Cordless Slide Compound Saw
Contents
1. Outer flange Inner flange Spindle Saw blade Hex bolt Os Bon 001783 Arrow Blade case Saw blade Arrow FON 002217 1 Dust nozzle 2 Fastener 3 Dust bag 16 To install the blade mount it carefully onto the spindle mak ing sure that the direction of the arrow on the surface of the blade matches the direction of the arrow on the blade case Install the outer flange and hex bolt and then use the socket wrench to tighten the hex bolt left handed securely counter clockwise while pressing the shaft lock Return the blade guard and center cover to its original posi tion Then tighten the hex bolt clockwise to secure the center cover Release the handle from the raised position by pulling the stopper pin Lower the handle to make sure that the blade guard moves properly Make sure shaft lock has released spindle before making cut Dust bag The use of the dust bag makes cutting operations clean and dust collection easy To attach the dust bag fit it onto the dust nozzle When the dust bag is about half full remove the dust bag from the tool and pull the fastener out Empty the dust bag of its contents tapping it lightly so as to remove particles adher ing to the insides which might hamper further collection NOTE If you connect a Makita vacuum cleaner to your saw more efficient and cleaner operations can be performed Securing workpiece A WARNING e Itis extremely important to alw2. Triangular rule Lock off button 2 pcs Various type of Makita genuine batteries and chargers 27 Makita Corporation 88423107
3. switch does not turn it on and off Warning The use of any accessory or attachment other than recommended in this instruction manual or the catalog may present a risk of personal injury Ensure that the battery pack is correct for the tool Ensure that the outside surface of battery pack or tool is clean and dry before plugging into charger Ensure that batteries are charged using the correct charger recommended by the manufacturer Incorrect use may result in a risk of electric shock overheating or leak age of corrosive liquid from the battery Have your tool repaired by a qualified per son This tool is constructed in accordance with the relevant safety requirements Repairs should only be carried out by quali fied persons using original spare parts other wise this may result in considerable danger to the user Disposal of battery Ensure battery is dis posed of safety as instructed by the manufac turer ADDITIONAL SAFETY RULES FOR TOOL 14 10 11 12 13 Be aware that this tool is always in an operating condition because it does not have to be plugged into an electrical out let Wear eye protection Keep hands out of path of saw blade Avoid contact with any coasting blade It can still cause severe injury Do not operate saw without guards in place Check blade guard for proper clos ing before each use Do not operate saw if blade guard does not move freely and close instantly Never clamp
4. Slide cutting Miter cutting and Bevel cut explanations Cutting repetitive lengths When cutting several pieces of stock to the same length ranging from 220 mm to 385 mm use of the set plate optional accessory will facilitate more efficient opera tion Install the set plate on the holder optional acces sory as shown in the figure Align the cutting line on your workpiece with either the left or right side of the groove in the kerf board and while holding the workpiece from moving move the set plate flush against the end of the workpiece Then secure the 21 001563 1 Cut grooves with blade 22 002193 002221 set plate with the screw When the set plate is not used loosen the screw and turn the set plate out of the way NOTE Use of the holder rod assembly optional accessory allows cutting repetitive lengths up to 2 200 mm approximately Groove cutting A dado type cut can be made by proceeding as follows Adjust the lower limit position of the blade using the adjusting screw and the stopper arm to limit the cutting depth of the blade Refer to Stopper arm section described on previously After adjusting the lower limit position of the blade cut parallel grooves across the width of the workpiece using a slide push cut as shown in the figure Then remove the workpiece material between the grooves with a chisel Do not attempt to perform this type of cut us
5. battery charger into the proper AC voltage source The charging light will flash in green color Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the charger Insert the cartridge fully into the port so that it rests on the charger port floor When the battery cartridge is inserted the charging light color will change from green to red and charging will begin The charging light will remain lit steadily during charging When the charging light color changes from red to green the charging cycle is complete If you leave the battery cartridge in the charger after the charging cycle is complete the charger will switch into its trickle charge maintenance charge mode After charging unplug the charger from the power source Refer to the table below for the charging time 003267 Battery type Capacity Ah Number of cells Charging time 1822 2 0 15 Appprox 45min 1833 2 2 15 Appprox 50min 1834 2 6 15 Appprox 60min 1835 3 0 15 Appprox 70min NOTE The battery charger is for charging Makita battery cartridge Never use it for other purposes or for other manufacturer s batteries When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time it may not accept a full charge This is a normal condition and does not indicate a problem You can
