Home

User Manual for Model MPR-715F-PA Biomedical

1. The guideline for the maintenance 1s as follows lt gt The continued cleaning and check is recommended to keep the performance for long period Unit status Cleaning of exterior interior Once a month page 31 operation can be continued and accessories Defrosting freezer page 20 Stop of freezer operation Checking power supply cord page 32 Stop of operation Checking temperature recorder page 32 operation can be continued Stop of operation at maintenance Stop the operation by the procedure below before maintenance at the time of maintenance with no operation Put on the gloves Turn off the power switch Se ei Start the maintenance Turn off the battery switch if the battery for power failure 1s installed Disconnect the power supply plug from the power supply outlet 31 00 Cleaning exterior interior and accessories Use a dry cloth to wipe off small amounts of dirt on the outside and inside of the unit and all accessories If the outside panels are dirty clean them with a diluted neutral dishwashing detergent lt gt Undiluted detergent can damage the plastic components For the dilution refer to the instruction of the detergent After the cleaning with the diluted detergent always wipe it off with a wet cloth Then wipe off the cabinet or accessories with a dry cloth Important Never splash water directly onto the unit as this may cause electric shock or short ci
2. Door alarm 28 63 ACTION FOR ALARM WITH ERROR CODE Alarms involving an error code indicated on the temperature display are generated by the self diagnosis function Contact a Sanyo sales representative or agent without delay report the error code and request repairs Alternate display of error code E01 to E12 and chamber temperature indication blink of alarm indicator Intermittent tone of buzzer remote alarm linked Error code E01 Disconnection of refrigerator temperature display sensor lt gt Alternate display of E01 and 50 when the indicator for refrigerator temperature lights Error code E02 Short of refrigerator temperature display sensor lt gt Alternate display of E02 and 150 when the indicator for refrigerator temperature lights Error code E03 Disconnection of freezer temperature display sensor lt gt Alternate display of E03 and 1 50 when the indicator for freezer temperature lights Error code E04 Short of freezer temperature display sensor lt gt Alternate display of E04 and 150 when the indicator for freezer temperature lights Error code EOS Disconnection of frost sensor Error code E06 Short of frost sensor Error code E07 Disconnection of protective sensor for freezer compressor Error code E08 Short of protective sensor for freezer compressor Error code E10 Failure of fan motor for cooling circuit Error code E11 Disconnection of protective sensor
3. Table of contents Precautions for safe operation EE ee tee ee AEE OE EEA ee ee ne Tete ate ne ee re enn nem rT 1 Symbols for warning and caution verre eee Eee REE nent eee e eee eee ee ee eee eee EE EE EE eee EEE EE Ee RR RR RR eee tent eee 1 Warning and caution for handling the unit crrrcrrrrceete ee te ete eee r ee eee ee ee ee en ee eee e eee n sense eee e eee reser rer RR RR ers RR ers ens 2 Environmental conditions tet RR DDD nnn nnn e rskr nner neaeeee eee nana anna nn ana RAR KRA KRA RKA ARR ARR Rss 5 Precautions and action for temperature FISCO sereeeeeeeerereeeeeeeeeenererrereeeeeeeeeerererrr rer re era cen ce recon RR RR RR KRK RR RR RR acerca 6 Precautions for temperature 1 I eee oe er RR rr RR RR RR RR KR Kerr ers 6 Action for chamber temperature 10 I wee R KRK EEE sr rests 7 Refrigerator components E 8 Main body EEE ZE 8 Control panel don a es re ed sed nine de dai a Guia 10 Check of enclosures ss sssssssseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeneeeeeeeeeeeeeeneeeneneeeneeeeeeeneneeeenne 12 Start up procedure ee Rene Re nr er ER ee er tee ne Ale ee rr BARS rece ee A 13 Handling of storage items EEE EE EE EEE EE EE EEE EEE EEE EEEEEEEEEEEEEEEEEEEECEEEEEEEEEEEEEEECCEEEEEECEEEEEEEECEEEEEEEEEEEEEEEEEEEEEEEECEEEE 14 Initial setting setting range and function code seen 14 During after power failure iad eRe a Ne di a ei sde a a es nn de ni Laeken 15 Setting of chamber temperature ER asians 16 Lock of chamber temperature setting M AE A a ee a
4. Specifications will be subject to change without notice Performance specifications MPR 715F Maximum cooling performance Self diagnostic Refrigerator Chamber center temperature 2 C ambient temp 35 C no load Freezer Chamber center temperature 30 C ambient temp 30 C no load Temperature control range Refrigerator Between 2 and 14 C ambient temp 5 to 30 C no load Freezer Between 30 and 20 C ambient temp 5 to 30 C no load Specifications will be subject to change without notice lt gt The above data is measured based on our internal basis The unit with CE mark complies with EC directives 42 J Safety Check Sheet for copy 1 Used sample Risk of infection No possibility Some possibility Possible Risk of toxicity No possibility Some possibility Possible Radioactive material Not used Used Nuclide Other special instruction 2 Contamination of the unit Interior No contamination Decontaminated Some possibility of contamination Contaminated if decontaminated method Other contamination 3 Instructions for safe service maintenance of the unit a The unit is safe to work on b There is some danger The precaution or decontamination method is as follows Date Name amp Signature Division or department Telephone Name Model Serial number Date of installation Pharmaceutical MPR 715F refrigerator with freezer Request Please fil
5. gt A multiple tap may cause fire resulting from abnormal heating Connect the power supply plug to the power source firmly after removing the dust on the plug gt A dusty plug or improper insertion may cause a heat or ignition Never store corrosive substances such as acid or alkali in this unit if the container cannot be sealed gt These may cause corrosion of inner components or electric parts Check the setting when starting up of operation after power failure or turning off of power switch gt The stored items may be damaged due to the change of setting When moving the unit contact Sanyo sales representative or agent gt The moving by a user may cause damage or injury resulting from tipping over of the unit Prepare a safety check sheet when you request any repair or maintenance for the safety of service personnel gt Copy the Safety check sheet and hand it to a service personnel after filling the sheet 39 ENVIRONMENTAL CONDITIONS This equipment is designed to be safe at least under the following conditions based on the IEC 61010 1 m Indoor use m Altitude up to 2000 m m Temperature 5 C to 40 C m Maximum relative humidity 80 for temperature up to 31 C decreasing linearly to 50 relative humidity at 40 C m Mains supply voltage fluctuations up to 10 of the nominal voltage m Transient overvoltages up to the levels of overvoltage category Il m Temporary overvoltages occurr
6. lectriques et lectroniques en fin de vie doivent tre limin s separement des ordures m nageres Nous vous prions donc de confier cet quipement votre centre local de collecte recyclage Dans Union Europ enne il existe des syst mes s lectifs de collecte pour les produits lectriques et lectroniques usag s Aidez nous conserver l environnement dans lequel nous vivons Les machines ou appareils lectriques et lectroniques contiennent fr quemment des mati res qui si elles sont trait es ou limin es de mani re inappropri e peuvent s av rer potentiellement dangereuses pour la sant humaine et pour l environnement Cependant ces mati res sont n cessaires au bon fonctionnement de votre appareil ou de votre machine Pour cette raison il vous est demand de ne pas vous d barrasser de votre appareil ou machine usag avec vos ordures m nag res Spanish Los productos SANYO estan dise ados y fabricados con materiales y componentes de alta calidad que pueden ser reciclados y reutilizados Este s mbolo significa que el equipo el ctrico y electr nico al final de su ciclo de vida no se debe desechar con el resto de residuos dom sticos Por favor deposite su viejo televisor en el punto de recogida de residuos o contacte con su administraci n local En la Uni n Europea existen sistemas de recogida espec ficos para residuos de aparatos el ctricos y electr nicos Por favor ay denos a cons
7. a D REA Sin eee ee a de 17 Stop of freezer operation Sd jd E 18 Procedure to stop the freezer operation RR A REI RIR RN RP SRD NR CRT Tee DR re eT ere re rrr NA 18 Procedure to resume the freezer operation na anes cHDisDee uses arcesdesouer 19 Defrost ee er ee err ere errr re re er re rr ee re re K NS NR cre er rr rece errr er rer rr cer 20 Defrost in refrigerator ias dida dai a asd ni did ia ia amide Si a ira data ads 20 Defrost in freezer ss 20 Setting of alarm temperature dd a aa 21 Setting of high temperature alarm refrigerator EEE 21 Setting of low temperature alarm refrigerator TT Rbd a a a ua T 72 Setting of high temperature alarm freezer Sc ste PR ND 6 88 6 BIS CR O niet es se assises RP Obes E 23 Setting of low temperature alarm freezer EEE 24 Setting of buzzer suspended period DR EN A annma ee ee de 25 Troubleshooting ZE 26 Action for alarm seen eee eee eee ran ran ran eee eee eee eee nera rara eee een eee eee een eee eee e een AAA een RAKA een 28 Action for alarm with error code sense 29 Action for maintenance code seen 29 Safety fu nctions ssssssseseeeeeeneeneneeeneeeeeeeeeeneeeeeeeeeneeeeeeeeneeeeeneeeeeeneen een eee een eee e een enen eee 30 Routine maintenance ______wretrrttrtttteetttettretteetesetnetnneneeennennenseeenneneeesanessenseeeneasseeseecnnaseeseeeaeesseeseesanasseeseesaeesaeeseestaneseesanasaeeneacananans 31 Guideline for maintenance messes eseeseseseseesesesseseseseeeeeseeeeseseeeeeeeeeseeseeeeesesee 31
