Home

Instructions for use Sunray 2000 LED Lighting

image

Contents

1. 5 Installing Batteries 1 ae 6 Removing Batteries eae 6 Mounting Battery eee E eae 6 Mounting Arm to 7 Mounting Arm to Light er 7 Removing Arm from Light 5 7 Connecting Battery to Light Head 7 8 Light Operation with Bluefin 2 00 e cece eee 8 Light Operation with Stingray Housing 2 2 8 Light Operation with Other Housing Brands ee eee 9 Post Dive Cleaning vavws iv dene 9 SO 9 Other Maintenance cacy lt o4 ged Sng ha 9 Return Products for ae 10 Contact Light amp Motion 10 Important Caution Getting Started Pictured below are the components of the Sunray 2000 LED lighting system Take a moment to familiarize yourself with each part for later identification and use Sunray 2000 LED Light System 3 Light Arms Pod Locker Charger and NiMH Batteries Electrical Cord Sunray 2000 LED Light Heads Battery Pods Charging Batteries rz Due to shipping batteries charge states will vary It is recommended that you charge your batteries when they are received The charger can accept an electrical range of 100 240v and 50 60hz 2 The charger has two LED lights Left LED illuminates when charging a NiMH battery
2. Monterey CA 93940 831 645 1525 Fax 831 375 2517 www uwimaging com 905 0281 A
3. EAN THE CONNECTORS Pay special attention to the condition of the connectors at the end of the cables Equally important is the female receptacle in the battery pod These metal connectors should shine like a new penny Apply a light film of O ring grease to cables and connectors to prevent premature degradation Returning Products for Care We highly recommend a factory annual service to maintain proper operation of your Sunray 2000 LED lights Before returning your Light amp Motion product for care please call or email our service department for a RMA number 2 Ship your product pre paid freight with the return number printed on the outside of the box It is recommended that you keep your shipper s tracking number until the product is returned to you Warning Do not ship your camera inside the housing Shipping companies may drop your system from up to three feet which could damage your camera Contact Light and Motion Sales amp Support Phone 831 645 1525 Fax 831 375 2517 Mail Light amp Motion 300 Cannery Row Monterey CA 93940 E mail support lightandmotion com World Wide Web European Service Center www uwimaging com Fish Eye Productions Attn Steve Mawle Unit 5 Vanguard Trading Estate Britania Rd Chesterfield S402TZ England Tel 44 0 1246 216016 Fax 44 0 1246 563785 sales fep co uk service fep co uk www fep co uk LIGHT amp MOTION 300 Cannery Row
4. Owner s Manual Sunray 2000 LED Lighting System LIGHT amp MOTION www uwimaging com Standard Warranty Light amp Motion provides a limited warranty to the original purchaser for the Sunray 2000 LED Light System against all defects in original workmanship and material under normal use and service for one year from the date of purchase with the following exceptions Batteries are warranted for 90 days and battery chargers are only warranted for use in the US and Canada Using a battery charger in conjunction with a voltage converter is NOT considered normal use and chargers will not be warranted under such conditions Light amp Motion will not be liable for any further loss damages or expenses including incidental or consequential damages directly or indirectly arising from the sale or use of this product Products not manufactured by Light amp Motion such as strobes and strobe arms are not covered under the Light amp Motion warranty These products are covered by the Terms and Conditions set forth by their respective manufacturers Welcome Congratulations on your purchase of the Sunray 2000 LED light system Please inspect the packaging of your product to verify that there was no damage during shipping Periodically refer to http www uwimaging com for instruction revisions Caution Caution Caution Caution To increase your enjoyment and the life span of your equipment please take an extra min
5. Right LED is illuminated orange when charging and green when the charging cycle is complete 3 attach charger to battery align arrow on charger connector with arrow on battery and push together until connectors seat Refer fig pra Charge time for the Multi Chem fast charger is 1 5 hours 5 Installing Batteries 2 3 Slide the battery back into the pod with the contact end inserted first so that the connector will align with the socket inside the pod Refer fig Service the O rings See O ring maintenance Replace the front cap onto the pod Insure that the removal strap attached to the battery does not interfere with the seal when the end cap is attached to the pod Turn the knob on the end cap clockwise 1 8 turn until it stops The endcap will now be locked into place Note that endcaps are specific to the left and right pods Removing Batteries 2 3 Rotate latch at the front of the pod counter clockwise 1 8 turn or until it stops Pull the front cap off the pod Pull the battery from the pod using removal strap Mounting Battery Pods Battery Pods be mounted prior to installing batteries into pods Remove the rear plate or monitor back of the housing Slide battery pods into channels along bottom of housing Refer fig 2 Insert Pod Locker between the pods and tighten using 1 8 allen wrench DO NOT OVER TIGHTEN Refer fig 3 on next page Mounting Removing Light Ar