6. blade brake system is not a substitute for blade guard NEVER USE TOOL WITHOUT A FUNCTIONING BLADE GUARD SERIOUS PERSONAL INJURY CAN RESULT A CAUTION e Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool Socket wrench storage The socket wrench is stored as shown in the figure When using the socket wrench pull it out of the wrench holder After using the socket wrench return it to the wrench holder Installing or removing saw blade A CAUTION e Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the blade e Use only the Makita socket wrench provided to install or remove the blade Failure to do so may result in overtightening or insufficient tightening of the hex bolt This could cause an injury oo2198 Lock the handle in the raised position by pushing in the stop per pin oo2215 To remove the blade use the socket wrench to loosen the hex bolt holding the center cover by turning it counterclock wise Raise the blade guard and center cover Blade Case Hex bolt Socket wrench Blade guard Pons ooz216 Press the shaft lock to lock the spindle and use the socket wrench to loosen the hex bolt clockwise Then remove the hex bolt outer flange and blade Shaft lock Arrow Blade case Socket wrench Hex bolt i 2 3 4 5 15 003499
7. gases Keep children away Do not let visitors touch the tool Keep visitors away from work area Store batteries or idle tools When not in use tools and batteries should be stored separately in a dry high or locked up place out of reach of children Ensure that battery terminals cannot be shorted by other metal parts such as screws nails etc Do not force the tool It will do the job better and safer at the rate for which it was intended Use the right tool Do not force small tools or attachments to do the job of a heavy duty tools Do not use tools for purposes not intended Dress properly Do not wear loose clothing or jewellery they can be caught in moving parts Non skid footwear is recommended when working outdoors Wear protecting hair covering to contain long hair Use protective equipment Use safety glasses and if the cutting operation is dusty a face or dust mask Connect dust extraction equipment If devices are provided for the connection of 10 11 12 13 14 15 16 17 18 dust extraction and collection ensure these are connected and properly used Do not abuse the supply cord if fitted Never carry the tool by the cord or yank it to disconnect from the socket Keep the cord away from heat oil and sharp edges Secure the work Use clamps or a vice to hold the work It is safer than using your hand and it frees both hands to operate the tool Do not over reach K
8. or tie the blade guard into the open position Do not perform any operation freehand The workpiece must be secured firmly against the turn base and guide fence with the vise during all operations Never use your hand to secure the workpiece Never reach around saw blade Turn off tool and wait for saw blade to stop before moving workpiece or chang ing settings Remove battery from tool before changing blade or servicing Always secure all moving portions before carrying the tool Stopper pin which locks the cutter head down is for carrying and storage pur poses only and not for any cutting opera tions Don t use the tool in the presence of flam mable liquids or gases Check the blade carefully for cracks or damage before operation Replace cracked or damaged blade imme diately Use only flanges specified for this tool 15 16 18 19 20 21 22 23 24 25 26 27 Avoid cutting nails ENB035 2 Be careful not to damage the arbor flanges especially the installing surface or bolt Damage to these parts could result in blade breakage Make sure that the turn base is properly secured so it will not move during opera tion For your safety remove the chips small pieces etc from the table top before oper ation Inspect for and remove all nails from the workpiece before operation Make sure the shaft lock is released before the switch is turned on Be
9. recharge the battery cartridge fully after discharging it completely and recharging a couple of times If you charge a battery cartridge from a just operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time the charging light may flash in red color If this occurs wait for a while Charging will begin after the battery cartridge cools The battery cartridge will cool 1 Blade guard 10 002245 faster if you remove the battery cartridge from the battery charger e If the charging light flashes alternately in green and red color charging is not possible The terminals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged Trickle charge Maintenance charge If you leave the battery cartridge in the charger to prevent spontaneous discharging after full charge the charger will switch into its trickle charge maintenance charge mode and keep the battery cartridge fresh and fully charged Tips for maintaining maximum battery life 1 Charge the battery cartridge before completely dis charged Always stop tool operation and charge the battery car tridge when you notice less tool power 2 Never recharge a fully charged battery cartridge Overcharging shortens the battery service life 3 Charge the battery cartridge with room temperature at 10 C 40 C 50 F 104 F Let a hot battery cartridge c