8. figure is changeable Ni Fo F q PAIN Change of second figure Nig The current setting 030 is displayed and the second figure 3 ser FT J blinks ia lt The initial setting 030 buzzer suspended period 30 minutes is Second figure is changeable displayed at the first setting after installation 6 Depress the up arrow key 6 times as needed for change A mI The display changes to 020 from 030 y Eu lt gt The figure changes between O and 6 by depressing the up arrow key 7 Depress the set key once The buzzer suspended period is memorized and the current chamber temperature is displayed on the temperature display Change of second figure SET Enter of the settin The setting mode returns to the temperature display mode automatically when 90 seconds has passed without any key operation auto return function In this case the setting 1s not accepted Important Never input any function code other than the specified one 25 60 TROUBLESHOOTING Check out the following before calling for service if the malfunction of the unit is suspected Attention Contact Sanyo sales representative or agent if the malfunction is not eliminated after checking the following items or the malfunction is not included in the following The unit does not operate at all O The capacity or voltage of the power source is not sufficient Use a dedicated power sourc
9. for refrigerator compressor Error code E12 Short of protective sensor for refrigerator compressor ll Action Contact a sales representative or agent ACTION FOR MAINTENANCE CODE Alternate display of maintenance code F1 and chamber temperature indication when the MPR 48B optional component is installed It is time to replace the battery for gt Contact a Sanyo sales representative or agent to replace power failure alarm about three years the battery for power failure alarm have passed with the power switch at lt gt The replacement of the battery for power failure alarm is a ON paid service Alternate display of maintenance code F2 and chamber temperature indication Contact a Sanyo sales representative or agent to replace the fan motor The replacement of the fan motor for cooking circuit is a paid service It is time to replace the fan motor for cooling circuit about six years have passed with the power switch at ON 29 64 SAFETY FUNCTIONS This unit has the safety functions shown below Even if under the safety operation there is no blink of display or indicator and no alarm buzzer operation Safety Situation Safety operation refrigerator only than about 28 C temperature rise Over cool protection The refrigerator temperature is lower refrigerator only than about 0 C avoid the temperature descent There 1s no key pressing for 90 The setting mode i
10. scroll key 10 Depress the up arrow key 5 times needed times for change The display changes to 20 from 25 The figure changes between 0 and 9 by depressing the up arrow key Change of first figure 11 Depress the set key once M DS ALI First figure is changeable I ry un N 7 SM The freezer temperature is memorized and the current freezer SET JL E temperature 1s displayed on the temperature display Enter of the settin The setting mode returns to the temperature display mode automatically when 90 seconds has passed without any key operation auto return function In this case the setting is not accepted 16 5l LOCK OF CHAMBER TEMPERATURE SETTING The chamber temperature setting can be locked to avoid an accidental change The change of chamber temperature setting is not accepted even if the key on the control panel is operated when the lock is ON Display Lock status Setting of chamber temperature Lock OFF Enable to change Lock ON Disable to change Example Change the lock of chamber temperature setting to ON from OFF factory setting x Following is an example Operate the key according to the desired lock status 1 Depress the scroll key for 5 seconds The current chamber temperature on the temperature display changes to LO and the first figure 0 blinks 2 Depress the up arrow key once Em Nig The display changes to L1 fr
11. set temperature is displayed i First figure is changeable at the first setting after installation 5 Depress the up arrow key 8 times as needed for change A The display changes to 03 from 05 0 TE y lt gt The figure changes between 0 and 9 by depressing the up arrow key Change of first figure 6 Depress the set key once The work temperature of low temperature alarm is memorized and the J current chamber temperature is displayed on the temperature display Enter of the setting The setting mode returns to the temperature display mode automatically when 90 seconds has passed without any key operation auto return function In this case the setting is not accepted Important Never input any function code other than the specified one 22 5 SETTING OF ALARM TEMPERATURE Setting of high temperature alarm freezer The abnormality chamber temperature rise is noticed by blinking of alarm indicator and chamber temperature display and sounding of the buzzer 15 minutes after blinking if the chamber temperature exceeds the set value of high temperature alarm Always set the high temperature alarm to protect the storage items from damage resulting from temperature rise E Setting range of work temperature for high temperature alarm Between 5 C and 15 C higher than the chamber set temperature E Initial setting factory setting 10 C higher than the chamber set temperature Example Change
12. the alarm temperature to chamber set temperature plus 5 C from chamber set temperature plus 10 C Details Change from the setting that the high temperature alarm works at 10 C higher than the chamber set temperature to the setting that the high temperature alarm works at 5 C higher than the chamber set temperature x Following is an example Operate the key according to the desired alarm temperature 1 Depress the temperature display changeover key to light the indicator for freezer temperature T 5 The current freezer temperature is displayed on the temperature display 2 Depress the up arrow key for 5 seconds FF The current chamber temperature on the temperature display changes yeu Sf to function code FOO and the first figure 0 blinks First figure is changeable 3 Depress the up arrow key 3 times A ET The display changes to F03 from FOO 0 E f The figure changes between 0 and 9 by depressing the up arrow key Change of first figure 4 Depress the set key once Lys The current setting 010 is displayed and the first figure 0 blinks set AU dO e FT The initial setting 010 low temperature alarm works when the chamber a temperature is 10 C higher than the chamber set temperature is displayed First figure is changeable at the first setting after installation 5 Depress the up arrow key 5 times as needed for change A i LI 19 The display changes to 015 from 010
13. 621LH MGR 4015LH every year For the replacement refer to the instruction manual enclosed with the temperature recorder 32 67 REPLACEMENT OF WEAR OUT PARTS Replacing the battery for power failure alarm Replace the battery for power failure alarm every 3 years when Fl and chamber temperature 1s displayed alternately to ensure the alarm is operated in the event of power failure Contact Sanyo sales representative or agent for the replacement of battery when F 1 and chamber temperature is displayed alternately lt gt The replacement of the battery for power failure alarm is a paid service The alarm function blink of alarm indicator sound of buzzer will not operate when the battery for power failure alarm is flat The alarm indicator blinks and the buzzer sounds by the battery for power failure alarm The regular replacement of the battery for power failure alarm is important to prevent the rise of chamber temperature in the case of unexpected situation N The replacement of the battery for power failure alarm should be WARNING executed by a qualified engineer or a service personnel only gt The replacement of the battery for power failure alarm involves the risk of electric shock Important The used battery is a recyclable precious resource Do not dispose of the battery Always follow the procedure for recycling Replacing the fan motor for cooling circuit Replace the fan motor fo
14. C lower than the chamber set temperature E Initial setting factory setting 5 C lower than the chamber set temperature Example Change the alarm temperature to chamber set temperature minus 3 C from chamber set temperature minus 5 C Details Change from the setting that the low temperature alarm works at 5 C lower than the chamber set temperature to the setting that the low temperature alarm works at 3 C lower than the chamber set temperature Following is an example Operate the key according to the desired alarm temperature 1 Depress the temperature display changeover key to light the indicator for refrigerator temperature The current refrigerator temperature 1s displayed on the temperature display 2 Depress the up arrow key for 5 seconds The current chamber temperature on the temperature display changes NE con LI LI i ZIN to function code F00 and the first figure 0 blinks First figure is changeable 3 Depress the up arrow key twice FA as The display changes to F02 from FOO Ah rue Sn 2 ZIN The figure changes between 0 and 9 by depressing the up arrow key Change of first figure 4 Depress the set key once The current setting 05 is displayed and the first figure 5 blinks FT mes tering CO yet and eS bh GT lt gt The initial setting 05 low temperature alarm works when the chamber od Lua FTN temperature is 5C lower than the chamber
15. Panasonic INSTRUCTION MANUAL M P R 71 5 F Pharmaceutical Refrigerator with Freezer 2 Foreword Read this manual carefully before using the appliance and follow the instructions for safety operation Handling of Instruction Manual and Installation Manual E Sanyo never guarantee any safety if the appliance is used for any objects other than intended use or used by any procedures other than those mentioned in this manual E Keep this manual in an adequate place with the enclosed Installation Manual to refer to it as necessary EH Contact a Sanyo sales representative or agent if any page of the manual is lost or page order is incorrect E Contact a Sanyo sales representative or agent if any point in this manual is unclear or if there are any inaccuracies lt gt This manual is only for the pharmaceutical refrigerator with freezer MPR 715F made by Sanyo The contents are subject to change without notice No part of this manual may be reproduced in any form without the expressed written permission of Sanyo Proposal for safe storage of freezer contents This freezer can store the medical or biological material in the low temperature environment We can offer some precautions below to protect the valuable material against accidental temperature rise Contact a Sanyo sales representative or agent for the details or installation Temperature recorder Option Remote alarm system Marketed product 33
