ASLP3507 - Autec-VLT Automotive Equipment
Contents
1. ES UNPACK THE GOODS AND CHECK FOR POSSIBLE DAMAGE BEFORE INSTALLING THE LIFT A ONLY SKILLED TECHNICIANS APPOINTED BY THE MANUFACTURER OR AUTHORISED DEALERS MUST INSTALL THE LIFT FAILURE TO DO SO MAY RESULT IN DAMAGES TO PERSONS OR OBJECTS FOR WHICH THE MANUFACTURER CANNOT BE HELD RESPONSIBLE The lift must be installed according to the specified safe distance from walls columns other machinery etc The room must be at least 4500 mm in height The minimum distance from walls must be 2000 mm see diagram The lift may be positioned on any type of floor as long as it is perfectly level and of adequate resistance min 250 kg cm INSTALLATION PROCEDURE Check for availability of power supply Positioning of lift Hydraulic connections Electrical connections Fixing of lift Initial running Use suitability ee et eee ll AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl Ce User Manual AUIES VLT ASLP3 507 Issued BG May 2010 1 CHECK FOR AVAILABILITYF POWER SUPPLY First of all ensure that the power supply is equipped by a magnet thermic switch 380V 16A with protection fuses with suitable protection devices conforming to safety regulations and that the maximum distance of the electrical connections and the hydraulic connection2. Fax 31 348 475104 Internet www autec nl E mail info autec nl
3. 4 months Oil must be completely changed at least every 3 years WARNING Used oil is a highly polluting product Always dispose of used oil according to laws of the country where the lift is installed WARNING Brake oil must be immediately removed as it is immediately corrosive for the varnish The piston stem must be protected from impurities that may cause damages or prematurely wear out or even break the internal gaskets of the piston DEMOLITION Only authorised and specialised technicians should proceed with the demolition of the lift Follow all precautions as specified in the chapter on Safety Metallic parts can be scrapped as scrap iron All other materials must be disposed of according to laws of the country where the lift is installed For fiscal purposes all demolition operations must be properly documented according to laws of the country where the lift is installed at the time of demolition 19 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands C Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl User Manual AUES VLT ASLP3 50 7 Issued BG April 2010 CHAPTER 7 TROUBLESHOOTING 5 Warning It is important to follow all precautions in the chapter on Safety when identifying and searching for faults and carrying out subsequent repairs MANUAL LOWERING In ca
4. Issued BG May 2010 The lift model ASLP 3507 is delivered assembled and packaged as follows N 2 platforms Pl P2 complete with bases and scissors and positioned on wooden pallets with wooden shims wrapped in pluriball plastic and closed with metal clips and relative gaskets N 1 control unit wrapped in pluriball plastic N 1 carton box containing the contol unit set of short ramps on floor version complete with tube cover canals or a set of space covers and four rubber pads H 40 set of space covers N 1 set of short or long lifting ramps complete with tube cover canals For single deliveries up to 3 units the articles described above long ramps excluded are placed one on top of the other and packed onto platforms with metal clips and relative seals see picture 1 For multiple deliveries over 3 units the packaging for the platforms remains the same whilst all other articles are positioned and packaged onto europallets picture 2 PACKAGING SIZES mm FOR SINGLE DELIVERIES UP TO 3 UNITS A LENGTH B WIDTH C HEIGHT MODEL A B C WEIGHTKG ASLP3507 1700 660 950 TRANSPORT Pict 2 The packages described in page 5 can be lifted and transported using forklifts cranes or other lifting systems of adequate capacity Upon receiving goods verify that no damage has been caused and that there are all parts indicated on the checklist Any damages and or missing parts must be immediately reported to
