User Manual
Contents
1. Do not leave the device unattended near large pets dog cat that can knock it over The power cord can easily wind round the child s neck The device cannot be used in oxygen rich environments To prevent overuse the device automatically turns off after 1 5 2 minutes After the force shutdown suction can be restarted 3 15 times depending on the suction power The electronics will prevent the device from turning on for 50 minutes For more information please read Chapter 4 of the User Manual Make sure that all units are appropriately attached before using the device Double check if you have inserted the collared tube into the Colibri nozzle after cleaning Do not use the nozzle and the device without the collared tube Do not use more than 5 ml saline solution because if the solution gets into the tube it can cause damage to the device The connection point of the Colibri nozzle should point downwards while in use Stop using the device if mucus or saline solution has been drawn into the tube disconnect it from the mains then empty the nozzle clean and dry the nozzle and the tube check the filter and replace it if it is wet or clogged Make sure that the housing the tube and the Colibri nozzle are not damaged or cracked Do not use the device if you find that it is damaged Replace the damaged part List of soare parts can be found in section Accessories spare parts If rashes or redness appear on the nose of the child after us2. Powering up the device is possible but after turning on the device irregularity occurs If the device does not start to operate under these conditions the replacement of the power cord non warranty is suggested Such malfunctions are due to external im pacts and are not covered by the warranty If you experience unusual phenomena while operating the device e g low suction power smoke emission strong smell the device buzzes or clacks unusually loud it shakes is shorted cannot be adjusted via the control button and does not turn off after 1 5 minutes Due to misuse of the device the replacement warranty is not valid If you experience unusual phenomena while operating the device and the device does not bear traces of physical damage included in the first two points the customers device is eligible for the replacement warranty The replacement happens at the distributor and the costs are to be borne by the manufacturer User manual Version V02 Valid 04 30 2014 Nosiboo babycare nasal aspirator Page 12 16 the babycare nasal aspirator Warranty tasks The distributor of the Nosiboo device is obliged to promptly handle customer complaints based on the aspects included in the chapters Troubleshooting guide and Malfunction management guide of the User manual In case of the existence of the warranty conditions the device has to be replaced immediately The distributor of the de
3. 12 months after the purchase date It will be only validated if the device was used according to its intended purpose and does not bear signs of damage In the next step the existence of malfunctioning has to be cleared And if the malfunction occurred due to the users own fault or if it was no fault of theirs The manufacturer provides 12 months replacement warranty in case of use according to the intended purpose The following checks can be conducted by any user at home or with the distributing merchant or their trustee after presenting the warranty card and the receipt The distributor or the legal entity charged with failure assessment is obliged to fill in the warranty card supplied with the User manual or provide their own warranty document record the steps of troubleshooting in detail and forward it to the manufacturer within 24 hours User manual Version V02 Valid 04 30 2014 Nosiboo babycare nasal aspirator Page 11 16 the babycare nasal aspirator Troubleshooting Visual inspection Detailed description Warranty tasks The entireness of the label on the bottom of the device Other signs of damage on the housing scratches bumps bruises strains scratches around the Traces of contamination on or around the filter Damage of the opening behind the filter grit in the device or traces indicating that grit has been drawn into the device Any kind of contamination of the tube Manual inspection
4. Signs of damage on the label indicate opening of the device housing Signs of damage on the device housing indicate opening of the device housing The excessive contamination of the filter dirt getting into the device indicate the misuse of the device Contamination getting into the tube indicates misuse of the device Due to misuse of the device the replacement warranty is not valid Due to misuse of the device the replacement warranty is not valid Due to misuse of the device the replacement warranty is not valid Due to misuse of the device the replacement warranty is not valid Before operating the device check the connection of the power cord on the device Any kind of failure on the control button Powering up turning on If the connection not the power cord on the device caved in can be moved can be removed turning on and operating the device is life threatening Such malfunctions are due to external impact and are not covered by the warranty If the control button on top of the device is damaged is jammed moves freely or fell off the malfunction is due to external impact and is not covered by the warranty Turning on and operating the device is life threatening Due to misuse of the device the replacement warranty is not valid Due to misuse of the device the replacement warranty is not valid Powering up the device happens with the power cord supplied with the device