16. Ry a The figure changes between 0 and 9 by depressing the up arrow key Change of first figure 6 Depress the scroll key once The second figure starts to blink lt gt The first figure or second figure blinks alternately by depressing the scroll key 7 Depress the up arrow key once The display changes to 005 from 015 Sn PIN The figure changes between 0 and 1 by depressing the up arrow key Change of second figure 8 Depress the set key once The work temperature of high temperature alarm is memorized and Gr the current chamber temperature is displayed on the temperature display Enter of the setting lt gt The setting mode returns to the temperature display mode automatically when 90 seconds has passed without any key operation auto return function In this case the setting is not accepted Important Never input any function code other than the specified one 23 58 Setting of low temperature alarm freezer The abnormality chamber temperature drop 1s noticed by blinking of alarm indicator and chamber temperature display and sounding of the buzzer 15 minutes after blinking if the chamber temperature exceeds the set value of low temperature alarm Always set the low temperature alarm to protect the storage items from damage resulting from temperature drop E Setting range of work temperature for low temperature alarm Between 5 C and 15 C lower than the chamber set temperat
17. Shelf support 9 Air exhaust vent Access port back CECE 4 Bottom shelf Key hole EEE Key hole 0 ee Access port back 1 ml 7 Freezer door A SS M fa 4 Bottom shelf Drain port I MIM oa JAS ew LL SGSs 3S a Space for Drain hose cap temperature recorder Caster bottom 4 locations Location for freezer shelf spacer lt gt Set the enclosed freezer shelf spacer here to prevent the storage items from falling down Spacer serves as a fixture 43 _ Outer and chamber Control panel door front upper The chamber temperature and other alarms functions can be set through the keys on the control panel The running status can be checked by the temperature display and indicators page 10 and 11 2 Shelf support These are used to support the shelves Always set the shelves on the shelf supports firmly lt gt The shelves should be set with the stand edge backside Access port refrigerator and freezer chamber These ports are used to pass the sensor or cable of measuring equipment or sensor of automatic temperature recorder option to the chamber Always replace the rubber caps and the insulation to the access port when no use or the rise of chamber temperature or condensation outside the access port may be resulted Bottom shelf 1 for refrigerator 2 for freezer To protect the storage items always set the bottom shelf on the chamber botto
18. Stop of operation at maintenance eee EET sers eseesseeeeese essences essences EEE EEE TEESE EEE Ee EEE EES 31 Cleaning exterior Interior and accessories err TEETER EERE een en EERE EEE EEE EE EE EEE EEE EES 32 Checking power supply cord MRC EEE EEE RR 32 Checking temperature recorder option a E ABA TR RIS TTR Nano ane 32 34 Table of contents Replacement of wear out parts E 33 Replacing the battery for power failure alarm esse 33 Replacing the fan motor for cooling Circuit EE EEE EE EEE e eee e tenet e ence RR 33 Important aspects when disposing of Unit RRR 34 Decontamination Of Chamber ses 34 Refri gerant RE ANS TER dia CRE RER CRE RER ee ad 34 Temperature recorder option ina eee MRI E NT E 39 Battery for power failure alarm option Lisi ine TE DR een RE MR A RE RR SKR 39 Data acquisition system option er ee eT re eer ee er Oe ee ee ee ee ee re re ee 40 Interface board option ee q Tr eT ee eT Te Te ee TT ie Tre Es ap dna fa BEN el RS DS ES 40 Specifications raia 41 Structural specifications PEPPERS REPARE ER RNP RP BG NRK NN NR NR RR RR ABB E ened 41 Functional specifications RT TICO PRP PT ICE PRE PIT RIC PP TP PR dbs tees deen nes eetewkaneens 42 Performance specifications sia iain tina iene E Da dd da a See RRA SR REN a Ae abies ahaa eee ea E 43 Safety check sheet for copy Pee eee eT eT ee err rT TTC rr Cr cr rer rrr rer Tye 43 35 PRECAUTIONS FOR SAFE OPERATION It is imperative that the user complies with
19. and dispose of The guidelines below for handling and disposing of this unit must be followed without fail It is prohibited to release hydro fluorocarbons also known as Freon to the atmosphere This unit uses hydro fluorocarbons as refrigerant When it is to be disposed of these hydro fluorocarbons must be recovered It is prohibited to release hydro fluorocarbons to the atmosphere without due cause Refer to the rating label for details of the kind of hydro fluorocarbons used and the quantity sealed inside the unit Have a registered contractor recover the hydro fluorocarbons In recovering the hydro fluorocarbons please cooperate with the policies established by the national and regional authorities Recycle and recover the resources of the nickel hydride battery battery for power failure alarm A battery for power failure alarm optional component can be installed in this unit to trigger the power failure alarm The battery should be recycled and recovered in accordance with the applicable regulations Decontamination of chamber Before disposal of pharmaceutical refrigerator with freezer decontaminate the refrigerator and freezer chamber yourself Refrigerant EC Regulation No 842 2006 on Certain Fluorinated Greenhouse Gases DO NOT VENT R 134a INTO THE ATMOSPHERE R 134a IS A FLUORINATED GREENHOUSE GAS COVERED BY THE KYOTO PROTOCOL WITH A GLOBAL WARMING POTENTIAL GWP 1430 34 69 Note This sy
20. arge are used for attachment of temperature recorder MTR 0621LH option or MTR 4015LH option Keep them for future use The clip small are used for attachment of temperature recorder MTR G3504 option Keep them for future use lt gt The installation manual is for service personnel only Never perform the procedure mentioned in the installation manual 12 47 START UP PROCEDURE To commence the operation initially or after temporary power off due to the cleaning maintenance etc follow the procedure below The operation is resumed automatically at the recovery from power failure with the setting before power failure page 15 Prior to power on 1 Check the power switch is OFF 2 Check that the power switch of battery kit for power failure alarm option is OFF if the battery kit for power failure alarm is installed 3 Connect the power supply cord to the dedicated power source with the chamber empty Power on and 4 Turn on the power switch chamber temp D At the power on the high temp alarm is activated The alarm indicator blinks setting and the blinking refrigerator temperature is displayed At the start up with the factory setting the high temp alarm is activated when the refrigerator temperature is higher than 10 C therefore the high temp alarm works High temp alarm chamber temp blinks alarm indicator blinks buzzer sounds after 15 minutes 5 Set the desired chamber refr
21. back wall to keep the cooling performance Also this spacer is used as a fixture Fix the product firmly by using a rope or chain Switch area upper left side Remove the cover when using the power switch or remote alarm terminal lt gt After using always replace the cover Power switch also functions as a circuit breaker This is a power switch of the product ON OFF 0 DRemote alarm terminal A remote alarm device marketed product can be connected to this terminal The alarm is noticed to an operator in the remote area by the remote alarm when the product is installed in an unmanned location Contact a Sanyo sales representative or agent for the installation _ 44 _ Control panel Details of control panel The control panel is comprised of temperature display indicators and keys Indicators O Indication on the temperature display At normal display of current chamber temperature At temperature alarm O blink of chamber temperature DOOR ALARM At alarm by self diagnostic display of code page 29 Indicators Alarm indicator ALARM Blinking of red LED lamp High temp alarm low temp alarm or 0 C alarm refrigerator only page 28 o O REFRIGERATOR ALARM O FREEZER Door alarm indicator DOOR Lighting of red LED lamp The refrigerator or freezer door is open The buzzer sounds 2 minutes initial setting after lighting of door alarm indicator to inform the do
22. chamber set temp t emperature Refrigerator o between 5 C and 15 C RO COMER ans lower than the chamber set chamber set temp t emperature Buzzer suspended 10 20 30 40 50 60 min pos period or no recovery Lock of chamber The enter of function code through the up arrow key and scroll key is needed to set the alarm temperature recovery time delay time For the procedure see the reference page Freezer Important Never enter the function code other than specified one at the time of setting The other function code is for service personnel only 14 49 _ DURING AFTER POWER FAILURE Important It is recommended the battery for power failure alarm option is installed to notice the alarm blink of alarm indicator buzzer in the event of power failure Display of chamber temperature during power failure By depressing the buzzer stop key BUZZER during power failure alarm the buzzer stops and the chamber temperature is displayed on the temperature display for 5 seconds lt gt The buzzer stops however the alarm indicator ALARM keeps to blink The chamber temperature is displayed on the temperature display for 5 seconds by depressing the buzzer stop key BUZZER in spite of power failure Important The battery for power failure alarm is a consumable part Replace the battery every 3 years The alarm would not be activated at power failure if the battery is not replaced regularly Contac