5. on the lift A 8 Entering the vehicle and or starting the engine when the lift is raised is strictly forbidden G 9 Never leave objects under the vehicle or scattered around it whilst lowering the lift 9 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl User Manual Allee VLT ASLP3 507 Issued BG May 2010 A AG A A 10 Keep the area around the lift clean and remove any oil spills to avoid the risk of slipping 11 Never use jets of water steam varnish or solvents in the lift areas around the lift and the control unit 12 Non suitable lighting may be risky Ensure all areas next to the lift are well lit in a uniform manner 13 Climbing on the platform when lifting the vehicle or when it has already been raised is strictly forbidden 14 Any use of the lift other what it has been designed for may cause serious accidents to people and objects in its proximity 15 The tampering of safety devices is strictly forbidden 16 Never exceed the maximum lifting capacity 3500 kg Check weight of vehicles that are loaded 17 In case of malfunction stop the lift and block the on off button by using a lock Only skilled technicians should be allowed to restart the lift Make sure the main power supply has been switched of
6. the deliverer and subsequently reported and documented to the manufacturer PACKING REMOVAL All wooden packaging and pluriball plastic can be recycled Total elimination of the packaging is possible in compliance with the laws of the country where the lift is installed AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl Ce User Manual AUtee VIT ASLP3 507 Issued BG May 2010 CHAPTER 2 MACHINE DESCRIPTION ASLP3507 is a double scissor lift with free wheels designed and constructed for lifting cars of weight not exceeding 3500 kg It is equipped with extensions on platforms for also lifting longer vehicles The structure of the lift 1s as follows A BASE B SCISSORS PLATFORM C CONTROL UNIT MOBILE STRUCTURE FIXED STRUCTURE Pict 3 BASE This is the fixed part of the lift equipped with floor fixing holes SCISSORS PLATFORM This is the mobile and lifting part of the lift It is made up of a series of arms and the upper platform all fixed together by rotating pins on self lubricating bushes The mobile parts move on Teflon sliding blocks AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands Tel 31 348 477000 Fax 31 348 475104
7. to The P1 levelling microswitch is positioned incorrectly Remedy Check the position of the microswitch on its support Replace the micro if faulty B The magnet of the levelling valve is not excited Remedy Check if the valve opens by connecting 24V directly onto the magnet Check the functioning of the electric card and the connection of cable between magnet and the card C The levelling valve on the hydraulic block remains closed Remedy Check if electrovalve is blocked Pull it out from the block and verify if inner cylinder is free to move using a small pin Replace the valve if the pin remains blocked SYMPTOM 7 The P2 platform is fully lowered while the P1 platform remains lifted POSSIBLE CAUSES 7 A The lowering valve remains closed due to The P2 levelling microswitch is positioned incorrectly Remedy Check the position of the microswitch on its support Replace the micro if faulty B The magnet of the valve is not excited Remedy Check if the valve opens by connecting 24V directly onto the magnet Check the functioning of the electric card and the connection of cable between magnet and the card C The lowering valve on the hydraulic block remains closed Remedy Check if electrovalve is blocked Pull it out from the block and verify if inner cylinder is free to move using a small pin Replace the valve if the pin remains blocked 22 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrie
8. 810 i co hj iD 101 FOO 1980 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl Ce User Manual ASLP3507 AUZE VLT Issued BG May 2010 TECHNICAL CHARACTERISTICS Electric hydraulic functioning Hydraulic synchronism of platforms Safety hydraulic circuit in case of accidental breakage or failure of hydraulic tubes Hydraulic safety using parachute valve Overload security valve Lowering control valve Manual lowering device in case of power failure Acoustic light signal for final lowering phase Inductive proximity sensors Low voltage controls 24V TECHNICAL DATA e Capacity 3500 kg e Maximum height 1910 mm e Platform length 2000 mm when using extension e Platform width 640 mm e Lifting time 50 sec e Lowering time 45 sec e Motor 3 PH 240 400 V 3 kw 50 HZ e Noise level lt 74 db e Exercise temperature 10 50 e Maximum pressure 300 bar e Maximum amperage 8 A e Weight 850 900 kg The ASLP3507 lift has been designed and built for lifting vehicles in closed areas Any other use is not advised and the lift s especially unsuitable for the following uses Ce washing painting hoisting lifting people pressing AUTEC VLT Automotive Equipment divisie van Autec Hefbrugge