6. ms To attach the arm to the base place the arm on the base squarely gently pushing down and rotating arm until you hear a audible click Refer fig 4 Remove arm by gently lifting the ring at the base of the arm upward with your thumb and forefinger while rotating the arm itself The arm will release after 30 degrees of rotation in either direction Refer fig 5 Mounting Light Arms to Light Heads Align top of arm with arm light head base and press FIRMLY together Arm should snap into position Refer fig 6 Removing Light Arms from Light Heads To remove light head from arm break the arm at the upper most joint Connecting Batteries to Light Heads Plug in the light connectors on pod 2 Tighten the locking sleeves by rotating clockwise until tight 7 Light Operation After initial power up the LED Receiver will flash a green light This indicates the battery pod is ready to receive IR signals from the housing IR controls are only available with housings that feature Smart Grips Operation with Bluefin Housing Sunray LED lights can be operated either by the Pod Power Button or from the Smart Grip controls Operation from Smart Grips Activate initial power up by pressing the Pod Power Button Refer Fig 7 2 Use the LIGHTS button to cycle through power settings 3 Turn off lights by pressing and holding the LIGHT button for three seconds Operation from Battery Pods Turn on ligh
7. t by pressing the Power Button on the rear cap Refer Fig 7 2 Press the red button again to change the light output level 3 Turn off light by holding the red button down for three seconds Operation with Stingray Housing Turn light by pressing the red button on the rear cap Refer Fig 7 2 Press the red button again to change the light output level 3 Turn off lights by pressing and holding the red button for three seconds LED Receiver Light Connector Power Button red Operation With Other Brands of Video Housing Turn light by pressing the red button the rear cap Refer Fig 7 2 Press the red button again to change the light output level 3 Turn off light by holding the red button down for three seconds Post Dive Cleaning After each dive you should dunk the lights and pods in fresh water 2 Press the red button to flush out any salt water 3 After you are geared down and completely dried off simply towel dry the lights in a safe dry place Do not leave your lights in the rinse bucket with other equipment Video lights have been damaged by jostling against other products Storage After diving remove your batteries and charge them Leaving your batteries discharged will significantly reduce the life of the battery The lighting system requires no special storing instructions Store as you would any other valuable piece of electronic equipment Other Maintenance CL
8. ute to review common errors which will result in equipment damage or destruction Always remove batteries from battery pods before storage or travel Failure to do so may inadvertently power on the lighting system and possibly cause heat damage e Check the operation of all your equipment several weeks prior to your trip If maintenance or repair is necessary then time is available for both shipping and repair scheduling If a battery pod is flooded immediately remove the battery POD rinse with fresh water good or rubbing alcohol better Shake vigorously towel dry and leave the pod where it can drain excess moisture BATTERY Dry the battery off blow any water out of the connectors and then shake the battery to remove remaining moisture If there is water inside the battery do not attempt to use it again If battery seems damp inside allow it to dry for at least 24 hours away from flammable items Then on land charge the battery and test your lights before attempting another dive Warning Warning Warning Warning Caution The Sunray 2000 LED Lighting System is designed for use underwater Prolonged operation in air may cause the outer surfaces of the light to become hot Light amp Motion recommends that you limit the operation of the Sunray light out of the water to less than two minutes Warning Warning Warning Warning Table of Contents 5 4

Download Pdf Manuals

image

Related Search

Related Contents

Elo Touch Solution 2639L    Pleasant Hearth AH-1201 Instructions / Assembly  建設機械総合カタログ  Installationsanleitung - Bosch Security Systems  Product Manual  Getting started with http://clif.objectweb.org/  LogTag Analyser User guide  第17回定時株主総会招集ご通知 - パナソニック インフォメーション  instruments - Hanna Instruments Portugal  

Copyright © All rights reserved.
Failed to retrieve file