for the safe use transport storage and disposal of any materials that may be considered a chemical or biological hazard Refer to accompanying material safety data sheets MSDS for safety information and handling instructions and comply with all federal state provincial municipal local and institutional requirements and guidelines for disposal Materials required Boreal Genomics recommends the Ultra Lum UVC 508 UV crosslinker set at the maximum energy setting 999 Joules for all UV irradiation steps The total accumulated intensity over 10 min is approximately 4 2 J cm at this setting Important Note Regarding Cartridge Durability Never expose cartridges to ethanol which causes cracks in the acrylic It is important not to soak the cartridges in liquids for extended periods of time as part of the cleaning and decontamination procedure Do not expose the cartridge to high temperatures and do not use heat as part of the cleaning or drying procedure Extended soaking periods or exposure to heat can damage the cartridge Take care not to scratch the plastic when cleaning the cartridges in particular the thin bottom layer of plastic that is in contact with the aluminum bottom of the cartridge 18 Cleaning the cartridge Deca
13. nspection Inspect the empty sample chamber prior to loading your sample If any buffer has leaked into the sample from the other reservoirs it is best to re cast the gel s to avoid loss of sample during the run For optimal results the sample should be loaded and the run started as quickly as possible Optional As an added precaution to reduce the risk of DNA contamination cut a piece of PCR tape large enough to cover the sample chamber Remove the white backing from the adhesive film and carefully lay it over the sample chamber from left to right while leaving a small air gap between the concentration gel and the sample chamber to relieve any pressure during the run Use a scalpel blade and forceps to cut away and remove any tape that may be covering any of the electrodes To seal the tape use a PCR paddle or a flat object to seal the edges take care to avoid any wrinkles or bubbles 15 Adhesive film Figure 6 Cartridge with adhesive film over extraction well 16 Extraction well sealing tool Figure 7 Extraction well sealing tool aligned and uncompressed left and fully compressed right Load the sample Bring the volume of the sample you prepared earlier up to 5 ml with nuclease free water Transfer the entire 5 ml sample into the empty sample chamber see Figure 1 Close the cartridge drawer Prepare the Aurora Prepare the Aurora and chiller as described in the user manual Start the chiller and ensure that a
14. nt and dispose of the buffer from the cartridge accordingly If the run has not been stained with a hazardous dye it is okay to dispose of it down a sink with running water Using the cleaning brushes provided gently break up and remove the sample gel and concentration gel Use warm running tap water to help remove the concentration gel if necessary Reminder It is very important to take care not to scratch the bottom layer of plastic in the cartridge Do not scour or scratch the plastic Do not use brushes or other cleaning implements with sharp edges or points The layer of plastic separating the gel and buffer in a cartridge from the aluminum plate on the bottom of the cartridge is very thin and if it is scratched it may be necessary to replace the cartridge Fill the cartridge with a 10 v v solution of household bleach 5 sodium hypochlorite in deionized water and let it soak for 30 min Do not soak for extended periods of time as this can damage the cartridge Rinse the cartridge thoroughly with deionized water and then let the cartridge air dry or use pressurized nitrogen or filtered air Optional Once the cartridge is dry subject it to UV irradiation for 10 min to further minimize contamination For the most demanding applications with very low copy number DNA samples extend the duration of UV exposure to 30 min for thorough decontamination Note Repeated exposure of the cartridge to bleach and UV irradiation will even
15. ransfer the agarose to a water bath at 60 70 Allow the temperature to equilibrate and leave the agarose in the water bath until use Notes e Aurora protocols usually require 1 agarose 0 25x TBE It is possible to prepare reusable cartridges with different agarose percentages consult Boreal Genomics for further details e Molten agarose should not be stored for more than 3 days before use Discard any agarose which has been stored for more than 3 days o Using agarose made on the same day results in optimal gel characteristics Preparing the sample Please see your Aurora protocol documentation for details on the method of preparing your sample prior to loading it into the Aurora cartridge Preparing the cartridge Alignment pin Extraction well Buffer chamber D Buffer chamber Buffer chamber E Buffer chamber Buffer chamber Concentration gel Buffer chamber A Alignment pin Figure 1 Top view of the cartridge Inspecting the cartridge Before beginning cartridge preparation check that The cartridge and accessories have been cleaned Refer to the section titled Cleaning Cartridges and Accessories for instructions The graphite electrodes are not chipped or cracked e The cartridge is not damaged or cracked Materials required e Geldams e Extraction well post Time required Approximately 5 minutes of hands on time Procedure Begin by removing the electrode plate from the cartridge an
16. should stick up above the cartridge slightly to allow for easier removal of the adhesive film after the run With a gloved finger firmly press down on the film ensuring a good seal on all edges and taking care to avoid wrinkles and bubbles e Align the extraction well sealing tool to the extraction well as shown in Figure 7 left Firmly press down on the tool until it is fully compressed as shown in Figure 7 right Release and then press down a second time to ensure a good seal Load the cartridge into the Aurora instrument e Pull gently outward at both left and right sides of the cartridge drawer until the drawer slides out and latches in the open position 14 Examine the cold plate and the metal bottom of the cartridge for debris that may prevent the cartridge from sitting flat on the cold plate Remove any debris that is found e Pipette 1 ml of water onto the center of the cold plate and place the cartridge onto the cold plate oriented so the concentration gel is on the left hand side as pictured in Figure 5 e Ensure that the cartridge is sitting flat on the surface of the cold plate and is not resting on top of the cartridge registration features These steps ensure good thermal contact between the cartridge and cold plate Cartridge Cartridge SS gt registration features ED Cartridge drawer Figure 5 Cartridge oriented correctly on the cold plate Final cartridge i