9. ASLP3 507 Issued BG May 2010 HYDRAULIC DIAGRAM a2 B2 B1 KIIK pet LS ar z LIS SL 18 SUCTION FILTER z PUMP 5 LT cm s FULL FORCE VALVE MOTOR 3KW UNIDIRECTIONAL VALVE LOWERING ELECTROVALVE LEVELLING ELECTROVALVE PARACHUTE VALVE HOLE 0 5mm 0 BRAKE PISTON ae eee ee 14 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl Ce User Manual ASLP3507 AUZE VLT Issued BG April 2010 4 ELECTRICAL CONNECTION 380 qe F E Ti 70 VA ef F I Cl un m Ti IN MAIN SWITCH F1 FUSE 5x20 1A Z1 SAFETY MOTOR Y1 LOWERING ELECTROVALVE TA TOUCHPAD FB PROXIMITY SWITCH HIGH STROKE END 3 PROXIMITY SWITCH HIGH STROKE END 4 PROXIMITY SWITCH OF LEVELLING BROWH BLACK __B BLUE E EL EL Ke MOTOR CONTACTOR TRANSFORMER 70VA HIGH STROKE END EXCLUSION LEVELLING ELECTROVALVE LED RELE 24V DC 15 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands C Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl User Manual AUIES VLT ASLP3 50 7 Issued BG April 2010 Warning Before working inside the control unit for connecting the electric supply o
10. Internet www autec nl E mail info autec nl Ce User Manual AUIES VLT ASLP3 507 Issued BG May 2010 CONTROL UNIT The unit s made up of a metallic box that contains all electrical hydraulic and pneumatic functioning parts of the l ft The controls are placed on the upper part of the unit are of 24 V voltage and of the dead man type There is one main control switch and a touchpad Pict 4 MAIN SWITCH LIFTING PUSH BUTTON LOWERING PUSH BUTTON LED RE ACTIVATION BUTTON POWER LED Main switch The switch can be padlocked to prevent the use of the lift during the maintenance Lifting push button When pressed motor and lifting mechanism are operated Lowering push button When pressed lowering electrovalves are operated Led It flashes during the final lift lowering at the same time with the acoustic transponder Re activation button This button restarts the lowering button 2 for the final phase under 250 mm Power led it indicates the presence of electricity Nn amp WN AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl Ce User Manual Vie VIT ASLP3 507 Issued BG May 2010 OVERALL DIMENSIONS Incl 4 rubber pads 2000 Inkl 4 Gummilbl cke ind 4 rubber blokken 1808 1
11. User Manual lec VLT ASLP3 507 Issued BG May 2010 ASLP3507 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands C Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl User Manual AUtee VIT ASLP3 507 Issued BG May 2010 CONTENTS FIRST PART CHAPTER 1 INTRODUCTION PACKING TRANSPORT CHAPTER 2 MACHINE DESCRIPTION page 5 CHAPTER 3 SAFETY page 9 CHAPTER 4 INSTALLATION page 11 CHAPTER 5 OPERATION page 18 CHAPTER 6 MAINTENANCE page 19 CHAPTER 7 TROUBLESHOOTING page 20 CHAPTER 8 ACCESSORIES page 23 CHAPTER 9 DECLARATION OF CONFORMITY page 24 SYMBOLS A ee rr ee HAZARD DANGER amp en PROHIBITED Ennn WARNING Follow the instruction given by the messages preceded by a safety alert symbol AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl Ce User Manual AUES VLT ASLP3 507 Issued BG May 2010 CHAPTER 1 INTRODUCTION PACKING TRANSPORT INTRODUCTION This instruction manual has been created for workshop personnel using lifts and for ordinary and extraordinary maintenance technicians The manual must be read before proceeding wi
12. c test some cycles of lifting and lowering have to be carried out with a weight equal to the nominal capacity increased of the 10 17 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands C Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl User Manual AUIES VLT AS LPS 50 7 Issued BG April 2010 CHAPTER 5 OPERATION DRIVING SEQUENCE 1 Greater weight 2 lower weight extension piston Pict 8 Before lifting lowering vehicles on the lift ensure that the two platforms are completely closed and that extensions have been inserted Position the vehicle so that greater weight is on the opposite side of the extension Place the vehicle onto the lift very slowly and make sure that the vehicle is properly positioned on the platforms Position rubber pads into the lifting points as indicated by the manufacturer of the vehicle Press the lifting button until the required height is reached and the lowering button to bring the platforms back down The lift will automatically stop at approximately 30 cm from the ground The acoustic light signal will be then activated for the last lowering phase During the initial operations of the lift cracking noises may be heard This is due to the natural settlement of mechanical parts and will eventually stop CHECKS Always carry out the following checks when op