23. d Between 10 and 60 minutes with 10 minutes interval display of setting between 010 and 060 or no recovery display of setting 000 Always set the buzzer suspended period to avoid the wrong recognition of alarm status E Initial setting factory setting 30 minutes display of setting 030 lt gt The buzzer does not recover when the setting is 000 The setting should be between 010 and 060 to ensure the safety of storage items Example setting Following is an example Change the setting of buzzer suspended period to 20 minutes from 30 minutes initial Operate the key according to the desired buzzer suspended period 1 Depress the up arrow key for 5 seconds En ral The current chamber temperature on the temperature display changes yu LJ to function code FOO and the first figure 0 blinks First figure is changeable 2 Depress the up arrow key 5 times The display changes to F05 from FOO The figure changes between 0 and 9 by depressing the up arrow key 3 Depress the scroll key once TN Cy UNE N 7 Change of first figure NIZ The second figure starts to blink r 3 6 7 RT pea Us ee ee TN ES DS E RR AD DD PAN The first figure or second figure blinks alternately by depressing the scroll key 4 Depress the up arrow key twice The display changes to F25 from FOS The figure changes between 0 and 5 by depressing the up arrow key 5 Depress the set key once Second
24. de apparatuur bij de lokaal erkende instanties gaat gebeuren In de Europese Unie wordt de gebruikte elektrische en elektronische apparatuur bij de daarvoor wettelijke instanties aangeboden Alstublieft help allen mee om het milieu te beschermen Swedish Din SANYO produkt ar designad och tillverkad av material och komponenter med hog kvalitet som kan atervinnas och ateranvandas Denna symbol betyder att elektriska och elektroniska produkter efter slutanvandande skall sorteras och l mnas separat fran Ditt hush llsavfall V nligen l mna denna produkt hos Din lokala mottagningstation f r avfall tervinningsstation Inom den Europeiska Unionen finns det separata tervinningssystem f r begagnade elektriska och elektroniska produkter V nligen hj lp oss att bevara milj n vi lever i 38 73 TEMPERATURE RECORDER OPTION The chamber temperature can be recorded and checked by installing an optional temperature recorder MTR G3504 MTR 0621LH or MTR 4015LH lt gt Contact a Sanyo sales representative or agent for the purchase of temperature recorder Main specifications of temperature recorder MTR G3504 MTR 0621LH MTR 4015LH Application Refrigerator amp Freezer Recording range 60 40 C 10 40 C 6 20 C 40 14 C 3 1 days batch Feed d of eed speed O 7 day 1 turn 32 day 1 turn 3 1 days batch recorder chart Circular type Strip type Strip type Supplied from the refrigerator Dry cell Dry c
25. e of more than 15 A and rated voltage L The power switch is OFF The alarm is operative alarm indicator blinks buzzer sounds at start up The alarm blinking of alarm indicator sound of buzzer is continued until the chamber temperature reaches the chamber set temperature The alarm is operative alarm indicator blinks buzzer sounds during operation O The capacity or voltage of the power source is not sufficient Use a dedicated power source of more than 15 A and rated voltage L The side or back of the unit contacts with the nearby wall 26 61 The cooling is poor C The ambient temperature is high The usable ambient temperature is between 5 and 30 C L The access port is not covered Cover the access port with thermal insulation and rubber caps when no use O The magnetic door gasket is damaged Contact Sanyo sales representative or agent for the replacement of the magnetic door gasket if it is damaged CO The unit is installed near an electric appliance emitting the radio wave The setting of chamber temperature key input is ineffective L The lock of chamber temperature setting is ON Change the lock to OFF page 17 The setting mode returns to the temperature display mode lt gt The setting mode returns to the temperature display mode automatically when 90 seconds has passed without any key operation auto return function Note Never install an electric appliance emittin
26. ell lt gt For the installation of temperature recorder MTR G3504 optional recorder mounting bracket MPR S7 is necessary lt gt For the installation of temperature recorder MTR 0621LH or MTR 4115LH optional recorder mounting bracket MPR S30 is necessary BATTERY FOR POWER FAILURE ALARM OPTION It is recommended to install an optional battery for power failure alarm MPR 48B to prevent the rise of chamber temperature in the case of power failure At the power failure the alarm activates blink of alarm indicator sound of buzzer to prompt an action for preventing the storage items lt gt Contact a Sanyo sales representative or agent for the purchase of battery for power failure alarm 39 74 DATA ACQUISITION SYSTEM OPTION By using the optional data acquisition system MTR 5000 the data from Sanyo medical equipment can be acquired and maintained with a personal computer through an optional interface board MTR 480 or LAN interface board MTR L03 The data acquisition system MTR 5000 is not applicable to some of Sanyo medical equipment In addition auto mailing function sends an e mail to a specified mail address when any abnormality is detected in the running status of equipment This reduces the risk of damage of storage items lt gt Contact a Sanyo sales representative or agent for the purchase of data acquisition system INTERFACE BOARD OPTION The temperature log of Sanyo medical equi
27. ent temperature alarm At the same time transfer the storage items to another refrigerator or freezer Low temp alarm Blink of refrigerator temperature indication and alarm indicator Intermittent tone of buzzer remote alarm linked gt If the alarm fails to stop even after one hour or if 0 C alarm the chamber temperature fails to rise contact a i The refrigerator temperature is Refrigerator 0 C or below Sanyo sales representative or agent only gt At the same time transfer the storage items to another refrigerator Blink of alarm indicator Intermittent tone of buzzer remote alarm linked when the MPR 48B optional component is installed Cause Action Sont ailur hasdccuned gt If the power outage is zm s to last for a long Power time use dry ice etc to protect the storage items failure he power supply cord is alarm e or the power switch is OFF The alarm for power failure blink of alarm indicator intermittent tone of buzzer does not activate without MPR 48B optional component Check the power supply cord and the power switch Light of door alarm indicator Intermittent tone of buzzer two minutes after the door alarm indicator has lighted default setting Check whether the refrigerator door and freezer The refrigerator door or freezer door are closed door is open D Check whether foreign matter is sandwiched in the magnetic door gaskets
28. erature is lit OFF is not displayed 3 When the defrost is disappeared remove the drain hose cap to take out the drain hose Set a pan under the drain hose Drain hose Remove the drain hose cap and drain port cap in the freezer to drain the water 4 Wipe off the freezer with a dry cloth Replace the caps to the drain hose and store the drain hose Then replace the cap to the drain port 1n the freezer 5 Start the freezer operation according to the procedure on page 19 6 Check that the freezer temperature reaches the set temperature and replace the storage items 20 55 SETTING OF ALARM TEMPERATURE The abnormality chamber temperature rise is noticed by blinking of alarm indicator and chamber temperature display and sounding of the buzzer 15 minutes after blinking if the chamber temperature exceeds the set value of high temperature alarm Always set the high temperature alarm to protect the storage items from damage resulting from temperature rise E Setting range of work temperature for high temperature alarm Between 2 C and 14 C higher than the chamber set temperature E Initial setting factory setting 5 C higher than the chamber set temperature Example Change the alarm temperature to chamber set temperature plus 3 C from chamber set temperature plus 5 C Details Change from the setting that the high temperature alarm works at 5 C higher than the chamber set temperature to the
29. ervar el medio ambiente 36 71 Portuguese O seu produto SANYO foi concebido e produzido com materiais e componentes de alta qualidade que podem ser reciclados e reutilizados Este s mbolo significa que o equipamento el ctrico e electr nico no final da sua vida til dever ser descartado separadamente do seu lixo dom stico Por favor entregue este equipamento no seu ponto local de recolha reciclagem Na Uni o Europeia existem sistemas de recolha separados para produtos el ctricos e electr nicos usados Por favor ajude nos a conservar o ambiente em que vivemos Italian II vostro prodotto SANYO stato costruito da materiali e componenti di alta qualita che sono riutilizzabili o riciclabili Prodotti elettrici ed elettronici portando questo simbolo alla fine delluso devono essere smaltiti separatamente dai rifiuti casalinghi Vi preghiamo di smaltire questo apparecchio al deposito comunale Nell Unione Europea esistono sistemi di raccolta differenziata per prodotti elettrici ed elettronici Aiutateci a conservare l ambiente in cui viviamo 3 7 Dutch Sanyo producten zijn ontwikkeld en gefabriceerd uit eerste kwaliteit materialen de onderdelen kunnen worden gerecycled en weer worden gebruikt Het symbool betekent dat de elektrische en elektronische onderdelen wanneer deze vernietigd gaan worden dit separaat gebeurt van het normale huisafval Zorg ervoor dat het verwijderen van
