INNOHOME Stove Guard SGK300
Contents
1. still triggers a false alarm When a false alarm is no longer triggered then make sure that the Stove Guard still responds to the alarm signals of external alarms by re testing the Alarm Signal Detection feature as advised in section 6 2 e Itis also possible to disable the Alarm Signal Detection feature see section 4 Disabling the Alarm Signal Detection feature Sometimes when a burner is on a low heat setting the cooker lights shut down for a cou ple of seconds e This is a normal function of the Stove Guard In electric cookers with mechanical knobs ex cept in cookers with a clock when a burner is turned on a very low heat the Stove Guard performs a check every 15 minutes to see if the cooker is still being used The Safety Lock did not activate within 20 minutes e Check the setting of the Control Unit as advised in section 8 If the Safety Lock was not acti vated redo the setup process as described in section 5 The Intelligent Timer did not cut off the electricity supply in 3 hours In some cookers that are operated by touch or that have a clock and with the SGK300 3 model in all electric cookers the Intelligent Timer will not start when a hotplate is on a very low setting What to do when changing the cooker to a new one e If your hob type has changed ie you used to have an electric cooker and now you have a dual fuel cooker with gas burners change the hob type setting see section 7 e Return the Intell2. cooker automatically limits a temperature in crease When the alarm has been reset manually it cannot be triggered by the rate of temper ature change for 30 minutes but can still be triggered by the heat level The Stove Guard is an additional safety device that does not necessarily cover all possible hazardous situations but does significantly improve cooker safety b Intelligent Timer Electric cookers The Intelligent Timer identifies a burner that has been accidentally left on by monitoring burner heat adjustments If a burner has been left on the cooker is turned off within a time period between 30 minutes and 3 hours depending on the burner setting the higher the setting the sooner the cooker is turned off in some cookers the oven is not turned off Before the cooker is turned off the Control Unit will emit a one minute long pre alarm signal see Control Unit pre alarm signal on previous page Resetting the pre alarm signal will restart the Timer Note that in some cookers that are operated by touch or have a clock and with the SGK300 3 model in all electric cookers the Intelligent Timer does not necessarily start if the burner is on avery low heat setting STOVE GUARD SGK300 USER MANUAL 1 Innohome Stove Guard and how to use it cont Gas and dual fuel cookers timer The timer has a fixed time and starts when the hob tempera ture starts to rise The cooker is turned off after two hours in some dual fuel cookers
3. from the Intelligent Heat Sensor The Sensor will emit a signal when the battery is con nected Initialize the Intelligent Heat Sensor by pressing the push button once Y GE A GZ al Gas burners Press the Intelligent Heat Sensor push but ton and hold it down Whilst holding the push button remove the protective plastic strip see image 1 on page 19 from the Sensor The Intelligent Heat Sensor will emit 2 3 two signals signifying that the battery is connected and that the Sensor has been initialized and set to gas burners setting After hearing the signals release the push button If the Intelligent Heat Sensor only emits one signal while connecting the battery the gas burners setting was not implemented successfully In this case see Changing the hob type setting section 7 3 Attach the Intelligent Heat Sensor underneath the cooker hood with magnets as close to the central point of the cooker as possible If the cooker hood has lights make sure there is at least 10 cm 4 distance between the lights and the Intelligent Heat Sensor If the magnets do not stick to the hood the Intelligent Heat Sensor can be attached using magnetic tape 1 If using magnetic tape first make sure that the attaching surface is cleaned and dry With gas cookers the Intelligent Heat Sensor needs to be installed at the minimum height of 65 cm 26 If the cooker has no cooker hood the Intelligent Heat Sensor can be ins