10. sure that the blade does not contact the turn base in the lowest position Hold the handle firmly Be aware that the saw moves up or down slightly during start up and stopping Make sure the blade is not contacting the workpiece before the switch is turned on Before using the tool on an actual work piece let it run for a while Watch for vibration or wobbling that could indicate poor installation or a poorly balanced blade Wait until the blade attains full speed before cutting Stop operation immediately if you notice anything abnormal Do not attempt to lock the trigger in the on position Be alert at all times especially during repetitive monotonous operations Don t be lulled into a false sense of security Blades are extremely unforgiving Always use accessories recommended in this manual Use of improper accessories 30 Select saw blades in relation to the mate rial to be cut such as abrasive wheels may cause an injury 28 Do not use the saw to cut other than wood or similar materials 31 Take care when slotting 32 Replace the kerf board when worm 29 Connect miter saws to a dust collecting device when sawing SAVE THESE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER amp BATTERY CARTRIDGE ENC001 3 SAVE THESE INSTRUCTIONS This man 8 Do not operate charger with damaged ual contains important safety and operat cord or plug replace them immediately ing Instructions to
11. ENCE AND THROUGH THE WORK PIECE When the cut is completed switch off the tool and WAIT UNTIL THE BLADE HAS COME TO A COM PLETE STOP before returning the blade to its fully ele vated position A CAUTION Whenever performing the slide cut FIRST PULL THE CARRIAGE TOWARD YOU FULLY and press down the handle to the fully lowered position then PUSH THE CARRIAGE TOWARD THE GUIDE FENCE NEVER START THE CUT WITH THE CARRIAGE NOT FULLY PULLED TOWARD YOU If you perform the slide cut without pulling the carriage fully or if you perform the slide cut toward your direction the blade may kickback unexpectedly with the potential to cause serious PERSONAL INJURY Never perform the slide cut with the handle locked in the lowered position by pressing the stopper pin Never loosen the clamp screw which secures the carriage while the blade is rotating This may cause serious injury Miter cutting Refer to the previously covered Adjusting the miter angle Bevel cut Loosen the lever and tilt the saw blade to set the bevel angle Refer to the previously covered Adjusting the bevel angle Be sure to retighten the lever firmly to secure the selected bevel angle safely Secure the work piece with a vise Make sure the carriage is pulled all the way back toward the operator Switch on the tool without the blade making any contact and wait until the blade attains full speed Then gently lower the handle to the fully lowered position whil
12. HSINSNA Taa kita Cordless Slide Compound Saw Equipped with Electric Brake 190 mm MODEL LS711D 002214 INSTRUCTION MANUAL A WARNING For your personal safety READ and UNDERSTAND before using SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE SPECIFICATIONS Blade diameter 180 190 mm Hole arbor diameter oo cc ceeeceeeceeeeeecneeeeeeeeneeceaeeeeeeseaeeseeeseaeeseeseaeesieeeeaeessaeenas 20 mm Max Miter angle i ec eeeeceeeceeeeeeeeeeeeeeeeeeeeenneeseseeeeeeeeeesseeeesneeesaaes Left 47 Right 57 Max Bevel angle ccceecceceeeeeeeeeceeeeneeeeeeeeeseaeeneeneeeeneeeeeeaeeeensaeeseeeeeseeeeeseeeenenes Left 45 Max Cutting capacities H x W with blade 190 mm in daiameter Bevel angle Miter angle 0 45 left 0 50 mm x 182 mm 35 mm x 182 mm 45 left and right 50 mm x 127 mm 35 mm x 127 mm Note The max Cutting capacities may vary according to workpiece blade and or charging condition No load SPpe d E 2 000 min Dimensions L x W X H oo eeeceeeceeeeeeeeeeeeeeeeeeeeneeteeeeeaeenaees 550 mm x 430 mm x 454 mm Net weight 28 5 si ies oaoa a E O aE 10 5 kg e Manufacturer reserves the right to change specifications without notice e Specifications may differ from country to country Intended use The tool is intended for accurate straight and miter cutting in wood SYMBOLS END303 1 The following show the symbol