30. f key 2 large clips and 4 small clips for temperature recorder including accessories 2 freezer shelf spacers Instruction manual Installation manual Temperature recorder for refrigerator amp freezer MTR G3504 Temperature recorder for refrigerator MTR 0621LH Temperature recorder for freezer MTR 4015LH Recorder mounting bracket MPR S7 for MTR G3504 Recorder mounting bracket MPR S30 for MTR 0621LH MTR 4015 Recorder chart for MTR G3504 RP G3504 Recorder chart for MTR 0621LH RP 06 Recorder chart for MTR 4015LH RP 40 Recorder pen for MTR G3504 PG RB Battery for power failure alarm MPR 48B Container for freezer 2 pcs MPR 715SC Data acquisition system MTR 5000 Interface board MTR 480 LAN interface board MTR LO3 lt gt Specifications will be subject to change without notice Optional components 41 70 Functional specifications Model Temperature controller Temperature display Thermal sensor Alarm temperature Chamber set temperature 5 15 C freezer Buzzer suspended period Door alarm Lock of chamber set temperature ON or OFF High temperature alarm Low temperature alarm Door alarm Alarms 0 C alarm refrigerator only Power failure alarm with MPR 48B installed Sensor abnormality Abnormal temp of cooling circuit Fan motor life Battery life with MPR 48B installed Remote alarm terminal Allowable contact capacity 30 VDC 2A Back up of setting Nonvolatile memory
31. fy the unit or optional components yourself gt Any such work carried out by an unauthorized person may result in fire or electric shock or injury due to a malfunction Disconnect the power supply plug if there is something wrong with the unit gt Continued abnormal operation may cause electric shock or fire When removing the power supply plug from the power supply outlet grip the power supply plug not the cord gt Pulling the cord may result in electric shock or fire by short circuit Disconnect the power supply plug when the unit is not used for long periods gt Keeping the connection may cause electric shock current leakage or fire due to the deterioration of insulation If the unit is to be stored unused in an unsupervised area for an extended period ensure that children do not have access and that doors cannot be closed completely gt Removing doors prevents accidents such as suffocation The disposal of the unit should be accomplished by appropriate personnel gt Leaving the unit in an unsupervised area may cause accidents Do not put the packing plastic bag within reach of children gt Leaving the packing plastic bag may cause accidents such as suffocation 30 CAUTION Power supply re start moving service call This unit must be plugged into a dedicated circuit protected by branch circuit breaker Use a dedicated power source as indicated on the rating label attached to the unit
32. g the radio wave near the unit The unit may malfunction by the noise resulting from the radio wave 27 02 ACTION FOR ALARM When an alarm has been generated check the cause on the basis of the type of alarm generated and take the necessary action to deal with 1t without delay Refer to the next page for the alarm with error code indication E01 to E12 or F2 on the temperature display lt gt Contact a Sanyo sales representative or agent if the alarm is not released by eliminating the following cause Before calling for service take some precautions for the storage items placing of dry ice wrapped in newspaper in the chamber or transferring the storage items to another freezer Blink of chamber temperature indication and alarm indicator Intermittent tone of buzzer after 15 minutes remote alarm linked gt Ifthe alarm fails to stop even after one hour or if the chamber temperature fails to drop contact a The chamber temperature 1s Sanyo sales representative or agent higher than the setting of high At the same time transfer the storage items to temperature alarm another refrigerator or freezer If no other refrigerator or freezer is available use dry ice etc to protect the storage items High temp alarm If the alarm fails to stop even after one hour or if The chamber temperature is the chamber temperature fails to rise contact a lower than the setting of low Sanyo sales representative or ag
33. he rating label may cause fire or electric shock Never store volatile or flammable substances in this unit if the container cannot be sealed gt These may cause explosion or fire Do not insert metal objects such as a pin or a wire into any vent gap or any outlet on the unit gt This may cause electric shock or injury by accidental contact with moving parts Use this unit in safe area when treating the poison harmful or radiate articles gt Improper use may cause bad effect on your health or environment Turn off the power switch and disconnect the power supply to the unit prior to any maintenance of the unit gt Failure to follow this may cause electric shock or injury Do not touch any electrical parts such as power supply plug or operate switches with a wet hand gt This may cause electric shock 3 OO 9 MODO OOS Ensure you do not inhale or consume medication or aerosols from around the unit at the time of maintenance gt These may be harmful to your health Never splash water directly onto the unit Never put containers with liquid on the unit gt Water or liquid may cause electric shock or short circuit Never bind process or step on the power supply cord or never damage or break the power supply plug Do not use the power supply cord if there is something wrong with it gt A broken power supply cord or plug may cause fire or electric shock Never disassemble repair or modi
34. ich needs severe temperature control is stored 13 48 HANDLING OF STORAGE ITEMS Always follow the indication below when taking out putting in the material E Put on the gloves when taking out putting in the storage items in the freezer chamber No gloves may cause injury E Do not put the excessive storage items in the chamber Over putting disturbs the cold air circulation and degrades the cooling performance E Open close the doors quickly or the chamber temperature rises E Do not put a large amount of storage items of high temperature at a time M Put the storage items close to the shelf center to avoid the contact with the chamber wall Keep an adequate space between materials Contacting with chamber wall or other materials causes uneven cooling in the chamber INITIALSETTING SETTING RANGE FUNCTION CODE Following shows the initial setting factory setting and setting range of each item Change the setting as needed Refer to the each related page for the details and procedure of the setting See Function Reference Setting item Initial setting Setting range figure Refrigerator temp 214 C 35 15 C High temp alarm higher than the chamber set chamber set temp temperature Refrigerator of L between 5 C and 15 C eee ME higher than the chamber set chamber set temp t emperature Freezer Low temp alarm l eer eee re between 2 C and 14 C lower than the chamber set
35. igerator and freezer temperature page 16 The factory setting of refrigerator temperature is 5 C and the freezer temperature is 30 C Important Allow 5 minutes before turn on the power switch when the power switch is off That is a time for compressor to start up again It takes about 2 5 hours to reach the set temperature ambient temp 30 C no load without containers Waiting amp check 6 On the temp display check the chamber temp reaches the set temperature Power on of 7 Turn on the power switch of battery kit for power failure alarm option if the battery kit for power failure alarm battery kit for power failure alarm is installed Operation check 8 By opening the refrigerator door check the chamber lamp is on Storage of material 9 Put the material in the chamber gradually page 14 Putting a large amount of material in the chamber at a time causes the temperature rise Never block the air intake vent or air exhaust vent in the refrigerator Setting 10 As needed set the alarm temp page 21 to 24 buzzer suspended period page 25 and the lock of chamber temperature setting page 17 Attention The condensation may be found on the glass of refrigerator door under high temperature and humidity condition Wipe off the condensation with a soft dry cloth NCAUTION It is recommended to install a temperature recorder option to check the highest lowest chamber temperature when the item wh
36. ill appear alternately on the temperature display page 33 lt gt The alarm functions will not work when the battery charge is depleted Contact a Sanyo sales representative or agent to replace the battery lt gt The replacement of the battery for power failure alarm is a paid service Installing a remote alarm system When the product is installed in an unmanned location lt gt Connect a remote alarm device sold on the market to the remote alarm terminals of the product and install a remote alarm system to alert the administrator in charge Contact a Sanyo sales representative or agent to install the system Replacing the fan motor for cooling circuit Replacement frequency Every six years the F2 and the chamber temperature display will appear alternately on the temperature display page 33 When the fan motor for cooling circuit deteriorates the cooling capability is reduced and the chamber temperature may rise Contact a Sanyo sales representative or agent to replace the fan motor for cooling circuit lt gt The replacement of the fan motor for cooling circuit is a paid service 4 Action for chamber temperature rise When the high temperature alarm or power failure alarm when the battery for power failure alarm battery is installed has been activated in which case the alarm indicator blinks and the buzzer sounds as a result of an unforeseen event take the action described below without delay