13. e cycle of operations at least another 2 times 16 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands C Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl User Manual Allee VLT AS LP3 50 7 Issued BG April 2010 6A PISTON BRAKE REGULATION Lifts are equipped with a braking system which operates in the last 10 cm of travel In case the two platforms won t go down synchronized in the last 10 cm please follow these steps 1 Check which platform is the slower in lowering with no load on 2 Put the platforms at an height of 20 30 cm 3 Unscrew the blocking nut of the regulation screw on Pl piston of the slower platform see picture 4 Check the synchronism of the platforms in the last 10 cm of the travel Work if necessary on the regulation screws of the brake screwing will reduce velocity unscrewing will increase it 5 Screw the nut 6 Press the lowering button and check the synchronism of the platforms repeat the operation if necessary until a perfect synchronism is reached 7 USE SUITABILITY Follow with attention the indications in order to avoid damages to people or things and to the same lift Once effectuated the fixing of the lift proceed with the static and dynamic tests For the static test apply a weight equal to the nominal capacity increased of the 25 For the dynami
14. erating the lift e Carefully monitor the lift and its load during lifting lowering operations e Make sure the acoustic light signal works correctly during the lowering main lift e If the platforms are not level during these first operations repeat air bleeding procedures with the pistons at their maximum height 18 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands C Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl User Manual Allee VLT AS LP3 50 7 Issued BG April 2010 CHAPTER 6 MAINTENANCE WARNING Only authorised personnel must carry out maintenance During maintenance operations it is important to follow instructions in the chapter SAFETY and ensure that all steps are taken to avoid accidental starting of lift PERIODIC MAINTENANCE In order to keep the lift in peak condition it is important to carry out periodic maintenance The manufacturer s guarantee does not cover failure to do so e The lift must be cleaned at least every 30 40 days Do not use aggressive chemical products or high pressure washing guns for cleaning e Lubricate the sliding blocks and relative roller slideways periodically with grease e Periodically check safety devices for proper working conditions e Check high pressure hydraulic tubes once a year e Check the oil level inside the tank every 3
15. f before repairing and servicing the lift SAFETY DEVICES ANTI SHEARING AND FOOT SAFETY The lift 1s provided with a safety device that automatically stops lowering at approximately 40 cm from the floor An acoustic light signal is also activated during the final part of lowering HYDRAULIC SAFETY This safety device is made up of parachute valves positioned inside the pistons The valves automatically block the lowering of the lift in case the hydraulic tubes are broken or accidentally cut DEAD MAN SAFETY DEVICE The car lift s fitted with a dead man control device Releasing push button controls situated on the console of the control unit immediately stops lowering and lifting operations DOUBLE CIRCUIT HYDRAULIC SAFETY The lift has an independent double hydraulic system Each circuit has the capacity to support the load but not to raise it This allows for positioning and or lowering the load even when there is a failure in one of the two circuits OVERLOADING SAFETY The lift is fitted with a maximum valve for overloading This valve does not allow for lifting when the load has exceeded maximum capacity Ce 10 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl User Manual AUIES VLT ASLP3 507 Issued BG May 2010 CHAPTER 4 INSTALLATION
16. instructions for step 1 SYMPTOM 4 The lifting button is pushed but lift stops 21 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands C Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl User Manual Allee VLT AS LP3 50 7 Issued BG April 2010 POSSIBLE CAUSES 4 A If the lift moves when pushing the yellow exclusion button and the lifting button simultaneously the lifting limit switch is faulty or incorrectly positioned Remedy Check the correct position of the cam and the functioning of the micro switch Replace if faulty The micro should intercept the cam when the platform is at maximum height B The lift does not move when pushing the yellow exclusion button and the lifting button simultaneously Remedy Follow instructions in step 1 SYMPTOM 5 The acoustic signal is activated during the lowering phase but the lift has not yet reached 30 cm from the floor POSSIBLE CAUSES 5 A The microswitch for the photocell cut out is faulty or incorrectly positioned Remedy Check the correct position of the cam and the functioning of the micro Replace if faulty The micro should intercept the cam when the platform is about 30 cm from the floor SYMPTOM 6 The P1 platform is fully lowered while the P2 platform remains lifted POSSIBLE CAUSES 6 A The levelling valve remains closed due