4. supported housing for example set the sensitivity level manually Electric burners see recommended sensitivity level from the table below Gas burners see the table in the gas installation kit manual Note that when the Intelligent Heat Sensor is installed on the wall it needs to be attached at the height of approx 40 cm 16 for electric burners 65cm 26 for gas burners cm 120 90 80 70 60 50 40 30 inch 39 35 32 28 24 20 16 11 level 1 2 3 4 5 6 8 16 Electric burners sensitivity level The grey area indicated in the table 30 65 cm 11 26 shows where manual setting of the sensitivity level is not required unless it is pre adjusted to a certain level The level is indicated by the numbers 1 to 16 where 1 represents the most sen sitive level and 16 the least sensitive The factory setting is 5 Setting the sensitivity level manually 1 a For a new Intelligent Heat Sensor Remove the protective plastic strip from the Intelligent Heat Sensor In the following 20 seconds carry out the procedure described below in steps 2 5 b For an Intelligent Heat Sensor that has already been installed Detach the Intelligent Heat Sensor Mark the Sensor s original installation location if nec essary it is important to ensure that after procedures the Sensor is returned back to its original installation location An Intelligent Heat Sensor that is attached with screws can be removed by sliding it sideways see i
5. the Intelligent Heat Sensor not being in its original installation location or if the Sensor has not been installed cor rectly If the fault diagnosis detects something abnormal in the functioning of the system the Con trol Unit will emit a fault signal a short signal followed by a long signal be beep at approxi mately 5 second intervals and after a minute s time it will turn the cooker off If the fault diagnosis is signalling press the Intelligent Heat Sensor push button once during the first minute of the alarm If the fault diagnosis alarm was triggered by a temporary glitch or by the Intelligent Heat Sensor not being in its original installation location the cooker shut down will be prevented and cooking can be continued normally If the fault diagnosis alarm was caused by an actual fault situation the alarm cannot be reset and the cooker is turned off If the cooker has been turned off by the fault diagnosis the Control Unit carries on signalling the fault alarm signal it can be turned back on by first turning all cooker knobs to 0 then by turning the electricity supply off for 15 seconds using the main switch If the fault diagnosis has detected a problem first make sure that the Intelligent Heat Sensor is in its original instal lation location If the automatic fault diagnosis carries on detecting a problem contact the product retailer For gas dual fuel cookers Refer to the gas kit manual 1 6 Additional devic
6. If the situation is not hazardous press the Intelligent Heat Sensor push button once during the pre alarm signal The Stove Guard will learn that this kind of a situation is a normal cooking situation When the cooker has been turned off and the Stove Guard is signalling first turn all cooker knobs to 0 then press the Intelligent Heat Sensor push button once In cook ers that are operated by touch just press the Intelligent Heat Sensor push button once STOVE GUARD SGK300 USER MANUAL 1 Innohome Stove Guard and how to use it cont 1 2 Structure of the Stove Guard The Stove Guard is composed of an Intelligent Heat Sen sor attached underneath the cooker hood on the wall or on the cooker panel and a Control Unit connected to the cooker With the additional Innohome Smart Socket vari ous distance alarms like flashing lights or vibrating alarms can be linked to the system The Intelligent Heat Sensor the Control Unit and the Smart Socket communicate using a radio connection The Stove Guard can also be used with gas and dual fuel cookers with the additional gas installation kit including an electric valve that is fitted into the cooker gas supply The Control Unit has an alarm output that enables the Stove Guard to be linked to social alarm systems such as Telecare The push button 1 resets the alarm recon nects the gas electricity supply to the cooker and turns off the Safety Lock Green light 2
7. UARD SGK300 USER MANUAL 7 Changing the hob type setting The Intelligent Heat Sensor uses different settings for gas and electric burners Changing the hob type setting may be required if the gas burners setting was not successfully implemented during the Intelligent Heat Sensor setup or if you later change your cooker to a different type Changing the setting Remove the Intelligent Heat Sensor from its location and mark the Sensor s original installation location if necessary it is important to ensure that after procedures the Sensor is returned back to its original installation location An Intelligent Heat Sensor that is attached with screws can be removed by sliding it sideways see image 8 on page 20 Open the cover by undoing the screw see image 2 on page 19 Insert a plastic or cardboard card or the plastic slip that was originally used to separate the battery in between the battery and its connection so that the card slip separates the battery Press the Intelligent Heat Sensor push button down Whilst holding the push button remove the card slip which connects the battery again After the In telligent Heat Sensor emits a signal two signals release the push button The Intelligent Heat Sensor will emit either one or two signals depending on the setting it has been changed to One signal signifies electric burners setting two signals signifies gas burners setting Close the cover by fastening the screw 8 Checking the C