5. products are regarded as hazardous waste This is indicated by the following sign on the product packaging B The Colibri nozzle does not present a serious risk to the environment so it can be disposed with household waste 10 Specifications Max motor performance 300 W Adjustable motor performance 140 215 W Differential pressure 0 04 O 12 bar Max air flow 54 min Power supply 230 V 50 60 Hz IP class IP20 Protection class II Type of applied parts BF Applied parts the complete housing Operation type no continuous operation Operation length on 1 min off 50 min Duration of continuous use max 1 min Tripping temperature of the thermal switch 95 C Average housing temperature 30 35 C after 1 min continuous use Noise level 55 62 dB Temperature range 10 C 40 C Relative humidity max 75 The expected life of the housing electrical parts 3 years Expected life of the Nosiboo Colibri nozzle 1 year Diameter of the nasal insertion end of the nozzle min 5 6 mm Length of the nasal insertion end of the nozzle min 32 mm Weight housing 972 g Dimensions housing W x H x D 200 x 155 x 175 mm Dimensions complete package 180 x 180 x 180 mm 11 Accessories soare parts Parts can be ordered from the Specialist service station Attract Kft H 7624 P cs Barbak n t r 5 Tel 36 72 551 642 Mo Fr 8 am 4 pm E mail service nosiboo com User manual Version V02 Valid 04 30
6. 2014 Nosiboo babycare nasal aspirator Page 15 16 the babycare nasal aspirator Photo Reference order number Name ie AC 05 01 blue Colibri head AC 05 02 pink AC 05 03 green AC 03 01 blue Tube AC 03 02 pink ANV AC 03 03 green AC 04 01 Filter AC 01 01 Power cord EU 2 AC 02 01 Power cord UK CO 01 01 blue Colibri head tube CO 01 02 pink CO 01 03 green User manual Version V02 Valid 04 30 2014 Nosiboo babycare nasal aspirator Page 16 16 International warranty card The guarantee is valid for 12 months after the purchase date It will be only validated if the device was used according to its intended purpose and does not bear signs of damage Warranty is validated at the authorised distributor of the device The authentic distributor invoice has to be presented The distributor of the Nosiboo device is obliged to promptly handle customer complaints based on the aspects included in chapters Troubleshooting guide and Malfunction management guide of the User manual In case of the existence of the warranty conditions the device has to be replaced immediately The distributor of the device is obliged to keep a written record about the troubleshooting This can be done within the framework of the distributor s internal documentation or in the warranty card supplied with the User manual It has to contain the perceived malfunction the date and the unique serial number to
7. USER MANUAL 2 reddot award 2014 winner Nosiboo babycare nasal aspirator ATTRACT KFT T 36 72551642 contact nosiboo com P m H 7624 P cs Barbak nt r5 F 3672551643 www nosiboo com CE version VO2 Valid 04 30 2014 Page 1 16 the babycare nasal aspirator Table of contents Package contents Foreword Warning and security signs Important security regulations 1 Intended use 2 Product introduction 3 First time operation 4 Instructions for use 5 Troubleshooting malfunctions 6 Maintenance and storage 7 Cleaning 8 Important information about reducing the electromagnetic interferences 9 Environment 10 Specifications 11 Accessories spare parts NN Oo BR WW W 13 13 14 15 15 15 User manual Version VO2 Valid 04 30 2014 Nosiboo babycare nasal aspirator Page 2 16 the babycare nasal aspirator Package contents Colibri nozzle Power cord User manual Device Tube Foreword Dear customer We would like to congratulate you on buying our Red Dot Design Awarded Nosiboo babycare nasal aspirator Please read this user manual carefully so that you ll be able to use the nasal aspirator for years and can prevent illnesses for a long time BH Please read the user manual carefully before using the device Warning and safety signs You may see the following signs in the user manual or on the label of the device Explanation Type BF applied parts increase
8. aking blood thinning medicines in case of congenital malformations e g cleft palate Suggested user Age adult over 18 Sex not applicable man or woman Knowledge should have general knowledge according to their age Education min primary school education no need for special knowledge to use the device Knowledge of the User manual included in the package t User manual Version V02 Valid 04 30 2014 Nosiboo babycare nasal aspirator Page 6 16 the babycare nasal aspirator 2 Product introduction On Off control button Power card ox Tube SS SD Nozzle housing Replaceable filter N Housing side N connecting member SI 9 Collared tube gt A Shi Nozzle housing whit connection Figure 1 Nosiboo babycare nasal aspirator 3 First time operation Assembling the Colibri nozzle aRoNn gt Clean the parts of the nozzle see section Cleaning and maintenance Insert the collared tube into the nozzle housing that is supplied with a connection Place the nozzle member that has no connection in the right position Push the flexible nozzle end on the joint collar Attach one end of the tube to the nozzle Attaching the device 6 Attach the free end of the tube to the device housing 7 Attach one end of the 230 V mains cord to the plug on the lower part of the device housing then the other end to the socket The device is ready for use User ma