17. ive electric card Remedy Check if relays and leds are activated when pushing buttons on the touchpad D Uncertain connections between electric card and contactor motor protector valves Remedy Check connections between electric card and contactor motor protector valves Replace faulty parts E Photocell does not work Remedy Check that photocell and relative connections are correct Replace photocell 1f faulty F Lifting limit switch does not work Remedy check lifting limit micro and ensure connections are correct Replace if faulty SYMPTOM 2 When pressing the lifting button the lift does not move the motor runs POSSIBLE CAUSES 2 A Counter clockwise rotation Remedy Invert the power supply phases of the motor if necessary B Lack of oil Remedy Check there is enough oil in the tank C The lowering electrovalve on the hydraulic block remains open Remedy Check if opening is due to a mechanical fault or magnet stimulation Replace faulty parts D Maximum pressure valve broken Remedy Tighten valve fully and turn back 1 and turns Retest the lift and replace valve if problem persists E Flexible hose connecting the pump and the hydraulic block is broken or loose Remedy Check the hose in the tank Replace if broken SYMPTOM 3 The lowering button is pushed but lift does not move POSSIBLE CAUSES 3 A Follow instructions for step 1 lifting limit switch excluded Remedy Follow remedy
18. n bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl User Manual AUIES VLT ASLP3 507 Issued BG May 2010 CHAPTER 3 SAFETY GENERAL RULES Read this chapter carefully as it contains important information concerning the safety of the operator and risks that may be incurred with incorrect or improper use of the lift Operating and maintenance personnel must observe workplace accident prevention legislation in force in the country where the lift is installed Pict 6 5 1 During lifting or lowering operations the lift must be operated only in the reserved control area as shown in the diagram A 2 Stopping or passing within the danger area when the lift is working or already raised is strictly forbidden Only the operator may stay under the lift when it is raised E 3 The operator must ensure the danger area is clear when lifting or lowering the lift 4 Never use the lift without protection or when safety devices have been switched off or tampered with E 5 When raising a vehicle use the supplied rubber pads on the correct support points as advised by vehicle manufacturer E A 6 Switch off the engine and engage the parking brake after placing the vehicle on the lift Remember to disengage the gear by placing the gearshift to neutral AN 7 To prevent vehicle from falling make sure it is properly placed
19. r for the repair of faults make sure the main power supply has been disconnected to avoid being electrocuted 5 FIXING OF LIFT After making electrical and hydraulic connections make sure the bases are perfectly parallel It is now possible to fix the lift to the floor using the bases as templates Drill a hole in the floor using a 16 mm bit to a depth of approximately 150 mm Clean the holes and place the proper inserts and complete by tightening with bolts 6 INITIAL RUNNING 5 Warning Only skilled and authorised personnel should carry out the following operations Follow instructions carefully in order to prevent damage to lift or injury to persons Ensure that the operating area is clear After positioning the lift and connected the electric and hydraulic supplies proceed with initial running operations Press up button until arriving at the height established by the microswitch for max height Open the top cover of the power unit push together the up button and the red button exclusion of the microswitch of amx height see picture 1 placed beside the electric board until the complete rise of the platforms Press again the buttons up and microswitch exclusion max height in the way to fill the hydraulic circuit therefore allowing the bleeding of the air from the pistons In the moment in which from the unload tube white comes out only oil the operation of bleeding is concluded Take the lift to ground Repeat all th