13. ause the loss of control which can result in PERSONAL INJURY Holders and holder assembly optional accessories The holders and the holder assembly can be installed on either side as a convenient means of supporting workpieces horizontally Install them as shown in the figure Then tighten the screws firmly to secure the holders and the holder assembly When cutting long workpieces use the holder rod assembly optional accessory It consists of two holder assemblies and two rods 12 A CAUTION Always support long workpieces level with the top surface of the turn base for accurate cuts and to prevent dangerous loss of control of the tool OPERATION 002218 A CAUTION Before use be sure to release the handle from the lowered position by pulling the stopper pin Make sure the blade is not contacting the workpiece etc before the switch is turned on Do not apply excessive pressure on the handle when cutting Too much force may result in overload of the motor and or decreased cutting efficiency Push down handle with only as much force as is necessary for smooth cutting and without significant decrease in blade speed Gently press down the handle to perform the cut If the handle is pressed down with force or if lateral force is applied the blade will vibrate and leave a mark saw mark in the workpiece and the precision of the cut will be impaired During a slide cut gently push the carriage toward the guide f
14. ays secure the workpiece properly and tightly with the vise Failure to do so can cause the tool to be damaged and or the workpiece to 1 2 1 2 3 4 5 6 7 Support Turn base Vise arm Vise rod Guide fence Holder Holder assembly Vise knob Screw be destroyed PERSONAL INJURY MAY ALSO RESULT Also after a cutting operation DO NOT raise the blade until the blade has come to a complete stop A CAUTION e When cutting long workpieces use supports that are as high as the top surface level of the turn base Do not rely solely on the vertical vise and or horizontal vise to secure the workpiece Thin material tends to sag Support workpiece over its entire length to avoid blade pinch and possible KICKBACK Vertical vise The vertical vise can be installed in two positions on either the left or right side of the guide fence or the holder assembly optional accessory Insert the vise rod into the hole in the guide fence or the holder assembly and tighten the screw to secure the vise rod Position the vise arm according to the thickness and shape of the workpiece and secure the vise arm by tightening the screw If the screw to secure the vise arm contacts the guide fence install the screw on the opposite side of vise arm Make sure that no part of the tool contacts the vise when lowering the handle fully and pulling or pushing the carriage all the way If some part contacts the vise re positio
15. e applying pressure in parallel with the blade and PUSH THE CARRIAGE TOWARD 001846 6 1 Set plate 2 Holder 3 Screw THE GUIDE FENCE TO CUT THE WORKPIECE When the cut is completed switch off the tool and WAIT UNTIL THE BLADE HAS COME TO A COMPLETE STOP before returning the blade to its fully elevated position CAUTION Always be sure that the blade will move down to bevel direction during a bevel cut Keep hands out of path of saw blade During a bevel cut it may create a condition whereby the piece cut off will come to rest against the side of the blade If the blade is raised while the blade is still rotating this piece may be caught by the blade causing fragments to be scattered which is dangerous The blade should be raised ONLY after the blade has come to a complete stop When pressing the handle down apply pressure parallel to the blade If the pressure is not parallel to the blade during a cut the angle of the blade might be shifted and the precision of the cut will be impaired Compound cutting Compound cutting is the process in which a bevel angle is made at the same time in which a miter angle is being cut on a workpiece Compound cutting can be performed at angle shown in the table 003400 Miter angle Battery angle Left and Right 45 Left 0 45 Right 50 Left 0 40 Right 55 Left 0 30 Right 57 Left 0 25 When performing compound cutting refer to Press cut ting
16. eep proper footing and balance at all times Maintain tools with care Keep cutting tools sharp and clean for better and safer perform ance Follow instructions for lubrication and changing accessories Inspect tool cords periodically and if damaged have repaired by an authorized service facility Disconnect tools Where the design per mits disconnect the tool from its battery pack when not in use before servicing and when changing accessories such as blades bits and cutters Remove adjusting keys and wrenches Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on Avoid unintentional starting Do not carry the tool with a finger on the switch Stay alert Watch what you are doing Use common sense Do not operate the tool when you are tired Check damaged parts Before further use of the tool a guard or other part that is dam aged should be carefully checked to deter mine that it will operate properly and perform its intended function Check for alignment of moving parts free running of moving parts breakage of parts mounting and any other condition that may affect its operation A guard or other part that is damaged should be properly repaired or replaced by an authorized service facility unless otherwise indicated in this instruction manual Have 19 20 21 defective switches replaced by an authorized service facility Do not use the tool if the