8. a EE me h Ee PASSED Test 3 2012 NBL F12102 SINTEF www innohome com Congratulations You now own one of the most intelligent cooker safety products in the world Eri Intelligent Heat Sensor 5 GS300 Control Unit SGC500 3 1 Innohome Stove Guard and how to use it 1 1 A quick quide 1 2 Structure of the Stove Guard 1 3 Stove Guard use and features 1 4 Meaning of alarm signals 1 5 Automatic fault diagnosis 1 6 Additional devices 2 Monthly Maintenance 3 Low battery alarm 4 Intelligent Heat Sensor Installation 5 Control Unit Installation and Setup 6 Testing after Installation 6 1 Intelligent Heat Sensor test 6 2 Alarm Signal Detection test 6 3 Safety Lock test if activated during the installation 7 Changing the hob type setting 8 Checking the Control Unit settings 9 Setting the sensitivity level of the Intelligent Heat Sensor 10 Alarm output 11 Troubleshooting 12 Technical Information 13 Warranty 14 EU Declaration of Conformity 9 10 11 12 12 12 12 13 13 14 15 15 17 18 18 18 STOVE GUARD SGK300 USER MANUAL 1 Innohome Stove Guard and how to use it 1 1 A quick guide When the Stove Guard is signalling press the Intelligent Heat Sensor push but ton once Also note that When the Intelligent Heat Sensor is emitting a pre alarm signal a short sound fol lowed by a long break ____ __ it has identified a hazardous situation
9. appliance damage caused by negligence or damage caused by failure to follow the instructions properly 14 EU Declaration of Conformity See www innohome com EUdeclaration IMAGES Innohome Ltd www innohome com info innohome com www facebook com innohome Linnoitustie 4B FI 02600 Espoo Finland inno SGK300 000UU1
10. at the Intelligent Heat Sensor is in its original instal lation location If the problem persists contact the product retailer Control Unit two short beeps after turning the Safety Lock off The Safety Lock has been turned off and the electricity reconnected to the cooker The cooker can now be used Control Unit a signal every hour or half hour There has been an error in the identifica tion of the cooker Repeat the setup procedure as described in section 11 under the heading the Con trol Unit signals every hour or half hour Intelligent Heat Sensor and the Control Unit a signal once a minute o e The Intelligent Heat Sensor has a low bat tery Replace the battery see section 3 Pushing the push button on the Intelli gent Heat Sensor once will delay the battery alarm for 12 hours e STOVE GUARD SGK300 USER MANUAL 1 Innohome Stove Guard and how to use it cont 1 5 Automatic fault diagnosis Electric cookers The automatic fault diagnosis ensures that the Stove Guard is working per fectly each time the cooker is used for cooking the diagnosis will not start if the cooker is only used for a short period of time eg to boil water The diagnostic tool analyses the function of the Intelligent Heat Sensor and the Control Unit and the radio communication link between the devices The automatic fault diagnosis alarm can also be triggered by
11. button 1 see image 7 on page 20 until you hear a signal then release the button and press it again until you hear a signal If you hear two signals when releasing the button the Safety Lock has already been activated and you can finish here Turn any of the hotplates on for 5 seconds then turn it off Wait until you hear a signal to signify the end of setup time Electric cookers with mechanical knobs when you want to deactivate the Safety Lock Press the Control Unit setup button 1 until you hear a signal then release the button and press it again until you hear a signal or sometimes two signals depending on the previous setting Turn a hotplate on wait until you hear a beep from the Control Unit then turn it off External safety systems Telecare The Stove Guard is connected to an external system via the alarm output 2 see image 7 on page 20 More detailed instructions can be found at www innohome com External smoke carbon monoxide and gas alarms All external smoke carbon monoxide and gas alarms need to be installed within 5 metres distance of the Stove Guard Control Unit After installation test alarm signal detection as ad vised in section 6 2 STOVE GUARD SGK300 USER MANUAL 6 Testing after Installation 6 1 Intelligent Heat Sensor test Turn a burner on Press the Intelligent Heat Sensor push button and hold it down until you hear a signal The Control Unit will turn the cooker off by cutting its gas e
