ECOsense User Manual IR Transmitter
Contents
1. In case the AirCon or other devices have the same command for on and off then ECOsense can not be used on this device Testing IR commands manual Press setup button once will transmit IR command s one after the other the green LED will flicker once at the same time 3 Motion Sensor Timer Setup When Motion sensor STOP detecting human motion someone leave the room ECOsense activates a timer Once timer reach zero it will send the IR command s to power off The timer will restart counting whenever motion sensor detects motion again The time from the instant room is left empty till Power Off commands are sent is set by user using the Select Switch Off 60 30 15 min Select between 15 minutes 30 minutes 60 minutes and turn off The time selection depends on the activity in the room In case of office where there are many people located in the same area and there is a lot of movement then the timer can be set to 15 minutes In case of bedroom where there is less movement it is preferable to set the timer to 30 or 60 minutes to avoid false power offs 1 Low Battery Indication When the batteries are low the red LED flickers once each 60 seconds to indicate to change batteries as follows te J 2x AAA l Batteries below postage prepaid with proof of the date of purchase and an explanation of the defect or error The repair replacement or refund that is provided for above shall be the full extent of2. ECOsense User Manual About ECOsense Congratulations on purchasing the ECOsense energy saver With its elegant look and energy save feature you can now lower your electric cost and by doing so help saving the environment What is ECOsense ECOsense Automatically and Wirelessly Power Off Air Condition Heater amp TV in an empty room to Save Energy Key Features of ECOsense M Cut Electricity bills by 20 50 vM Automatically Turns Off Heating Air Condition and TV when room is left empty for a preset time 15 30 or 60 min M DIY No need wires or complex installation M Totally wireless simply fix on wall or ceiling M Best seller product for the current economy v Effective solution for Green Environment M Low Cost device with High Savings Specification uM Voltage 3VDC 2 AAA batteries v Size 60 x 60 x 15 mm M Detecting range lt 6M at 360 M IR transmitting range lt 6M M IR transmitting direction 1 in front and 1 on side M IR learning code 2 IR commands of most devices stored in Flash memory also if no battery vM Mounting optional Ceiling or Wall with screws or sticker m Indoor use only 5 to 40 c up to 85 relative humidity What s included A A T ECOsense device 2 AAA batteries User Manual Red amp Green LED s e li I eee ae Motion Sensor Q me p Timer select switch PX Z IR Receiver am
3. Seller s liability with respect to this product For repair or replacement during the warranty period call EKON s customer service to receive Return Authorization number properly package the product with the Return Authorization number clearly printed on the outside of the package and send the product along with all other required materials to 1088 Xinjinqiao Road Room 1218 1219 Building A Xin Pudong District Shanghai 201206 China
4. ips of location in room M Locate as close as possible to where people are most present in the room to ensure no false turn offs M ECOsense has 2 IR transmitters make sure at least one is facing IR device IR Transmitter M Do not place close to window or direct sunlight M Do not face towards moving objects such as Curtains in the wind hang up balloons etc M Motion sensor detects pets which will cause the timer to recount and so will delay the power off 2 IR command Setup A Press Setup button for 5 sec without relaxing till red LED turns on enter setup mode Press Setup Button 5 seconds IR receiver Green LED will flicker once if the process is IR received successfully or it will flicker 5 times if failed C Send 2 Off command from TV or other device to IR receiver If IR received successful then ECOsense will exit Setup mode Red LED goes off This step is optional if only 1 command is required press the Setup button again to exit D If no command is send within 15 seconds it will exit setup mode E Pressing setup button 10 seconds will erase all IR commands Notes about IR learning Most air condition have the same button for Power On and Power Off but in fact they send different commands In that case turn the AirCon ON so the LCD displays the temperature and then press the power button again facing the ECOsense
5. p System Disabled x Setup and IR Transmitters Test Button Limited Warranty Seller warrants to the original consumer purchaser of this product that for a period of one year from the date of purchase this product will be free from defects in material and workmanship and will perform in substantial conformity to the description of the product in this User s Manual This warranty shall not apply to defects or errors caused by misuse or neglect If the product is found to be defective in material or workmanship or if the product does not perform as warranted above during the warranty period Seller will either repair it replace it or refund the purchase price at its option upon receipt of the product at the address 1 Mounting Wall or Ceiling ECOsense should be implemented in the same room where the IR device air condition TV etc is located with direct eye contact between the IR transmitter of ECOsense and the IR receiver The maximum distance between ECOsense and the IR device is 6 meters depend on the IR device manufacturer ECOsense should be fixes on the wall or the ceiling of the room by Double side tape or 2 Screws ECOsense should be located in a central location where it can sense people movement in all positions of the room The motion sensor can detect human body movement within a range of maximum 6 meters a lo Motion 7 X IR Devices s Sensor Max 6m Max 6m XN N N N i ECOsense t
Download Pdf Manuals
Related Search