17. ence without stopping If the carriage movement is stopped during the cut a mark will be left in the workpiece and the precision of the cut will be impaired Press cutting cutting small workpieces Workpieces up to 50 mm high and 97 mm wide can be cut in the following way Push the carriage toward the guide fence fully and tighten the clamp screw on the turn base clockwise to secure the carriage Secure the workpiece with the vise Switch on the tool without the blade making any contact and wait until the blade attains full speed before lower ing Then gently lower the handle to the fully lowered position to cut the workpiece When the cut is com pleted switch off the tool and WAIT UNTIL THE BLADE HAS COME TO A COMPLETE STOP before returning the blade to its fully elevated position A CAUTION Firmly tighten the clamp screw on the turn base clockwise so that the carriage will not move during operation Insufficient tightening may cause unexpected kickback of the blade Possible serious PERSONAL INJURY may result 19 20 002219 002220 2 Slide push cutting cutting wide workpieces Loosen the clamp screw on the turn base counterclock wise so that the carriage can slide freely Secure the workpiece with the vise Pull the carriage toward you fully Switch on the tool without the blade making any contact and wait until the blade attains full speed Press down the handle and PUSH THE CARRIAGE TOWARD THE GUIDE F
18. hree revolutions counterclockwise to tilt the blade to the right Carefully square the side of the blade with the top surface of the turn base using the triangular rule try square etc by turning the 0 bevel angle adjust ing bolt clockwise Then tighten the lever securely 1 Screw 2 Pointer 3 Bevel scale T O 002211 002250 1 45 bevel angle adjusting bolt 1 Limit mark 1 Screwdriver 2 Brush holder cap 001145 Make sure that the pointer on the arm point to 0 on the bevel scale on the arm holder If it does not point to 0 loosen the screw which secures the pointer and adjust the pointer so that it will point to 0 2 45 bevel angle Adjust the 45 bevel angle only after performing 0 bevel angle adjustment To adjust left 45 bevel angle loosen the lever and tilt the blade to the left fully Make sure that the pointer on the arm points to 45 on the bevel scale on the arm holder If the pointer does not point to 45 turn the 45 bevel angle adjusting bolt upper bolt on the right side of the arm until the pointer points to 45 Replacing carbon brushes Remove and check the carbon brushes regularly Replace when they wear down to the limit mark Keep the carbon brushes clean and free to slip in the holders Both carbon brushes should be replaced at the same time Use only iden tical carbon brushes Use a screwdriver to remove the brush holder caps Take out the worn carb
19. ing wide thick blades or with a dado blade Possible loss of control and injury may result A CAUTION Be sure to return the stopper arm to the original position when performing other than groove cutting Carrying tool Make sure that the battery cartridge is removed Secure the blade at OAa bevel angle and the turn base at right miter angle fully Secure the slide poles after pulling the carriage toward you fully Lower the handle fully and lock it in the low ered position by pushing in the stopper pin Carry the tool by carrying grip as shown in the figure If you remove the holders dust bag etc you can carry the tool more easily CAUTION Always secure all moving portions before carrying the tool Stopper pin is for carrying and storage purposes only and not for any cutting operations MAINTENANCE 002242 1 Guide fence 2 Hex bolt 002209 HS 1 1 Triangular rule CAUTION Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance WARNING Always be sure that the blade is sharp and clean for the best and safest performance Adjusting the cutting angle This tool is carefully adjusted and aligned at the factory but rough handling may have affected the alignment If your tool is not aligned properly perform the following 1 Miter angle Push the carriage toward the guide fence and tighten the clamp screw
20. lade guard and center cover With the blade guard so positioned cleaning can be more completely and efficiently accomplished When cleaning is complete reverse procedure above and secure bolt Do not remove spring holding blade guard If guard becomes discolored through age or UV light exposure con tact a Makita service center for a new guard DO NOT DEFEAT OR REMOVE GUARD Positioning kerf board This tool is provided with the kerf boards in the turn base to minimize tearing on the exit side of a cut The kerf boards are factory adjusted so that the saw blade does not contact the kerf boards Before use adjust the kerf boards as follows First remove the battery cartridge Loosen all the screws 2 each on left and right securing the kerf boards Re tighten them only to the extent that the kerf boards can still be easily moved by hand Lower the handle fully and push in the stop per pin to lock the handle in the lowered position Loosen the clamp screw which secures the slide poles Pull the carriage toward you fully Adjust the kerf boards so that the kerf boards just contact the sides of the blade teeth Tighten the front screws do not tighten firmly Push the carriage toward the guide fence fully and adjust the kerf boards so that the kerf boards just contact the sides of blade teeth Tighten the rear screws do not tighten firmly After adjusting the kerf boards release the stopper pin and raise the handle Then tighten all the
