Plasma Display Stand
Contents
1. display to a wall pillar or other strong place or use the holes on the back on the stand to fix to a table etc Do no use with the separately sold ceiling mount unit or wall mount unit Pay attention to the rope when moving the Plasma Display The screws for fastening the display to the wall a pillarora stand are not F included Please obtain screws suited for the surface on which the display is to be mounted gt Assembling the stand Preparations e e Unpack the plasma display 1 Open the top of the cardboard in which the plasma 2 Remove the cardboard from the top and open display is packed and remove the three pieces of the protective sheet styrofoam Styrofoam t lt Protective sheet 1 Open the package and take out the cardboard and accessories screws and handling instructions Package Cardboard Shock absorbing boxes Screws Instruction manual Bar covered with a protective sheet Feet covered with a protective sheet Shock absorbing boxes Assembling the stand 2 Take out the bar and remove the shock ab sorbing boxes from both sides 3 Remove the two boxes containing the feet and set them upside down Assembling the stand 4 Lift up the protective sheet covering the foot starting from the perforated line in the center to reveal the mount ing surface Perforated line 5 R2. d tighten them using the included screwdriver Tighten the screws immediately after placing the display on the stand If not the display could tip over resulting in injury
3. e Plasma Display to tip over resulting in injury Do notuse damaged parts Doing so could cause the Plasma Display to tip over resulting in injury If a partshould be damaged contact the store of purchase Each unitis designed specifically for use with M ARAN TZ 61 nch plasma displays Please do not mount any other equipment with these items Doing so may cause the item to fall over and result in injury Do notseton shaky stands tilted surfaces or other unstable places Doing so could cause the Plasma Display to tip over or fall resulting in injury Moreover Do not install into a vehicle 0 OOO gt a gt Always Heed the Following Z CAUTIONS Do not obstruct the Plasma Display s ventilation holes If the ventilation holes are covered the heat will build up inside and this could lead to fire For example do not install the Plasma Display in narrow spaces where ventilation is poor do notplace covers over it etc Do not install the Plasma Display near air conditioner air outlets or in places where vibrations are strong Doing so could lead to fire or electric shock Do notinstall the Plasma Display in humid or dusty places or places exposed to soot or vapor such as in kitchens near humidifiers etc Doing so could lead to fire Do not install the Plasma Display outdoors Doing so could lead to fire or electric shock 50mm 1 97inch W hen installing the Plasma Display leave suf
4. emove the cover of the bar removed in step 2 insert the bar on the guide pins and tighten with the included stand assembly screws Kg Tighten the screws securely If not the monitor could tip over resulting in in jury guide pins 6 Grasp the two boxes containing the feet and turn them upside down again Assembling the stand 7 Lift the section stuck into the slit upwards pull it out then fold it down 8 On the bar side after pulling out the slit section bend as shown in the diagram then fold down 9 Fold down the front and rear of the box and remove the stand Remove the cover from the foot Mounting the plasma display on the stand 1 Insert the plasma display into the stand Check that the stand and plasma display are facing the proper direction then insert the plasma display into the stand This procedure should be done by atleast three persons since the plasma display is heavy and has a high center of gravity Hold the bottom and the grips on the back of the plasma display and support the top when inserting the plasma display into the stand Hold both sides of the plasma display and liftitup then place the plasma display onto the stand so that the holes located at the bottom of the display engage with the stand 2 Fasten the plasma display and stand Pulling the top of the plasma display forward insert the four included display mounting screws into the holes in the stand an
5. ficient space around it as shown in the diagram Failure to do so could cause heat to build up inside leading Poa for sdm wall to fire 50mm 1 97inch Hold the Plasma Display securely when mounting the units on it Failure to do so could cause the Plasma Display to fall resulting in injury W hen installing the Plasma Display on a stand with casters be sure to block the casters If the stand should move the Plasma Display could fall resulting in injury The Plasma Display is heavy so be sure to install in a stable place and take measures to preventit from tpping over and causing injury The Plasma Display has a high center of gravity Itshould be unpacked and moved by a minimum of two people holding it atthe top and bottom Failure to do so could cause the Plasma Display to fall resulting in injury gt gt 0 0 Avoid dusty or humid rooms and rooms filled with soot or cigarette smoke The Plasma Display s screen could get dirty resulting in poor picture quality Avoid places where the screen is exposed to direct sunlight or strong artificial light If surrounding light should shine on the screen the screen will appear white and be hard to see Do not install in places where the temperature is high or low Doing so could result in damage Additional fall prevention measures Either use the tip prevention fitting included with the display to fix the plasma
6. marantzZ Plasma Display Stand Handling Instructions AS6150 Thank you for purchasing the AS6150 Plasma Display Stand Before using this product please read this Handling Instructions thoroughly so that you can use this product at its full functionality After reading retain this manual in an easily accessible location so that you can refer to this manual whenever you have a problem or trouble during use This plasma display stand is designed specifically for use with M A RAN TZ 61 inch plasma displays Special skills are required to install the Plasma Display Do not attempt to install the Plasma Display on your own Attention Sales Agents and Technicians To ensure the user s safety be sure to select a place sufficiently strong to bear the weight of the Plasma Display and the different units Installation should be performed by a minimum of three persons Be careful not to lose removed screws etc Parts Included Feet 2 cK Bar 1 Stand assembly screws M4 x 10 8 Handling instructions VrO TNTS Screwdriver these instructions Display mounting screws M6 x50 4 gt Specifications M odel AS6150 External dimensions W 1125 x H 205 x D 430 mm W 44 3 x H 8 1 x D 16 9 inchs Weight 6 5 kg 14 3 lbs O perating conditions Temperature 0 to 40 C 32 Ft0104 F Humidity 20 80 Storage conditions Temperature 10 to 50 C 14 F to 122 F Humidity 10 90 41AW851010 Always Heed
7. the Following Before Use Symbols Various symbols are used in this Handling Instructions for the safe and proper use of the product as well as preventing any injury or damage to persons or property These symbols and their meanings are described below Please have a good understanding of these matters before reading the main text of the manual Ignoring this indication and improper handling could be the cause of per WARNING N Ses eae j sonal injury such as a serious injury or death CAUTION A Ignoring this indication and improper handling could cause injury to a per son or damage to the surrounding household belongings Examples of Symbols A A This symbol informs that there are contents that demand caution including warnings Concrete details of the caution are written within the diagram S amp This symbol indicates a prohibited matter Concrete details of the prohibition are written within the diagram Q This symbol indicates something that must be done Concrete details of the prohibition are written within the diagram A WARNING Be sure to have the Plasma Display installed by your store of purchase following the instructions in this manual If installed incorrectly the Plasma Display could tip over resulting in injury To ensure safety tighten bolts and screws securely Failure to do so could cause the Plasma Display to tip over resulting in injury Do not modify parts Doing so could cause th
Download Pdf Manuals
Related Search