17. small drill bit or similar thin metal object to force out the graphite electrodes from the electrode plate Wash or wipe the electrode plate clean using deionized water e Press fresh graphite electrodes into the appropriate holes in the electrode plate from the bottom side of the electrode plate the side where the white alignment pins protrude The electrodes should be pressed into the holes by hand for the first few millimeters at least Pushing the electrodes down against a flat surface may be required to press them in fully Push the electrodes in until they are flush with the top surface of the electrode plate e Clean off any graphite debris that may have flaked off during the process Contact Boreal Genomics for replacement graphite electrodes Disposal Dispose of the cartridge and contents following all applicable policies laws and regulations Aurora cartridges buffers and gels are non hazardous as shipped however cartridges that have contained hazardous samples including many nucleic acid stains may be considered hazardous in your jurisdiction Important The user is responsible for the safe use transport storage and disposal of any materials that may be considered a chemical or biological hazard Refer to accompanying material safety data sheets MSDS for safety information and handling instructions and comply with all federal state provincial municipal local and institutional requirements and guidelines for
18. the cartridge 10 Type Type D 2 Sample Chamber Jaques Extraction well post 0 gt Type Figure 2 Cartridge showing locations of gel dams diagram 11 Figure 3 Cartridge with gel dams inserted photograph Casting agarose gel Materials required o Molten agarose TBE solution at the desired buffer concentration P1000 or larger pipette Time required Approximately 10 min hands on time plus 20 min hands off time Procedure To cast the concentration gel use the pipette to transfer molten agarose into the 4 5 mm gap between the left Type B dam and concentration gel area until the whole concentration gel area is filled with gel see Figure 4 and there are no voids present in the concentration gel To facilitate casting and avoid air bubbles it may be possible to tilt the cartridge to the right and not fully expel the agarose from the pipette tip at one time The 4 5 mm gap should be filled with gel also until the agarose is flush with the top of cartridge 12 Slightly more than 2 ml of agarose is required for this step but may vary based on gel dam placement and any leakage that occurs Add enough agarose so that the gel fills all corners of the gel volume Immediately check for any air bubbles or leaks If either is present make any necessary gel dam adjustments and top off any lost agarose
19. tial that the flask is transparent to UV so that the UV can penetrate the buffer for efficient irradiation Preparing agarose This section describes the steps and materials required to prepare agarose gel for use with the reusable cartridge Materials e Agarose powder Boreal Genomics recommends Lonza SeaKem LE Lonza catalogue number 50001 e TBE buffer prepared in previous step Time required Approximately 15 min hands on time plus 1 h hands off time Procedure Prepare 1 w v agarose gel by adding 0 05 agarose and 5 ml 0 25x TBE made in the previous step in an Erlenmeyer flask It is recommended that you scale these numbers up to make extra agarose to have on hand in case gels need to be recast for any reason such as small leaks etc or if you intend to run multiple cartridges e Weigh the flask containing the agarose solution before heating and record the weight minimize evaporation cover the flask loosely with a lab tissue and heat the solution in a microwave oven until the gel has completely dissolved without boiling over e Weigh the flask after heating and add nuclease free water to replace water lost to evaporation bringing it back up to its original weight o Transfer the agarose to a conical tube with a cap to avoid further evaporation and incubate the molten agarose at 90 95 for 1 hour This leads to improved DNA recovery and it is recommended that this step is not omitted After 1 hour t
20. to resume If the cartridge fails the contact check see above 4 A temperature controller error appears Make sure the chiller is and operating If you see a the display the chiller is pumping coolant but temperature control is not active Press Start Stop on the chiller to enable temperature control 5 Error The Aurora control software warns that the sample is too conductive Running high conductivity samples will result in lower yields and may cause gel damage and other issues during the run The Aurora instrument will give the warning Injection Conductivity test failed Sample conductivity is too high Injection might fail for highly conductive samples Conductivity for 5 ml sample should be lt 100 uS cm Please refer to the Troubleshooting section in your Protocol document for further instructions on reducing sample conductivity 6 Error The Aurora control software reports Run Screen Error Messages or RTEO31 These errors may indicate that the Aurora reusable cartridge has been damaged Inspect the cartridge for cracks or scratches in the bottom layer of plastic The cartridge can be filled with water and left on top of a paper towel to look for any leaks that may be present Leaks scratches or cracks that lead to these errors may require that the cartridge be replaced Contact Boreal Genomics for assistance 21 Ordering and support For support for Aurora protocols or cartridges or to or
21. tually lead to degradation of the plastic and the cartridge will have to be replaced Visible cracks in the plastic or repeated leaks or instances of Run Screen Error Messages RTEO30 or RTEO31 may indicate that a cartridge has worn out or been damaged and should be replaced Cleaning the casting accessories Remove any visible debris or dried gel from the gel dams and extraction well post Soak the gel dams and extraction well post in 10 household bleach for 10 30 min Do not soak for longer than 30 min Rinse all accessories repeatedly with deionized water followed by a rinse and 10 min soak in deionized water Let the accessories air dry Optional Once the accessories are dry expose them to UV irradiation for 10 min on each side Cleaning the electrode plate e Wipe the electrode plate down using 10 household bleach Take care to avoid snapping the graphite electrodes e Rinse the electrode plate thoroughly with deionized water and soak in deionized water for 10 30 min Let the electrode plate air dry or use pressurized nitrogen or air to dry it e Optional Expose the electrode plate to UV irradiation for 10 min electrode side up 19 Replacing graphite electrodes The graphite electrodes on the electrode plate should be replaced if substantial wear or pitting is visible or if the electrodes become chipped or broken A rough surface finish on the graphite electrodes is normal To replace the graphite electrodes Usea
Download Pdf Manuals
Related Search