21. n the vise Press the workpiece flat against the guide fence and the turn base Position the workpiece at the desired cutting position and secure it firmly by tightening the vise knob A CAUTION e The workpiece must be secured firmly against the turn base and guide fence with the vise during all operations 17 001807 1 Vise knob 2 Projection 3 Vise shaft 4 Base 002247 1 Holder 2 Holder assembly 002246 1 Holder assembly 2 Rod 12 18 Horizontal vise optional accessory The horizontal vise can be installed on the left side of the base By turning the vise knob counterclockwise the screw is released and the vise shaft can be moved rapidly in and out By turning the vise knob clockwise the screw remains secured To grip the workpiece turn the vise knob gently clockwise until the projection reaches its topmost position then fasten securely If the vise knob is forced in or pulled out while being turned clockwise the projection may stop at an angle In this case turn the vise knob back counterclockwise until the screw is released before turning again gently clock wise The maximum width of the workpiece which can be secured by the horizontal vise is 120 mm A CAUTION e Grip the workpiece only when the projection is at the topmost position Failure to do so may result in insufficient securing of the workpiece This could cause the workpiece to be thrown cause damage to the blade or c
22. on A CAUTION e Before inserting the battery cartridge into the tool always check to see that the switch trigger actuates properly and returns to the OFF position when released e When not using the tool remove the lock off button and store it in a secure place This prevents unauthorized operation 13 ASSEMBLY 1 Arm 2 Wrench holder 3 Socket wrench 14 002200 e Do not pull the switch trigger hard without pressing in the lock off button This can cause switch breakage To prevent the switch trigger from being accidentally pulled a lock off button is provided To start the tool press in the lock off button and pull the switch trigger Release the switch trig ger to stop A WARNING e NEVER use tool without a fully operative switch trigger Any tool with an inoperative switch is HIGHLY DANGEROUS and must be repaired before further usage e For your safety this tool is equipped with a lock off button which prevents the tool from unintended starting NEVER use the tool if it runs when you simply pull the switch trigger without pressing the lock off button Return tool to a Makita service center for proper repairs BEFORE further usage e NEVER tape down or defeat purpose and function of lock off button Electric brake This tool is equipped with an electric blade brake If the tool consistently fails to quickly stop blade after switch trigger release have tool serviced at a Makita service center The
23. on brushes insert the new ones and secure the brush holder caps After replacing brushes insert the battery cartridge into the tool and break in brushes by running tool with no load for about 1 minute Then check the tool while running and elec tric brake operation when releasing the switch trigger If elec tric brake is not working well ask your local Makita service center for repair After use e After use wipe off chips and dust adhering to the tool with a cloth or the like Keep the blade guard clean 25 ACCESSORIES 26 according to the directions in the previously covered section titled Blade guard Lubricate the sliding portions with machine oil to prevent rust When storing the tool pull the carriage toward you fully so that the slide pole is thoroughly inserted into the turn base A CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons Only use accessory or attachment for its stated purpose If you need any assistance for more details regarding these accessories ask your local Makita service center Carbide tipped saw blades Miter saw blades For smooth and precise cutting in various materials Vise assembly Horizontal vise Vertical vise Socket wrench 10 Holder set Holder assembly Holder rod assembly Set plate Dust bag
24. on the turn base to secure the carriage Loosen the grip which secures the turn base Turn the turn base so that the pointer points to 0 on the miter scale Then turn the turn base slightly clockwise and counterclockwise to seat the turn base in the 0 miter notch Leave as it is if the pointer does not point to 0 Loosen the hex bolts securing the guide fence using the socket wrench Lower the handle fully and lock it in the lowered position by pushing in the stopper pin Square the side of the blade with the face of the guide fence using a triangular rule try square etc Then securely tighten the hex bolts on the guide fence in the order from the right side 23 002210 1 Screw 2 Miter scale 3 Pointer 002858 1 Arm holder 2 Arm 3 0 bevel angle adjusting bolt 4 Lever 001819 1 Triangular rule 2 Saw blade 3 Top surface of turn base 24 Make sure that the pointer points to 0 on the miter scale If the pointer does not point to 0 loosen the screw which secures the pointer and adjust the pointer so that it will point to 0 Bevel angle 1 0 bevel angle Push the carriage toward the guide fence and tighten the clamp screw on the turn base to secure the carriage Lower the handle fully and lock it in the lowered position by pushing in the stopper pin Loosen the lever at the rear of the tool Turn the 0 bevel angle adjusting bolt lower bolt on the right side of the arm two or t
