USER MANUAL - Klavier
Contents
1. single red light in the middle is blinking when motors are in use the yellow or red lights are on according to electrical current CHARGING ROLLERS To recharge rollers disconnect remote control device connect charging wire to each roller and the cigarette lighter socket in the battery charger the 3 red ampere lights go on the 3 red lights go off one by one as batteries charge up when only one red light is on still charge is almost full when only the single green light is on charging is finished and the battery char ger cuts off automatically new batteries can require long charging times charging time varies between 1 and 6 hours depending on battery condition and state of discharge the green volt indicator light is on during charging or the yellow light goes on if batteries are very weak the red indicator light in the middle is off if necessary batteries can be charged by plugging into the vehicle s cigarette lighter socket with engine running Note it is not possible to fully charge batteries using the cigarette lighter socket which will only charge heavily discharged batteries gt charge batteries using Klavier Roller provided charger only An improper charger can damage the electric circuits 10 red red red e green red yellow green red current indicator lights on rollers covers BATTERIES Model YUASA NP17 12 12V 17Ah Valve Regulated Gas Reco2. ES lay wooden boards on staircase and ensure stability boards must overlap use extensions for filling in spaces of a few steps at top of stairway screw half round supporting block onto underside of board and place on last step to keep board from breaking or scraping top of board should not be higher than staircase landing Note the boards bend when roller wheels are on them and particularly over the spaces between stairs This suppleness provides better adherence to stair edges and provides greater overall safety STAIRWELL LANDINGS to be able to turn at 90 or 180 degrees when on a landing the depth and width of the landing must be at least equal to the length of the rollers For example a KR210 cannot turn completely on a landing with less than 210 centimetres 6 11 on a side in the case of a stairway with a flat and straight intermediary landing whose length is shorter than that of the rollers place the aluminium ramp on the landing so the rollers central wheels touch the ground before starting on the second part of the stairway BATTERIES AND BATTERY CHARGING Meaning of indicator lights on roller covers ROLLERS IN USE The remote control device and connecting wire are plugged in meaning of volt indicator lights when motors are stopped green light batteries are fully charged yellow light batteries are discharging red light batteries are weak the 3 red ampere lights are off the
3. KLAVIER ROLLER w w w USER MANUAL SUMMARY Tipping Device p2 Remote Control p4 Motorised Rollers p6 Ramp and Board p8 Charge and Battery p 10 Electric Circuit Diagram p12 KLAVIER ROLLER 353 rue des Marais F 74410 SAINT JORIOZ 33 450 68 99 40 33 668 36 03 89 www klavier roller com TIPPING DEVICE Important The different elements of the tipping equipment are made of plywood with inserted iron nuts Do not over tighten the screws Doing so is not only unnecessary it can also damage the equipment Snug but moderate tightening is sufficient view demonstration video before first use if piano has carrying bars screwed to side remove them if piano has wing nuts protruding under keyboard replace with flat headed screws PUTTING THE PIANO ON EDGE 1 remove pedal lyre 2 attach keyboard box to keyboard adjust slide to fit and tighten knobbed screws tighten keyboard box clamps with knobbed screws without over tightening 3 hang shoe on piano lid by placing the shoe s two rubber coated clasps on top of the lid so that the shoe hangs down the side of the piano 4 position the front of the shoe so that the tongue of the keyboard box fits into the appropriate groove in the shoe 5 attach shoe screw to keyboard box with BTR type hexagonal screws remove from holding holes inside of shoe attach clamp tighten hard tighten piano lid strap secure safety block can be placed after tipping the pi
4. ano 6 attach rear wheel place tire in direction of tipping and in contact with piano case place rubber tongue in downwards position securely tighten screws 7 attach tipping device maintain tipping device in vertical position tighten screws moderately 8 to tip piano on edge lift pivoting leg of tipping device by pulling on left handle remove left leg of piano position carpet under tipping device fold pivoting leg by pulling on right handle of tipping device control tipping movement with keyboard box handle on underside of box remove tipping device and piano legs PUTTING PIANO UPRIGHT 1 put rear wheel and right leg of piano in position 2 attach rear wheel wheel underneath rubber tongue towards piano leg castor 3 attach tipping device tighten screws moderately 4 to swing piano upright pull piano towards you with keyboard box handle leave piano on tipping device and move to other side lift pivoting leg of tipping device by pulling on left handle put left leg of piano in position and place carpet underneath fold in pivoting leg of tipping device by pulling on right handle piano has weight on its leg 5 remove tipping device 6 move piano off of carpet 7 remove shoe clamp screws in keyboard box strap 8 remove keyboard box and rear wheel 9 attach pedal lyre the grooves in the front of the shoe are for positioning the piano so that it is properly balanced on