9. and other formulations suggested by physicians should be used after the aspiration The suggested length of the aspiration is 10 seconds nasal opening but the device should not be used longer than 80 seconds at a time In case of overuse the device will automatically switch off due to security reasons and can be switched on only after a given time In case we have to interrupt the operation we should switch off the device After the engine stops working we can restart the one minute treatment period If the device is working for more than 1 minute and 20 seconds the power will go down on 45 to indicate that the suggested treatment time is over In this case it can be restarted again after turning it off depending on the previously used suction power for limited times User manual Version V02 Valid 04 30 2014 Nosiboo babycare nasal aspirator Page 9 16 the babycare nasal aspirator Some examples regarding the restarts depending on the set Max rate Mid rate Min rate In this case after the 1 minute In this case after the 1 minute In this case after the 1 minute and 20 seconds long treatment and 20 seconds long treatment and 20 seconds long treatment time the device can be time the device can be time the device can restarted 2 times restarted 5 times be restarted 10 14 times Depending on the density of the mucous The Nosiboo babycare nasal aspirator can be used several times a day It is recommended to c
10. be found on the label on the bottom of the device 7 Name and address of distributor To be completed by the distributor Serial number of the Nosiboo nasal aspirator to be found on the bottom of the device on the label Purchase date Type of malfunction Date of malfunction Countersignature of distributor date signature and seal a Name and address of distributor To be completed by the distributor Serial number of the Nosiboo nasal aspirator to be found on the bottom of the device on the label Purchase date Type of malfunction Date of malfunction Countersignature of distributor date signature and seal The expressed warranty does not affect the consumer s implied warranty rights Manufacturer and specialist service station Attract Kft Hungary H 7624 P cs Barbak n t r 5 Tel 36 72 551 642 Mo Fr 8 am 4 pm E mail service nosiboo com
11. d protection R E F against electrick shock Reference order number Class II device double insulation SN Serial number Name and address of the manufacturer Keep dry The housing prevents subjects bigger than Read the user manual IP20 12 5 mm from getting into the device The housing does not prevent liquids from infiltrating into the device it a Warning ontmin Intermittent operation off 50 min a i f Lil A User manual Version V02 Valid 04 30 2014 Nosiboo babycare nasal aspirator Page 3 16 the babycare nasal aspirator Important security regulations Warning N If possible emergencies below are not avoided user injury or even a fatal accident may occur Safety regulations regarding general use E E E He E 3 ee E E E 3 The device can be used exclusively for removing the nasal mucus from a child s nose It cannot be used for any other purpose It is FORBIDDEN to use the device in the bathroom or any other humid or wet environment Stop using the device if liquid or solid has been drawn into the housing Contact a qualified service centre The device can only be used by adults While in use the device should be in a stable position standing on a level surface Do not lay the child on their back and do not block the free nasal opening while using the device Do not leave the device unattended near children or people with reduced physical or mental abilities
12. e e g in a cabinet Replaceble filter TA ise side i d A If you have more children it is recommended to use a ee aad T9 separate nozzle with each child and to keep their own be nozzle separately and marked Figure 4 Replacing the filter Do not store near a heat source 7 Cleaning Cleaning the Colibri nozzle is easy After removing the tube and the flexible tip the nozzle housing can be taken apart Thereafter wash it in lukewarm water disinfect it in disinfectant and let it dry Recommended disinfectant Chicco Disinfectant User manual Version V02 Valid 04 30 2014 Nosiboo babycare nasal aspirator Page 13 16 the babycare nasal aspirator Dismountable nozzle housing Removable flexibla and Before cleaning the device detach the tube from the housing ZN 2 and the Colibri nozzle Wash it in lukewarm tap water disinfect it in 3 ye disinfectant and then let it dry gt SANS eS A N Recommended disinfectant A SH Chicco Disinfectant If the parts are dry store the device in a place that is protected from contamination so that you can immediately use Removable it next time flexible 1 Collared Hubs Clean the device housing with a tube dry and soft cloth do not use any connection Please insert the collared tube detergents or chemicals into the nozzle housing after cleaning and before using Figure 5 Cleaning of the Colibri nozzle 8 Importan