25. ool down before charging it 4 Charge the Nickel Metal Hydride battery cartridge when you do not use it for more than six months Blade guard When lowering the handle the blade guard rises automati cally The guard is spring loaded so it returns to its original position when the cut is completed and the handle is raised NEVER DEFEAT OR REMOVE THE BLADE GUARD OR THE SPRING WHICH ATTACHES TO THE GUARD In the interest of your personal safety always maintain the blade guard in good condition Any irregular operation of the blade guard should be corrected immediately Check to assure spring loaded return action of guard NEVER USE THE TOOL IF THE BLADE GUARD OR SPRING ARE DAM AGED FAULTY OR REMOVED DOING SO IS HIGHLY DANGEROUS AND CAN CAUSE SERIOUS PERSONAL INJURY If the see through blade guard becomes dirty or sawdust adheres to it in such a way that the blade is no longer easily visible remove the battery cartridge and clean the guard 001782 1 Blade guard 002195 1 Clamp screw 2 Kerf board 001800 1 Saw blade 2 Blade teeth 3 Kerf board 4 Left bevel cut 5 Straight cut carefully with a damp cloth Do not use solvents or any petro leum based cleaners on the plastic guard If the blade guard is especially dirty and vision through the guard is impaired use the supplied socket wrench to loosen the hex bolt holding the center cover Loosen the hex bolt by turning it counterclockwise and raise the b
26. orter stop operating immediately It may result in a risk of overheating possi ble burns and even an explosion Do not charge battery cartridge when tem perature is BELOW 10 C 50 F or ABOVE 40 C 104 F Do not attempt to use a step up trans former an engine generator or DC power receptacle Do not allow anything to cover or clog the charger vents Always cover the battery terminals with the battery cover when the battery car tridge is not used Do not short the battery cartridge 1 Do not touch the terminals with any conductive material 2 Avoid storing battery cartridge in a container with other metal objects such as nails coins etc 15 If electrolyte gets into your eyes rinse them out with clear water and seek medi cal attention right away It may result in loss of your eyesight ADDITIONAL SAFETY RULES FOR CHARGER amp BATTERY CARTRIDGE 3 Do not expose battery cartridge to water or rain A battery short can cause a large current flow overheating possible burns and even a breakdown Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 C 122 F Do not incinerate the battery cartridge even if it is severely damaged or is com pletely worn out The battery cartridge can explode in a fire Be careful not to drop shake or strike bat tery Do not charge inside a box or container of any kind The battery must be placed in a
27. r battery charger 9 Do not operate charger if it has received a Before using battery charger read all sharp blow been dropped or otherwise instructions and cautionary markings on damaged in any way take it to a qualified 1 battery charger 2 battery and 3 serviceman product using battery 10 Do not disassemble charger or battery CAUTION To reduce risk of injury charge cartridge take it to a qualified serviceman only MAKITA type rechargeable batteries when service or repair is required Incor Other types of batteries may burst caus rect reassembly may result in a risk of ing personal injury and damage electric shock or fire Do not expose charger to rain or snow 11 To reduce risk of electric shock unplug Use of an attachment not recommended charger from outlet betore attempting aay maintenance or cleaning Turning off con or sold by the battery charger manufac gt a F 5 trols will not reduce this risk turer may result in a risk of fire electric shock or injury to persons 12 The battery charger is not intended for To reduce risk of damage to electric plug at i races OF Anim persons and cord pull by plug rather than cord P when disconnecting charger 13 Young children should be supervised to Make sure cord is located so that it will Pa donot Play with she bat not be stepped on tripped over or other y ger wise subjected to damage or stress 14 If operating time has become excessively sh