5. ccording to the colour codes Notice only accidental short circuits may blow the 3A or 10A fuses standard automo tive fuses if the 3A fuse blows nothing will work If the 10A fuse blows only the battery charging doesn t work all relays except N 1 and N 9 are heavy duty and must be replaced by 30A relays The original N 1 and N 9 relays may replace any other relay and may be repla ced by any standard 10A automotive relay 12 RELAY BOARD OUTLAYING RELAY BOARD OUTLAYING IMPORTANT remove battery fuses 25A before any interventions thus avoiding any short circuits rear lifting relay 4 These LED lights are connected in parallel to the corresponding relays coils and light up when a relay is on battery 1 battery 2 battery 2 battery 1 central wheel relay 3 propelling relay 10 battery charge relay 9 O 24 volts on relays 5 amp 6 power on relay 1 gt relay 7 relay8 board 3A 6 common powering B This shorting strap connection 24 volts switching on makes it possible for the 3 4 to increase the lifting motors 2 motors power central wheel motor front lifting a 4 i standard lrs Lie increased front lifting motor S gt rear lifting motor up or down or forwards backwards propulsion motors propelling charging motor Fi battery charger rear liftin
6. g motor This shorting strap selects the actuated roller A right hand roller D Co left hand roller G To remove these connectors Pres here wei za press fastening clip on their lower side to unlock E battery charger 13
7. h caution The instructions written in bold face type must be strictly followed Improper use of the rollers can result in damage to the equipment LOADING THE PIANO 1 position the rollers correctly on either side of the piano keyboard stickers on rollers towards piano keyboard protective carpet against edge of piano 2 pass the iron lifting bars in the rungs under the shoe at the arrow marks 3 first plug in the connecting wire between the rollers and only afterwards the remote control wire 4 first lift piano at the tail end keeping the rollers straight 5 then lift at the keyboard end as indicated by the arrows on the rollers 6 activate the rear lever again to lock the lifting bar 7 remove small stabilizing wheels 8 lift rollers a few centimetres onto the central wheels for manoeuvring UNLOADING THE PIANO 1 be sure that rollers are on all 6 wheels raise central wheels 2 put small lateral stabilising wheels on rollers 3 first lower lifting bars on keyboard end according to arrows on rollers gt Caution if a beeping sound is heard this means that the rollers are raised on the lowered central wheels stop unloading and lower rollers by lifting central wheels 4 lower lifting bar on tail end of piano 5 remove lifting bars and unplug wires 6 use steel shafts for manoeuvring rollers MOTORISED PROPULSION on level ground lift rollers several centimetres onto central wheels in order to turn or push equipme
8. mbination Sealed Lead Acid Battery BATTERY LIFE at 20 C 100 depth of discharge 180 cycles 50 depth of discharge 540 cycles 30 depth of discharge 1200 cycles Recharge batteries after each use to increase battery lifespan Self Discharge at 20 C 1 month 3 3 months 9 6 months 15 How to recognise old batteries batteries charge and discharge quickly motors are slower caution Completely dead batteries do not work at all gt REMOVE FUSES BEFORE CHANGING BATTERIES 11 ELECTRICAL CIRCUIT DIAGRAM Electrical malfunctions can require intervention on the electric control circuit boards gt Contact a Klavier Roller technician before any intervention The diagram opposite can help the Klavier Roller technician guide you for trou bleshooting IMPORTANT before any intervention on the circuit board remove 25A fuses to avoid risk of short circuiting To access the circuit board disconnect connecting wire and remote control device remove the two screws on roller cover remove cover reconnect remote control device for testing the LED lights are visible for diagnosing the problem To remove the circuit board remove 25A battery fuses disconnect battery connectors pull circuit board upwards disconnect all wires and connectors in order to remove it to change a relay for example To reinstall the circuit board connect the 2 multiple terminals and then the single connectors a