13. ing the device do not use the device again Consult a physician Use the device exclusively with the tube and nozzle supplied by the manufacturer Do not attach the nozzle to any other devices User manual Version V02 Valid 04 30 2014 Nosiboo babycare nasal aspirator Page 4 16 the babycare nasal aspirator Safety regulations about connecting the device to the mains x Protect the power cord against damage Do not break it do not place heavy items on it because a damaged cord may cause electric shock x Keep the power cord away from heat e g furnace heater and convector because it can cause damage to the isolation x Use the device only if the tube is dry x Do not remove the mounting screws of the housing Do not reconstruct the device for other purposes x The use of the device is forbidden if there is a breakage or crack on the housing or on the power cord due to misuse x Incase of unexpected failure or malfunction immediately switch off the device and interrupt the power supply by unplugging it from the mains Safety regulations regarding the next use of the device x Always disinfect the nozzle after use x Do not leave the parts of the dismounted Colibri nozzle within reach of children because they may swallow these General precautions x Read and follow the instructions of the Important information to reduce electromagnetic interferences section Read and follow the instructions of the Envir
14. lear the airways before sleeping time and feeding to ensure the peaceful breathing of the child Do not cause pain to the child introduce the device and the method in a tolerant way Always switch off the device after use with the control button The motor will operate for while to cool down after you have switched off the device Do not unplug the device from the mains until it completely shuts down Do not cover the ventages on the back of the device while in use Recommended frequency of use If necessary 2 3 times a day for 10 seconds nasal opening at a time Do not operate the nasal aspirator continuously for more than 1 minute After 1 minute continuous use wait 50 minutes before switching it on again 5 Troubleshooting malfunctions If you suspect malfunctioning of the Nosiboo device please read the next two chapters As the first step the Troubleshooting guide provides suggestions for resolving concrete problems In the chart you can find the problems and the troubleshooting suggestions If these suggestions do not solve the problem the Malfunction management guide helps you your merchant distributor in localizing the malfunction as soon as possible and in assessing the possibility of the replacement guarantee Please study these chapters in detail in case of a malfunction User manual Version V02 Valid 04 30 2014 Nosiboo babycare nasal aspirator Page 10 16 the babycare nasal aspirator Troubleshooting g
15. nual Version V02 Valid 04 30 2014 Nosiboo babycare nasal aspirator Page 7 16 the babycare nasal aspirator 4 Instructions for use Before use the device should be placed in such a way that the plug of the power cord can be easily pulled out from the socket You can turn the device on or off by pushing and control the intensity of the suction by turning the button on top of the housing Adjustability guarantees that after selecting the appropriate suction power the parent cannot cause any secondary deformation in the nose Before turning on the device find the right airflow rate fit for your child s age based on the figure below Adjusting the suction Power at max suction 0 12 bar Figure 2 Adjusting the suction power The minimum value of the scale is suitable for newborns the middle value for babies and the maximum value for small children and for preschoolers The effectiveness of the device is highly influenced by the thickness of the mucus the extent of the disease and the unique anatomy of the child If the mucus is thin you can use the device at a lower setting if it is thick you can use the device at a higher setting than usually The device can be operated exclusively by adults Do not give the device ready for use to the child Hold the child in a stable position while using the device Sit your child onto your lap and hold them or sit them into a straight position while supporting their back with a pill
16. onment section if you would like to dispose of the device or any part of it 1 Intended use The Nosiboo babycare nasal aspirator was designed to remove the nasal mucus from the child s nose The vacuum and airflow needed for the aspiration is created by an aspirating device designed specifically for this purpose The Colibri nozzle which is inserted into the nose is connected to this device via a tube The Colibri nozzle has a patented design that prevents the mucus from entering the device User manual Version V02 Valid 04 30 2014 Nosiboo babycare nasal aspirator Page 5 16 the babycare nasal aspirator Intended purpose x to ensure nasal breathing to infants x to prevent the complications of childhood common cold and to accelerate the healing process by aspirating the nasal mucus x torelieve childhood allergy like symptoms by removing the nasal mucus Patients to be treated children who are typically under the age of 6 unable to remove the nasal mucus by blowing their noses Illness condition requiring treatment indication x to eliminate clogging of the nose treatment of common cold and auxiliary treatment of superinfected paranasal sinuses supplementary treatment of the allergic infectious condition Conditions in which the device cannot be used contraindication haemophilia if the blood vessels of the nasal septum s mucous membrane widen in case of frequent nosebleed while t