28. s used for the tool Be sure that you understand their mean ing before use e Ayten Indoor use only BRD Charging complete Ca sioiias Read instruction manual EENIAS Delay charge too hot battery 0 TERRE DOUBLE INSULATION ATX Deffective battery Oep Ready to charge O_o Charging PEER ET Do not short batteries amp amp NT Always recycle batteries Ni MH Ni Cd PE Do not discard batteries into garbage can or the like NOTE The recycling method may differ from country to country or state province to state prov ince Consult with your nearest Makita Authorized Service Center or Distributor SAFETY INSTRUCTIONS A WARNING When using battery operated tools basic safety precautions including the following should be followed to reduce the risk of fire leaking batteries and personal Q disiedisaceaasis To avoid injury from flying debris keep holding the saw head down after making cuts until the blade has come toa complete stop 3r OE For your safety remove the chips small pieces etc from the table top before operation ENA002 1 injury Read these instructions before operating this product and save these instructions For safe operation 1 Keep work area clean Cluttered areas and benches invite injuries Consider the work environment Do not expose the tool to rain Keep work area well lit Do not use tools in the presence of flam mable liquids or
29. screws securely A CAUTION e Before and after changing the bevel angle always adjust the kerf boards as described above 11 002196 1 Adjusting bolt 2 Guide fence 3 Turn Base 001540 1 Top surface ot turn base 2 Periphery of blade 3 Guide fence 002241 1 Adjusting screw 2 Stopper arm 12 Maintaining maximum cutting capacity This tool is factory adjusted to provide the maximum cutting capacity for a 190 mm saw blade When installing a new blade always check the lower limit position of the blade and if necessary adjust it as follows First remove the battery cartridge Push the carriage toward the guide fence fully and lower the handle completely Use the socket wrench to turn the adjusting bolt until the periph ery of the blade extends slightly below the top surface of the turn base at the point where the front face of the guide fence meets the top surface of the turn base With the battery cartridge removed rotate the blade by hand while holding the handle all the way down to be sure that the blade does not contact any part of the lower base Re adjust slightly if necessary A CAUTION e After installing a new blade always be sure that the blade does not contact any part of the lower base when the handle is lowered completely Always do this with the battery cartridge removed Stopper arm The lower limit position of the blade can be easily adjusted with the stopper arm To adjust i
30. t move the stopper arm in the direction of the arrow as shown in the figure Adjust the adjusting screw so that the blade stops at the desired posi tion when lowering the handle fully 002197 1 Turn base 2 Miter scale 3 Pointer 4 Grip 5 Lock lever 002198 1 Lever 002199 1 Pointer 2 Bevel scale 3 Arm 001811 1 Lock off button 2 Switch trigger Adjusting the miter angle Loosen the grip by turning counterclockwise Turn the turn base while pressing down the lock lever When you have moved the grip to the position where the pointer points to the desired angle on the miter scale securely tighten the grip clockwise A CAUTION e When turning the turn base be sure to raise the handle fully e After changing the miter angle always secure the turn base by tightening the grip firmly Adjusting the bevel angle To adjust the bevel angle loosen the lever at the rear of the tool counterclockwise Push the handle to the left to tilt the saw blade until the pointer points to the desired angle on the bevel scale Then tighten the lever clockwise firmly to secure the arm A CAUTION e When tilting the saw blade be sure to raise the handle fully e After changing the bevel angle always secure the arm by tightening the lever clockwise e When changing bevel angles be sure to position the kerf boards appropriately as explained in the Positioning kerf boards section Switch acti
31. well ventilated area during charging INSTALLATION 002193 002194 1 Bolt FUNCTIONAL DESCRIPTION 002240 1 Battery cartridge 2 Button Bench mounting When the tool is shipped the handle is locked in the lowered position by the stopper pin Release the stopper pin by lower ing the handle slightly and pulling the stopper pin This tool should be bolted with two bolts to a level and stable surface using the bolt holes provided in the tool s base This will help prevent tipping and possible injury A CAUTION Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool Installing or removing battery cartridge Always switch off the tool before insertion or removal of the battery cartridge To remove the battery cartridge withdraw it from the tool while pressing the buttons on both sides of the cartridge To insert the battery cartridge align the tongue on the battery cartridge with the groove in the housing and slip it into place Always insert it all the way until it locks in place with a little click If not it may accidentally fall out of the tool causing injury to you or someone around you Do not use force when inserting the battery cartridge If the cartridge does not slide in easily it is not being inserted correctly 1 Battery charger 2 Battery cartridge 3 Charging light 004513 Charging 1 Plug the
Download Pdf Manuals
Related Search