9. ngaged attach transporting stirrup with straps unplug remote control device MANOEUVRING EMPTY ROLLERS load empty shoe or assemble the 2 rollers against each other with the 36 cm short lifting bars MAINTENANCE OF ROLLERS inflate tires regularly recommended pressure 4 bars lubricate lifting screws if necessary gt use Loctite 8103 GR135 only central wheel lowering can be interrupted if the central wheel lifting screws are not sufficiently greased ALUMINIUM RAMP AND PLYWOOD BOARDS A short staircase a bit longer even longer second plywood board short extensions half round supporting block first plywood board x Pe the boards must overlap the aluminium ramp does not touch the floor a upper contact plate For very long staircases remove lower board when freed place it above and so on rubber coated supports Using plywood board ALUMINIUM RAMP maximum vertical clearing height 1 30 m 4 3 with 2 metre 6 7 ramp 1 90 m 6 3 with 3 metre 9 10 ramp maximum authorised weight 750 kg 1650 Ibs ramp should have weight resting on either end do not lay down on a staircase adjust upper contact angle with appropriate knobs according to angle of slope in case of slippery ground lay a wooden board flat at end of ramp the aluminium ramp can be used at the start of a staircase WOODEN BOARDS FOR USE ON STAIRCAS
10. nt without using motors before any slope even slight stop and engage motors using roller handles gt do not force motor engagement handles in case of blocking activate propulsion motor until easy engagement occurs TURNING the rollers turn only when balanced on central wheels gt NEVER ATTEMPT TO TURN WHEN ROLLERS ARE ON ALL 6 WHEELS lift rollers onto central wheels before turning CLIMBING A STAIRCASE do not turn at the start of a climb when the central wheels are in the air drive rollers from the side or above do not stay underneath the equipment on a long staircase lift rollers slightly onto central wheels in order to correct trajectory the rollers do not climb in a perfectly straight line due to unequal weight of piano on each roller lower rollers onto all 6 wheels before arriving at top of staircase hold roller handles when at staircase landing DESCENDING put rollers on all 6 wheels lift central wheels use red button to begin descending always descend tail end first keyboard end above at the beginning of the descent hold roller firmly by the handle to keep it in a straight line and down the slope when the sled rubs against the edge of the staircase or on the top of the aluminium ramp FOR TRANSPORTING IN THE VAN check that rollers are on all 6 wheels lift central wheels with the motors bring rollers into contact with a stopping block at the front of the van and leave motors e
11. ollers reach end of travel 5 gt lowers rollers by raising central wheels stops automatically when rollers are on all 6 wheels 1 gt raises left roller by lowering left central wheel 3 gt raises right roller by lowering right central wheel 4 gt lowers left roller by raising left central wheel 6 gt lowers right roller by raising right central wheel Motorised propulsion select motor with button B 2 gt forward keyboard in front 5 gt backward 3 gt left turn going forwards 1 gt right turn going forwards 4 gt right turn going backwards 6 gt left turn going backwards raise rollers onto lowered central wheels before turning 7 red button gt motorised propulsion at reduced speed for descending slopes No motor is selected by default when remote control device is first connected Abeeping sound is emitted while motors are in operation The motors for the lifting bar and the central wheels stop automatically at end of travel After a few minutes without use the remote control device goes into security mode the indicator lights blink and the remote control no longer works Disconnect and reconnect remote control to reactivate The remote control can be connected to any one of the 4 available sockets 2 on each roller Disconnect remote control when not in use MOTORISED ROLLERS Important notice The rollers constitute a lifting and light transportation device that must be used wit
12. the rollers size 280 shoe 4 grooves the one furthest forward for a full sized piano the next one for a 3 4 size the third one for a 1 2 size and the last for a 1 4 size size 230 shoe 3 grooves the one furthest forward for a 3 4 size piano the middle one for a 1 2 size and the last one for a 1 4 size size 210 shoe 2 grooves the one furthest forward for a 1 2 size piano the other one for a 1 4 size USING REMOTE CONTROL DEVICE Indicator lights tail end lifting propulsion keyboard lifting central wheels The A and B buttons select the motor to be used These buttons have 2 positions The motor selected is shown by the red indicator lights The buttons 1 to 6 control the operation of the selected motors 2 and 5 control both rollers in unison 1 and 4 control the left roller only 3 and 6 the right roller only The red 7 button is used for descending only OPERATION To lift tail end of piano select motor with button A 2 gt lifts piano at tail end by raising lifting bar stops automatically when piano is fully lifted and lifting bar is blocked in rollers 5 gt lowers piano at tail end by lowering lifting bar stops automatically at end of travel To lift keyboard end of piano select motor with button A 2 gt lifts piano at keyboard end 5 gt lowers piano at keyboard end Central wheels select motor with button B 2 gt raises rollers by lowering central wheels stops automatically when r
Download Pdf Manuals
Related Search