- De Wijnlanden Estate
Contents
1. ON and OFF eee E commands each time the button is Og D pressed To DIM a light when used with a Light Dimmer Enter DIM BRIGHT mode on the Remote control by pressing buttons 1 and 2 simultaneously g a Press and hold the appropriate button on atl gal the Remote Control to dim or brighten G S the light CHRE ght Drima gee The Remote Control will exit the DIM BRIGHT mode automatically if no buttons are pressed for 7 seconds A forced exit can be achieved by pressing buttons 1 and 2 simultaneously again ADVANCED PROGRAMMING Delete A Remote Control channel programmed into a ClickOn receiving device may be deleted from that device by following the procedure below 1 Place the receiving device into the programming mode This is normally done by pressing and holding the button on the receiving device until the receiving device LED starts flashing continuously See receiving device user manual for more information 2 iia Press and hold the appropriate aa button on the remote control until the EEr remote sounds 3 beeps followed w 2 by another set of 4 beeps Check for a confirmation signal from the receiving device See receiving device user manual for more information 3 Exit the programming mode on the receiving device Delete All All remote control channels programmed into ANY ClickOn RECEIVING device can be deleted entirely by using any ClickOn Remote Control The remote control used for2. Chek n 6 Channel Keyring Remote Control Add security and comfort to your lifestyle PROGRAMMING 1 Place the receiving device into the programming mode This is normally done by pressing and holding the button on the receiving device until its LED starts flashing continuously See receiving device user manual for more information 2 DA t Press and hold the DESIRED E a channel button on the Remote B a Control until the remote sounds 3 m beeps approx 10 seconds Check Da for a confirmation signal from the receiving device See receiving device user manual for more information 3 Exit the programming mode on the receiving device Click On 6 Channel Keyring Remote Control Model CL KEY 06 TYPICAL APPLICATIONS e Remote control of any ClickOn Receiving Device e Gate Garage door Control e Remote controlled lighting FEATURES Code hopping Ideal for security complexes No dip switches User friendly programming Compatible with all ClickOn devices Provides ON OFF and DIMMING control with ClickOn dimmers Frequency 433 92Mhz Range 30 to 100m 009625 Ill 2006 ClickOn Technology Pty Ltd http www clickon co za REMOTE CONTROL FUNCTIONS Keep in mind that these functions will be available only after successful programming see PROGRAMMING To switch a device ON or OFF Press and release the button on the o eO Remote Control The remote control will se toggle between the
3. Keypad on the Remote Control by pressing buttons 3 and 4 simultaneously The Remote Control will sound a long beep when the Keypad is locked and any key is pressed on the remote control BATTERY REPLACEMENT If the remote control does not respond to any key presses or the LED fails to come on when a key is held in the battery may need replacement The remote control uses one type 23A 12V battery WARRANTY The manufacturer warrants that the product identified in this manual is free from defects in material or workmanship This warranty is valid for a period of 12 months from date of purchase The manufacturer at its discretion will repair or replace the defective product when returned to the manufacturer via the retailer of the system In the event that no satisfaction can be obtained from the retailer of the system only then can the manufacturer be approached directly by the final purchaser The manufacturer shall not be responsible for any loss or damage of any nature whatsoever whether direct or indirect consequential or otherwise sustained as a result of the use of the product Improper use or mishandling of this product by the purchaser will render this warranty null and void No warranty claims will be entertained without presentation of a valid invoice The manufacturer will charge the purchaser for services rendered outside the warranty period Any implied warranties in respect of this product are expressly excluded No agreement
4. this need not be one that was previously programmed into the device This allows a lost or stolen remote control to be deleted before reprogramming the new remote control 1 Place the receiving device into the programming mode This is normally done by pressing and holding the button on the receiving device until the receiving device LED starts flashing continuously See receiving device user manual for more information e Press and hold any button on the i remote control until the remote sounds 3 beeps then 4 beeps and es then 5 beeps approximately 17 seconds Check for a confirmation signal from the receiving device See receiving device user manual D 9 for more information 3 Exit the programming mode on the receiving device KEYPAD LOCK FUNCTION The keypad lock function can be used to prevent accidental remote control activation Enabling the Keypad Lock Function Before the keypad lock function can be used it has to be enabled as follows Press and hold button 3 and 4 simultaneously until the remote sounds a burst of beeps after approximately 5 seconds The keypad can now be Locking Unlocking the Keypad locked and unlocked see Disabling the Keypad Lock Function Press and hold button 3 and 4 simultaneously until the remote sounds a short beep after approximately 5 seconds The keypad lock function is now disabled Locking Unlocking the Keypad Lock or Unlock the
5. whether implied or referred are binding unless agreed to in writing by the manufacturer CL KEY 06 R4 2 MAR 2006 ClickOn Technology Pty Ltd
Download Pdf Manuals
Related Search