instruction manual
Contents
1. USER S MANUAL version 1 1 AWST 6000 WIRELESS MOTION SENSOR AWST 6000 WIRELESS MOTION SENSOR Picture ofthe 1000 A Motion sensor E Switch on signal not included B Removable switch F Range switch plate G Light sensitivity switch C Battery compartment D Time switch off AWST 6000 WIRELESS MOTION SENSOR 1 Remove the front with the sensor and the wall plate from the base A If necessary use a screwdriver to carefully pry off the front A recess is provided on the underside of the front for this purpose 2 Mount the product in the desired location A The arrow must point up A Place the product at a height of approx 1 5 metres see Remarks for the influence of the height on the detection range AWST 6000 WIRELESS MOTION SENSOR 3 Insert the batteries with the and poles facing the correct direction LEARN 2M 10M DEL SET 4 Set the light sensitivity switch to M or L M Sensor works in areas with little light or in the afternoon 15 to 25 Lux L Sensor works in dark areas or late in the evening 0 to 15 Lux A Set the switch to H if this product is used in combination with a receiver of type doorbell chime AWST 6000 WIRELESS MOTION SENSOR LEARN SM10M DEL SET E 5 Activate the automatic search mode of the 6 Slide the LEARN switch to SET To confirm rec2. and or receivers e For all practical purposes the transmission code is unique 1 out of 67 million and is pre programmed at the factory You cannot change the house code e This product can only be used with COCO receivers that automatically program themselves with the transmission code The type designation of these products always begins with an A e Consider objects such as trees or bushes within the detection range When moved by wind or birds the detector will respond to the unintended motion e To prevent interference avoid placing multiple products close to each other The minimum distance between units should be approx 50 cm e Deleting the transmitter code from a receiver Repeat 5 6 In step 6 slide the LEARN button to DEL to confirm the receiver switches on and off two times e Ifthe product does not work Check the correct placement and or function of the batteries replace if necessary Check step for step whether this product and the receiver are configured properly A Safety instructions e Never use COCO products for life support systems or other applications in which equipment malfunctions can have life threatening consequences e Do not expose this product to excessive heat direct sunlight or moisture e Remove the battery from this product if it will not be used for an extended period e Do not attempt to repair this product If the product is damaged or if you are in doubt about the proper op
3. eguirements and other relevant provisions of the applicable European directives The Declaration of Conformity DoC is available at www coco technology com If possible submit this product for recycling after use Do not dispose of the product with household trash AWST 6000 WIRELESS MOTION SENSOR CoE Warranty and copyright This device is covered by a two year warranty that begins on the day of purchase Visit www coco technology com warranty for additional information Reprinting of portions of this manual without permission from Pan Trade International B V is expressly prohibited AWST 6000 WIRELESS MOTION SENSOR pit PAN TRADE INTERNATIONAL B V BOX 126 4760 AC ZEVENBERGEN THE NETHERLANDS www coco technology com Declaration of Conformity Pan Trade International BV declares that the COCO product model type designation AWST 6000 WIRELESS MOTION SENSOR item number 74013 is in compliance with the essential reguirements and other relevant provisions of directives amp 1999 5 EC EMC 2004 108 EC and LVD 2006 95 EC and is compatible with the standards EN 300 220 1 3 EN 55015 EN 301 489 1 3 and EN 60950 Manufacturer Authorised representative ANS Hoekstra managing director Zevenbergen 2008 01 30
4. eiver see the corresponding manual the receiver switches on and off two times A This product only works with receivers with a product code that begins with A A The figure shows the AC 1000 not includea AWST 6000 WIRELESS MOTION SENSOR 7 Set the range switch to the desired range see Remarks for more information 8 Set the time for switching off As soon as no more movement is detected the transmitter will automatically send an off signal after 5 seconds 1 minute 5 minutes or 10 minutes A The switch time does not work for a receiver of type doorbell chime AWST 6000 WIRELESS MOTION SENSOR CO JE 9 Place the wall plate back on the base 10 The detection range is maximum 80 and minimum 20 Remove or reposition the screens to The front only fits in one direction The sensor adjust the angle should be slightly above the centre A The sensor screens can be reduced in size if desired AWST 6000 WIRELESS MOTION SENSOR Remarks A Placement and detection range F F wil 3 i AWST 6000 WIRELESS MOTION SENSOR CO A Reminders e This motion sensor is a transmitter for operation of one COCO receiver independently or multiple receivers simultaneously e This product must be used in combination with at least one COCO receiver not included e The wireless system can be expanded indefinitely with other COCO remote controls
5. eration take the product back to the place of purchase e Do not use the product in damp areas Clean the device with a clean cloth AWST 6000 WIRELESS MOTION SENSOR co E Power When some time has passed if a receiver no longer responds when the product is used replace the batteries e Use only 1 5 Volt AAA alkaline batteries e Do not throw the battery into an open fire e Respect the local regulations when disposing of batteries A Wireless e This product works using a radio signal that passes through walls windows and doors The range is maximum 75 metres in the open air The range indoors is strongly influenced by local conditions such as concrete glass and metals On average the indoor range is approximately 30 metres e New double glass often includes a thin metallic layer This type of glazing HR glass allows most visible light to pass through but has a negative impact on radio signals If there is HR glass between the transmitter and receiver you should expect a significant reduction of the range of the wireless signal e This product operates at a frequency of 433 92 MHz It complies with the essential requirements and other conditions of R amp TTE Directive 1999 5 EC and can be used in all EU countries e There may be restrictions on the use of this device outside the EU If this device is used outside the EU check whether the device complies with the local directives This product complies with the essential r
Download Pdf Manuals
Related Search