Protects your digital signage displays from power spikes.
Contents
1. About Black Box Black Box Network Services is your source for more than 118 000 networking and infrastructure products You ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free live 24 7 Tech support available in 30 seconds or less O Copyright 2011 Black Box Corporation All rights reserved DSPF3 S7 120V rev 1 724 746 5500 blackbox com2. Output Power LED is illuminated If this green LED is not illuminated verify that 120 V is available at the receptacle that the filter is plugged into Wiring Fault When the red Wiring Fault LED is illuminated the receptacle that the filter is plugged into may not be correctly connected to the system safety ground or may be cross wired line to neutral The red LED will light momentarily when power is first applied to the filter but should immediately turn off if the receptacle is wired correctly in accordance with the U S National Electric Code and local electrical codes If the red Wiring Fault LED remains illuminated contact a qualified electrician to identify any wiring discrepancies Black Box recommends using electrical testing equipment to verify proper electrical wiring Filter Disposal When your filter has reached the end of its useful life you will need to dispose of the unit For proper disposal contact your local recycling reuse or hazardous waste center Do not discard waste electrical or electronic equipment WEEE in the trash Dispose of the unit in accordance with local national recycling or disposal ordinances Page 14 724 746 5500 blackbox com DSPF3 57 120V NOTES DSPF3 S7 120V 724 746 5500 blackbox com Page 15 Black Box Tech Support FREE Live 24 7 Tech support the way it should be EN d E Great tech support is just 30 seconds away at 724 746 5500 or blackbox com lt BLACK BOX
3. 1 Specifications 1 Specifications 1 1 Electrical Allowable Load Current Crest Factor lt 4 1 Allowable Load Power Factor 0 3 leading to 0 3 lagging Current Maximum Continuous RMS 7 amps Efficiency gt 98 Frequency 60 Hz Input and Output Power Input 1 5 15P plug on a 6 ft 1 8 m power cord Output 3 5 15R receptacles on a 6 inch 15 2 cm cord Overcurrent Protection Push to reset circuit breaker Overload Capacity 1 Second 1000 Surge Let through Voltage Any Input Mode ANSI IEEE C62 41 Cat A Ringwave Normal Mode L N lt 20 V Common Mode N G lt 20 V Topology TVSS with filter UL VPR lt 330 V Voltage 120 V 1 2 RJ 11 Communications Line Protection Classification Secondary protector Surge Let through Voltage Any Input Mode Volts 10 x 100 us 1500 V 100 A Waveform lt 370 V metallic mode T R and lt 370 V longitudinal mode T G or R G Topology POTS and ADSL compatible 1 3 Data Line Protection Classification Isolated loop Topology 10BASE T 100BASE T 1000BASE T Gigabit Ethernet compatible Connectors ElA TIA 568A 8 position modular jack in and out Ad 724 746 5500 blackbox com Page 9 Chapter 1 Specifications 1 4 Operating Environment Elevation 10 000 ft 3000 m ASL Temperature 32 to 104 F 0 to 40 C Humidity 5 to 95 noncondensing 1 5 Safety Listings UL 1449 1283 1363 FCC Part 68 EMC N A 1 6 Physical Indicators 2 LE
4. DSPF3 S7 120V lt BLACK BOX Protects your digital signage displays from power spikes Customer Order toll free in the U S Call 877 877 BBOX outside U S call 724 746 5500 Support FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax Information 724 746 0746 Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 Web site www blackbox com E mail info blackbox com Important Safety Instructions Regulatory Compliance IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Please read and save these instructions This manual contains important instructions for the Digital Signage Power Filter DSPF3 S7 120V Follow these instructions during the unpacking installation and maintenance of the filter If you have a problem with the filter refer to this manual before calling Black Box Technical Support at 724 746 5500 or info blackbox com WARNING Dangerous voltages are present within this unit There are no user serviceable parts within this unit therefore any repairs or modifica tions may result in unsafe electrical conditions or violation of electrical code UL Compliance The Digital Signage Power Filter DSPF3 S7 120V complies with UL 1449 1283 and 1363 standards CE Mark CE WEEE ROHS When your filter has reached the end of its useful life you will need to dispose of the unit For proper disposal contact your local recycling reuse or hazardous wa