17. ow You may also sit them into a resting chair with a tilted back AN Do not lay your child on their back and do not block the free nasal opening Insert the previously disinfected Colibri nozzle into the child s nose and then turn on the device by pushing the control button the device operates at the setting used last time User manual Version V02 Valid 04 30 2014 Nosiboo babycare nasal aspirator Page 8 16 the babycare nasal aspirator Correct positioning of the Colibri nozzle Push the tip of the Colibri nozzle into the nose The tip should point slightly downwards and outwards towards he eyeball In this position you can gently move the Colibri nozzle With this method you can reach the opening leading to the maxillary sinus and you will not hurt the mucous membrane of the nasal concha or the capillaries of the nasal septum he connection of the flexible tube should point downwards while in use The patented desing of the Colibri nozzle can hold up to 5 ml thin liquid and prevents the mucus from entering the lexible tube Dry and very thick mucus can be dissolved by saline solutions Do not use more than 5 ml of these at a time because if liquid gets into the tube it can damage the device After injecting the solution wait a few minutes remove the mucus running out with a tissue Only after this should the nasal aspirator be used Figure 3 Correct positioning of the Colibri nozzle Nose drops
18. t information about reducing electromagnetic interferences The home wireless network equipment mobile phones and wireless phones may affect the operation of medical equipment as electromagnetic interference can occur between devices Electromagnetic interference may cause harmful interference in the operation of medical devices and therefore emergency situations may occur Due to the above mentioned reasons medical devices mustn t interfere with any other equipment To guarantee the electromagnetic compatibility the necessary requirements were fixed in standards The standards define the protection level of the medical device and the maximum value of the electromagnetic radiation emitted by these The Nosiboo babycare nasal aspirator complies with the requirements of EN 60601 1 2 2007 In spite of that you should follow the instructions below while using the device User manual Version V02 Valid 04 30 2014 Nosiboo babycare nasal aspirator Page 14 16 the babycare nasal aspirator Do not use your cell phone or wireless phone or any other device emitting strong electromagnetic radiation near the device Otherwise the device may malfunction which can cause an emergency Itis recommended to keep at least 5 m distance between the devices Check the proper operation of the device if this distance is shorter 9 Environment Do not dispose of the device at the end of the product life with household waste because electronic
19. uide Malfunction The suction intensity decreased The suction intensity decreased Liquid or mucus got into the tube Liquid or mucus got into the tube The device cannot be switched on The device cannot be switched on Reason he plug is not connected he device switched off due to overuse for security reasons he nozzle got blocked or was incorrectly assembled he filter wore out The nozzle was not held in the correct position The connection point of the tube did not point downwards Too much saline solution was used Recommendation Connect the power cord to the device then to the 230 V socket For the sake of your child s health stop using the nasal aspirator The device can be used again in 50 minutes Take it apart and clean the it finally assemble it based on the user manual Replace the filter based on the user manual s Maintenance and storage section Switch off the device and clean and dry he nozzle and the tube Check the filter and replace it if necessary Reduce the volume of the saline solution o less than 5 ml Switch off the device and clean it then dry the nozzle and the tube Check the filter and replace it if necessary If the device does not work properly in spite of performing the instructions of the troubleshooting guide check the Malfunction management guide with the distributor merchant Malfunction management guide The guarantee is valid for
20. vice is obliged to keep a written record about the troubleshooting This can be done within the framework of the distributor s internal documentations or in the warranty card supplied with the User manual It has to contain the perceived malfunction the date and the unique serial number to be found on the label on the bottom of the device Specialist service station contact details Attract Kft H 7624 P cs Barbak n t r 5 Tel 36 72 551 642 Mo Fr 8 am 4 pm E mail service nosiboo com 6 Maintenance and storage Only after the cooling process has stopped should the power cord be unplugged from the mains and from the device Disconnect the tube from the device and the nozzle There is a special filter behind the housing side connection Replacement of the filter element may be due after 300 treatments or after 1 year in case of intensive use In case of rarer use if the OE filter element is not contaminated it can be used for a longer time The filter can be replaced after turning the housing side connection member Remove the worn out filter and insert the supplied spare filter Order number of the filter is AC 04 01 In the event of an unexpected drop in the performance aK it is recommended to check the filter before the end of control button the cycle Clean the housing with a dry soft cloth do not use any 0 a Pre detergents or chemicals Keep the device in a closed space where it is protected from dust and damag
Download Pdf Manuals
Related Search