37. ing on the mains supply m Applicable pollution degree of the intended environment pollution degree 2 in most cases 40 PRECAUTIONS AND ACTION FOR TEMP RISE Precautions for temperature rise As a preventive measure take the following steps to protect the valuable storage items in the chamber in case the unit should stop operating as a result of unforeseen events such as a power failure and its chamber temperature should rise Important SANYO guarantees the product under certain warranty conditions SANYO in no way shall be responsible for any loss of content or damage of content Dividing the storage items up between a multiple number of freezers As a preventive measure divide up valuable storage items and store them in a multiple number of freezers in case an unforeseen event should occur Conducting periodic maintenance and inspection in accordance with a maintenance system contract required lt gt For details on the maintenance system consult a Sanyo sales representative or agent Installing a battery for power failure alarm optional component and preparing to take action to deal with emergencies Install a battery for power failure alarm and also make preparations to deal with emergencies should the product stop operating as a result of an unforeseen event Replacing the battery for power failure alarm Replacement frequency Every three years the F1 and the chamber temperature display w
38. is displayed on the temperature display and SET E D 5 PIN the second figure 0 blinks i Depress the scroll key once The first figure starts to blink 1 Sad CS CS um N gt lt The first figure or second figure blinks alternately by depressing the scroll First figure is changeable key 4 Depress the up arrow key 9 times needed times for change AP yy The display changes to 004 from 005 wy Wi The figure changes between 0 and 9 by depressing the up arrow key Change of first figure 5 Depress the set key once SET i i G The refrigerator temperature is memorized and the current refrigerator SJ temperature is displayed on the temperature display Enter of the setting 6 Depress the temperature display changeover key once The indicator for freezer temperature lights and the current freezer 3 D temperature is displayed on the temperature display E 7 Depress the set key Em 5 The current setting 30 is displayed on the temperature display and JU E PIN the second figure 3 blinks Second figure is changeable 8 Depress the up arrow key 3 times needed times for change 5 The display changes to 30 from 20 E LI lt gt The figure changes between 0 and 3 by depressing the up arrow key Change of second figure 9 Depress the scroll key once The first figure starts to blink lt gt The first figure or second figure blinks alternately by depressing the
39. l in this form before servicing Hand over this form to the service engineer to keep for his and your safety Please decontaminate the unit yourself before calling the service engineer 43 18 DC4188 30B Printed in Japan
40. m 5 Space for temperature recorder A temperature recorder option is mounted here and the chamber temperature can be recorded automatically page 39 Contact a Sanyo sales representative or agent for the installation G Leveling foot bottom 4 locations This is the bolt for setting the product and adjusting the level on the right and the left At the installation extend the bolt until the front casters are away from the floor to set the product Drain hose cap This is used to drain the defrost water in the freezer chamber at the time of defrosting The drain hose is accessible by removing the drain hose cap page 20 lt gt Always replace the drain hose cap after draining 8 Drain port This port is used to drain the defrost water in the freezer chamber lt gt Always replace the port cap after draining Air exhaust vent This is an air exhaust vent to circulating the air in the refrigerator chamber Do not block this vent Blocking this vent may cause unstable chamber temperature Arrange the storage items not to be subjected to the cold air from this vent to avoid freezing DAir intake vent This is an air intake vent to circulating the air in the refrigerator chamber Do not block this vent Blocking this vent may cause unstable chamber temperature Do not insert fingers or similar articles into this vent Back spacer also used as a fixture This spacer keeps the space between the back and the
41. mbol mark and recycle system are applied only to EU countries and not applied to the countries in the other area of the world English Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and reused This symbol means that electrical and electronic equipment at their end of life should be disposed of separately from your household waste Please dispose of this equipment at your local community waste collection recycling centre In the European Union there are separate collection systems for used electrical and electronic products Please help us to conserve the environment we live in German Ihr SANYO Produkt wurde entworfen und hergestellt mit qualitativ hochwertigen Materialien und Komponenten die recycelt und wiederverwendet werden konnen Dieses Symbol bedeutet da elektrische und elektronische Ger te am Ende ihrer Nutzungsdauer von Hausmull getrennt entsorgt werden sollen Bitte entsorgen Sie dieses Gerat bei Ihrer Grtlichen kommunalen Sammelstelle oder im Recycling Centre In der Europ ischen Union gibt es unterschiedliche Sammelsysteme fur Elektrik und Elektronikgerate Helfen Sie uns bitte die Umwelt zu erhalten in der wir leben 35 70 French Votre produit Sanyo est con u et fabriqu avec des materiels et des composants de qualit sup rieure qui peuvent tre recycles et r utilis s Ce symbole signifie que les quipements
42. nges to 05 from 25 vs US The figure changes between 0 and 3 by depressing the up arrow key Change of second figure 4 Depress the scroll key once no The first figure starts to blink 05 lt gt The first figure or second figure blinks alternately by depressing the scroll A an key First figure is changeable ASPA tm Li LI FIX Change of first fiqure 5 Depress the up arrow key 5 times The display changes to 00 from 05 The figure changes between 0 and 9 by depressing the up arrow key 6 Depress the set key once M The freezer operation stops and the current freezer temperature and ad OFF is alternately displayed on the temperature display Stop of freezer operation The setting mode returns to the temperature display mode automatically when 90 seconds has passed without any key operation auto return function In this case the setting is not accepted 18 53 STOP OF FREEZER OPERATION Procedure to resume the freezer operation The following shows the procedure to resume the freezer operation resumed by setting the freezer temperature Example Resume the freezer operation with 25 C setting Following is an example Change the set temperature as needed 1 Depress the temperature display changeover key to light the indicator for freezer temperature The current freezer temperature and OFF is displayed alternately on the temperature display 2 Depress the set key
43. nt leakage or electric shock may result if the unit is exposed to rain water Only qualified engineers or service personnel should install the unit gt The installation by unqualified personnel may cause electric shock or fire Install the unit on a sturdy floor and take an adequate precaution to prevent the unit from turning over gt If the floor is not strong enough or the installation site is not adequate this may result in injury from the unit falling or tipping over Never install the unit in a humid place or a place where it is likely to be splashed by water gt Deterioration of the insulation may result which could cause current leakage or electric shock Never install the unit in a flammable or volatile location gt This may cause explosion or fire Never install the unit where acid or corrosive gases are present gt The current leakage or electric shock may result due to corrosion Always ground earth the unit to prevent electric shock If the power supply outlet is not grounded it will be necessary to install a ground by qualified engineers gt No earth may cause electric shock Never ground the unit through a gas pipe water main telephone line or lightning rod gt Inadequate grounding may cause electric shock in the case of an incomplete circuit Connect the unit to a power source as indicated on the rating label attached to the unit gt Use of any other voltage or frequency other than that on t
44. of the setting The setting mode returns to the temperature display mode automatically when 90 seconds has passed without any key operation auto return function In this case the setting is not accepted Important Never input any function code other than the specified one Important The alarm may be activated after defrosting or when too much items are stored in the refrigerator depending on the setting of high temperature alarm This is not a malfunction The alarm is cancelled automatically when the refrigerator temperature reaches the set temperature 21 0 Setting of low temperature alarm refrigerator The abnormality chamber temperature drop 1s noticed by blinking of alarm indicator and chamber temperature display and sounding of the buzzer 15 minutes after blinking if the chamber temperature exceeds the set value of low temperature alarm Always set the low temperature alarm to protect the storage items from damage resulting from temperature drop Important The abnormal temperature descent is notified by the blink of alarm indicator and display of refrigerator temperature and the buzzer when the refrigerator temperature is 0 C or lower with regardless the setting of low temperature alarm In this case the remote alarm terminal is changed to alarm status This is a precaution against the freezing of storage items E Setting range of work temperature for low temperature alarm Between 2 C and 14