5. Ds 1 power available green 1 wiring fault red Size With bracket 2 7 H x 3 9 W x 9 9 W 6 9 x 9 9 x 25 2 cm Without bracket 2 4 H x 3 9 W x 7 4 D 6 1 x 9 9 x 188 cm Weight Net 2 75 Ib 1 25 kg Shipping 4 5 Ib 2 04 kg Page 10 724 746 5500 blackbox com DSPF3 S7 120V Chapter 2 Overview 2 Overview 2 1 Introduction Use the Digital Signage Power Filter to protect your digital signage displays from power spikes This filter works with any type of monitors HDMI DVI etc 2 2 What s Included Your package should include the following items If anything is missing or damaged contact Black Box Tech Support at 724 746 5500 or info blackbox com e Digital Signage Power Filter with integral cord with 1 NEMA 5 15P plug on a 6 foot 1 8 m cord and 4 NEMA 5 15R receptacles on a 6 15 2 cord e This user s manual 2 3 Hardware Description Figure 2 1 illustrates the Digital Signage Power Filter and describes its components 5 15P power plug on a 6 foot Output 1 8 m cord Power LED Wiring Fault LED Circuit breaker located on side of Telephone line protector Network cable protector 3 NEMA 5 15R power receptacle assembly on a 6 inch 15 2 cm cord Figure 2 1 Digital Signage Power Filter DSPF3 57 120V 724 746 5500 blackbox com Page 11 Chapter 3 Installation and Operation 3 Installation and Operation CAUTION Indoor use only Install in a protected environment P
6. ace the filter in position and install two 8 or 10 wallmounting screws at the other end Tighten all four wallmounting screws to secure the filter 6 Plug the filter into a grounded receptacle properly wired in accordance with the U S National Electric Code and local electrical codes NOTE The Output Power LED green should be illuminated and the Wiring Fault LED red should not remain illuminated see Figure 2 1 If the correct status is not indicated first verify that AC power is available and the receptacle is correctly wired 7 Plug your equipment into the receptacle s of the filter Note that the total current required by your equipment must not exceed the filter s current rating as listed on the unit s nameplate Operate your equipment as usual DSPF3 S7 120V 724 746 5500 blackbox com Page 13 Chapter 3 Installation and Operation Overcurrent Protection If the current required by your equipment exceeds the filter s maximum current rating the circuit breaker will trip To reset the circuit breaker unplug your equipment from the filter and reset the circuit breaker switch If the circuit breaker continues to trip once it has been reset disconnect the equipment that is causing the overcurrent condition Status indicators The filter features two status indicator LEDs Output Power and Wiring Fault see Figure 2 1 Output Power AC power is available at the output receptacle s of the filter when the green
7. he interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of Industry Canada Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe A prescrites dans le Reglement sur le brouillage radio lectrique publi par Industrie Canada FCC Part 68 This product complies with Part 68 of the FCC rules and the requirements adopt ed by the ACTA On the case of this product is a label that contains among other information a product identifier in the format US AAAEQ TXXXxX If requested this number must be provided to the telephone company This product may use one or more of the following Universal Service Order Code USOC jacks RJ 11 A plug and jack used to connect this equipment to the premises wiring and tele phone network must comply with the applicable FCC Part 68 rules and require ments adopted by the ACTA A compliant telephone cord and modular plug may also be provided with this product It is designed to be connected to a compatible modular jack that is also compliant See installation instructions for details Page 4 724 746 5500 blackbox com Depa iat FCC Statement The REN is
8. lephone network the telephone company may request that you disconnect the equipment until the problem is resolved There are no user serviceable parts in this equipment FCC Part 68 9 Connection to party line service is subject to state tariffs Contact the state public utility commission public service commission or corporation commission for information If your site has specially wired alarm equipment connected to the telephone line ensure the installation of this product does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company or a qualified installer Ad 724 746 5500 blackbox com Page 5 NON Statement Normas Oficiales Mexicanas NOM Electrical Safety Statement INSTRUCCIONES DE SEGURIDAD 1 Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado 2 Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura 3 Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas 4 Todas las instrucciones de operaci n y uso deben ser seguidas 5 El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc 6 El aparato el ctrico debe ser usado nicamente con carritos o pedestales que sean recomendados por el fabrican