20. s from the control unit must be 3 metres Open the front door of the control box and connect the power supply cable to the terminal 2 LOCATION OF THE LIFT Position the lift using a forklift crane or other suitable means To open the scissors raise the platform by at least 70 cm as indicated in picture Place a wooden shim under the platform to avoid closing the scissors Proceed by moving and then positioning the vehicle onto the lift as shown in picture 7 Eliminate the possible slight floor level differences max 7mm with the use of metallic thicknesses ak d I H min ed u be en F u t i pi nn T en f ns ee i T i pe OE BE z Per r u a iat p Ta AA awe el ma 2000 rlr er i a i a Pe E i er i a Li ol i en u rr I Fi a7 nag PERM ZH u VEHICLE ENTRY mun BON max 00 Pict 7 12 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl Ce User Manual ASLP3507 3 HYDRAULIC CONNECTIONS BLEEDING SYSTEM Oil tank AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl Ce User Manual AUIES VLT
21. se of power failure faults in hydraulic electrovalves or electrical system failure it is possible to lower the lift manually 5 Warning Manual emergency lowering must be carried out exclusively by authorised and trained personnel Manual emergency lowering must be carried out as follows Pict 9 Pict 10 Check that there are no obstacles blocking the lowering operations It will not be possible to subsequently raise the lift without removing obstacles At first press only the EA electro valve see picture 9 and then keep on pressing it together with the EO electro valve see picture 10 At this point the lift will slowly start to go down ES Warning Check the danger area during operation Block the manual operators in case of danger or to simply stop lowering 20 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands C Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl User Manual Allee VLT AS LP3 50 7 Issued BG April 2010 TROUBLESHOOTING SYMPTOM 1 When pressing the lifting button the lift does not move the motor does not run POSSIBLE CAUSES 1 A Lack of power supply to the electric card and the transformer Remedy Check the relative fuse Replace if fuse is blown B Touchpad does not work Remedy Check touchpad with a tester and replace if faulty C Defect
22. terrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands C Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl User Manual Allee VLT AS LP3 50 7 Issued BG April 2010 CHAPTER 8 ACCESSORIES The following accessories may be supplied upon request Supplementary rubber pads set H 40 mm BA RB40 Supplementary rubber pads set H 60 mm BA RB60 Supplementary rubber pads set H 80 mm BA RB80 Floorextensionset for increased lifting height 135mm BA A8H ASLP3507 Drive on off ramps long extreme low cars BA A8L ASLP3507 23 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands C Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl User Manual Allee VLT ASLP3 507 Issued BG April 2010 CHAPTER 9 DECLARATION OF CONFORMITY AUTEC Hefbruggen b v Vlasakker 11 NL 3417 XT Montfoort Nederland Hereby declares that the lift ASLP3507 To which this declaration is related conforms with the following European directives 2006 42 CE It also declares that the following European rules have been respected EN 1493 CE Certificate number 0062 150X0454 06 06 24 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands C Tel 31 348 477000
23. th operating the lift and contains important information for the safety of personnel the safety of the lift the safety of lifted vehicles This manual is an important part of the lift and must be kept where it is easily accessible for consultation and we recommend particular attention in reading the chapter on safety The lift ASLP3507 has been designed and built as required by EUROPEAN RECOMMENDATIONS EEC 2006 42 CEE EUROPEAN RULES EN 1493 All operations of the lift must be carried out by skilled and authorised personnel especially operations of transportation assembly installation maintenance overhaul moving dismantling etc The manufacturer cannot be held responsible for damages to persons vehicles or objects caused by improper use of the lift er Carefully read this instruction manual before using the lift er The lift must be used only for lifting vehicles up to the specified capacity Improper use of the lift is forbidden er Disconnect the lift from the main electric supply before carrying ordinary and extraordinary maintenance operations er The lift must be installed according to instructions PACKAGING C 0mm Pict 1 AUTEC VLT Automotive Equipment divisie van Autec Hefbruggen bv Industrieterrein IJsselveld Vlasakker 11 3417 XT MONTFOORT The Netherlands Tel 31 348 477000 Fax 31 348 475104 Internet www autec nl E mail info autec nl Ce User Manual AUIES VLT ASLP3 507
Download Pdf Manuals
Related Search