12. cooker off This has probably happened due to a wrong installation place that becomes apparent when the cooker is used on a high power setting The cooker can be turned back on by turning the electricity off for a moment using the main switch If the overheating protection turns the cooker off again change the Control Unit installation location to a cooler one or to one that has better ventilation The Intelligent Heat Sensor alarm sounds in a non hazardous situation e When the Intelligent Heat Sensor is first installed it needs to adjust to the kitchen environ ment and learn the users cooking styles If the Intelligent Heat Sensor starts to signal in a normal cooking situation press the Sensor push button during the pre alarm signal This will cause the Intelligent Heat Sensor to reduce its sensitivity automatically The Intelligent Heat Sensor does not signal when it should e Test the Intelligent Heat Sensor as advised in section 6 1 If the Intelligent Heat Sensor nei ther emits a tone nor flashes its light the battery may be flat See section 3 for instructions for changing the battery If the Intelligent Heat Sensor is installed higher than 65 cm for electric burners or higher than 70 cm for gas burners the sensitivity level needs to initially be set to a more sensitive level after which it will self adjust to the environment and to the cooking styles of the us er s If you are not certain whether the level was pre set set t
13. ery alarm signal after the Intelligent Heat Sensor battery has been changed or after it has run out Reset the Control Unit battery signal by turning the cooker electricity off and then back on using the cooker switch the main switch In gas cookers turn the power of the Control Unit off using the main switch or the socket switch Empty battery in the Intelli gent Heat Sensor does not affect the safety features of the Control Unit Unscrewing the screw on the bottom of the Sensor see image 2 on page 19 opens the cover for changing the battery Use CR2032 type batteries When detaching the Intelligent Heat Sensor mark the Sensor s original installation location if necessary it is important to ensure that after procedures the Sensor is returned back to its original installation location An Intelligent Heat Sensor that is attached with screws can be removed by sliding it sideways see image 8 on page 20 STOVE GUARD SGK300 USER MANUAL 4 Intelligent Heat Sensor Installation 1 Remove the Intelligent Heat Sensor from its packaging and allow about 15 minutes for it to reach room temperature 2 The Intelligent Heat Sensor uses different settings for electric and gas burners Carry out initialization as described below depending on hob type If later you wish to change the hob type setting see Changing the hob type setting section 7 Electric burners Remove the protective plastic strip see nae i image 1 on page 19
14. es With the Innohome Smart Sockets additional signalling devices can be joined to the system Several additional signalling devices such as flashing light or vibrating alarms can be linked and placed around the house The Control Unit has an external alarm output that enables the alarms to be transferred to so cial alarm systems such as Telecare See more detailed information about using and installing additional devices from www innohome com STOVE GUARD SGK300 USER MANUAL 2 Monthly Maintenance Electric cookers Since the automatic fault diagnosis tests the Stove Guard operation every time the cooker is used for cooking only the Alarm Signal Detection feature needs to be tested on a monthly basis For the Alarm Signal Detection test refer to the section 6 2 Gas dual fuel cookers Refer to the gas kit manual Clean the Intelligent Heat Sensor by wiping it with a cloth dampened with a mixture of house hold detergent and water Only use a cloth that does not leave fibres Ensure that all other alarms being used with the Stove Guard are cleaned and their batteries changed according to their instructions 3 Low battery alarm A low battery in the Intelligent Heat Sensor causes both the Intelligent Heat Sensor and the Control Unit to emit a signal once a minute The battery alarm can be postponed for 12 hours by pushing the Intelligent Heat Sensor push button once The Control Unit will carry on emit ting the batt