9. o El equipo el ctrico debe ser limpiado nicamente de acuerdo a las recomendaciones del fabricante En caso de existir una antena externa deber ser localizada lejos de las lineas de energia El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci n Servicio por personal calificado deber ser provisto cuando A El cable de poder o el contacto ha sido da ado u B Objectos han ca do o l quido ha sido derramado dentro del aparato o C El aparato ha sido expuesto a la lluvia o D El aparato parece no operar normalmente o muestra un cambio en su desempe o o E El aparato ha sido tirado o su cubierta ha sido da ada Ad 724 746 5500 blackbox com Page 7 Table of Contents Table of Contents 1 SpecificatONS PPP CO UN O o sate da 9 1 1 Electrica aia 9 1 2 RJ 11 Communications Line Protection ooonncinnicnnncincconncccinnccccnnnncinos 9 1 3 Data Line Protection mociones EA AVi 9 1 4 Operating EMVIFOMIMENE ainia chantas 10 1 5 Safety LISTOS iii idolo 10 AR e E A E vanessa EEE ES 10 AS a a a bhausy i aaae eaea 11 21 INOdUCOM assirian an eee et 11 22 Whats Included ri e asa 11 23 Hardware Description micosis a n at 11 3 Installation and Operan estrias ltd 12 Page 8 724 746 5500 blackbox com DSPF3 57 120V Chapter
10. osition the Digital Signage Power Filter on a desktop or mount it on a wall Be sure to mount it where it does not interfere with the input and output cords or access to the circuit breaker or indicators Make sure it is within safe reach of the wall receptacle NOTE When mounting the unit on the wall or any other surface you can position it in any direction For mounting to a wall or other surface follow the directions below You will need the following for wall or surface mounting e Digital Signage Power Filter e Mounting bracket kit included this kit includes screws to attach bracket to unit e 4 8 or 10 screws not supplied e 4 wall anchors capable of supporting the filter s weight if attaching to drywall not supplied e This user s manual 1 Using the mounting bracket supplied as a template mark the locations for drilling mounting holes in the surface to which it will be attached 2 Drill the holes and install the wall anchors if needed 3 Attach the mounting bracket to the filter using the four screws provided see Figure 3 1 Page 12 724 746 5500 blackbox com DSPF3 57 120V Chapter 3 Installation and Operation Digital Signage Mounting bracket 4 8 or 10 1 screws 1 Figure 3 1 Attaching the mounting brackets to the filter 4 Install two 8 or 10 wallmounting screws at one end of the mounting area leaving Ys clearance between the screw head and the surface 5 Pl
11. ste center Do not discard waste electrical or electronic equipment WEEE in the trash Dispose of the unit in accordance with local national recycling or disposal ordinances RoHS Page 2 724 746 5500 blackbox com DSPF3 57 120V Trademarks Used in this Manual Trademarks Used in this Manual Black Box and the Double Diamond logo are registered trademarks of BB Technologies Inc UL is a registered trademark of Underwriters Laboratories Inc Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners Ad 724 746 5500 blackbox com Page 3 FCC and IC RFI Statements FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be necessary to correct t
12. te 7 El aparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante 8 Servicio El usuario no debe intentar dar servicio al equipo el ctrico m s all lo descrito en las instrucciones de operaci n Todo otro servicio deber ser referido a personal de servicio calificado 9 El aparato el ctrico debe ser situado de tal manera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sof alfombra o superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n 10 El equipo el ctrico deber ser situado fuera del alcance de fuentes de calor como radiadores registros de calor estufas u otros aparatos incluyendo amplificadores que producen calor 11 El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato 12 Precauci n debe ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada Page 6 724 746 5500 blackbox com DSPF3 57 120V 13 14 15 16 17 18 NOM Statement Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y recept culos donde salen del aparat
13. used to determine the number of devices that may be connected to a telephone line Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call In most but not all areas the sum of the RENs should not exceed five 5 0 To be certain of the number of devices that may be connected to a line as determined by the total RENs contact the local telephone company The REN for this product is part of the product identifier that has the format US AAAEQ TXXXX The digits represented by are the REN without a decimal point e g 03 is a REN of 0 3 If this equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required But if advanced notice is not practical the telephone company will notify the customer as soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe it is necessary The telephone company may make changes in its facilities equipment operations or procedures that could affect the operation of the equipment If this happens the telephone company will provide advance notice for you to make necessary modifications to maintain uninterrupted service If you experience trouble with this telephone equipment contact Black Box Tech Support at 724 746 5500 or info blackbox com for information on obtaining service or repair If the equipment is causing harm to the te
Download Pdf Manuals
Related Search