45. om LO fl lt gt The figure changes between 0 and 1 by depressing the up arrow key Change of lock stalle 3 Depress the set key The setting of lock is ON and the current chamber temperature is AS displayed on the temperature display a sacana lt gt The setting mode returns to the temperature display mode automatically when 90 seconds has passed without any key operation auto return function In this case the setting is not accepted 17 OM STOP OF FREEZER OPERATION Procedure to stop the freezer operation The freezer operation can be stopped when removing the frost in the freezer chamber or when no use of freezer The current freezer temperature and OFF is displayed alternately on the temperature display when the indicator for freezer temperature lights The current refrigerator temperature is displayed and OFF is not displayed when the indicator for refrigerator temperature lights Example Stop of freezer operation Following is an example The set temperature of freezer is 25 C 1 Depress the temperature display changeover key to light the indicator for freezer temperature The current freezer temperature is displayed on the temperature _ e 3 display 2 Depress the set key once The current setting 25 is displayed on the temperature display and sf 25 the second figure 2 blinks Second figure is changeable 3 Depress the up arrow key 3 times The display cha
46. once The previous setting 00 is displayed on the temperature display and the second figure 0 blinks 3 Depress the up arrow key twice The display changes to 20 from 00 The figure changes between O and 3 by depressing the up arrow key 4 Depress the scroll key once The first figure starts to blink lt gt The first figure or second figure blinks alternately by depressing the scroll key 5 Depress the up arrow key 5 times The display changes to 25 from 20 The figure changes between 0 and 9 by depressing the up arrow key 6 Depress the set key once The freezer temperature is memorized and the freezer operation starts The current freezer temperature is displayed with blink The freezer operation can be OFF NIPA E Eoi T ny PIN Second figure is changeable NIPA tL wu LJ ZTN Change of second figure NIPA e ZIN First figure is changeable N14 sm L FAR Change of first figure SET Start of freezer operation The setting mode returns to the temperature display mode automatically when 90 seconds has passed without any key operation auto return function 19 54 In this case the setting 1s not accepted DEFROST Defrost in refrigerator The following 2 types of defrosting methods is provided for the refrigerator Both of them are controlled automatically O Cycle defrosting The refrigerator temperature is kept stable b
47. or open page 28 10 45 Temperature display MOO eee me ence cence seen n coesa serenas acetona da FREEZER J LJ TEMPERATURE C Indicator for refrigerator temperature REFRIGERATOR Lighting of green LED lamp This means the refrigerator temperature 1s displayed on the temperature display Indicator for freezer temperature FREEZER Lighting of green LED lamp This means the freezer temperature is displayed Function of each key The buzzer sounds again after 30 minutes initial setting even if the buzzer is stopped by depressing the buzzer stop key BUZZER when the same alarm status continues The alarm indicator blinks and the buzzer sounds when other alarm is occurred in spite of buzzer stop period Buzzer stop key BUZZER The buzzer is silenced by depressing this key when the alarm indicator blinks and the buzzer sounds The remote alarm cannot be canceled Temperature display changeover key REF FREEZ By pressing this key the displayed temperature is changed alternately current refrigerator temperature and current freezer temperature With the changeover of the temperature display the indicator for refrigerator temperature and indicator for freezer temperature lights alternately Set key SET Depress this key to enter the set value during the setting procedure page 16 to 25 Scroll key pb At temperature display mode Depressing this key for more
48. pment can be loaded into a personal computer by using the combination of optional interface board MTR 480 and data acquisition system MTR 5000 For the loading RS 232C is needed to connect Sanyo medical equipment with a personal computer The combination of optional LAN interface board MTR L03 and data acquisition system MTR 5000 enables the equipment monitoring such as chamber temperature by connecting Sanyo medical equipment with the data acquisition system MTR 5000 with LAN The interface board MTR 480 and LAN interface board MTR L03 cannot used at the same time lt gt Contact a Sanyo sales representative or agent for the purchase of interface board 40 75 SPECIFICATIONS Constructional specifications Pharmaceutical refrigerator with freezer MPR 715F External dimensions W900 X D715 X H1910 mm W810 x D615 xX H894 mm refrigerator Internal dimensions W770 X D552 X H422 mm freezer Effective capacity 415 L refrigerator 176 L freezer Styrene resin Refrigerator Colored aluminum Freezer Painted steel 2 doors Refrigerator door Provided with glass window Painted steel 2 doors Refrigerator Inner dimensions W798 x D471 mm Inner dimensions W338 x D527 mm Hermetic Rose type Output 150 W refrigerator Hermetic reciprocating type Output 200 W freezer Fin and tube type refrigerator Tube on sheet type Freezer Side skin condenser frame pipe freezer I set o
49. r cooling circuit every 6 years when F2 and chamber temperature 1s displayed alternately to ensure the alarm is operated in the event of power failure Contact Sanyo sales representative or agent for the replacement of fan motor for cooling circuit when F2 and chamber temperature is displayed alternately lt gt The replacement of the fan motor for cooling circuit is a paid service The appropriate operation of the unit is maintained by cooling the compressor with a fan The motor to operate the fan fan motor for cooling circuit is a wear out part A degraded fan motor for cooling circuit may result in the poor cooling performance Important The alternate display of E10 and chamber temperature with buzzer sound means the failure of fan motor for cooling circuit In this case contact Sanyo sales representative or agent for the replacement of fan motor for cooling circuit immediately 33 68 IMPORTANT ASPECTS WHEN DISPOSING OF UNIT Contact a Sanyo sales representative or agent to dispose of the unit NWARNING The disposal of the unit should be accomplished by appropriate personnel gt Leaving the unit in an unsupervised area may cause accidents Request Prior to disposing of the unit please decontaminate the product yourself as far as possible This pharmaceutical refrigerator with freezer MPR 715F uses refrigerant and battery that the applicable laws and regulations require the user to recover
50. rcuit when the liquid is spilled Checking power supply cord Check the power supply cord once a 6 months by the following procedure with the power supply cord disconnected from the power supply outlet A dusty power supply plug or incomplete insertion of the power supply plug may cause fire Also a damaged power supply cord may cause fire or electric shock 1 Stop the operation by the procedure in Stop of operation at maintenance on page 31 2 Disconnect the power supply plug and remove the dust on the power supply plug with a brush 3 Wipe the power supply cord with a soft dry cloth At the time check the damage on the power supply cord visually 4 Start the operation by the start up procedure on page 13 Checking temperature recorder option Check the following item once a month when the temperature recorder option 1s installed In case of MT R G3504 L The temperature recorder is fixed to the front panel of the refrigerator firmly there is no backlash L The recorder chart is fed turned properly L The green indicator can be recognized through the recorder chart O There is no lack of ink In case of MT R 0621LH or MTR 4015LH L The temperature recorder is fixed to the front panel of the refrigerator firmly there is no backlash O The recorder chart is fed properly and the used recorder chart is folded properly C1 There is no lack of ink Replace the dry cell in the temperature recorder MTR 0
51. ress the up arrow key 5 times as needed for change First figure is changeable NIPA h o The display changes to 15 from 10 5 GS SR CRS O O TT TT siso ei een cena oo 1 PIN lt gt The figure changes between 0 and 9 by depressing the up arrow key Change of first diait 6 Depress the scroll key once ao The second figure starts to blink 13 lt gt The first figure or second figure blinks alternately by depressing the scroll ft nas key Second figure is changeable Te Depress the up arrow key once E FT C The display changes to 05 from 15 SE The figure changes between 0 and 1 by depressing the up arrow key Change of second figure 8 Depress the set key once The work temperature of low temperature alarm is memorized and the NJL current chamber temperature is displayed on the temperature display Enter of the settin The setting mode returns to the temperature display mode automatically when 90 seconds has passed without any key operation auto return function In this case the setting is not accepted Important Never input any function code other than the specified one 24 59 _ SETTING OF BUZZER SUSPENDED PERIOD The abnormality is noticed again by sounding of the buzzer after certain suspended period buzzer recovery timing if the alarm status continues even after the buzzer is silenced by depressing the buzzer stop key BUZZER E Setting range of buzzer suspended perio
52. s returned to the Auto return seconds in the setting mode temperature display mode The change of temperature setting is disable Key lock The key lock is ON L1 30 65 ROUTINE MAINTENANCE Clean or maintain the unit once a month to keep the appropriate performance and safety of the unit WARNING CAUTION Guideline for maintenance Turn off the power switch if provided and disconnect the power supply to the unit prior to any maintenance of the unit gt Failure to follow this may cause electric shock or injury Ensure you do not inhale or consume medication or aerosols from around the unit at the time of maintenance gt These may be harmful to your health Put on the gloves at the time of maintenance gt The edge or corner of the component may cause injury Use a dry cloth to wipe off small amounts of dirt on the outside and inside of the unit and all accessories If the outside panels are dirty clean them with a diluted neutral dishwashing detergent gt Undiluted detergent can damage the plastic components For the dilution refer to the instruction of the detergent Do not clean the unit with scrubbing brushes acid thinner solvents powdered soap cleanser or hot water gt These agents can scratch the paint or cause it to peel Plastic and rubber parts can be easily damaged by these materials Especially never use any volatile solvent to clean the plastic or rubber parts