15. g it sideways see image 8 on page 20 Silent alarm Remove the jumper 4 from the 4 5 position Disabling the Alarm Signal Detection feature Change the jumper 5 from the position 2 3 to the position 1 2 Using external power supply The connection cable is available separately Establishing communication with the Innohome Smart Socket The communication link between the Intelligent Heat Sensor and the Smart Socket starts au tomatically Occasionally devices that use X10 transmission may interact with the Smart Sock et In this case change the house address of the Smart Socket manually see the Smart Socket user manual Return to factory settings This may be required if you change your cooker to a new one Detach the Intelligent Heat Sensor An Intelligent Heat Sensor that is attached with screws can be removed by sliding it sideways see image 8 on page 20 Open the cover by undoing the screw see image 2 on page 19 Detach the battery then place it back Push the push button down and hold it until you hear three separate signals then release the push button The Intelligent Heat Sensor has now been returned to its factory settings STOVE GUARD SGK300 USER MANUAL 5 Control Unit Installation and Setup If the cooker is connected to the mains electricity via a plug and a socket the Control Unit can be installed by the user In any other case the installation needs to be carried out by a
16. he level again see section 9 Ifthe Intelligent Heat Sensor still does not work contact the product retailer STOVE GUARD SGK300 USER MANUAL 11 Troubleshooting cont The Control Unit emits a short signal followed by a long signal be beep at approxi mately 5 second intervals e The automatic fault diagnosis has detected that the Intelligent Heat Sensor is not in its origi nal installation location or that there is a temporary problem in the connection between the Intelligent Heat Sensor and the Control Unit or in the functioning of some part of the sys tem The fault diagnosis alarm can also be triggered by the Intelligent Heat Sensor not being installed correctly To turn the cooker back on first turn all cooker knobs to 0 then turn the electricity off for about 15 seconds using the main switch e Ensure that the Intelligent Heat Sensor is in its original installation location e If the automatic fault diagnosis carries on finding a problem contact the product retailer The Control Unit signals every hour or half hour e There has been an error in the identification of the cooker Repeat the setup procedure in the following manner 1 Turn the electricity off for 15 seconds using the main switch 2 Let the electricity be on for 5 seconds 3 Turn the main switch off again for another 15 seconds After turning the electricity back on the Control Unit will emit a signal signifying that the setup has been comple
17. igent Heat Sensor to its factory settings see section 4 If it is installed higher than 65cm 26 for cookers with electric burners or 70cm 28 for gas burners set the sensi tivity level manually see section 9 What to do when replacing the Intelligent Heat Sensor or the Control Unit with a new one See www innohome com for device pairing instructions STOVE GUARD SGK300 USER MANUAL 12 Technical Information Certification CE Casing IP20 Patent Fl 117526 Fl 117878 PCT pending Cut off time Connection Features Voltage power Control 1 3 phase SGC500 2 230VAC 0 5 3h Alarm Signal Detection Unit 1 phase and star Intelligent Timer Intelligent Timer SGC500 connection 1 x 32A Safety Lock only or2x16A SGC500 2 SGC500 3 400VAC Automatic fault diag delta connection nosis 3 x 16A without N Alarm output 1W Connection for power ing external units Overheating and over load protection Intelligent Wireless Battery 5 years 3 25 min Intelligent Heat Sensor Heat Sen 433MHz lifespan Overheating Max sensing distance sor SGS300 10mW X10 or external power Monitor 1 2m 3 9 ft A1 NO supply 5V Adjustable sensitivity Alarm 85 dB Manual and automatic 10cm alarm reset 13 Warranty This product has a 5 year warranty that covers defects in material or workmanship starting from the date of purchase The warranty does not cover any indirect damage caused by a mal functioning
18. lectricity supply and start to emit a signal To turn the cooker back on first turn the burner off not required in cook ers that are operated by touch then press the Intelligent Heat Sensor push button once 6 2 Alarm Signal Detection test Turn the smallest burner to medium heat and test the fire carbon monoxide and gas alarms one at a time When the Control Unit detects an alarm signal it turns the cooker off and starts to emit a signal To turn the cooker back on first turn the burner off not required in cookers that are operated by touch then press the Intelligent Heat Sensor push button once The Stove Guard is factory set to identify most alarm signals If the Stove Guard does not react to the external alarm signal adjust the signal recognition frequency as advised in Troubleshoot ing section 11 6 3 Safety Lock test if activated during the installation Make sure the hob is turned off In approximately 20 minutes the Safety Lock locks the cook er Test the Safety Lock by trying to turn the burners on one by one Turn the Safety Lock off by pushing the Intelligent Heat Sensor push button once or turn one of the cooker knobs on and off three times at one second intervals turn on turn off wait 1 sec turn on turn off wait 1 sec turn on turn off The Control Unit will emit two signals after a short pause indicating that the electricity has been reconnected and the cooker can be used normally STOVE G
19. lights up at one minute intervals and when the Sensor push button is being pressed A red light flashes during an alarm Distinguishing the Stove Guard type Stove Guard SGK300 2 includes a Control Unit SGC500 2 with one blue connector SGK300 3 includes a Control Unit SGC500 3 with two white connec tors 1 3 Stove Guard use and features Stove Guard use When the cooker has been turned off and the Stove Guard is signalling first turn all cook er knobs to 0 then press the Intelligent Heat Sensor push button once In cookers that are operated by touch just press the Intelligent Heat Sensor push button once An intelligent Heat Sensor pre alarm signal that has a short sound and a long break ___ ____ sounds one minute before turning the cooker off If the situation is not hazard ous press the Intelligent Heat Sensor push button once during the pre alarm signal The Intel ligent Heat Sensor will learn that the situation was not hazardous A Control Unit pre alarm signal sounds from behind the cooker that has a short sound and a long break ___ ___ indicates that the Intelligent Timer will turn the cooker off after one minute s time By pressing the Intelligent Heat Sensor push button once you will get more time to use the cooker If the Safety Lock has locked the cooker you can get it back in use by pressing the Intelli gent Heat Sensor push button once STOVE GUARD SGK300 USER MANUAL 1 Innohome Stove Gua
20. lli gent Heat Sensor is attached above the cooker the Control Unit signal sounds from behind the cooker Sound Intelligent Heat Sen sor a short beep every few seconds Meaning The Intelligent Heat Sensor has identified a high temperature or a steep temperature rise above the cooker Overheating Moni tor This is the Intelligent Heat Sensor pre alarm signal that is emitted one minute before the cooker is turned off Reset the pre alarm signal if it was triggered by a normal cooking situation this will cause the Intelligent Heat Sensor to reduce its sensitivity automatically and will prevent the cooker shutdown Course of Action Press the Intelligent Heat Sensor push button once during the pre alarm signal Intelligent Heat Sen sor repetitive fast beep beep beep The Intelligent Heat Sensor has identified a high temperature or a steep temperature rise above the cooker Overheating Mon itor alarm the cooker has been turned off First turn all cooker knobs to 0 then press the Intelligent Heat Sensor push button once In cookers that are operated by touch just press the Intelligent Heat Sensor push button once Control Unit a short beep every few sec onds This is the Control Unit pre alarm signal that sounds for one minute before the Intelligent Timer turns the cooker off By pressing the Intelligent Heat Sensor push button once during the p
21. mage 8 on page 20 Open the cover by unscrewing the screw on the bottom of the Sensor see image 2 on page 19 Disconnect the Intelligent Heat Sensor battery then reconnect it In the following 20 seconds carry out the procedure described below in steps 2 5 After completing step 5 close the Intelligent Heat Sensor cover by tightening the screw on the bottom of the Sensor 2 Hold the Intelligent Heat Sensor push button for about 5 seconds until you hear a signal 3 Release the push button and hold again until the Intelligent Heat Sensor emits a signal 4 Now press the push button as many times as the level 1 16 you wish to set it to Wait that the Sensor light turns off before pressing again 5 The Intelligent Heat Sensor will now emit twice as many signals as the level it is set to in two lots 2 2 signals for level 2 3 3 signals for level 3 4 4 signals for level 4 and so on STOVE GUARD SGK300 USER MANUAL 10 Alarm output The alarm output is a 3 5 mm stereo jack found CN1 on the Control Unit The alarm output is potential A free and normally open opto It closes for one Al arm second when the Control Unit cuts the gas or out NO electricity supply OC1 If the alarm output does not work properly change the polarity of the cable connecting to the alarm output 11 Troubleshooting The cooker has been turned off and no signal sounds e The Control Unit overheating protection has turned the Control Unit and the