53. setting that the high temperature alarm works at 3 C higher than the chamber set temperature x Following is an example Operate the key according to the desired alarm temperature 1 Depress the temperature display changeover key to light the indicator for refrigerator temperature l The current refrigerator temperature is displayed on the temperature 4 display 2 Depress the up arrow key for 5 seconds FA ral The current chamber temperature on the temperature display changes Adi yeu Sf to function code F00 and the first figure 0 blinks First fig re is changeable 3 Depress the up arrow key once A FA The display changes to F01 from F00 FU I The figure changes between 0 and 9 by depressing the up arrow key Change of first figure 4 Depress the set key once The current setting 015 is displayed and the first figure 5 blinks The initial setting 005 high temperature alarm works when the chamber k a temperature is 5C higher than the chamber set temperature is displayed at the first setting after installation 5 Depress the up arrow key 8 times as needed for change AT The display changes to 003 from 005 tt The figure changes between 0 and 9 by depressing the up arrow key Change of first figure 6 Depress the set key once The work temperature of high temperature alarm is memorized and Gr 4 the current chamber temperature is displayed on the temperature display Enter
54. t Sanyo sales representative or agent for the replacement of battery Operation check after recovery from the power failure After recovery from the power failure the operation will be resumed automatically with the setting before power failure There is no need to re setting however always check the running status after recovery lt gt The setting before power failure is memorized during power failure by nonvolatile memory NCAUTION At the recovery from the power failure check the unit starts the operation properly Also check there is no change on the setting 15 50 SETTING OF CHAMBER TEMPERATURE Set the chamber temperature as needed to keep the material at appropriate temperature for long period of time E Setting range of chamber temperature Refrigerator between 2 and 14 C Freezer between 35 and 15 C For the temperature control range refer to Performance specifications E Initial setting factory setting Refrigerator 5 C Freezer 30 C Example Change the setting of chamber temperature to 4 C refrigerator and 25 C freezer x Following is an example Operate the key according to the desired chamber temperature 1 Depress the temperature display changeover key to light the indicator for refrigerator temperature E iy 5 The current refrigerator temperature is displayed on the temperature display 2 Depress the set key once NP The current setting 005
55. than 5 seconds leads the setting of lock of chamber temperature setting page 17 At setting mode Depressing this key leads the movement between the digit to be inputted blinked digit on the temperature display page 16 to 25 Up arrow key At temperature display mode Temp display mode the status that the Depressing this key for more than 5 seconds leads the setting mode current chamber temp is displayed on the At setting mode temp display By depressing this key the figure to be inputted blinked digit on Setting mode the status that the input on the temperature display can be changed page 16 to 25 the temp display is effective by depressing At the setting of lock of chamber temperature setting the up arrow key for more than 5 seconds By depressing this key ON OFF of the lock can be selected page 17 11 46 CHECK OF ENCLOSURES Before commencing the operation check the accessories and printed matters enclosed with the refrigerator Contact a Sanyo sales representative or agent if anything is missed Key 2 keys Clip large Clip small Freezer shelf spacer Ckthisone Instruction manual gt this one Installation manual EC Regulation No 842 2006 on Certain F r birosemodetodi Fluorinated Greenhouse Gases P y Waste Electrical and Electronic Equipment For Eurove model onl WEEE Directive 2002 96 EC E 7 lt gt The clip l
56. this manual as it contains important safety advice Items and procedures are described so that you can use this unit correctly and safely If the precautions advised are followed this will prevent possible injury to the user and any other person Symbols for warning and caution The warning and caution regarding to the safety 1s indicated with the following indications and symbols in this manual and on the product Always check and follow the indications Degree and indication of risk damage Precautions are illustrated in the following way Never fail to follow the instructions since both precautions are important item regarding to the safety Failure to observe WARNING signs could result in a hazard to NWARN N G personnel possibly resulting in serious injury or death Failure to observe CAUTION signs could result in injury to A CAUTION personnel and damage to the unit and associated property Symbol shows A This symbol means caution This symbol means an action is prohibited This symbol means an instruction must be followed Warning for electric shock label on the product This mark is labeled on the cover in which the electrical components of high voltage are enclosed to prevent the electric shock no Never remove the cover 20 Warning and caution for handling the unit WARNING Installation Use Stop Aki K A DO OU OOO Do not use the unit outdoors gt Curre
57. to protect the storage item Checking the causes and taking the necessary action Important Check the cause of the temperature rise and take action without delay to deal with the cause I Action for alarm page 281 MH If the alarm fails to stop or the chamber temperature fails to drop even after one hour a machine malfunction may have occurred Contact a Sanyo sales representative or agent without delay M Transfer the storage items to another refrigerator and freezer Action when the product has stopped due to a power failure If a power failure is responsible for the rise m temperature check when the power will likely be restored and take the appropriate action for the duration concerned Action to when the power failure is of short duration several minutes to up to one hour EH Do not open the doors as this will cause the chamber temperature to rise EH Reduce the ambient temperature to 25 C or below Action to take when the power outage is of long duration one hour or more M Transfer the storage items to another refrigerator and freezer EH Provide a back up power source if no other refrigerator and freezer are available 42 REFRIGERATOR COMPONENTS Main body The function of components with number is described on the next page DRemote alarm terminal inside Lamp Control panel Refrigerator door Magnetic door es gasket Air intak t Ir intake ven 2
58. ure E Initial setting factory setting 10 C lower than the chamber set temperature Example Change the alarm temperature to chamber set temperature minus 5 C from chamber set temperature minus 10 C Details Change from the setting that the low temperature alarm works at 10 C lower than the chamber set temperature to the setting that the low temperature alarm works at 5 C lower than the chamber set temperature x Following is an example Operate the key according to the desired alarm temperature 1 Depress the temperature display changeover key to light the indicator for freezer temperature JC The current freezer temperature is displayed on the temperature J display 2 Depress the up arrow key for 5 seconds Cm The current chamber temperature on the temperature display changes E Ls to function code FOO and the first figure 0 blinks First fiqure is chanaeable NIPA 3 Depress the up arrow key 4 times A ET The display changes to F04 from FOO UD E AE The figure changes between 0 and 9 by depressing the up arrow key Change of first figure 4 Depress the set key once E 3 AI P The current setting 10 is displayed and the first figure 0 blinks SET in ee E ee E l tt The initial setting 10 low temperature alarm works when the chamber pis ZTN temperature is 10 C lower than the chamber set temperature is displayed at the first setting after installation 5 Dep
59. y ON OFF operation of the compressor When the compressor is OFF stopped the frost on the evaporator is melted by the heater This defrosting never influences to the refrigerator temperature Defrosting by defrost sensor The cycle defrosting may not be sufficient to remove the frost on the evaporator when the ambient temperature is high the door is opened frequently or heavy moist items are stored m the refrigerator In this case the defrosting operation is started automatically when the defrost sensor detects the frost During the defrosting the current refrigerator temperature and dF is displayed alternately when the indicator for refrigerator temperature 1s lit After completion of defrosting dF display is disappeared and the refrigerator returns to the normal operation Important During the defrosting the refrigerator temperature reaches around 10 C temporary Defrost in freezer The freezer has no automatic defrosting system Stop the freezer operation and remove the frost when the frost 1s accumulated in the freezer Following shows the procedure for defrosting 1 Move all storage items in the freezer to other freezer 2 Stop the freezer operation according to the procedure on page 18 lt gt The current freezer temperature and OFF is displayed alternately when the indicator for freezer temperature is lit Only the current refrigerator temperature is displayed when the indicator for refrigerator temp

User Manual for Model MPR-715F-PA Biomedical

Contents

Download Pdf Manuals

Related Search

Related Contents