22. ontrol Unit settings The Control Unit settings can be checked by turning the power of the cooker off using the cooker switch the main switch and turning it back on after 15 seconds In gas cookers turn the power of the Control Unit off using the main switch or the socket switch The Control Unit will then emit signals to inform you about its settings SGK300 3 or SGK300 2 in a cooker that has a clock or BEEP 20 seconds break BEEP BEEP that is operated by touch SGK300 2 in a cooker with mechanical knobs Safety BEEP BEEP 20 seconds break BEEP Lock activated SGK300 2 in a cooker with mechanical knobs Safety BEEP 20seconds break BEEP Lock deactivated BEEP 20 seconds break BEEP BEEP BEEP SGK300 2 in a gas cooker STOVE GUARD SGK300 USER MANUAL 9 Setting the sensitivity level of the Intelligent Heat Sensor The sensitivity level determines the level of heat and the rate of temperature change required to trigger an alarm The Intelligent Heat Sensor reduces its sensitivity automatically when the user presses the Intelligent Heat Sensor push button during the Intelligent Heat Sensor pre alarm signal see section 1 3 If the Intelligent Heat Sensor is installed to a cooker hood that is higher than 65 cm 26 for electric burners or higher than 70 cm 28 for gas burners or if one wants to pre adjust the sensitivity to a certain level when used in
23. qualified electrician Turn the electricity off at the main switch Attach the Control Unit to the wall using screws or adhesive tape near the electricity outlet and as close to the floor level as possible Attach the Control Unit so that the connectors are facing downwards Installation by the user connect the Control Unit between the cooker s plug and the socket Installation by an electrician connect the Control Unit to the cooker using an Innohome Junc tion Box or an Innohome Connection Cable Turn the electricity back on at the main switch The connection between the Intelligent Heat Sensor and the Control Unit will start automatically After approximately 5 seconds carry out the setup procedure described below note start the procedure within 30 seconds Cook ers that are operated by touch cookers that have a clock or when using the SGK300 3 model no setup procedure is needed The Control Unit will emit two signals after a moment meaning that the Stove Guard is ready for use Setup procedure and programming the Safety Lock Gas cookers Press the Control Unit setup button 1 see image 7 on page 20 until you hear a signal then release the button and press it again until you hear a signal After a short moment the Control Unit will emit another signal which signifies that the Stove Guard setup has been completed Electric cookers with mechanical knobs when you want to activate the Safety Lock Press the Control Unit setup
24. rd and how to use it cont Stove Guard features a Overheating Monitor The Intelligent Heat Sensor installed above the cooker reacts to a dangerously high tempera ture or steep temperature rise The Sensor s self adjusting technology learns the users cook ing styles making hazard recognition precise with no false alarms The rate of temperature increase alarm is based on the steep temperature rise that happens when the cooking vessel s liquid has dried out Reacting to the temperature rise allows for an early detection and preven tion of fire risk situations The Intelligent Heat Sensor will first sound a one minute long pre alarm signal see Intelligent Heat Sensor pre alarm signal on previous page after which the cooker is turned off Resetting the pre alarm signal causes the Intelligent Heat Sensor to become less sensitive The Intelligent Heat Sensor alarm is also reset automatically in about two minutes after the cooker has been turned off and the temperature starts to drop After automatic alarm reset the cooker is turned back on normally first turn all cooker knobs to 0 then press the Intelligent Heat Sensor push button once In cookers that are operated by touch the electricity supply is returned automatically burners are off after the electricity cut off N B The Overheating Monitor alarm is not triggered if the hob s temperature is too low for a hazardous situation to be identified or if the
25. re alarm signal the cooker shutdown can be pre vented Press the Intelligent Heat Sensor push button once during the pre alarm signal STOVE GUARD SGK300 USER MANUAL 1 Innohome Stove Guard and how to use it cont Sound Control Unit a short signal at approximate ly 5 second intervals Meaning The cooker has been turned off due to the Intelligent Timer function detecting the alarm signal of an external smoke carbon monoxide or gas alarm or the Overheat ing Monitor detecting a dangerously high temperature or a steep temperature rise Course of Action First turn all cooker knobs to 0 then press the Intelligent Heat Sensor push button once In cookers that are operated by touch just press the Intelligent Heat Sensor push button once Control Unit a short signal followed by a long signal be beep at approximately 5 second intervals es The cooker has been turned off due to the automatic fault diagnosis detecting a tem porary error in the Intelligent Heat Sensor s connection to the Control Unit or in the functioning of a part of the system The automatic fault diagnosis alarm can also be triggered by the Intelligent Heat Sensor not being in its original installation loca tion or if the Sensor has not been installed correctly First turn all cooker knobs to 0 then turn the electricity off for around 15 seconds using the main switch En sure th
26. talled on the wall or if the cooker has a panel on the back on the cooker panel Install the Sensor on the wall using screws see images 2 6 pages 19 and 20 at the height of approx 40 cm 16 above the cooker for electric burners 65 cm for gas burners The Sensor is installed on the cooker panel using a bracket available separately 4 The sensitivity level is factory set to suit most installations However if the Intelligent Heat Sensor is installed higher than 65 cm 26 for electric burners or higher than 70 cm 27 5 for gas burners or if one wants to pre adjust the sensitivity level to a certain level when used in STOVE GUARD SGK300 USER MANUAL 4 Intelligent Heat Sensor Installation cont supported housing for example set the sensitivity level manually section 9 The screw 2 see image on previous page on the bottom of the Intelligent Heat Sensor opens the cover for changing the battery Options Optional features are turned on off using jumpers 3 see image on previous page A jumper is a type of a short conductor that can be REE removed or changed to another position When detaching the Intel Il z ligent Heat Sernsor mark the Sensor s original installation location if a X 5 necessary it is important to ensure that after procedures the Sensor is 5 6 returned back to its original installation location An Intelligent Heat Sensor that is attached with screws can be removed by slidin
27. ted Then carry out the Safety Lock activation deactivation if appli cable only SGK300 2 in electric cookers with mechanical knobs excluding cookers with a clock Activation Turn any of the hotplates on for 5 seconds then turn it off Wait until you hear a signal Deactivation Turn a hotplate on wait until you hear a beep from the Control Unit then turn it off The Control Unit did not identify the alarm signal of the smoke CO gas alarm e Clean the alarm with a vacuum cleaner e Change the batteries in the alarm if necessary e Check that the alarm is not located too far from the Control Frequency adjustment Unit The alarms should be located at a maximum distance of 16 5ft 5 metres Adjust the signal recognition frequency by turning the trimmer on the Control Unit using a screwdriver frequency adjustment see the picture Turn the trimmer slowly between tests until the Control Unit identifies the signal The Control Unit responds to other sounds e g a telephone ringing or noise from a tele vision e Change the telephone s ring tone or turn down the volume on the television If the signal that causes the false alarm cannot be disabled adjust the signal recognition frequency by turning the trimmer on the Control Unit using a screwdriver frequency adjustment see pic ture above turn the trimmer slowly approx 0 5mm at any one time then see if the sound STOVE GUARD SGK300 USER MANUAL 11 Troubleshooting cont
28. the oven is not turned off Before the cooker is turned off the Control Unit will emit a one minute long pre alarm signal see Control Unit pre alarm signal on page 2 Resetting the pre alarm signal will give two hours more time c Alarm Signal Detection fire carbon monoxide and gas alarms The Stove Guard identifies external fire carbon monoxide or gas alarm signals using sound detection An alarm signal emitted by an external alarm triggers the Stove Guard to turn the cooker off in some cookers the oven is not turned off d Cooker knob Safety Lock The Safety Lock can only be used with the SGK300 2 model and only on electric cookers with mechanical knobs excluding cookers with a clock The Safety Lock locks the cooker so that it cannot be turned on accidentally for example by a child a person with memory disorders or a pet To use the cooker press the Intelligent Heat Sensor push button once or turn one of the cooker knobs on and off three times at one second intervals on off wait one second on off wait one second on off The Control Unit emits two signals as the cooker is ready for use The Safety Lock feature can be activated or deactivated by carrying out the Control Unit setup see section 5 STOVE GUARD SGK300 USER MANUAL 1 Innohome Stove Guard and how to use it cont 1 4 Meaning of alarm signals The Intelligent Heat Sensor signal has a higher tone than the Control Unit signal The Inte
Download Pdf Manuals
Related Search